Victron energy MultiPlus 1600VA Manuale del proprietario

Manual

EN

Handleiding

NL

Manuel

FR

Anleitung

DE

Manual

ES

Manuale

IT

Appendix

MultiPlus 1600VA

MultiPlus 12 | 1600 | 70 230V

MultiPlus 24 | 1600 | 40 230V

MultiPlus 48 | 1600 | 20 230V

1

EN NL FR DE ES IT Appendix

1. SAFETY INSTRUCTIONS

General

Please familiarize yourself with the safety features and instructions by first reading the

documentation supplied with this product before using the equipment. This product has

been designed and tested in accordance with international standards. The equipment must

be used exclusively for the purpose for which it was designed.

WARNING: ELECTRIC SHOCK HAZARD

The product is used in conjunction with a permanent energy source (battery). Input and/or

output terminals may still be dangerously energized, even when the equipment is switched

off. Always switch off the AC supply and the battery before carrying out maintenance or

servicing the product.

The product has no internal user-serviceable components. Do not remove the front plate or

operate the product if any panels have been removed. All servicing must be undertaken by

qualified personnel.

Never use the product where there is a risk of gas or dust explosions. Consult the battery

manufacturer's information to ascertain that the product is intended for use in conjunction

with the battery. Always comply with the battery manufacturer's safety instructions.

Never try to charge non-rechargeable - or frozen batteries.

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety. Children should be supervised to ensure that they do not play with the appliance

WARNING: Do not lift heavy loads without assistance.

Installation

Read the installation instructions in the installation manual before installing the equipment.

This is a Safety Class I product (supplied with a protective grounding terminal).

Uninterruptible protective grounding must be provided at the AC input and/or output

terminals. Alternatively, the grounding point located externally on the product may be

used. Whenever it is likely that the grounding protection has been damaged, the product must

be turned off and secured against unintended operation; please contact qualified service staff.

Ensure that the DC and AC input cables are fused or fitted with circuit breakers.

Ensure that the equipment is used under the correct ambient conditions. Never operate the

product in a wet or dusty environment. Ensure there is adequate free space for ventilation

around the product and check that the ventilation vents are not blocked.

Ensure that the required system voltage does not exceed the product's capacity.

2

Transport and Storage

Ensure that the mains power and battery leads have been disconnected before storing or

transporting the product.

No liability can be accepted for any transport damage if the equipment is shipped in non-

original packaging.

Store the product in a dry environment; the storage temperature must be between -40°C and

70°C.

Consult the battery manufacturer's manual in respect of transport, storage, charging,

recharging and disposal of the battery.

3

EN NL FR DE ES IT Appendix

2. DESCRIPTION

2.1 General

Multifunctional

The Multi gets its name from the multiple functions it can perform. It is a powerful true sine

wave inverter, a sophisticated battery charger that features adaptive charge technology and

a high-speed AC transfer switch in a single enclosure. Beside these primary functions,

however, the Multi has several advanced features that provide a range of new applications

as outlined below.

Uninterrupted AC power

In the event of a grid failure, or shore or generator power being disconnected, the inverter

within the Multi is automatically activated and takes over supply to the connected loads.

This happens so fast (less than 20 milliseconds) that computers and other electronic

equipment will continue to operate without disruption.

Parallel and 3-phase operation capability

Up to 6 inverters can operate in parallel to achieve higher power output.

Operation in 3-phase configuration is also possible.

PowerControl – Dealing with limited generator or shore side power

With a Multi Control Panel a maximum generator or shore current can be set. The Multi will

then take account of other AC loads and use whatever is extra for charging, thus preventing

the generator or shore supply from being overloaded.

PowerAssist – Boosting the capacity of shore or generator power

This feature takes the principle of PowerControl to a further dimension allowing the

MultiPlus Compact to supplement the capacity of the alternative source. Where peak power is

so often required only for a limited period, it is possible to reduce the size of generator needed

or conversely enable more to be achieved from the typically limited shore connection. When

the load reduces, the spare power is used to recharge the battery.

Programmable relay

The Multi is equipped with a programmable relay that by default is set as an alarm relay. The

relay can be programmed for all kinds of other applications however, for example as a starter

relay for a generator.

2.2 Battery charger

Adaptive 4-stage charging characteristics: bulk – absorption – float – storage

The microprocessor-driven adaptive battery management system can be adjusted for various

types of batteries. The adaptive function automatically adapts the charging process to battery

use.

The right amount of charge: variable absorption time

In the event of slight battery discharge, absorption is kept short to prevent overcharging and

excessive gas formation. After deep discharging, the absorption time is automatically

extended in order to fully charge the battery.

4

Preventing damage due to excessive gassing: the BatterySafe mode

If, in order to quickly charge a battery, a high charge current in combination with a high

absorption voltage has been chosen, damage due to excessive gassing will be prevented by

automatically limiting the rate of voltage increase once the gassing voltage has been reached.

Less maintenance and aging when the battery is not in use: the Storage mode

The Storage mode kicks in whenever the battery has not been subjected to discharge during

24 hours. In the Storage mode float voltage is reduced to 2,2V/cell (13,2V for 12V battery) to

minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back

to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the

electrolyte and sulphation, a major cause of early battery failure.

Two DC outputs for charging two batteries

The main DC terminal can supply the full output current. The second output, intended for

charging a starter battery, is limited to 1A and has a slightly lower output voltage.

Increasing service life of the battery: temperature compensation

The temperature sensor (supplied with the product) serves to reduce charging voltage when

battery temperature rises. This is particularly important for maintenance-free batteries, which

could otherwise dry out by overcharging.

More on batteries and charging

Our book ‘Energy Unlimited’ offers further information on batteries and battery charging, and

is available free of charge on our website (see www.victronenergy.com  Support &

Downloads’  General Technical Information). For more information on adaptive charging,

please also refer to the General Technical Information on our website.

2.3 Self consumption – solar energy storage systems

When the Multi is used in a configuration in which it will feed back energy to the grid it is

required to enable grid code compliance by selecting the grid code country setting with the

VEConfigure tool.

Once set, a password will be required to disable grid code compliance or change grid code

related parameters.

If the local grid code is not supported by the Multi an external certified interface device should

be used to connect the Multi to the grid.

5

EN NL FR DE ES IT Appendix

3. OPERATION

3.1 On / Off / Charger-only Switch

When switched to ‘on’, the product is fully functional. The inverter will come into operation

and the LED ‘inverter on’ will light up.

An AC voltage connected to the ‘AC in’ terminal will be switched through to the ‘AC out’

terminal, if within specifications. The inverter will switch off, the ‘Charger’ LED will light up

and the charger commences charging. If the voltage at the ‘AC-in’ terminal is not within

specifications, the inverter will switch on.

When the switch is switched to ‘charger only’, only the battery charger of the Multi will

operate (if mains voltage is present). In this mode input also is switched through to the ‘AC

out’ terminal.

NOTE: When only the charger function is required, ensure that the switch is switched to

‘charger only’. This prevents the inverter from being switched on if the mains voltage is lost,

thus preventing the batteries from running flat.

3.2 Remote control

Remote control is possible with a switch or with a Multi Control panel.

The Multi Control panel has a simple rotary knob with which the maximum current of the AC

input can be set: see PowerControl in Section 2.

6

3.3 LED Indications

Inverter/Charger/

On / Off / Charger-only switch = On

The inverter is switched on and supplies power to the load.

On / Off / Charger-only switch = On

The inverter is switched on and supplies power to the load.

Pre-alarm: overload, or

battery voltage low, or

inverter temperature high.

On / Off / Charger-only switch = On

The inverter is switched off due to one of the following alarms:

overload, or

battery voltage low, or

inverter temperature high, or

DC ripple voltage too high.

On / Off / Charger-only switch = On

The AC input voltage is switched through and the charger operates in

float mode.

On / Off / Charger-only switch = On.

PowerControl and PowerAssist:

The AC input is switched through and the charge current is zero.

The inverter is switched on and, in case of PowerAssist, assists the AC

input by supplying additional power to the load (see section 2.1).

On / Off / Charger-only switch = On.

Energy Storage System (ESS):

The AC input voltage is switched through.

The inverter is switched on and supplies power to the load, or excess

power to the mains.

LED off

LED flashes

LED illuminated

7

EN NL FR DE ES IT Appendix

Charger only

On / Off / Charger-only switch = Charger only

The AC input voltage is switched through and the charger operates in

bulk or absorption mode.

On / Off / Charger-only switch = Charger only

The AC input is switched through and the charger operates in float or

storage mode.

Note: the Multi will shut down if four abnormal events occur within 30 seconds.

The Multi can be reset by switching to Off and then to On.

8

4. INSTALLATION

4.1 Location

The product must be installed in a dry and well-ventilated area, as close as possible to the

batteries. There should be a clear space of at least 10cm around the appliance for cooling.

For mounting see G

For safety purposes, this product should be installed in a heat-resistant

environment. Prevent the presence of e.g. chemicals, synthetic components,

curtains or other textiles, etc., in the immediate vicinity.

4.2 Connection of the Battery cables

In order to fully utilize the full capacity of the product, batteries with sufficient capacity and

battery cables with sufficient cross section should be used. See table below:

12/1600/70 24/1600/40 48/1600/20

Recommended

cross section (mm

2

)

1,5  5 m

50

25

16

Recommended

battery capacity (Ah)

200 - 700 100 - 400 40 - 200

Procedure

Proceed as follows to connect the battery cables:

Connect battery cables to the Multi and battery, see appendix A.

Reverse polarity connection will cause damage to the product. (Safety fuse inside the Multi

can be damaged).

Use PZ 2 screwdriver for the Multi 48V 1600VA

Use Flatscrewdriver 6.5mm for Multi 24V 1600VA

Use Hex key 5mm for Multi 12V 1600VA

This product should be installed by a qualified electrician.

a. Excessively high ambient temperature will result in the following:

- Reduced service life.

- Reduced charging current.

- Reduced peak capacity, or shutdown of the inverter.

b. Never mount the product directly above the batteries.

9

EN NL FR DE ES IT Appendix

Internal DC Fuses

All servicing must be undertaken by qualified personnel.

4.3 Connection of the AC cabling

The Multi is provided with a ground relay (relay H, see appendix B) that automatically

connects the Neutral output to the chassis if no external AC supply is available. If an

external AC supply is provided, the ground relay H will open before the input safety relay

closes. This ensures the correct operation of an earth leakage circuit breaker that is

connected to the output.

- In a fixed installation, uninterruptable grounding can be secured by means of the

grounding wire of the AC input. Otherwise the casing must be grounded.

- In a mobile installation, interrupting the shore connection will simultaneously disconnect

the grounding connection. In that case, the casing must be connected to the chassis (of the

vehicle) or to the hull or grounding plate (of the boat).

- In case of a boat, direct connection to the shore ground is not recommended because of

potential galvanic corrosion. The solution to this is using an isolation transformer.

The mains input & output terminal connector can be found on the bottom of the Multi, see

appendix A. The shore or mains cable must be connected to the connector with a three-wire

cable. Use a three-wire cable with a flexible core and a cross section of at least 1.5mm².

Procedure (see appendix A)

Proceed as follows to connect the AC cables:

The AC output cable can be connected directly to the male-connector. (the connector pulls

out!)

The terminal points are indicated clearly. From left to right: ‘N’ (neutral), earth, and ‘L1’

(phase).

The AC input cable can be connected directly to the female-connector. (the connector pulls

out!)

The terminal points are indicated clearly. From left to right: ‘L1’ (phase), earth, and ‘N’

(neutral).

Push the ‘input’ connector into the AC-in connector.

Push the ‘output’ connector into the AC-out connector.

1600VA

12V - 24V

1600VA

48V

Automotive Bolt-Down Fuse

MIDI or BF1 fuse 32V

200A – 125A

-

MIDI or BF1 fuse 58V

-

60A

This is a Safety Class I product (supplied with a protective grounding terminal).

Uninterruptible protective grounding must be provided at the AC input

and/or output terminals and/or chassis grounding point located externally

on the product.

10

4.4 Optional Connections

A number of optional connections are possible:

Undo the four screws at the front of the enclosure and remove the front panel.

4.4.1 Second Battery

The Multi has a connection (+) for charging a starter battery. For connection see appendix A.

Trickle charge output is protected by automatic overcurrent & overload protection (trip current

1A Imax= 5,5A)

4.4.2 Temperature Sensor

The temperature sensor supplied with the product may be used for temperature-compensated

charging. The sensor is insulated and must be mounted on the battery minus pole. Default

output voltages for Float and Absorption are at 25°C. In adjust mode temperature

compensation is disabled.

4.4.3 Remote Control

The product can be remotely controlled in two ways:

- With an external on/off switch (Remove Link “Remote Switch connector H”)

- With a Multi Control Panel

Please see section 5.4 for appropriate DIP switch settings.

4.4.4. Programmable relay

The Multi is equipped with a multi-functional relay that by default is programmed as an alarm

relay. The relay can be programmed for all kinds of other applications however, for example to

start a generator (VEConfigure software needed).

4.4.5 Parallel Connection (see appendix C)

The MultiPlus can be connected in parallel with several identical devices. To this end, a

connection is established between the devices by means of standard RJ45 UTP cables. The

system (one or more MultiPlus units plus optional control panel) will require subsequent

configuration (see Section 5).

In the event of connecting MultiPlus units in parallel, the following requirements must be met:

- A maximum of six units connected in parallel.

- Only identical devices may be connected in parallel.

- The DC connection cables to the devices must be of equal length and cross-section.

- If a positive and a negative DC distribution point is used, the cross-section of the connection between the

batteries and the DC distribution point must at least equal the sum of the required cross-sections of the

connections between the distribution point and the MultiPlus units.

- Place the MultiPlus units close to each other, but allow at least 10 cm for ventilation purposes under,

above and beside the units.

- A battery-temperature sensor need only be connected to one unit in the system. If the temperature of

several batteries is to be measured, you can also connect the sensors of other MultiPlus units in the system

(with a maximum of one sensor per MultiPlus). Temperature compensation during battery charging

responds to the sensor indicating the highest temperature.

- Only one remote can be connected to the system.

11

EN NL FR DE ES IT Appendix

4.4.6 Three-phase operation (see appendix D)

The MultiPlus can also be used in 3-phase wye (Y) configuration. To this end, a connection

between the devices is made by means of standard RJ45 UTP cables (the same as for

parallel operation). The system (MultiPlus units plus an optional control panel) will require

subsequently configuration (see Section 5).

Pre-requisites: see Section 4.4.5.

5. CONFIGURATION

Settings may only be changed by a qualified engineer

Carefully read the instructions before changes are made.

Batteries should be placed in a dry and well-ventilated area during charging.

5.1 Standard settings: ready for use

On delivery, the Multi is set to standard factory values. In general, these settings are

suitable for single-unit operation.

Warning: Possibly, the standard battery charging voltage is not suitable for your

batteries! Refer to the manufacturer's documentation or to your battery supplier!

Standard Multi factory settings

Inverter frequency 50 Hz

Input frequency range 45 - 65 Hz

Input voltage range 180 - 265 VAC

Inverter voltage 230 VAC

Stand-alone / parallel / 3-phase stand-alone

Search mode off

Ground relay on

Charger on/ off on

Battery charge algorithm four-stage adaptive with BatterySafe mode

Charge current 100% of the maximum charge current

Battery type Victron Gel Deep Discharge (also suitable

for Victron AGM Deep Discharge)

Automatic equalisation charging off

Absorption voltage 14.4 / 28.8 / 57,6V

Absorption time up to 8 hours (depending on bulk time)

Float voltage 13.8 / 27.6 / 55,2V

Storage voltage 13.2 / 26.4 / 52,8V (not adjustable)

Repeated absorption time 1 hour

Absorption repeat interval 7 days

Bulk protection off

AC input current limit 12A (= adjustable current limit for PowerControl and

PowerAssist functions)

UPS feature on

Dynamic current limiter off

WeakAC off

BoostFactor 2

Programmable relay alarm function

12

5.2 Explanation of settings

Settings that are not self-explanatory are described briefly below. For further information,

please refer to the help files in the software configuration programs (see Section 5.3).

Inverter frequency

Output frequency if no AC is present at the input.

Adjustability: 50Hz; 60Hz

Input frequency range

Input frequency range accepted by the Multi. The Multi synchronises within this range with the

AC input frequency. The output frequency is then equal to the input frequency.

Adjustability: 45 – 65Hz; 45 – 55Hz; 55 – 65Hz

Input voltage rangeVoltage range accepted by the Multi. The Multi synchronises within this

range with the AC input voltage. The output voltage is then equal to the input voltage.

Adjustability:

Lower limit: 180 - 230V

Upper limit: 230 - 270V

Inverter voltage

Output voltage of the Multi in battery operation.

Adjustability: 210 – 245V

Stand-alone / parallel operation / 2-3 phase setting

Using several devices, it is possible to:

increase total inverter power (several devices in parallel)

create a split-phase system

create a 3-phase system.

The standard product settings are for standalone operation. For parallel, or three phase

operation see section 4.4.5 and 4.4.6.

Search mode

If search mode is ‘on’, the power consumption in no-load operation is decreased by approx.

70%. In this mode the Multi, when operating in inverter mode, is switched off in case of no

load or very low load, and switches on every two seconds for a short period. If the output

current exceeds a set level, the inverter will continue to operate. If not, the inverter will shut

down again.

Search Mode can be set with a DIP switch.

Search Mode ‘shut down’ and ‘remain on’ load levels can be set with VEConfigure.

The standard settings are:

Shut down: 30 Watt (linear load)

Turn on: 60 Watt (linear load)

AES (Automatic Economy Switch)

Instead of the search mode, the AES mode can also be chosen (with help of VEConfigure

only).

If this setting is turned ‘on’, the power consumption in no-load operation and with low loads is

decreased by approx. 20%, by slightly 'narrowing' the sinusoidal voltage.

13

EN NL FR DE ES IT Appendix

Ground relay (see appendix B)

With this relay (H), the neutral conductor of the AC output is grounded to the chassis when

the back-feed safety relay is open. This ensures the correct operation of earth leakage

circuit breakers in the output.

If a non-grounded output is required during inverter operation, this function must be turned

off.

(Use VEConfigure)

The standard setting is ‘Four-stage adaptive with BatterySafe mode’. See Section 2 for a

description.

This is the recommended charge curve. See the help files in the software configuration

programs for other features.

Battery type

The standard setting is the most suitable for Victron Gel Deep Discharge, Gel Exide A200,

and tubular plate stationary batteries (OPzS). This setting can also be used for many other

batteries: e.g. Victron AGM Deep Discharge and other AGM batteries, and many types of

flat-plate flooded batteries. Four charging voltages can be set with DIP switches.

Automatic equalisation charging

This setting is intended for tubular plate traction batteries. During absorption the voltage

limit increases to 2,83V/cell (34V for a 24V battery) once the charge current has tapered

down to less than 10% of the set maximum current.

Absorption time

The absortion time depends on the bulk time (adaptive charge curve), so that the battery is

optimally charged. If the ‘fixed’ charging characteristic is selected, the absorption time is

fixed. For most batteries, a maximum absorption time of eight hours is suitable. If an extra

high absorption voltage is selected for rapid charging (only possible for open, flooded

batteries!), four hours is preferable. With DIP switches, a time of eight or four hours can be

set. For the adaptive charge curve, this determines the maximum absorption time.

Storage voltage, Repeated Absorption Time, Absorption Repeat Interval

See Section 2.

Bulk Protection

Default setting: off. When this setting is ‘on’, the bulk charging time is limited to 10 hours. A

longer charging time could indicate a system error (e.g. a battery cell short-circuit).

AC input current limit

These are the current limit settings at which PowerControl come into operation. The factory

setting is 12A.

UPS feature

If this setting is ‘on’ and AC on the input fails, the Multi switches to inverter operation

practically without interruption. The Multi can therefore be used as an Uninterruptible Power

Supply (UPS) for sensitive equipment such as computers or communication systems.

The output voltage of some small generator sets is too unstable and distorted for using this

setting* – the Multi would continually switch to inverter operation. For this reason, the setting

can be turned off. The Multi will then respond less quickly to AC input voltage deviations. The

switchover time to inverter operation is consequently slightly longer, but most equipment

(most computers, clocks or household equipment) is not adversely impacted.

14

Recommendation: Turn the UPS feature off if the Multi fails to synchronise, or continually

switches back to inverter operation.

*In general, the UPS setting can be left ‘on’ if the Multi is connected to a generator with a

‘synchronous AVR regulated alternator’.

The UPS mode may have to be set to ‘off’ if the Multi is connected to a generator with a

‘synchronous capacitor regulated alternator’ or an asynchronous alternator.

Dynamic current limiter

Intended for generators, the AC voltage being generated by means of a static inverter (so-

called ‘inverter’ generators). In these generators, rpm is down-controlled if the load is low: this

reduces noise, fuel consumption and pollution. A disadvantage is that the output voltage will

drop severely or even completely fail in the event of a sudden load increase. More load can

only be supplied after the engine is up to speed.

If this setting is ‘on’, the Multi will reduce charge current until the set current limit is reached.

This allows the generator engine to get up to speed.

This setting is also often used for ‘classic’ generators that respond slowly to sudden load

variation.

WeakAC

Strong distortion of the input voltage can result in the charger hardly operating or not

operating at all. If WeakAC is set, the charger will also accept a strongly distorted voltage, at

the cost of greater distortion of the input current.

Recommendation: Turn WeakAC on if the charger is hardly charging or not charging at all

(which is quite rare!). Also turn on the dynamic current limiter simultaneously and reduce the

maximum charging current to prevent overloading the generator if necessary.

BoostFactor

Change this setting only after consulting with Victron Energy or with an engineer trained by

Victron Energy!

Programmable relay

By default, the programmable relay is set as an alarm relay, i.e. the relay will de-energise in

the event of an alarm or a pre-alarm (inverter almost too hot, ripple on the input almost too

high, battery voltage almost too low).

VEConfigure software

With VEConfigure software the relay can also be programmed for other purposes, for example

to provide a generator starting signal.

15

EN NL FR DE ES IT Appendix

5.3 Configuration by computer

All settings can be changed by means of a computer.

Some settings can be changed with DIP switches (see Section 5.4).

For changing settings with the computer, the following is required:

- VEConfigure3 software: can be downloaded free of charge at www.victronenergy.com.

- A MK3-USB (VE.Bus to USB) interface, and a RJ45 UTP cable.

Alternatively, the Interface MK2.2b (VE.Bus to RS232) and a RJ45 UTP cable can be used.

5.4 Configuration with DIP switches

Some settings can be changed with DIP switches.

Procedure:

a) Turn the Multi on, preferably without load and without AC voltage on the input.

The Multi will then operate in inverter mode.

b) Set the DIP switches as required.

c) Store the settings by toggling DIP switch 3 one time.

16

5.4.1. DIP switch 1 to 3

These DIP switches can be used to set:

- Battery charge voltage and Absorption time

- Search mode

Ds1-ds2: Setting the charge algorithm

Ds1-ds2

Absorption

voltage

Float

voltage

Storage

Voltage

Absorption

Time

(hours)

Suitable for

Ds1=off

Ds2=off

(default)

14.4

28.8

57.6

13.8

27.6

55.2

13.2

26.4

52.8

8

Gel Victron Deep

Discharge

Gel Exide A200

AGM Victron Deep

Discharge

Ds1=on

Ds2=off

14.1

28.2

56.4

13.8

27.6

55.2

13.2

26.4

52.8

8

Gel Victron Long

Life (OPzV)

Gel Exide A600

(OPzV)

Gel MK battery

Li-ion (LiFePO4)

Ds1=off

Ds2=on

14.7

29.4

58.8

13.8

27.6

55.2

13.2

26.4

52.8

5

AGM Victron Deep

Discharge

Tubular plate or

OPzS batteries in

semi-float mode

AGM spiral cell

Ds1=on

Ds2=on

15.0

30.0

60.0

13.8

27.6

55.2

13.2

26.4

52.8

6

Tubular plate or

OPzS batteries in

cyclic mode

DS3 double function.

Ds3: Search Mode and store off = off on = on

Store the settings by toggling DIP switch 3 one time.

17

EN NL FR DE ES IT Appendix

5.4.2 Exemplary settings

Example 1 is the factory setting (since factory settings are entered by computer, all DIP

switches of a new product are set to ‘off’).

DS-1 Charge voltage

off

DS-2 Charge voltage

off

DS-3 Search mode

off

→

←

DS-1

on

DS-2

off

DS-3

off

→

←

DS-1

on

DS-2

on

DS-3

on

→

←

Example 1: (factory setting)

1, 2 GEL 14.4 V

3 Search mode off

3 Store setting: off→ on→ off

Example 2

1,2 Gel Victron Long Life

3 Search mode off

3 Store setting: off→ on→ off

Example 3

1, 2 Tubular plate 15V

3 Search mode on

3 Store setting: on→ off→ on

Store the settings by toggling DIP switch 3 one time.

The LEDs ‘charger’ and ‘alarm’ will flash to indicate acceptance of the settings.

6. MAINTENANCE

The Multi does not require specific maintenance. It will suffice to check all connections once

a year. Avoid moisture and oil/soot/vapours, and keep the device clean.

18

7. TROUBLE SHOOTING TABLE

Proceed as follows for quick detection of common faults.

DC loads must be disconnected from the batteries and the AC loads must be disconnected

from the inverter before the inverter and/or battery charger is tested.

Consult your Victron Energy dealer if the fault cannot be resolved.

Problem

Cause

Solution

The inverter fails

to operate when

switched on

The battery voltage is too high

or too low

Ensure that the battery voltage

is within the correct value.

The inverter fails

to operate

Processor in no function-mode

Disconnect mains voltage.

Switch front switch off, wait 4

seconds.

Switch front switch on.

The alarm LED

flashes

Pre-alarm alt. 1. The DC input

voltage is low

Charge the battery or check the

battery connections.

The alarm LED

flashes

Pre-alarm alt. 2. The ambient

temperature is too high

Place the inverter in a cool and

well-ventilated room, or reduce

the load.

The alarm LED

flashes

Pre-alarm alt. 3. The load on the

inverter is higher than the

nominal load

Reduce the load.

The alarm LED

flashes

Pre-alarm alt. 4. Voltage ripple

on the DC input exceeds

1.25Vrms

Check the battery cables and

terminals.

Check the battery capacity;

increase if necessary.

The alarm LED

flashes

intermittantly

Pre-alarm alt. 5. Low battery

voltage and excessive load

Charge the batteries, reduce

the load or install batteries with

a higher capacity. Use shorter

and/or thicker battery cables.

The alarm LED is

on

The inverter did cut out following

a pre-alarm

Check the table for the

appropriate course of action.

La pagina sta caricando ...

Victron energy MultiPlus 1600VA Manuale del proprietario

Victron energy MultiPlus 1600VA Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti