Allen-Bradley SLC 5/04 Installation Instructions Manual

Publication 1747-IN009E-MU-P - April 2007

Installation Instructions

SLC 5/03, SLC 5/04, and SLC 5/05 Modular

Processors

Catalog Numbers 1747-L531, 1747-L532, 1747-L533, 1747-L541,

1747-L542, 1747-L543, 1747-L551, 1747-L552, 1747-L553

To Use publication

Install your chassis

Installation du châssis

Installation des Chassis

Installazione dello chassis

Instalar el chasis

Instalar o chassi

1746-IN016

Install your power supply

Installation de l’alimentation

Installation des Netzteils

Installazione dell’alimentatore

Instalar la fuente de alimentación eléctrica

Instalar a fonte de energia

1746-IN004

Install your processor

Installation de processeur

Installation des Prozessors

Installazione del processore

Instalar el procesador

Instalar o processador

1747-IN009

Topic Page

English Section 3

Section en français 15

Deutscher Abschnitt 27

Sezione in Italiano 39

Sección en español 51

Seção em português 63

Allen-Bradley Automation

2 SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors

Publication 1747-IN009E-MU-P - April 2007

Installation Instructions

English Section

SLC 5/03, SLC 5/04, and SLC 5/05 Modular

Processors

Catalog Numbers 1747-L531, 1747-L532, 1747-L533

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553

Topic Page

Safety Considerations 5

Hazardous Location Considerations 5

Required Tools and Equipment 6

Install the SLC Processor 7

Apply Power to the Processor 7

Loading Your Software 8

Establish Communication to the Processor 8

Replace the Battery 9

Troubleshooting Your SLC Processor 11

Specifications 11

Communication 12

Memory Backup 13

Battery Handling, Storing, and Transporting (Cat. No. 1747-BA) 13

Additional Resources 75

Allen-Bradley Automation

4 SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors

Publication 1747-IN009E-MU-P - April 2007

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication

SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com

) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING

Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT

Identifies information that is critical for successful application and understanding of

the product.

ATTENTION

Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you to identify a hazard,

avoid a hazard, and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that surfaces may reach dangerous temperatures.

SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors 5

Publication 1747-IN009E-MU-P - April 2007

Safety Considerations

For general recommendations concerning installation safety requirements and

safety related work practices, refer to the requirements specific to your region.

• Europe: Reference the standards found in EN 60204 and your national

regulations.

• United States: refer to NFPA 70E, Electrical Safety Requirements for

Employee Workplaces.

Hazardous Location Considerations

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or

non-hazardous locations only. The following WARNING statement applies to use in

hazardous locations.

ATTENTION

Never install, remove, or wire any module while power is applied. Also, do not

expose processor modules to surfaces or other areas that may typically hold an

electrostatic charge. Electrostatic charges can alter or destroy memory.

IMPORTANT

See page 13 for information on proper battery handling, storage, and

transporting.

WARNING

EXPLOSION HAZARD

• Substitution of components may impair suitability for Class I, Division 2.

• Do not replace components or disconnect equipment unless power has

been switched off or the area is known to be non-hazardous.

• Do not connect or disconnect components unless power has been

switched off or the area is known to be non-hazardous.

• This product must be installed in an enclosure. All cables connected to the

product must remain in the enclosure or be protected by conduit or other

means.

• All wiring must comply with N.E.C. article 501-4(b).

Allen-Bradley Automation

6 SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors

Publication 1747-IN009E-MU-P - April 2007

Required Tools and Equipment

• medium blade screwdriver

• programming equipment

• appropriate network interface or cable

Cable Requirements

Network Interface Processor

SLC 5/03 SLC 5/04 SLC 5/05

1747-UIC

X

(1)

requires 1747-C13 or 1747-CP3 cable

X

(4)

requires 1747-CP3 cable

X

(4)

1747-PIC X

1747-CP3 X X X

1784-PKTX(D)

X

(2)

requires 1784-CP14 cable

X

1784-PCMK

X

(3)

requires 1784-PCM4 cable

X

(5)

requires 1784-PCM6 cable

10/100Base-T Ethernet X

SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors 7

Publication 1747-IN009E-MU-P - April 2007

Install the SLC Processor

Make sure system power is off; then insert the processor into slot 0 of the 1746

chassis.

Apply Power to the Processor

1. Energize the chassis power supply.

2. Check the chassis power supply and processor LED indicators. The power

LED indicator on the power supply should be on and the fault LED indicator

on the processor should be flashing.

See the figure on page 8 for location of the power supply and processor LED

indicators.

IMPORTANT

The SLC 500 modular processors must be inserted into the left slot (slot 0).

Inserting the processor in another slot won’t allow the processor to operate.

In addition, remove the protective wrap after installing the processor. Failure to

remove the wrap can cause the power supply to overheat.

Power

Supply

Protective Wrap

Card Guide

Processor Release

Allen-Bradley Automation

8 SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors

Publication 1747-IN009E-MU-P - April 2007

Loading Your Software

Refer to your programming software documentation.

Establish Communication to the Processor

1. Refer to the following table to establish communication between the

processor and your personal computer.

Processor Procedure

SLC 5/03 Connect the 1747-PIC interface from the processor to your personal computer serial port

or connect the 1747-UIC interface from the processor to your personal computer USB

port to the processor using the 1747-C13 or 1747-CP3 cable. You can also use a

1784-PKTX(D) or 1784-PCMK interface, or a 1747-CP3 cable from channel 0 of the

processor to the personal computer serial port.

SLC 5/04 Connect a 1747-CP3 cable from channel 0 of the processor to the personal computer

serial port or connect the 1747-UIC interface from channel 0 of the processor to your

personal computer USB port, or use a 1784-PKTX(D) or 1784-PCMK interface.

SLC 5/05 Connect a 1747-CP3 cable from channel 0 of the processor to the personal computer

serial port, or connect the 1747-UIC interface converter from channel 0 of the processor

to your personal computer USB port. For Ethernet connection, connect channel 1 of the

processor and the PC Ethernet Card to an Ethernet hub using 10/100Base-T compatible

cable.

(1)

EtherNet/IP address must first be set via BOOTP or an RS-232 connection.

POWER

RUN

FLT

BATT

FORCE

DH485

RS232

POWER

RUN

FLT

BATT

FORCE

DH+

RS232

POWER

RUN

FLT

BATT

FORCE

ENET

RS232

Power Supply and LED Indicators

Indicates the LED indicator is OFF.

Indicates the LED indicator is ON.

Indicates the LED indicator is FLASHING.

Status of LED indicator does not matter.

SLC 5/05

SLC 5/04

SLC 5/03

SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors 9

Publication 1747-IN009E-MU-P - April 2007

2. Set the communication parameters of the software to match the default

parameters of the processor.

Replace the Battery

Your SLC processor provides back-up power for RAM through a replaceable lithium

battery. This battery provides back-up for approximately 2 years. The BATT LED

indicator on the front of the processor alerts you when the battery voltage has

fallen below a threshold level.

To replace the lithium battery follow these steps.

1. Remove power from the SLC 500 power supply.

2. Remove the processor from the chassis by pressing the retainer clips at both

the top and bottom of the module and slide it out.

Channel 0 Configuration Channel 1 Configuration

SLC 5/03, 5/04, 5/05 SLC 5/03 SLC 5/04 SLC 5/05

DF1 Full-duplex:

• no handshaking

• 19.2 Kbaud

• CRC Error Check

• duplicate detect on

• no parity

DH-485:

• 19.2 Kbaud

• node address = 1

DH+:

• 57.6 Kbaud

• node address = 1

Ethernet:

BOOTP enabled

ATTENTION

Do not remove the processor from the SLC 500 chassis until all power is

removed from the SLC 500 power supply. If you remove the power supply while

power is applied, an electrical arc can occur. This could cause an explosion in

hazardous location installations.

ATTENTION

Do not expose the processor to surfaces or other areas that may typically hold

an electrostatic charge. Electrostatic charges can alter or destroy memory.

Allen-Bradley Automation

10 SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors

Publication 1747-IN009E-MU-P - April 2007

3. Unplug the battery connector.

4. Remove the battery from the retaining clips.

5. Insert a new battery into the battery retaining clips.

6. Plug the battery connector into the socket as shown above.

7. Re-insert the module into the SLC 500 chassis.

8. Restore power to the SLC 500 power supply.

9. Close the processor door.

IMPORTANT

The SLC 5/03, 5/04, and 5/05 processors have a capacitor that provides at least

30 minutes of battery back-up while the battery is disconnected. Data in RAM

is not lost if the battery is replaced within 30 minutes.

IMPORTANT

See page 13 for information on proper battery handling, storage, and

transporting.

White

Red

Battery Connector

Left Side View

Battery

SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors 11

Publication 1747-IN009E-MU-P - April 2007

Troubleshooting Your SLC Processor

Before troubleshooting your SLC 500 system, please obtain an SLC 500 Modular

Hardware Style User Manual, publication 1747-UM011. Refer to the chapter on

troubleshooting.

In addition to the SLC 500 Modular Hardware Style User Manual, publication

1747-UM011, the SLC 500 Instruction Set Reference Manual, publication

1747-RM001, contains explanations and examples for the entire instruction set as

well as for all status words and bits. It also contains explanations for all possible

fault codes found in status word S:6.

Specifications

SLC 5/03, SLC 5/04, and SLC 5/05 Processors

Attribute SLC 5/03 SLC 5/04 SLC 5/05

L531 L532 L533 L541 L542 L543 L551 L552 L553

Memory (words) 8 K 16 K 32 K 16 K 32 K 64 K 16 K 32 K 64 K

I/O capacity,

max

4096 discrete inputs/4096 discrete outputs

Local system,

max

3 chassis / 30 slots

Programming

instructions

107

Typical scan

time

(1)

The scan times are typical for a 1 K ladder logic program consisting of simple ladder logic and communication servicing.

Actual scan times depend on your program size, instructions used, and the communication protocol.

1 ms/K 0.9 ms/K

Bit execution

(XIC)

0.44 µs 0.37 µs

Programming

software

SLC 5/03s and SLC 5/04s: RSLogix 500,

SLC 5/05s: RSLogix 500

Allen-Bradley Automation

12 SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors

Publication 1747-IN009E-MU-P - April 2007

Communication

Communication options for the SLC 5/03, 5/04, and 5/05 processors are as follows:

• DH485

• RS-232 protocols (DF1 Full-duplex, DF1 Half-duplex master/slave, DF1

Radio Modem, DH-485, or ASCII)

• Data Highway Plus (A ControlLogix Gateway is required for the SLC 5/03

and SLC 5/05 processors.)

• Ethernet TCP/IP (A 1761-NET-ENI interface module is required for the SLC

5/03 and SLC 5/04 processors)

• ControlNet (via a 1747-KFC15 module)

• DeviceNet (via a 1761-NET-DNI interface module)

Specifications

Attribute Value

Power supply loading at 5V dc 500 mA for the SLC 5/03 processor

1.0 A for the SLC 5/04 and 5/05 processors

Power supply loading at 24V dc 175 mA for the SLC 5/03 processor

0 mA for the SLC 5/04 processor

(1)

SLC 5/04 Processors manufactured prior to April 2002 draw 200 mA at 24V dc. Check your label to verify your processor’s

current draw.

0 mA for the SLC 5/05 processor

Program scan hold-up time after loss of

power

20 ms...3 s (dependent on power supply loading)

Noise immunity NEMA Standard ICS 2-230

Vibration Displacement: 0.015 in., peak-to-peak at 5-57 Hz

Acceleration: 2.5 g at 57...2000 Hz

Shock, operating 30 g

Ambient temperature rating, operating 0...60 °C (32...140 °F)

Ambient temperature rating, storage -40...85 °C (-40...185 °F)

Humidity 5 to 95% without condensation

Agency certification

See http://ab.com

for declarations of

conformity, certificates, and other

certification details.

UL Listed Industrial Control Equipment

C-UL Listed Industrial Control Equipment for use in

Canada

UL Listed Industrial Control Equipment for use in

Class I, Division 2, Hazardous Locations Groups A, B,

C or D

CE compliant for all applicable directives

C-Tick marked for all applicable acts

SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors 13

Publication 1747-IN009E-MU-P - April 2007

Memory Backup

The following table shows the memory backup options for the SLC 5/03, 5/04, and

5/05 processors. Flash EPROMs (Flash Erasable Programmable Read Only Memory)

combine the versatility of EEPROMs (Electrically-Erasable Programmable Read Only

Memory) with the security of UVPROMs (UV-Erasable PROM).

Battery Handling, Storing, and Transporting (Cat. No. 1747-BA)

Handling

Storing

Store the lithium batteries in a cool, dry environment, typically 20...25 °C

(68...77 °F) and 40% to 60% relative humidity.

Transporting

One or Two Batteries - Up to two batteries can be shipped together within the

United States without restriction. Regulations governing shipment to or within other

countries may differ.

Three or More Batteries - Procedures for the transportation of three or more

batteries shipped together within the United States are specified by the Department

of Transportation (DOT) in the Code of Federal Regulations, CFR49,

“Transportation.”

An exemption to these regulations, DOT - E7052, covers the transport of certain

hazardous materials classified as flammable solids. This exemption authorizes

Memory

Backup Option

SLC 5/03 Processor

(1747-L531, 1747-L532,

1747-L533)

SLC 5/04 Processor

(1747-L541, 1747-542,

1747-543)

SLC 5/05 Processor

(1747-L551, 1747-552,

1747-553)

Flash EPROM 1747-M13

(OS302 Series C or later)

1747-M13

(OS401 Series C or later)

1747-M13

(OS501 Series C or later)

ATTENTION

Do not charge the batteries. An explosion could result or the cells could

overheat causing burns. Do not open, puncture, crush, or otherwise mutilate

the batteries. An explosion may result and/or toxic, corrosive, and flammable

liquids would be exposed.

Allen-Bradley Automation

14 SLC 5/03, SLC 5/04, and SLC 5/05 Modular Processors

Publication 1747-IN009E-MU-P - April 2007

transport of lithium batteries by motor vehicle, rail freight, cargo vessel, and

cargo-only aircraft, providing certain conditions are met. Transport by passenger

aircraft is not permitted.

Shipment of depleted batteries for disposal may be subject to specific regulation of

the countries involved or to regulations endorsed by those countries, such as the

IATA Restricted Articles Regulations of the International Air Transport Association,

Geneva, Switzerland.

For disposal, batteries must be packaged and shipped in accordance with

transportation regulations, to a proper disposal site. The U.S. Department of

Transportation authorizes shipment of “Lithium batteries for disposal” by motor

vehicle only in regulation 173.1015 of CFR 49 (effective January 5, 1983). For

additional information contact:

U.S. Department of Transportation

Research and Special Programs Administration

400 Seventh Street, S.W.

Washington, D.C. 20590

Although the Environmental Protection Agency at this time has no regulations

specific to lithium batteries, the material contained may be considered toxic,

reactive, or corrosive. The person disposing of the material is responsible for any

hazard created in doing so. State and local regulations may exist regarding the

disposal of these materials.

For a lithium battery material safety data sheet, contact the manufacturer.

IMPORTANT

Regulations for transportation of lithium batteries are periodically revised.

Refer to http://www.dot.gov

for the latest shipping information.

ATTENTION

Do not incinerate or dispose of lithium batteries in general trash collection.

Explosion or violent rupture is possible. Batteries should be collected for

disposal in a manner to prevent against short circuiting, compacting, or

destruction of case integrity and hermetic seal.

Sanyo Energy Corporation

600 Supreme Drive

Bensenville, IL 60106

USA

Tadarand U.S. Battery Division

2 Seaview Blvd.

Port Washington, NY 11050

USA

or

Publication 1747-IN009E-FR-P - Avril 2007

Notice d'installation

Section en français

Processeurs modulaires SLC 5/03, SLC 5/04

et SLC 5/05

Références 1747-L531, 1747-L532, 1747-L533

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553

Sujet Page

Consignes de sécurité 17

Environnements dangereux 17

Outils et équipement requis 18

Installation du processeur SLC 19

Mise sous tension du processeur 19

Chargement de votre logiciel 20

Etablissement de la communication avec le processeur 20

Remplacement de la pile 21

Dépannage de votre processeur SLC 23

Caractéristiques 23

Communications 24

Sauvegarde de la mémoire 25

Manipulation, stockage et transport des piles (réf. 1747-BA) 25

Additional Resources 75

Allen-Bradley Automation

16 Processeurs modulaires SLC 5/03, SLC 5/04 et SLC 5/05

Publication 1747-IN009E-FR-P - Avril 2007

Informations importantes destinées à l'utilisateur

Les équipements électroniques possèdent des caractéristiques de fonctionnement différentes de celles des

équipements électromécaniques. La publication SGI-1.1, Safety Guidelines for the Application, Installation

and Maintenance of Solid State Controls (disponible auprès de votre agence commerciale Rockwell

Automation ou en ligne sur le site http://literature.rockwellautomation.com

), décrit certaines de ces

différences. En raison de ces différences et de la diversité des utilisations des équipements électroniques,

les personnes qui en sont responsables doivent s'assurer de l'acceptabilité de chaque application.

La société Rockwell Automation, Inc. ne saurait en aucun cas être tenue pour responsable ni être redevable

des dommages indirects ou consécutifs à l'utilisation ou à l'application de cet équipement.

Les exemples et schémas contenus dans ce manuel sont présentés à titre indicatif seulement. En raison du

nombre important de variables et d'impératifs associés à chaque installation, la société Rockwell Automation,

Inc. ne saurait être tenue pour responsable ni être redevable des suites d'utilisation réelle basée sur les

exemples et schémas présentés dans ce manuel.

La société Rockwell Automation, Inc. décline également toute responsabilité en matière de propriété

intellectuelle et industrielle concernant l'utilisation des informations, circuits, équipements ou logiciels

décrits dans ce manuel.

Toute reproduction totale ou partielle du présent document sans autorisation écrite de la société Rockwell

Automation, Inc. est interdite.

Des remarques sont utilisées tout au long de ce manuel pour attirer votre attention sur les mesures

de sécurité à prendre en compte :

AVERTISSEMENT

Actions ou situations susceptibles de provoquer une explosion en environnement

dangereux et d'entraîner des blessures pouvant être mortelles, des dégâts matériels

ou des pertes financières.

IMPORTANT

Informations particulièrement importantes dans le cadre de l'utilisation du produit.

ATTENTION

Actions ou situations risquant d'entraîner des blessures pouvant être mortelles,

des dégâts matériels ou des pertes financières. Ces mises en garde vous aident

à identifier un danger, à éviter ce danger et à en discerner les conséquences.

DANGER

D'ELECTROCUTION

L'étiquette ci-contre, placée sur l’équipement ou à l’intérieur (un variateur ou un

moteur, par ex.), signale la présence éventuelle de tensions électriques dangereuses.

RISQUE DE

BRULURE

L'étiquette ci-contre, placée sur l’équipement ou à l’intérieur (un variateur ou un

moteur, par ex.) indique que certaines surfaces peuvent atteindre des

températures particulièrement élevées.

Processeurs modulaires SLC 5/03, SLC 5/04 et SLC 5/05 17

Publication 1747-IN009E-FR-P - Avril 2007

Consignes de sécurité

Pour connaître les recommandations générales relatives aux impératifs de sécurité

d'installation et de protection des postes de travail, conformez-vous à la réglementation

locale en vigueur.

• Europe : reportez-vous à la norme EN 60204 et aux réglementations nationales.

• Etats-Unis : reportez-vous à la norme NFPA 70E, Electrical Safety Requirements

for Employee Workplaces.

Environnements dangereux

Cet équipement est adapté à une utilisation en environnements de Classe I, Division 2,

Groupes A, B, C, D ou dans des environnements non dangereux. La mise en garde

suivante porte sur une utilisation en environnement dangereux.

ATTENTION

Ne jamais installer, retirer ou câbler un module sous tension. Ne pas exposer

les modules processeurs à des surfaces ou autres zones généralement

chargées en électricité statique. Les charges électrostatiques peuvent

endommager voire détruire la mémoire.

IMPORTANT

Pour de plus amples informations sur la manipulation, le stockage

et le transport des piles, reportez-vous à la page 25.

AVERTISSEMENT

DANGER D'EXPLOSION

• La substitution de composants peut rendre cet équipement impropre

à une utilisation en environnement de Classe I, Division 2.

• Ne pas remplacer de composants ou déconnecter l'équipement sans

s'être assuré que l'alimentation est coupée et que l'environnement

est classé non dangereux.

• Ne pas connecter ou déconnecter des composants sans s'être assuré

que l'alimentation est coupée et que l'environnement est classé non

dangereux.

• Ce produit doit être installé dans une armoire. Tous les câbles qui lui sont

connectés doivent rester dans l’armoire ou être protégés par un conduit ou

par d’autres moyens.

• L'ensemble du câblage doit être conforme aux normes d'électricité

en vigueur dans le pays où l'appareil est utilisé.

Allen-Bradley Automation

18 Processeurs modulaires SLC 5/03, SLC 5/04 et SLC 5/05

Publication 1747-IN009E-FR-P - Avril 2007

Outils et équipement requis

• un tournevis plat moyen ;

• un équipement de programmation ;

• un câble ou une interface réseau approprié(e).

Câbles requis

Interface réseau Processeur

SLC 5/03 SLC 5/04 SLC 5/05

1747-UIC

X

(1)

(1) câble 1747-C13 ou 1747-CP3 requis

X

(4)

(4) câble 1747-CP3 requis

X

(4)

1747-PIC X

1747-CP3 X X X

1784-PKTX(D)

X

(2)

(2) câble 1784-CP14 requis

X

1784-PCMK

X

(3)

(3) câble 1784-PCM4 requis

X

(5)

(5) câble 1784-PCM6 requis

Ethernet 10/100Base-T X

Processeurs modulaires SLC 5/03, SLC 5/04 et SLC 5/05 19

Publication 1747-IN009E-FR-P - Avril 2007

Installation du processeur SLC

Assurez-vous que le système est hors tension, puis introduisez le processeur dans

l'emplacement 0 du châssis 1746.

Mise sous tension du processeur

1. Mettez l'alimentation du châssis sous tension.

2. Vérifiez les voyants du processeur et de l'alimentation du châssis. Le voyant de

l'alimentation doit être allumé et le voyant de défaut du processeur doit clignoter.

Reportez-vous à la figure 20 pour repérer l'emplacement des voyants de

l'alimentation et du processeur.

IMPORTANT

Les processeurs modulaires SLC 500 doivent être insérés dans l'emplacement

de gauche (emplacement 0). Si vous insérez le processeur dans un autre

emplacement, il ne fonctionnera pas.

Retirez la bande de protection après avoir installé le processeur. Dans le cas

contraire, l'alimentation risque de surchauffer.

Alimentation

Bande de protection

Guide-carte

Patte de

verrouillage

du processeur

Allen-Bradley Automation

20 Processeurs modulaires SLC 5/03, SLC 5/04 et SLC 5/05

Publication 1747-IN009E-FR-P - Avril 2007

Chargement de votre logiciel

Consultez la documentation de votre logiciel de programmation.

Etablissement de la communication avec le processeur

1. Reportez-vous au tableau suivant pour établir la communication entre le

processeur et votre ordinateur.

Processeur Procédure

SLC 5/03 Raccordez l'interface 1747-PIC entre le processeur et le port série de votre l'ordinateur,

ou l'interface 1747-UIC entre le processeur et le port USB de votre ordinateur, au moyen

d'un câble 1747-C13 ou 1747-CP3. Vous pouvez également utiliser une interface

1784-PKTX(D) ou 1784-PCMK, ou un câble 1747-CP3 entre la voie 0 du processeur

et le port série de l'ordinateur.

SLC 5/04 Utilisez un câble 1747-CP3 pour raccorder la voie 0 du processeur au port série

de l'ordinateur, ou l'interface 1747-UIC pour raccorder la voie 0 du processeur au port

USB de l'ordinateur, ou encore utilisez une interface 1784-PKTX(D) ou 1784-PCMK.

SLC 5/05 Utilisez un câble 1747-CP3 pour raccorder la voie 0 du processeur au port série

de l'ordinateur, ou le convertisseur d'interface 1747-UIC pour raccorder la voie 0 du

processeur au port USB de l'ordinateur. Pour une connexion Ethernet, connectez la voie 1

du processeur et la carte Ethernet du PC à un hub Ethernet à l’aide d’un câble

compatible 10Base-T.

(1)

(1) L'adresse EtherNet/IP doit d'abord être définie via BOOTP ou une connexion RS-232.

POWER

RUN

FLT

BATT

FORCE

DH485

RS232

POWER

RUN

FLT

BATT

FORCE

DH+

RS232

POWER

RUN

FLT

BATT

FORCE

ENET

RS232

Voyants de l'alimentation et du processeur

Indique que le voyant est éteint.

Indique que le voyant est allumé.

Indique que le voyant clignote.

L'état du voyant n'a pas d'importance.

SLC 5/05

SLC 5/04

SLC 5/03

La pagina sta caricando ...

Allen-Bradley SLC 5/04 Installation Instructions Manual

Questo manuale è adatto anche per

Allen-Bradley SLC 5/04 Installation Instructions Manual

in altre lingue

Documenti correlati

Altri documenti