ProLights Jade Manuale utente

USER MANUAL

MANUALE UTENTE

JADE

HYBRID BEAM, SPOT

AND WASH FIXTURE

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.03-04/18

1

JADE

Packing content

• JADE

• Mount bracket

• Power supply cable and signal cable

• Safety rope

• User manual

TABLE OF

CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specifications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Slave Receive mode

3. 5 Operation in automatic mode

3. 6 Scenes Record mode

3. 7 Music mode

3. 8 Sensitivity microphone

3. 9 Linking

3. 10 DMX mode

3. 11 DMX configuration

3. 12 DMX addressing

3. 13 Connection of the DMX line

3. 14 Construction of the DMX termination

3. 15 DMX control

3. 16 Wireless control settings

3. 17 Fixture settings

3. 18 Lamp settings

3. 19 Display settings

3. 20 Fixture information

3. 21 Reset functions

3. 22 Special functions

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

2

3

6

7

8

9

12

13

14

15

16

17

27

28

29

32

33

2

JADE

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with

.

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modiﬁcations on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system ﬁtted with eﬃcient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualiﬁed electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the ﬁxture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inﬂammable liquids, water or metal objects enter the ﬁxture.

• Do not dismantle or modify the ﬁxture.

• All work must always be carried out by qualiﬁed technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation deﬁnitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way diﬀerent to the one described in this manual, it may suﬀer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut oﬀ power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the ﬁxture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the ﬁxture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the ﬁxture in a well ventilated place.

• Keep any inﬂammable material at a safe distance from the ﬁxture.

• The maximum temperature that can be reached on the external surface of the ﬁtting, in a thermally

steady state, is high. After power oﬀ, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eﬀectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ﬂashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

3

JADE

- 1 - INTRODUCTION

1.1 DESCRIPTION

JADE is a hybrid moving light delivering a full toolkit for designers in a single, compact ﬁxture. Harnessing

the power of the 280W discharge source with a custom optical system, it provides a punchy beam, even

wash and crisp spot - all from a single unit.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 280W S Osram Sirius HRI

• CT: 7.800K

• Luminous ﬂux: 9.826lm

• Lux: (2°) 31.390lux @5 m

• Lux: (5.5°) 2.562lux @5 m

• Source life expectancy: 2.000 h

OPTICS

• Zoom: beam: 2°-10° / spot: 5,5°-23° motorised linear zoom

• Lens diameter: 117mm

• Lens type: high-quality glass lens optics

• Additional optics: heat ﬁlter to switch from beam to spot modes

• Focus: motorised with auto-focus

COLOUR SYSTEM

• CTC: on wheel 2500 K and 3200 K + CTB

• Colour wheel: 13 dichroic ﬁlters + open

• Macros: linear, half colours, colour bounce

DYNAMIC EFFECTS

• Rotating gobos: 9 rotating gobos + open, interchangeable

• Gobo size: outer: 15,7 mm - image: 12 mm - thickness: 1,1 mm

• Fixed gobos: 14 ﬁxed gobos + open

• Circular prism: 8f with bi-directional rotation, indexing

• Linear prism: 6f with bi-directional rotation, indexing

• Frost: frost unit to soften the beam edge

BODY

• Pan angle: 630-540°

• Tilt angle: 265°

• Pan/Tilt resolution: 8 / 16 bit

• Feedback: automatic repositioning after accidental movement

• Body: aluminium structure with hi-resistance polycarbonate cover

• Body colour: black

CONTROL

• Protocols: DMX512, RDM, W-DMX

• DMX channels: 14 / 16 / 22 / 23channel

• W-DMX: included, wireless solution receiver

• RDM: RDM ready for ﬁxture remote monitor and settings

4

JADE

• Display: LCD high resolution colour display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX2) not included

• Hibernation: power safe mode when lost DMX

ELECTRONICS

• Dimmer: linear 0~100% mechanical dimmer

• Strobe / shutter: 1-25 ﬂash(s), mechanical

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -10° ~ +45°

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230V): 423W

• Power consumption (at 120V): 423W

PHYSICAL

• Cooling: forced air with low noise fan

• Sospension and ﬁxing: any position with quick-lock omega brackets

• Signal connection: Amphenol XLR 3p + 5p IN/OUT connectors

• Power connection: Neutrik powerCON TRUE1 IN connector

• IP rating: 20

• Dimensions (WxHxD): 355x619x235mm

• Weight: 17kg

Fig.1Technical drawing

355mm

13,97in

235mm

9,25in

619mm

24,37in

5

JADE

1.3 OPERATING ELEMENTS AND CONNECTIONS

1

2

B

A

3

8 10 12

9 11 13

4 7

5 6

1. MOVING HEAD

2. ROTARY ARM

3. HANDLE

4. LED INDICATOR "W-DMX"

5. MICROPHONE

6. BACKUP BATTERY

7. CONTROL PANEL with LCD display

and 5 button used to access

the control panel functions and

manage them.

8. DMX OUT ( 3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

9. DMX IN (3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

10. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

11. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

12. MAIN FUSE HOLDER: replace a

burnt-out fuse by one of the same

type only.

13. POWER IN (PowerCON TRUE

IN): for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

Fig.2

View A

View B

6

JADE

Fig.3

CLAMP

SAFETY

CABLE

OMEGA

BRACKETS

- 2 - INSTALLATION

2.1 MOUNTING

The JADE may be set up on a solid and even surface. By means of the ﬁxing facilities of the baseplate, the

unit can also be mounted upside down to a cross arm. The base plate is shown in ﬁg.3. For ﬁxing, stable

mounting clips are required. According to the ﬁgure, the bolts of the brackets are placed into the openings

provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that the unit

is ﬁrmly ﬁxed to avoid vibration and slipping while operating. The mounting place must be of suﬃcient

stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any installa-

tion, always comply scrupulously with all the regulations (particularly regarding safety) currently in force

in the country in which the ﬁxture’s being used. Always additionally secure the projector with the safety

rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum

fall of the projector will be 20 cm.

7

JADE

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the JADE is ready for operation. To switch oﬀ, dis-

connect the mains plug from the socket. For a more convenient operation it is recommended to connect

the unit to a socket which can be switched on and oﬀ via light switch.

3.2 BASIC

The JADE has a LCD display and 5 button used to access the control panel functions and manage them

(ﬁg.4).

Fig.4 - Functions of the buttons and display icons

CONNECT

LIGHT

INFORMATION

SET

PROGRAM

LEFT RIGHT UP DOWN ENTER BATTERY

Return to the top

level

Commute from

units, tens, hundred

in the menu

Increases the value

displayed or passes

to the previous item

in a menu

Decreases the value

displayed or passes

to the next item in

the menu

Confirms the

displayed value,

or activates the

displayed function,

or enters the

successive menu

Used to activate the

backup battery. It

allows to switching

display interface

without main power

Battery

8

JADE

MENU

1 Connect

ð

DMX Address

ð

Value (1-512)

Wireless DMX

ð

Value (1-512)

2 Light

ð

Turn On/Off

ð

ON/OFF

Automatic

ð

ON/OFF

DMX Control

ð

ON/OFF

Max Temperature

ð

Value (60°-130°

C)

Lamp Adjust

ð

Control

ð

Value (000-255)

Pan

ð

Value (000-255)

Pan Fine

ð

Value (000-255)

Tilt

ð

Value (000-255)

Tilt Fine

ð

Value (000-255)

Pan&Tilt Speed

ð

Value (000-255)

Pan&Tilt Fun

ð

Value (000-255)

Shutter Fun

ð

Value (000-255)

Shutter

ð

Value (000-255)

Dimmer

ð

Value (000-255)

Color1 Fun

ð

Value (000-255)

Color1

ð

Value (000-255)

Gobo1 Fun

ð

Value (000-255)

Gobo1

ð

Value (000-255)

Gobo1 Rot. Fun

ð

Value (000-255)

Gobo1 Rot.

ð

Value (000-255)

Gobo2 Fun

ð

Value (000-255)

Gobo2

ð

Value (000-255)

Prism

ð

Value (000-255)

Prism Rot.

ð

Value (000-255)

Focus Fun

ð

Value (000-255)

Focus

ð

Value (000-255)

Zoom

ð

Value (000-255)

3 Information

ð

Time Info.

Lamp Info.

Temperature

Fans Speed

Channel Value

3.3 MENU STRUCTURE

9

JADE

Error Message

Fixture Model

Software Ver.

4 Set

ð

Reset

ð

All

Pan & Tilt

Shutter

Colors

Gobos

Others

Movement

ð

Pan Reverse

ð

ON/OFF

Tilt Reverse

ð

ON/OFF

Pan Degree

ð

540/630

Encoders

ð

ON/OFF

Pan/Tilt Mode

ð

Standard/Smooth

UI Set

ð

Mic Sens.

ð

Value (00-99%)

No Signal

ð

Close/Hold/Auto/Music

Temperature C/F

ð

Celsius/Fahrenheit

Fans Mode

ð

Auto Speed/High Speed

Hibernation

ð

Not Hibernation/Min (01-99)

Backlight

ð

Always On/Min (01-99)

Flip Display

ð

ON/OFF

Display Bright

ð

Value (00-31)

Brand Show

ð

ON/OFF

Key Lock

ð

ON/OFF

Language

ð

EN/FR/SP...

Users

ð

User Mode

ð

Standard/Extended/ Basic-8bit/Basic-16bit/User

Edit User

ð

Max Channel/Control/Pan/Pan Fine/Tilt/Tilt Fine...

Calibration

ð

Password

ð

050 (insert to unlock the following settings)

Pan

ð

Value (-128-127)

Tilt

ð

Value (-128-127)

Dimmer

ð

Value (-128-127)

Color1

ð

Value (-128-127)

Gobo1

ð

Value (-128-127)

Prism

ð

Value (-128-127)

Focus

ð

Value (-128-127)

10

JADE

Fixture ID

ð

Name

ð

Fixture ID Name

RDM Mode

ð

Mode 1/Mode 2

Password

ð

050 (insert to unlock the following settings)

PID Code

ð

00001

Wireless Set

ð

DMX On Cable

ð

ON/OFF

Reset Connect

ð

ON/OFF

Reload Default

ð

Basic Reload

ð

ON/OFF

Program Reload

ð

ON/OFF

Password

ð

050 (insert to unlock the following settings)

Private Reload

ð

ON/OFF

All Reload

ð

ON/OFF

5 Program

ð

Play

ð

DMX Receive

Slave Receive

ð

Part 1 Receive/Part 2 Receive/Part 3 Receive

Sequence

ð

Alone/Master

Music

ð

Alone/Master

Select Chase

ð

Chase Part 1

ð

Chase 1 - Chase 8

Chase Part 2

ð

Chase 1 - Chase 8

Chase Part 3

ð

Chase 1 - Chase 8

Edit Chases

ð

Edit Chase 1

ð

Chase Test/ Step 1 - Step 64

Edit Chase ...

ð

Chase Test/ Step 1 - Step 64

Edit Chase 8

ð

Chase Test/ Step 1 - Step 64

Edit Scenes

ð

Edit Scenes 001

ð

Control/.../Fade Time/Scene Time/External Input

Edit Scenes ...

ð

Control/Pan/Pan Fine/Tilt/Tilt Fine...

Edit Scenes 250

ð

Control/Pan/Pan Fine/Tilt/Tilt Fine...

Scenes Record

ð

Sc XX - Sc XX

11

JADE

3.4 SLAVE RECEIVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the ﬁrst unit in line; other units will work as slave with the same eﬀect.

A Master unit can send up to 3 diﬀerent data groups to the Slave units, i.e. a Master unit can start 3 diﬀer-

ent Slave units, which run 3 diﬀerent programs. The Master unit sends the 3 program parts in a continuous

loop.

The Slave unit receives data from the Master unit according to the group which the Slave unit was as-

signed to.

For example, if a slave device is set to Receive Part 1, the Master unit Slave unit will send the automated

Chase Part 1; if set to Receive Part 2, the Chase Part 2 Slave units will receive from the Master.

To set the drive as a slave, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, and then select Play and press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, and select Slave Receive and press ENTER to

confirm.

• Press the UP/DOWN button to select the different modes of operation Part 1 Receive/Receive Part 2/Part 3

Receive, and then press the ENTER button to confirm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

Select the desired program on the master unit (described in section 3.5).

Use the DMX connectors of the JADE and an XLR cable to form a chain of units. Under certain conditions

and lengths you want to make a termination as shown on page 17.

3.5 OPERATIONS IN AUTOMATIC MODE

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Sequence and press ENTER to conﬁrm

your choice.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Alone, if the unit is not connected to other units.

• Press the ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The unit will go into automatic mode by executing the program automatically.

Select Chase

The function Select Chase lets you choose the automatic program to actually run.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Select Chase and press the ENTER button

to enter the next menu.

12

JADE

• Press the UP/DOWN button to scroll through the menu, then select Chase Part 1/Chase Part 2/Chase Part 3

and press ENTER to confirm.

• Press the UP/DOWN button to select Chase1-Chase8, and press the ENTER button to confirm.

• Press the LEFT button repeatedly to exit the menu and save changes.

Edit Chases

The function Edit Chases allows you to create automatic pre-programmed show.

The automatic programs Chase Part1/2/3 are each divided into Chase1-Chase8. Each Chase can be composed

of 1-64 step that can be configured through the following procedure:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Chases and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Chase 1 - Edit Chase 8, then press the

ENTER button to confirm.

• Press the UP/DOWN button to select the Step 01 - Step 64, and press ENTER to confirm.

• Press the UP/DOWN button to select the Scene you want to set for the Step chosen, and then press

ENTER to confirm.

• Press the LEFT button repeatedly to exit the menu and save changes.

Edit Scenes

The function Edit Scenes allows you to create individual scenes to be included in the Chase Step.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Scenes and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Scene 001 - Edit Scene 250, then press the

ENTER button to confirm.

• Press the UP/DOWN button to select the desired function you want to edit (Control, Pan, Tilt, etc..),

Then press the ENTER button to confirm.

• Press the UP/DOWN button to change the value of the function, then press the ENTER button to

confirm.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.6 SCENES RECORD MODE

JADE is equipped with a built-in DMX recorder by which you can transmit the programmed scenes from

your DMX-controller to the device. Proceed as follows to store the sequence of scenes in the unit.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Program icon, then press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Scenes Record and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to adjust the scene at the beginning and end to be inserted in the auto-

matic program, then press the ENTER button to conﬁrm.

• Press the LEFT button repeatedly to exit the menu and save changes.

When recalling scenes from the controller will automatically be transmitted to the device.

13

JADE

3.7 MUSIC MODE

In music mode, via its integrated microphone, the unit can be controlled by music with a clear rhythm in

the bass range. If the music control should not work optimally, increase the volume or reduce the distance

between the sound source and the light eﬀect unit or alternatively increase the sensitivity of the micro-

phone.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Music and press ENTER to conﬁrm.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the mobile head is connected in series to other units, and it performs the Master function;

- Alone, if the ﬁxture is not connected to other units.

• Press the ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The unit will go into music mode by executing an automatic program to the rhythm of music.

3.8 SENSITIVITY MICROPHONE

Select this function to set the value of the sensitivity of the microphone for use with a music control:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Mic Sens. and press ENTER to conﬁrm.

• Press the UP/DOWN button to adjust the level of sensitivity of the microphone, and then press the

ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.9 LINKING

Several units may be interconnected in order to control all further slave units to the same eﬀect of the

master unit.

1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the ﬁrst slave unit.

2. Connect the DMX OUT of the ﬁrst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.10 DMX MODE

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the DMX Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512).

• Press the ENTER key to conﬁrm the setting.

• Press the LEFT button repeatedly to exit the menu and save changes.

14

JADE

3.11 DMX CONFIGURATION

The JADE has 4 DMX channel conﬁgurations which can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Users and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select User Mode and press ENTER to conﬁrm

your choice.

• Use the UP/DOWN button to select the desired DMX channel conﬁguration (Standard, Extended, Basic1,

Basic 2, User), then press the ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The tables on page 17 show the mode of operation and their values DMX.

The unit is equipped with 3/5-pole XLR connections.

Edit User

The Edit User, in the same menu, allows you to create a proﬁle of personalized functions. You can change

the parameters of the various functions (Control, Pan, Tilt, etc.). Once you’ve created your custom proﬁle,

you can use it by selecting the USER mode as described above.

3.12 DMX ADDRESSING

For operation via light control unit with DMX512 protocol, is suﬃcient connect the controller to JADE. To

able to operate the JADE with a light controller, adjust the DMX start address for the ﬁrst a DMX channel.

If e. g. address 33 on the controller is provided for controlling the function of the ﬁrst DMX channel, adjust

the start address 33 on the JADE. The other functions of the light eﬀect panel are then automatically as-

signed to the following addresses. An example with the start address 33 is shown below:

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

23 33 33-55 56 79 102

DMX Address: 102DMX Address: 56DMX Address: 33 DMX Address: 79

Fig.5 - Example 23 DMX channels configuration

. . . . . . . . . . . .

DMX512 Controller

15

JADE

Fig.6

Fig.7

3.13 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty ﬁxture and controller operation.

Over long runs can be necessary to insert a DMX level matching ampliﬁer.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the ﬁrst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.14 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reﬂected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in ﬁgure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

3 pin XLR connector

16

JADE

3.15 DMX CONTROL

STD EXT BAS1 BAS2

FUNCTION DMX

Value

22 Ch 23 Ch 14 Ch 16 Ch

1 1 1 1

PAN

0~100% 000 - 255

2 2 2

PAN FINE

0~100% 000 - 255

3 3 2 3

TILT

0~100% 000 - 255

4 4 4

TILT FINE

0~100% 000 - 255

5 5 3 5

MOVEMENT SPEED

Fast to slow 000 - 255

6

MOVEMENT FUNCTION

Normal

Movement with backout

TBD

000 - 015

016 - 031

032 - 255

6 7

SHUTTER FUNCTION

Normal Shutter Functions

Pulse-effect Forward

Pulse-effect Reverse

Random strobe

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 255

7 8

SHUTTER

Normal Shutter Functions

Close

Strobe Rate (slow to fast)

Open

Pulse-effect Forward

Close

Strobe Rate (slow to fast)

Open

Pulse-effect Reverse

Close

Strobe Rate (slow to fast)

Open

Random Strobe

Close

Strobe Rate (slow to fast)

Open

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

4 6

SHUTTER

Shutter closed

No function (shutter open)

Strobe effect slow to fast

No function (shutter open)

Pulse-effect in sequences

No function (shutter open)

Random strobe eﬀect slow to fast

No function (shutter open)

000 - 031

032 - 063

064 - 095

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

8 9 5 7

DIMMER

Close to Open 000 - 255

17

JADE

STD EXT BAS1 BAS2

FUNCTION DMX

Value

22 Ch 23 Ch 14 Ch 16 Ch

9 10

COLOR FUNCTION

Indexed

Indexed With BackOut

Forward Spin

Reverse Spin

Continuous

Color Bounce

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 111

112 - 255

10 11

COLOR

Indexed & Indexed With BackOut&Color

Bounce

Position 1 (Open)

Position 2 ~ Position 28

Forward Spin

Stop to fastest

Reverse Spin

Stop to fastest

Continuous

Positioning from 0-360 degrees

000 - 008

009 - 255

000 - 255

6 8

COLOR

Indexed

Position 1 (Open)

Position 2

Position 3

Position 4

Position 5

Position 6

Position 7

Position 8

Position 9

Position 10

Position 11

Position 12

Position 13

Position 14

Indexed With Backout

Position 1 (Open)

Position 2

Position 3

Position 4

Position 5

Position 6

Position 7

Position 8

Position 9

Position 10

Position 11

Position 12

Position 13

Position 14

000 - 001

002 - 003

004 - 005

006 - 007

008 - 009

010 - 011

012 - 013

014 - 015

016 - 017

018 - 019

020 - 021

022 - 023

024 - 025

026 - 027

028 - 029

030 - 031

032 - 033

034 - 035

036 - 037

038 - 039

040 - 041

042 - 043

044 - 045

046 - 047

048 - 049

050 - 051

052 - 053

054 - 055

18

JADE

STD EXT BAS1 BAS2

FUNCTION DMX

Value

22 Ch 23 Ch 14 Ch 16 Ch

6 8

Indexed With Bounce

Position 1 (Open)

Position 2

Position 3

Position 4

Position 5

Position 6

Position 7

Position 8

Position 9

Position 10

Position 11

Position 12

Position 13

Position 14

Forward Wheel Spin

Stop to fastest

Reverse Wheel Spin

Stop to fastest

056 - 067

068 - 079

080 - 091

092 - 103

104 - 115

116 - 127

128 - 139

140 - 151

152 - 163

164 - 175

176 - 187

188 - 199

200 - 211

212 - 223

224 - 239

240 - 255

11 12

ROT GOBO FUNCTION

Indexed

Indexed with Backout

Forward Spin

Reverse Spin

Continuous

Shake

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 095

096 - 255

12 13

ROT GOBO

Indexed & Indexed With Backout&Shake

Position 1 (Open)

Position 1 (Spot Open)

Position 2

Position 3

Position 4

Position 5

Position 6

Position 7

Position 8

Position 9

Position 10

Forward Wheel Spin

Stop to fastest

Reverse Wheel Spin

Stop to fastest

Continuous

Positioning from 0-360 degrees

000 - 003

004 - 025

026 -051

052 - 077

078 -103

104 - 129

130 - 155

156 - 181

182 - 207

208 - 233

234 - 255

000 - 255

7 9

ROT GOBO

Indexed

Position 1 (Open)

Position 1 (Spot Open)

Position 2

Position 3

Position 4

Position 5

Position 6

Position 7

Position 8

Position 9

Position 10

000 - 001

002 - 004

005 - 009

010 - 014

015 - 019

020 - 024

025 - 029

030 - 034

035 - 039

040 - 044

045 - 048

La pagina sta caricando ...

ProLights Jade Manuale utente

ProLights Jade Manuale utente

in altre lingue

Documenti correlati

Altri documenti