ProLights 240W moving spot Manuale utente

USER MANUAL

MANUALE UTENTE

JETSPOT3

MOVING HEAD

EN - ITEN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.003-11/18

1

JETSPOT3

Packing content

• JETSPOT3

• Mount bracket

• User manual

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Introduction

1. 1 Description 1. 1 Description

1. 2 Technical specications1. 2 Technical specications

1. 3 Operating elements and connections1. 3 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Using the menu3. 3 Using the menu

3. 4 Menu structure3. 4 Menu structure

3. 5 Linking3. 5 Linking

3. 6 DMX address3. 6 DMX address

3. 7 DMX mode3. 7 DMX mode

3. 8 DMX addressing 3. 8 DMX addressing

3. 9 Fixture settings3. 9 Fixture settings

3. 10 Advanced 3. 10 Advanced

3. 11 Fixture information3. 11 Fixture information

3. 12 Operation in automatic mode 3. 12 Operation in automatic mode

3. 13 Automatic mode speed3. 13 Automatic mode speed

3. 14 Connection of the DMX line 3. 14 Connection of the DMX line

3. 15 Construction of the DMX termination 3. 15 Construction of the DMX termination

3. 16 DMX control3. 16 DMX control

3. 17 Colors and gobos3. 17 Colors and gobos

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement4. 2 Fuse replacement

4. 3 Trouble shooting4. 3 Trouble shooting

2

3

5

6

7

8

10

11

13

14

15

16

20

21

22

JETSPOT3

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with

.

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

3

JETSPOT3

- 1 - INTRODUCTION

1.1 DESCRIPTION

JETSPOT3 is a LED spot luminaire designed to deliver a stunning light level for its size and price. Ideal both

for installation and for rental, the JETSPOT3 focusses on maximising the light output from its LED source

to deliver a crisp, even beam from a compact size.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 240W high-power white LED

• CT: 7.500K

• CRI: 78

• Luminous ux: 12’459lm

• Lux: 13’389lx @3 m

• Lux: 1’205lx @10 m

• Source life expectancy: >30.000 h

OPTICS

• Beam angle: 20°

• Lens diameter: 74mm

• Lens type: high-quality glass lens optics

• Focus: motorised

COLOUR SYSTEM

• Colour wheel: 7 dichroic lters + open on 2 independent colour wheels (7 + 7)

DYNAMIC EFFECTS

• Rotating gobos: 7 rotating gobos + open, interchangeable, indexing

• Gobo size: outer: 27,8 mm - image: 23 mm - thickness: 3 mm

• Fixed gobos: 8 xed gobos + open, interchangeable

• Gobo size: outer: 29,6 mm - image: 23,8 mm - thickness: 0,5 mm

• Circular prism: 3f with bi-directional rotation, indexing

• Frost: linear 0 - 100% frost lter

• Iris: 5 ~ 100% motorised linear iris

• Auto mode: built-in programs with execution speed adjustment

BODY

• Pan angle: 540°

• Tilt angle: 260°

• Pan/Tilt resolution: 16 bit

• Feedback: automatic repositioning after accidental movement

• Body: aluminium structure with hi-resistance polycarbonate cover

• Body colour: black, white nishing available

CONTROL

• Protocols: DMX512, RDM

• DMX channels: 17 / 19channel

• RDM: RDM ready for xture remote monitor and settings

JETSPOT3

4

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Strobe / shutter: 0 ~ 30 Hz, electronic

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230V): 316W

• Power consumption (at 120V): 322W

• Output (at 230V): 12 units on a single power line

• Output (at 120V): 6 units on a single power line

PHYSICAL

• Cooling: forced air with low noise fan

• Sospension and xing: any position with quick-lock omega brackets

• Signal connection: Amphenol XLR 3p + 5p IN/OUT connectors

• Power connection: Neutrik powerCON IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 355x500x257mm

• Weight: 17,3kg

Fig.1

500

344

257

Technical drawing

5

JETSPOT3

Fig.2

1

2

A

B

3

4

7

8

5

6

10

119

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. MOVING HEAD

2. ROTARY ARM

3. CONTROL PANEL with TFT display

and 4 button used to access

the control panel functions and

manage them.

4. LED INDICATOR

5. DMX IN (3-pole XLR): 1 = ground, 2

= DMX -, 3 = DMX +

6. DMX OUT ( 3-pole XLR): 1 =

ground, 2 = DMX -, 3 = DMX +

7. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

8. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

9. MAIN FUSE HOLDER: replace a

burnt-out fuse by one of the same

type only.

10. POWER IN (PowerCON IN):

for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

11. POWER OUT: (PowerCON OUT) to

connect multiple units in series.

View A

View B

JETSPOT3

6

- 2 - INSTALLATION

2.1 MOUNTING

The JETSPOT3 may be set up on a solid and even surface. By means of the xing facilities of the baseplate,

the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For xing, stable

mounting clips are required. According to the gure, the bolts of the brackets are placed into the openings

provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that the unit

is rmly xed to avoid vibration and slipping while operating. The mounting place must be of sucient

stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any installa-

tion, always comply scrupulously with all the regulations (particularly regarding safety) currently in force

in the country in which the xture’s being used. Always additionally secure the projector with the safety

rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum

fall of the projector will be 20 cm.

CLAMP

SAFETY

CABLE

Fig.3

OMEGA

BRACKETS

7

JETSPOT3

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the JETSPOT3 is ready for operation. To switch

o, disconnect the mains plug from the socket. For a more convenient operation it is recommended to

connect the unit to a socket which can be switched on and o via light switch.

3.2 BASIC

The control panel of JETSPOT3 has a display and 4 buttons for the complete programming and manage-

ment of the projector menu (g.4).

Fig.4 - Functions of the buttons

UP DOWN MENU ENTER

Increases the value

displayed or passes to

the previous item in a

menu

Decreases the value

displayed or passes to

the next item in the

menu

To enter in the main

menù or to return to the

top level

Conrms the displayed

value, or activates the

displayed function, or

enters the successive

menu

Reversal of the display

To activate this function, hold simultaneously for 3 seconds UP and DOWN buttons while the display

is in the rest mode. This status will be memorised and maintained even for the next time it will be

switched on.

To return to the initial state, repeat the operation all over again.

JETSPOT3

8

3.3 USING THE MENU

1. Press the ENTER button to access the main menu.

2. Use the UP/DOWN button to select the menu to be used:

• Connect;

• Setup;

• Advanced;

• Information;

• Stand alone;

3. Press ENTER to display the rst item in the selected menu.

4. Use the UP/DOWN button to select the menu items.

NOTE - The display can be in one of two conditions: rest status and setting status. When it is in the rest sta-

tus, the display shows the projector’s DMX address. During menu setting status, after a wait time without

any key having been pressed, the display automatically returns to rest status.

It should be noted than when this condition occurs, any possible value that has been modied but not yet

conrmed with the ENTER button will be cancelled.

3.4 MENU STRUCTURE

MENU

1 CONNECT

ð

DMX Address

ð

Value (1-512)

DMX Mode

ð

Standard - 17CH

Extended - 19CH

2 SET UP

ð

Movement

ð

Pan Reverse

ð

YES/NO

Tilt Reverse

ð

YES/NO

Pan Feedback

ð

YES/NO

Tilt Feedback

ð

YES/NO

Screen

ð

Backlight

ð

ON

10s

20s

30s

Flip Display

ð

YES/NO

Warn Cue

ð

ON/OFF

Key Lock

ð

YES/NO

Fixture

ð

Fan mode

ð

Atuo/High

Temperature unit

ð

C°/F°

Auto Test

ð

Auto Test

Manual Test

ð

Pan

Pan Fine

Tilt

Tilt Fine

Pan/Tilt Speed

Dimmer

Shutter

Color1

Color2

ð

Value (000-255) for each function

9

JETSPOT3

Gobo1

R-Gobo1

Gobo2

Prism Rot

Focus

Frost

Iris

ð

Value (000-255) for each function

3 ADVANCED

ð

Reset

ð

All

ð

YES/NO

Pan

Tilt

Color1

Color2

Gobo1

Gobo2

Prism

Focus

Frost

Iris

Adjust

ð

Pan Oset

ð

Value (000-255) for each function

Tilt Oset

Color1 Oset

Color2 Oset

Gobo1 Oset

R-Gobo1 Oset

Gobo2 Oset

Prism Oset

Focus Oset

Frost Oset

Iris Oset

Factory Reload

ð

YES/NO

4 INFORMATION

ð

Fixture Time

Temperature

Fans Speed

Software Ver.

UID

5

STAND ALONE

ð

Play

ð

Master/Slave

ð

Master

Slave

Sequence

ð

Show 1

Show 2

Show 3

Show 4

JETSPOT3

10

3.5 LINKING

Several units may be interconnected in order to control all further slave units to the same eect of the

master unit.

1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.6 DMX ADDRESS

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512).

• Press the ENTER key to conrm the setting.

• Press the MENU button repeatedly to exit the menu and save changes.

3.7 DMX MODE

The JETSPOT3 has more DMX channel congurations which can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select DMX Mode and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the mode and press ENTER to conrm

your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

The unit is equipped with 3/5-pole XLR connections.

3.8 DMX ADDRESSING

For operation via light control unit with DMX512 protocol, is sucient connect the controller to JETSPOT3.

To able to operate the JETSPOT3 with a light controller, adjust the DMX start address for the rst a DMX

channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX chan-

nel, adjust the start address 33 on the JETSPOT3. The other functions of the light eect panel are then

automatically assigned to the following addresses.

An example with the start address 33 is shown below:

Speed

ð

Value (000-100%)

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

19 33 33-52 53 72 91

21 33 33-54 55 76 97

11

JETSPOT3

3.9 FIXTURE SETTINGS

You can change the parameters for the device by following these steps:

MOVEMENT

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Movement and press the ENTER but-

ton to enter the next menu.

• Use the UP/DOWN button to select the option proposed and press the ENTER button to conrm the

setting.

- Pan Reverse - Pan rotation in the opposite direction. Select NO to deactivate the function (normal set-

ting); YES to activate the function (Pan Reverse).

- Tilt Reverse - Used for reversing tilt movement. Select NO to deactivate the function (normal setting);

YES to activate the function (Tilt Reverse).

- Pan/Tilt Feedbacks - Reorganization Pan/Tilt position after rolling away. Select NO to deactivate or YES

to activate the function.

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

SCREEN

You can change the following parameters related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter

the next menu.

Fig.6 - Example 21 DMX channels conguration

DMX Address: 96DMX Address: 54DMX Address: 33 DMX Address: 75

. . . . . . . . . . . .

DMX512 Controller

JETSPOT3

12

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight

after a specied time that you can set using the arrow buttons. To have the display always on select

Always On or choose another value to turn o the display after the amount of time you choose.

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select YES to activate or NO to dis-

able this function.

- Key Lock - Lock keys. With this function, you can lock the buttons on the control panel. If this function

is activated, the keys are automatically locked. To disable or temporarily disable the key lock func-

tion, press the buttons in the following order to regain access to menu commands: UP, DOWN, UP,

DOWN, RIGHT. Select YES to activate or NO to disable.

• Press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

FIXTURE

Fans Mode - Select this function to set the fans operation mode:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, and then select Fans Mode and press ENTER

to conrm.

• Press the UP/DOWN button to select Auto Speed/High Speed, press the ENTER button to conrm your

choice.

• Press the MENU button repeatedly to exit the menu and save changes

Temperature - Select this function to set the temperature unit measurement shown on the display:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN to scroll through the menu, select the Set icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN to scroll through the menu, select UI Set, and press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select Temperature C/F and press ENTER to

conrm.

• Press the UP/DOWN button to select the unit of measure Celsius/Fahrenheit and press the ENTER but-

ton

• to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

Auto and Manual test: with this menu, you can test all functions; with auto the moving head will start an auto

test, with manual you can choose each channel/function to test.

3.10 ADVANCED

Reset Functions

You can start a preset program to restore the selected function:

• Press the ENTER button to access the main menu.

13

JETSPOT3

• Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Reset and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select the function you wish to reset be-

tween All, Pan, Tilt, Color1, Color2, Gobo1, Gobo2, Prism, Focus, Frost, Iris.

• Press the ENTER button to conrm your choice and wait for the recovery of the selected function.

Adjust

Adjusts the lamp. This function allows you to modify all the parameters of the lamp: Pan Oset, Tilt Oset,

Color1 Oset, Color2 Oset, Gobo1 Oset, R-Gobo1 Oset, Gobo2 Oset, Prism Oset, Focus Oset, Frost Oset, Iris Oset.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Adjust and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to select one of the parameters and press ENTER to edit the value (000-255)

through the UP/DOWN button.

• Press the ENTER button to conrm your choice and then press the MENU button repeatedly to exit the

menu and save changes.

Factory Reload

Select this function to reset the unit to factory settings:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Factory Reload and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to select YES or NO, then press the ENTER button to conrm.

3.11 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - Through the Fixture Time function you can display the operating time of the projector.

- Temperature - Through the Temperature function can be displayed the temperature inside the xture,

near the lamp. The temperature can be displayed in degrees Celsius or Fahrenheit.

- Fans Speed - Through the Fans Speed function you can show on display the fan speed present near the

lamp. Velocity is expressed in RPM (revolutions per minute).

- Software Version - Through Software Version function you can display the currently installed software

version.

- UID - This option shows the RDM identication number.

• Press the MENU button repeatedly to exit the menu.

RDM - With this function you can call up various submenus via RDM. This device is RDM ready. RDM stands

for “Remote Device Management” and makes remote control of devices connected to the DMX-bus possible.

JETSPOT3

14

Manual settings like adjusting the DMX starting address are no longer needed. RDM is integrated in DMX

without inuencing the connections. The RDM-data is transmitted via the standard XLR-poles 1 and 2 so new

DMX-cables are not necessary. RDM ready and conventional DMX devices can be operated in one DMX line.

If DMX splitters are used and RDM control is to be used, these splitters must support RDM.

3.12 OPERATIONS IN AUTOMATIC MODE

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Sequence and press ENTER to conrm

your choice.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Slave, if the unit is connected in series with other units and it acts as the Slave;

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

The unit will go into automatic mode by executing the program automatically.

3.13 AUTOMATIC MODE SPEED

Select this function to set the value of the speed of the internal auto-shows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play, and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Speed. and press ENTER to conrm.

• Press the UP/DOWN button to adjust the speed, and then press the ENTER button to conrm your

choice.

• Press the MENU button repeatedly to exit the menu and save changes.

15

JETSPOT3

Fig.7

Fig.8

3.14 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.15 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

3 pin XLR connector

JETSPOT3

16

3.16 DMX CONTROL

STANDARD EXTENDED

FUNCTION

DMX

Value

17 ch 19 ch

1 1 PAN 8 bit 000 - 255

2 2 PAN 16 bit 000 - 255

3 3 TILT8 bit 000 - 255

4 4 TILT 16 bit 000 - 255

5 5

MOVEMENT SPEED

Fastest to slowest 000 - 255

6 6

SHUTTER

Shutter closed

No function (shutter open)

Strobe eect slow to fast

No function (shutter open)

Pulse-eect in sequences

No function (shutter open)

Random strobe eect slow to fast

No function (shutter open)

000 - 031

032 - 063

064 - 095

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

7 7

DIMMER

Dimmer (close to open) 000 - 255

8 8

COLOR WHEEL 1

Selection

Open

Open+DARK RED

DARK RED

DARK RED + DARK BLUE

DARK BLUE

DARK BLUE + YELLOW

YELLOW

YELLOW + GREEN

GREEN

GREEN + LIGHT ORANGE

LIGHT ORANGE

LIGHT ORANGE + MAGENTA

MAGENTA

MAGENTA + UV

UV

UV+Open

Forward Spin

Stop to fast

Reverse Spin

Fast to Stop

Continuous

Positioning from OPEN to OPEN

000 - 003

004 - 007

008 - 011

012 - 015

016 - 019

020 - 023

024 - 027

028 - 031

032 - 035

036 - 039

040 - 043

044 - 047

048 - 051

052 - 055

056 - 059

060 - 063

064 - 095

096 - 127

128 - 255

9 9

COLOR WHEEL 2

Selection

Open

Open+CTO

CTO

000 - 003

004 - 007

008 - 011

17

JETSPOT3

STANDARD EXTENDED

FUNCTION

DMX

Value

17 ch 19 ch

9 9

CTO + JADE

JADE

JADE + CTB

CTB

CTB + PINK

PINK

PINK + LIGHT GREEN

LIGHT GREEN

LIGHT GREEN + DARK ORANGE

DARK ORANGE

DARK ORANGE + CYAN

CYAN

CYAN+Open

Forward Spin

Stop to fast

Reverse Spin

Fast to Stop

Continuous

Positioning from OPEN to OPEN

012 - 015

016 - 019

020 - 023

024 - 027

028 - 031

032 - 035

036 - 039

040 - 043

044 - 047

048 - 051

052 - 055

056 - 059

060 - 063

064 - 095

096 - 127

128 - 255

10

ROTATING GOBO MODE

Indexed

Forward Spin

Reverse Spin

Continuous

Shake (speed on each gobo)

TBD

000 - 015

032 - 047

048 - 063

064 - 079

080 - 095

096 - 255

11

ROTATING GOBO SELECTION

Index & Shake (shake from slow to fast)

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Forward Spin

Stop to fast

Reverse Spin

Fast to stop

Continuous

Positioning from OPEN to CYAN

000 - 031

032 - 063

064 - 095

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

000 - 255

10

ROTATING GOBO WHEEL

Indexed

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

000 - 005

006 - 010

011 - 015

016 - 020

021 - 025

JETSPOT3

18

STANDARD EXTENDED

FUNCTION

DMX

Value

17 ch 19 ch

10

Gobo 5

Gobo 6

Gobo 7

Shake

Gobo 1 (shake from slow to fast)

Gobo 2 (shake from slow to fast)

Gobo 3 (shake from slow to fast)

Gobo 4 (shake from slow to fast)

Gobo 5 (shake from slow to fast)

Gobo 6 (shake from slow to fast)

Gobo 7 (shake from slow to fast)

Forward Spin

Stop to fast

Reverse Spin

Stop to fast

026 - 030

031 - 035

036 - 040

041 - 055

056 - 070

071 - 085

086 - 100

101 - 115

116 - 130

131 - 145

146 - 200

201 - 255

11 12

GOBO ROTATION

Indexing

Gobo 1 (index rotation from 0° to 360°)

Forward Spin

Stop to fast

Stop

Reverse Spin

Fast to stop

000 - 191

192 - 221

222 - 225

226 - 255

12 13

FIXED GOBOS

Selection

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Shake

Gobo 1 (shake from slow to fast)

Gobo 2 (shake from slow to fast)

Gobo 3 (shake from slow to fast)

Gobo 4 (shake from slow to fast)

Gobo 5 (shake from slow to fast)

Gobo 6 (shake from slow to fast)

Gobo 7 (shake from slow to fast)

Gobo 8 (shake from slow to fast)

Forward Spin

Slow to fast

Reverse Spin

Fast to slow

000 - 005

006 - 009

010 - 013

014 - 017

018 - 021

022 - 025

026 - 029

030 - 033

034 - 037

038 - 051

052 - 065

066 - 079

080 - 093

094 - 107

108 - 121

122 - 135

136 - 149

150 - 202

203 - 255

La pagina sta caricando ...

ProLights 240W moving spot Manuale utente

ProLights 240W moving spot Manuale utente

in altre lingue

Documenti correlati

Altri documenti