Intel BOXD975XBXLKR Manuale utente

Intel® Desktop Board D975XBX

Product Guide

Order Number: D31531-003

Revision History

Revision Revision History Date

-001

First version of the Intel

®

Desktop Board D975XBX Product Guide

October 2005

-002 Second version of the Intel Desktop Board D975XBX Product Guide May 2006

-003 Third version of the Intel Desktop Board D975XBX Product Guide August 2006

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation

5200 N.E. Elam Young Parkway

Hillsboro, OR 97124

1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user’s authority to

operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the

Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux appareils

numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par le ministére des

Communications du Canada.

Disclaimer

Information in this document is provided in connection with Intel

®

products. No license, express or implied, by estoppel or

otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions

of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating

to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability,

or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical,

life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time,

without notice.

Desktop Board D975XBX may contain design defects or errors known as errata which may cause the product to deviate

from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product

order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be

obtained from Intel Corporation by going to the World Wide Web site at: http://www.intel.com/ or by calling 1-800-548-4725.

Intel, Pentium, and Celeron are registered trademarks of Intel Corporation or its subsidiaries in the United States and other

countries.

* Other names and brands may be claimed as the property of others.

iii

Preface

This Product Guide gives information about board layout, component installation, BIOS updates,

and regulatory requirements for Intel

®

Desktop Board D975XBX.

Intended Audience

The Product Guide is intended only for technically qualified personnel.

Intended Uses

All Intel desktop boards are evaluated as Information Technology Equipment (I.T.E.) for use in

personal computers (PCs) for installation in homes, offices, schools, computer rooms, and similar

locations. The suitability of this product for other PC or embedded non-PC applications or other

environments, such as medical, industrial, alarm systems, test equipment, etc. may not be supported

without further evaluation by Intel.

Information Layout

The chapters in this Product Guide are arranged as follows:

•

1 Desktop Board Features: a summary of product features.

•

2 Installing and Replacing Desktop Board Components: instructions on how to install the

desktop board and other hardware components.

•

3 BIOS: information about how to update the BIOS.

•

4 Configuring for RAID (Intel

®

Matrix Storage Technology) Requires Microsoft

Windows* XP or 2000 and SATA Hard Drive(s): information about configuring your system

for RAID.

•

5 Intel® Quick Resume Technology Driver (Intel® QRTD): information about installing and

configuring Intel Quick Resume Technology.

•

A Error Messages and Indicators: information about BIOS error messages and beep codes.

•

B Regulatory Compliance: safety and EMC regulations, product certification.

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

Intel Desktop Board D975XBX Product Guide

iv

Terminology

The table below gives descriptions to some common terms used in the product guide.

Term Description

GB Gigabyte (1,073,741,824 bytes)

GHz Gigahertz (one billion hertz)

KB Kilobyte (1024 bytes)

MB Megabyte (1,048,576 bytes)

Mbit Megabit (1,048,576 bits)

MHz Megahertz (one million hertz)

Box Contents

• Intel

®

Desktop Board

• I/O shield

• One ATA-66/100 cable

• One diskette drive cable

• Four Serial ATA cables

• One rear panel USB 2.0 adapter

• One front panel USB 2.0/IEEE 1394/audio adapter

• One 2x2 to 2x4 power supply cable adapter

• Intel

®

Express Installer driver CD-ROM

• Intel Express Installer software DVD-ROM

• One diskette with the Intel

®

Matrix Storage RAID driver

• One diskette with the Silicon Image* SATA Controller RAID driver

• Back panel audio covers

• Quick Reference poster

• Integration Guide poster

• Printed Product Guide

• Configuration and battery caution statement label

v

Contents

1 Desktop Board Features

Supported Operating Systems ............................................................................................10

Desktop Board Components ...............................................................................................11

Processor............................................................................................................................13

Main Memory ......................................................................................................................13

Intel

®

975X Express Chipset ...............................................................................................14

Audio Subsystem ................................................................................................................14

Input/Output (I/O) Controller ................................................................................................15

LAN Subsystem ..................................................................................................................15

LAN Subsystem Software...........................................................................................15

RJ-45 LAN Connector LEDs.......................................................................................16

Hi-Speed USB 2.0 Support..................................................................................................16

Enhanced IDE Interface ......................................................................................................17

Serial ATA...........................................................................................................................17

Expandability.......................................................................................................................17

BIOS ...................................................................................................................................17

Serial ATA and IDE Auto Configuration ......................................................................17

PCI and PCI Express* Auto Configuration ..................................................................18

Security Passwords....................................................................................................18

Chassis Intrusion.................................................................................................................18

Power Management Features .............................................................................................18

ACPI...........................................................................................................................19

Fan Connectors..........................................................................................................19

Fan Speed Control (Intel

®

Precision Cooling Technology)..........................................19

Suspend to RAM (Instantly Available PC Technology) ...............................................19

Resume on Ring.........................................................................................................20

Wake from USB..........................................................................................................20

Wake from PS/2* Keyboard/Mouse ............................................................................20

PME# Wakeup Support ..............................................................................................20

Speaker...............................................................................................................................21

Battery.................................................................................................................................21

Real-Time Clock..................................................................................................................21

2 Installing and Replacing Desktop Board Components

Before You Begin................................................................................................................23

Installation Precautions .......................................................................................................24

Prevent Power Supply Overload.................................................................................24

Observe Safety and Regulatory Requirements...........................................................24

Installing the I/O Shield .......................................................................................................25

Installing and Removing the Desktop Board........................................................................26

Installing and Removing a Processor ..................................................................................27

Installing a Processor .................................................................................................27

Installing the Processor Fan Heat Sink.......................................................................30

Connecting the Processor Fan Heat Sink Cable.........................................................30

Removing the Processor ............................................................................................30

Intel Desktop Board D975XBX Product Guide

vi

Installing and Removing Memory ........................................................................................31

Installing DIMMs.........................................................................................................32

Removing DIMMs.......................................................................................................35

Installing and Removing a PCI Express x16 Card ...............................................................35

Installing a PCI Express x16 Card ..............................................................................36

Removing the PCI Express x16 Card .........................................................................37

Connecting the IDE Cable...................................................................................................38

Connecting the Serial ATA Cable........................................................................................39

Connecting Internal Headers...............................................................................................40

Front Panel Audio Header ..........................................................................................41

IEEE 1394a Header....................................................................................................41

USB 2.0 Headers .......................................................................................................41

Front Panel Header ....................................................................................................42

Alternate Front Panel Power LED Header ..................................................................42

Installing the Rear Panel USB 2.0 Adapter .................................................................43

Installing the Front Panel USB/IEEE 1394/Audio Adapter...........................................44

Connecting Chassis Fan Cables .........................................................................................45

Connecting Power Supply Cables .......................................................................................46

Connecting 2x10 Power Supply Cables......................................................................46

Connecting 2x12 Power Supply Cables......................................................................47

Other Connectors................................................................................................................48

Setting the BIOS Configuration Jumper...............................................................................49

Clearing Passwords ............................................................................................................50

Back Panel Connectors.......................................................................................................51

Replacing the Battery..........................................................................................................52

3 BIOS

Accessing the BIOS Setup Program....................................................................................57

Updating the BIOS ..............................................................................................................57

Updating the BIOS with the Intel

®

Express BIOS Update Utility..................................57

Updating the BIOS with the Iflash Memory Update Utility ...........................................58

4 Configuring for RAID (Intel

®

Matrix Storage Technology) Requires

Microsoft Windows* XP or 2000 and SATA Hard Drive(s)

Configuring the BIOS for Intel Matrix Storage Technology..........................................61

Creating Your RAID Set .............................................................................................61

Loading the Intel Matrix Storage Technology RAID Drivers and Software ..................61

Setting Up a “RAID Ready” System............................................................................62

5 Intel

®

Quick Resume Technology Driver (Intel

®

QRTD)

Overview.............................................................................................................................63

Installation and Configuration..............................................................................................63

A Error Messages and Indicators

BIOS Beep Codes...............................................................................................................67

BIOS Error Messages .........................................................................................................67

Contents

vii

B Regulatory Compliance

Safety Regulations ..............................................................................................................69

Place Battery Marking ................................................................................................69

European Union Declaration of Conformity Statement ........................................................70

Product Ecology Statements ...............................................................................................71

Lead-Free Desktop Board ..........................................................................................73

EMC Regulations ................................................................................................................74

Ensure Electromagnetic Compatibility (EMC) Compliance..........................................75

Product Certifications ..........................................................................................................76

Board-Level Certification Markings.............................................................................76

Chassis and Component Certifications.......................................................................77

Figures

1. Desktop Board D975XBX Components ........................................................................11

2. LAN Connector LEDs....................................................................................................16

3. Location of Standby Power Indicator.............................................................................20

4. Installing the I/O Shield.................................................................................................25

5. Location of Mounting Screw Holes................................................................................26

6. Lift Socket Lever...........................................................................................................27

7. Lift the Load Plate.........................................................................................................27

8. Remove the Protective Socket Cover ...........................................................................28

9. Remove the Processor from the Protective Processor Cover........................................28

10. Install the Processor .....................................................................................................29

11. Close the Load Plate ....................................................................................................29

12. Connecting the Processor Fan Heat Sink Cable to the Processor Fan Header.............30

13. Dual Channel Memory Configuration Example 1...........................................................31

14. Dual Channel Memory Configuration Example 2...........................................................31

15. Dual Channel Memory Configuration Example 3...........................................................32

16. Use DDR2 DIMMs ........................................................................................................33

17. Installing a DIMM ..........................................................................................................34

18. Installing PCI Express Graphics Cards .........................................................................36

19. Removing the PCI Express x16 Card............................................................................37

20. Connecting the IDE Cable ............................................................................................38

21. Connecting Serial ATA Cables......................................................................................39

22. Internal Headers ...........................................................................................................40

23. Connecting the Rear Panel USB 2.0 Adapter ...............................................................43

24. Connecting the Front Panel USB/IEEE 1394/Audio Cables ..........................................44

25. Location of Fan Headers...............................................................................................45

26. Connecting 2x10 Power Supply Cables ........................................................................46

27. Connecting 2x12 Power Supply Cables ........................................................................47

28. Location of Other Connectors .......................................................................................48

29. Location of the BIOS Configuration Jumper Block ........................................................49

30. Back Panel Connectors ................................................................................................51

31. Removing the Battery ...................................................................................................55

32. Accessing the BIOS Setup Program .............................................................................57

Intel Desktop Board D975XBX Product Guide

viii

Tables

1. Feature Summary...........................................................................................................9

2. Desktop Board D975XBX Components ........................................................................12

3. Power Supply Requirements.........................................................................................13

4. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs ..........................................16

5. Front Panel Audio Header Signal Names......................................................................41

6. IEEE 1394a Header Signal Names...............................................................................41

7. USB 2.0 Header Signal Names.....................................................................................41

8. Front Panel Header Signal Names................................................................................42

9. Jumper Settings for the BIOS Setup Program Modes ...................................................49

10. Beep Codes..................................................................................................................67

11. BIOS Error Messages...................................................................................................67

12. Safety Regulations........................................................................................................69

13. Lead-Free Board Markings ...........................................................................................73

14. EMC Regulations..........................................................................................................74

15. Product Certification Markings ......................................................................................76

9

1 Desktop Board Features

This chapter briefly describes the main features of Intel

®

Desktop Board D975XBX. Table 1

summarizes the major features of the desktop board.

Table 1. Feature Summary

Form Factor

ATX (304.80 millimeters [12.00 inches] x 243.84 millimeters [9.60 inches])

Processor

Support for an Intel

®

processor in the LGA775 package with 1066/800 MHz

front side bus

Main Memory

Four 240-pin SDRAM Dual Inline Memory Module (DIMM) sockets

667/533 MHz dual channel DDR2 SDRAM interface

Support for ECC and non-ECC memory

Designed to support up to 8 GB of system memory

Chipset

Intel

®

975X Express Chipset consisting of:

Intel

®

82975X Memory Controller Hub (MCH) with Direct Media Interface

Intel

®

82801GH I/O Controller Hub (ICH7DH) supporting Intel

®

Matrix Storage

Technology

Audio

Intel 975X Express Chipset

Intel

®

High Definition Audio codec

Up to 8-channel audio with jack sensing

Graphics Support for Multiple PCI Express* Graphics cards

Expansion

Capabilities

Two PCI bus add-in card connectors

One PCI Express x16 connector (electrical x16 or x8)

One PCI Express x16 connector (electrical x8)

One PCI Express x16 connector (electrical x4)

LAN Subsystem

Intel

®

82573V or 82573L Gigabit Ethernet LAN controller with RJ-45 connector

BIOS

Intel

®

Platform Innovation Framework for Extensible Firmware Interface

8 Mbit Serial Peripheral Interface (SPI) device

Support for SMBIOS

Intel

®

Rapid BIOS Boot

Intel

®

Express BIOS Update

RAID

Intel

®

Matrix Storage Technology for Serial ATA

Silicon Image SATALink* for Serial ATA

continued

Intel Desktop Board D975XBX Product Guide

10

Table 1. Feature Summary (continued)

Peripheral Interfaces

One front panel audio header (yellow)

Up to eight USB 2.0 ports:

⎯ Four ports routed to the back panel

⎯ Four ports routed to two USB headers

Eight Serial ATA channels (one device per channel):

— Four RAID capable Serial ATA (3.0 Gb/s) connectors (black) via the

ICH7DH

— Four RAID capable Serial ATA (1.5 Gb/s) connectors (blue) via the

discrete RAID controller

Up to two IEEE 1394 ports:

⎯ One IEEE 1394a port routed to the back panel

⎯ One IEEE 1394a header (blue)

One IDE interface with ATA-66/100 support

One diskette drive interface

One parallel port

One serial port

RJ-45 LAN port

PS/2* keyboard and mouse ports

Power Management

Support for Advanced Configuration and Power Interface (ACPI)

Suspend to RAM (STR)

Wake on USB, PCI, PCI Express, PS/2, LAN, and front panel

Hardware Management

Hardware monitor with:

⎯ Four fan sensing inputs used to monitor fan activity

⎯ Remote diode temperature sensing

⎯ Intel

®

Precision Cooling Technology fan speed control

⎯ Voltage sensing to detect out of range values

Related Links

For more information about Intel Desktop Board D975XBX, including the Technical Product

Specification (TPS), BIOS updates, and device drivers, go to:

http://support.intel.com/support/motherboards/desktop/

Supported Operating Systems

The desktop board supports the following operating systems:

• Microsoft Windows* XP Media Center Edition 2005

• Microsoft Windows XP Professional

• Microsoft Windows XP Professional x64 Edition

• Microsoft Windows XP Home

• Microsoft Windows 2000

Desktop Board Features

11

Desktop Board Components

Figure 1 shows the approximate location of the major components on Desktop Board D975XBX.

OM18176

Channel A

Channel B

Y

X

A

Z

K

L

M

DIMM 0

DIMM 1

DIMM 0

DIMM 1

JA B DC E G H IF

W U T RSV

BB

Q P O N

Coaxial Digital

Line Out

Optical Digital

Line Out

(Toslink)

Line In

RJ45

IEEE

1394

Figure 1. Desktop Board D975XBX Components

Intel Desktop Board D975XBX Product Guide

12

Table 2. Desktop Board D975XBX Components

Label Description

A Auxiliary rear chassis fan header (4-pin)

B PCI bus add-in card connector 2 (SMBus routed)

C PCI Express x16 connector 3 (electrical x4)

D PCI bus add-in card connector 1

E PCI Express x16 connector 2 (electrical x8)

F Front panel audio header

G Primary PCI Express x16 connector 1 (electrical x16 or x8)

H Rear chassis fan header (3-pin)

I Alternate power connector (1x4)

J Back panel connectors

K 12 V power connector (2x4)

L Processor socket (LGA775)

M Processor fan header (4-pin)

N Standby LED

O Main power connector (2x12)

P Diskette drive connector

Q BIOS configuration jumper

R IDE connector (right angle connector)

S Chassis intrusion header

T Battery

U 3-Gigabit/s Serial ATA connectors 0, 1, 2, and 3 (black)

V Front chassis fan header (3-pin)

W Alternate front panel power LED header (1x3)

X USB 2.0 headers (two ports per header)

Y IEEE 1394a header

Z 1.5-Gigabit/s Serial ATA connectors 4, 5, 6, and 7 (blue)

AA Front panel header

BB Speaker

Related Links

Go to the following links for more information about:

• Intel Desktop Board D975XBX

http://www.intel.com/design/motherbd

http://support.intel.com/support/motherboards/desktop

• Supported processors

http://support.intel.com/support/motherboards/desktop

• Audio software and utilities

http://www.intel.com/design/motherbd

• LAN software and drivers

http://www.intel.com/design/motherbd

Desktop Board Features

13

Processor

CAUTION

Failure to use the appropriate power supply (below) and/or not connecting the 12 V (2x4) power

connector to the desktop board may result in damage to the board or the system may not function

properly.

Table 3. Power Supply Requirements

Platform Compatibility Guide Power Supply Requirements

05B 12V2 rating of 16 A continuous and 19 A peak current for 10 ms

05A 12V2 rating of 13 A continuous and 16.5 A peak current for 10 ms

04B or 04A ATX12V (version 2.0 or greater) compliant power supply

The desktop board D975XBX supports an Intel

®

processor in the LGA775 package. Processors are

not included with the desktop board and must be purchased separately. The processor connects to

the Intel desktop board through the LGA775 socket. The supported processors list for Desktop

Board D975XBX is located on the web at:

http://support.intel.com/support/motherboards/desktop/

Related Links

Go to the following links or pages for more information about:

• Instructions on installing or upgrading the processor, page 27 in Chapter 2

• The location of the power connectors, page 46 in Chapter 2

Main Memory

NOTE

To be fully compliant with all applicable Intel

®

SDRAM memory specifications, the desktop board

should be populated with DIMMs that support the Serial Presence Detect (SPD) data structure. If

your memory modules do not support SPD, you will see a notification to this effect on the screen at

power up. The BIOS will attempt to configure the memory controller for normal operation.

The desktop board supports dual or single channel memory configurations defined below:

• Four 240-pin Double Data Rate 2 (DDR2) SDRAM Dual Inline Memory Module (DIMMs)

connectors with gold-plated contacts.

• Support for:

⎯ Unbuffered, non-registered single or double-sided DIMMs

⎯ ECC and non-ECC DDR2 667/533 MHz memory

⎯ Serial Presence Detect (SPD) memory only

⎯ Memory configuration listed below:

• Up to 2.0 GB utilizing 256 Mb technology

• Up to 4.0 GB utilizing 512 Mb or 1 Gb technology

• Up to 8.0 GB utilizing 1 Gb technology

Intel Desktop Board D975XBX Product Guide

14

Related Links

Go to the following links or pages for more information about:

• The latest list of tested memory,

http://support.intel.com/support/motherboards/desktop/

• SDRAM specifications,

http://www.intel.com/technology/memory/

• Installing memory, page 31 in Chapter 2

Intel

®

975X Express Chipset

The Intel 975X Express Chipset consists of the following devices:

• Intel 82975X Memory Controller Hub (MCH) with Direct Media Interface

• Intel 82801GH I/O Controller Hub (ICH7DH)

Related Links

Go to the following link or pages for more information about:

• Audio drivers and utilities

http://support.intel.com/support/motherboards/desktop/

• Installing the front panel audio adapter, page 44 in Chapter 2

Input/Output (I/O) Controller

The super I/O controller features the following:

• One serial port

• One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port

(EPP) support

• Serial IRQ interface compatible with serialized IRQ support for PCI systems

• PS/2-style mouse and keyboard interfaces

• Interface for one 1.2 MB, 1.44 MB, or 2.88 MB diskette drive

• Intelligent power management, including a programmable wake up event interface

• PCI power management support

LAN Subsystem

The LAN, with the Intel 82801GH I/O Controller Hub, provides a Fast PCI LAN subsystem. The

LAN subsystem provides the following functions:

• Intel 82573V or 82573L Ethernet LAN supporting 10/100/1000 Mbit/sec

• Support for RJ-45 connector with status indicator LEDs

• Configurable EEPROM that contains the MAC address

LAN Subsystem Software

For LAN software and drivers, refer to the D975XBX link on Intel’s World Wide Web site at:

http://support.intel.com/support/motherboards/desktop

Intel Desktop Board D975XBX Product Guide

16

RJ-45 LAN Connector LEDs

Two LEDs are built into the RJ-45 LAN connector located on the back panel (see Figure 2).

OM18177

AB

Figure 2. LAN Connector LEDs

Table 4 describes the LED states when the board is powered up and the 10/100/1000 Gigabit

Ethernet LAN subsystem is operating.

Table 4. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs

LED LED Color LED State Indicates

A Off LAN link is not established

Green

On LAN link is established

Blinking LAN activity is occurring

N/A Off 10 Mb/s data rate

Green On 100 Mb/s data rate

B

Yellow On 1000 Mb/s data rate

Hi-Speed USB 2.0 Support

NOTE

Computer systems that have an unshielded cable attached to a USB port might not meet FCC

Class B requirements, even if no device or a low-speed USB device is attached to the cable.

Use a shielded cable that meets the requirements for a full-speed USB device.

The desktop board supports up to eight USB 2.0 ports via ICH7; four ports routed to the back

panel and four routed to two internal USB 2.0 headers. USB 2.0 ports are backward compatible

with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds.

USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer

rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports to USB 1.1 operation. This

may be required to accommodate operating systems that do not support USB 2.0.

Desktop Board Features

17

Enhanced IDE Interface

The ICH7 IDE interface handles the exchange of information between the processor and peripheral

devices like hard disks, CD-ROM drives, and Iomega Zip* drives inside the computer. The

interface supports:

• Up to two IDE devices (such as hard drives)

• ATAPI-style devices (such as CD-ROM drives)

• Older PIO Mode devices

• Ultra DMA-33 and ATA-66/100 protocols

Serial ATA

The desktop board supports eight Serial ATA channels, connecting one device per channel in either

a RAID or a non-RAID configuration.

Expandability

The desktop board supports the following:

• One PCI Express x16 card as an electrical x16 card or two PCI Express x16 cards as electrical

x8 cards

• One PCI Express x16 card as an electrical x4 card

• Two PCI bus add-in cards

Related Links

For information about installing a PCI Express x16 card, see page 35 in Chapter 2.

BIOS

The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI and IDE

auto-configuration utilities, and the video BIOS.

See Chapter 3 on page 57 for more information about the BIOS.

Serial ATA and IDE Auto Configuration

If you connect a Serial ATA or IDE device (such as a hard drive) to your desktop board, the auto-

configuration utility in the BIOS automatically detects and configures the device for your computer.

You do not need to run the BIOS Setup program after installing a Serial ATA or IDE device. You

can override the auto-configuration options by specifying manual configuration in the BIOS Setup

program.

When booting from a Serial ATA device, the device connected to Serial ATA connector 0 is the

first boot device and the device connected to Serial ATA connector 3 is the last boot device by

default.

Intel Desktop Board D975XBX Product Guide

18

PCI and PCI Express* Auto Configuration

If you install a PCI/PCI Express add-in card in your desktop board, the PCI/PCI Express auto-

configuration utility in the BIOS automatically detects and configures the resources (IRQs, DMA

channels, and I/O space) for that add-in card. You do not need to run the BIOS Setup program after

you install a PCI/PCI Express add-in card.

Security Passwords

The BIOS includes security features that restrict whether the BIOS Setup program can be accessed

and who can boot the computer. A supervisor password and a user password can be set for the

BIOS Setup and for booting the computer, with the following restrictions:

• The supervisor password gives unrestricted access to view and change all Setup options. If

only the supervisor password is set, pressing <Enter> at the password prompt of Setup gives

the user restricted access to Setup.

• If both the supervisor and user passwords are set, you must enter either the supervisor

password or the user password to access Setup. Setup options are then available for viewing

and changing depending on whether the supervisor or user password was entered.

• Setting a user password restricts who can boot the computer. The password prompt is

displayed before the computer is booted. If only the supervisor password is set, the computer

boots without asking for a password. If both passwords are set, you can enter either password

to boot the computer.

Related Links

For more information on standby current requirements for the desktop board, go to the link below,

select the desktop board name, and then select Technical Documentation:

http://developer.intel.com/design/motherbd/

Resume on Ring

The operation of Resume on Ring can be summarized as follows:

• Resumes operation from either ACPI S1 or ACPI S3 state

• Requires only one call to access the computer

• Detects incoming call similarly for external and internal modems

• Requires modem interrupt be unmasked for correct operation

Wake from USB

NOTE

Wake from USB requires the use of a USB peripheral that supports Wake from USB.

USB bus activity wakes the computer from an ACPI S1 or S3 state.

Wake from PS/2* Keyboard/Mouse

PS/2 keyboard/mouse activity wakes the computer from an ACPI S1 or S3 state.

PME# Wakeup Support

When the PME# signal on the PCI bus is asserted, the computer wakes from an ACPI S1, S3, or

S5 state.

La pagina si sta caricando...

Intel BOXD975XBXLKR Manuale utente

Questo manuale è adatto anche per

Intel BOXD975XBXLKR Manuale utente

in altre lingue

Documenti correlati

Altri documenti