ZAPTEC Go Next Generation EV Charging Guida d'installazione

Zaptec

Smart, small

and safe

Zaptec Go

Installation Manual

English 6

Norsk 24

Svenska 42

Dansk 60

Deutsch 78

Français 96

Italiano 114

Nederlands 132

íslenska 114

Polski 132

Português 150

ไทย 168

Spanish 186

Zaptec Go

works with

any car

No matter what you drive or where

you’re going, Zaptec Go is the surest

way to power your journey. Built on

leading edge Norwegian green tech,

we’ve created a charger, that’s as

smart on the inside as it is simple

on the outside.

6

English

Important information

Before using or maintaining this product, it is important to

read the following safety instructions. Failure to follow and

apply all the instructions and procedures covered in this quick

guide will invalidate the guarantee and cause Zaptec Charger

AS and direct partners towaive all liability and claims for

compensation.

WARNING!

!Read through the instructions carefully and familiarize yourself with the equipment

before you start using it.

!This equipment must only be installed, repaired, and maintained by qualified

personnel. Repairs must be carried out by Zaptec or a pre-approved workshop.

!All applicable local, regional, and national laws and regulations must be followed

when installing, repairing, and maintaining the product.

!Do not install or use a product which is damaged in any way. See the information

in the chapter on Support and Repairs.

!Only use approved cabling for the installation.

!Do not insert foreign objects into the Type 2 socket.

!Do not use high-pressure washers to clean the charger station.

Follow the instructions in the chapter Storage and Maintenance.

!Avoid installing the charger in a location which is exposed to direct sunlight.

!Adapters are permissible – A conversion adapter from the charger outlet must only

be used if specified and approved by the vehicle manufacturer or charger producer

!Read the guarantee at zaptec.com/guarantee or contact Zaptec support

and request a copy.

7

English

Installing Zaptec Go

Status light

Type 2 socket

Charge card

authentication (RFID)

Zaptec

QR-code for installation

and activation

Scan here for the

installation video

8

English

Included in the box

3 x Cable seals 1 x Cable clamp

1 x Zaptec Go

User Manual Installation Manual

4 x T20 2 x T20 2 x T20

A

B

C

12-18 mm

cable diameter

8-14 mm

cable diameter

9

English

1. Remove the front cover

C

2. Mount the charging station

A

Height

minimum

0,9 m

Using the built-in spirit level, make sure it’s straight and at

the appropriate height. Minimum of 0,9 m from the ground.

10

English

3. Connect the power cable

Choose between three entry options

(top, back and bottom). Punch out the hole.

Carefully pull the terminal cover downwards

to remove it. Do not pull it towards you. The

cover is much easier to remove if you gently

press on the retaining tab (through the hole

by the configuration switch) while pulling

downwards.

The Zaptec Go needs an upstream

circuit breaker and RCD Type A

1

2

3

4. Secure cable

B

Prevent the cable from being dislocated by

using the cable clamp and screws

(max torque 3 Nm).

Use the cable seals to make the installation

water resistant.

11

English

5. Electrical connection

PE N L1 L2 L3 PE N L1 L2 L3

PE L1 L2 L3 PE L1 L2

Max

6 mm2

Max 12 mm

Click!

If you are installing the charger on an IT

grid, please check zendesk.zaptec.com

Connect all wires and firmly press down

all levers as illustrated. When the wires are

safely attached, replace the terminal cover

and turn on the circuit breaker.

Ferrules are optional.

Electrical wire dimensions

12

English

6. Configure charging station

To configure the Zaptec Go

with a Zaptec account

1. Open the Zaptec app and log in with

your Zaptec account

2. From the Home, tap the symbol

3. Select the “Install product” button

4. Scan the QR code located inside

the charger

5. Set the installation details (circuit breaker

size, maximum current and phase)

6. If the settings are set correctly, tap

Finish

To configure the Zaptec Go

without a Zaptec account

1. Open the Zaptec App

2. Tap “Install a charging station”

3. Scan the QR code that is located

inside the charger

4. Set the installation details (circuit

breaker size, maximum current,

and phase)

5. If the settings are set correctly,

tap Finish

Zaptec

Before you begin, install the Zaptec App

from the App Store (iOS) or Google Play Store

(Android) and make sure the Bluetooth

on your phone is switched on.

When the Zaptec Go charger is switched on,

the status indicator will be orange.

This means it is ready to be configured.

Scan here for the

configuration video

13

English

To configure with the switch

Zaptec recommends that you use the

Zaptec App to configure the charger

whenever possible. However, you can

configure the charger without using

the app by using the switch. Note that

configuring this way will limit the

functionality of the charger:

• Circuit breaker value and available

power for charging is set to the same

value set by the switch

• It is not possible to set any phase

rotation. The default phases will be set

1-phase: L1 3-phase: L1, L2, L3 The

switch is located above the connector

terminal.

Switch configurations:

1 - 6 Amps

2 - 10 Amps

3 - 13 Amps

4 - 16 Amps

5 - 20 Amps

6 - 25 Amps

7 - 32 Amps

8 - Not in use

9 - Not in use

0 - Unconfigured or configured with App

0

5

1

2

3

4 6

7

8

9

14

English

7. Confirm status indicator

9. That’s it!

8. Mount the front cover

C

Configuration is complete when the circular

light (status indicator) changes from green

to white.

Secure and lock the front cover

(max torque 1 Nm).

If you have followed all the steps so far, then the Zaptec Go should be configured

and online. Make sure you hand over the User Manual to the owner of the charger.

!Remind the owner that they should create a Zaptec App account to activate

and connect to the Zaptec Go charger.

15

English

Load Balance = max 32A in total

to the chargers. NB: Equal value

40A 40A 40A

Circuit breaker and RCD

type A.

Must be equal in value

on installations with several Zaptec Go.

One circuit breaker and RCD

type A per Zaptec Go.

Integrated residual

current protection

RDC-DD (6mA DC)

according to IEC 62955

1 phase installation

10. Install multiple chargers

16

English

10. Install multiple chargers (continued)

Maximum total current 32A

Circuit breaker and RCD

type A.

Must be equal in value

on installations with

several Zaptec Go.

One circuit breaker

and RCD Type A per

Zaptec Go.

Phase rotation for

better load distribution

during 1 phase charging.

Integrated residual current

protection RDC-DD (6mA DC)

according to IEC 62955

40A 40A 40A

3 phase installation

3 phase for the chargers

N, L1, L2. L3 N, L3, L1. L2 N, L2, L3. L1

When rotating phases on a 3-phase installation, you must use the Zaptec app

to specify which incoming phase (L1, L2 or L3) is connected to the phase 1 terminal

on the charger. This can only be done via the Install Zaptec Go journey in the Zaptec app.

17

English

No light

Updating firmware.

This normally takes a few minutes.

Error detected. Unplug vehicle

and restart the charging station.

Charger not configured

Waiting for authorization

via Zaptec App or RFID

Charging complete or charging is waiting

for scheduled start or Eco Mode

(available in selected countries)

Charging.

The configuration is complete and the charger

is ready for the owner to start connecting and

activating it through their app.

Check charger power.

Purple

Red

Orange

Yellow

Green

Blue

White

11. Status light indicator

18

English

12. Support and repairs

If you discover an issue, please read the Troubleshooting section

before contacting Zaptec Support, or visit zaptec.com/support.

19

English

13. Troubleshooting

• Inadequate network coverage.

• 4G not activated on the charging station.

• 4G base station not supporting LTE -M.

The charging station

is not online (4G LTE-M)

Unable to connect

to Wi-Fi

Check that the SSID (network name)

and the password for the Wi-Fi are correct.

If the network is not visible, you must check

that the Wi-Fi access point uses 2.4 GHz

(5 GHz is not supported), and that it uses

channels between 1 and 11.

If the SSID is hidden, you must enter the SSID

and password manually using “Other” in the

network list.

Charging does

not start

• If the status indicator is yellow, this is

because it is waiting for authorization.

Check if authorization is enabled.

• If it is green, then check that the charger

has the correct current allocated in the

Zaptec portal*.

*Zaptec Portal is the brains behind our smart charging

infrastructure. It continuously monitors, balances,

and optimizes the load between the various charging

stations.

The charging

is slow

The limitation on the charging effect will be

governed by the weakest of the following

factors: main power grid, the circuit breaker,

charging cable, On-Board Charger (OBC), Eco

Mode (in selected countries).

• Check the standalone current setting is set

to the correct value by repeating the «Install

Zaptec Go in the Zaptec App»

• Check the installation and charger power

management settings in the Zaptec Portal.

Read more on zendesk.zaptec.com

Zaptec Charger AS collects data from the product via the network.

More information on our privacy guidelines can be found at zaptec.com/privacy.

20

English

14. Storage and Maintenance

• Wipe down the charging station

with a damp cloth.

• Check that the charging connector

is free of all foreign materials.

• Check that the charging station

has no external, physical damage.

In the case of publicly accessible

installations, an annual inspection

must be carried out by qualified

personnel in accordance with

Norwegian legislation and regulations.

In the case of publicly accessible

installations, an annual inspection

must be carried out by qualified

personnel in accordance with local

legislation and regulations.

The product must be kept in a dry room with a stable

temperature. The following periodic maintenance is recommended:

La pagina sta caricando ...

ZAPTEC Go Next Generation EV Charging Guida d'installazione

ZAPTEC Go Next Generation EV Charging Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti