Shindaiwa M262S Manuale utente

Tipo
Manuale utente
1????
OPERATOR'S MANUAL
MANUEL D'UTILISATION
BEDIENUNGSANLEITUNG
MANUALE PER L'OPERATORE
MANUAL DE INSTRUCCIONES
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
M262S
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR
SAFE OPERATION. FAILURE TO DO SO COULD RESULT IN SERIOUS IN-
JURY.
AVERTISSEMENT
LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LESRÈGLES DE
SECURITÉ.LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN
ISQUE DE BLESSURE GRAVE.
WARNUNG
LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE
FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS
RISIKO SCHWERER VERLETZUNGEN.
AVVERTENZA
LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE
IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA
DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.
ADVERTENCIA
LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICACIONES
PARA UN FUNCIONAMIENTO SEGURO. DE NO HACERLO, PODRÍA SU-
FRIR LESIONES GRAVES.
1Cover
ENGLISH
(Original instructions)
OPERATOR'S MANUAL
Multi-tool System
M262S
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE
RULES FOR SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
2
Contents
For safe use of your product............................................................................................... 3
Description.......................................................................................................................... 7
Before you start .................................................................................................................. 8
Packing list .................................................................................................................... 8
Assembly .......................................................................................................................8
Preparing the fuel ........................................................................................................ 10
Engine operation...............................................................................................................11
Starting the engine ...................................................................................................... 11
Stopping the engine..................................................................................................... 12
Maintenance and care ...................................................................................................... 13
Servicing guidelines..................................................................................................... 13
Maintenance and care ................................................................................................. 13
Storage ........................................................................................................................18
Specifications.................................................................................................................... 19
Declaration of conformity .................................................................................................. 21
3
For safe use of your product
For safe use of your product
Important information
WARNING
Please ensure that you read the operator's manual before using your product.
About your operator's manual
This manual contains necessary information about the assembly, operation, and maintenance of your product.
Please read it carefully and absorb its contents.
Always keep your manual in a place where it is readily accessible.
If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.
The units used in this manual are SI units (International System of Units). Figures in parentheses are reference val-
ues, and there may be a slight conversion error in some cases.
Failure to do so could lead to an accident or serious injury.
Intended use of this product
This product is lightweight, high-performance, petrol engined unit designed for using attachment.
Do not use this unit for any purpose other than aforementioned.
The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the
illustrations used may differ from the product itself in order to make the explanations clearer.
Please consult your dealer if anything is unclear or of concern.
Failure to do so could lead to an accident or serious injury.
Do not modify the product
You must not modify the product.
To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be
covered by the manufacturer's warranty.
Do not use the product unless it has been checked and maintained
You must not use the product unless it has been checked and maintained. Always ensure that the product is checked
and maintained on a regular basis.
Failure to do so could lead to an accident or serious injury.
Loaning or assigning your product
When loaning your product to another party, ensure that the person borrowing the product receives the operator's
manual along with it.
If you assign your product to another party, please enclose the operator's manual with the product when handing it
over.
Failure to do so could lead to an accident or serious injury.
Users of the product
The product should not be used by:
people who are tired
people who have taken alcohol
people who are on medication
people who are pregnant
people who are in poor physical condition
people who have not read the operator's manual
children
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-
erty.
Failure to observe these instructions could lead to an accident.
The ignition system of this product generates electromagnetic fields during operation. Magnetic fields can cause
pacemaker interference or pacemaker failure. To reduce health risks, we recommend that pacemaker users consult
their physician and the pacemaker manufacturer before operating this product.
4
For safe use of your product
Vibration and cold
It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning,
followed by loss of colour and numbness in the fingers. The following precautions are strongly recommended be-
cause the minimum exposure which might trigger the ailment is unknown.
Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.
Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by
not smoking.
Limit the number of hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-
held power equipment is not required.
If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, con-
sult your physician before exposing yourself further to cold and vibration.
Failure to observe these instructions could result in damage to your health.
Repetitive stress injuries
It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause sore-
ness, swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities
may put you at a high risk for developing a repetitive stress injury (RSI). To reduce the risk of RSI, do the following:
Avoid using your wrist in a bent, extended or twisted position.
Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the
repetitive movement.
Do exercises to strengthen hand and arm muscles.
See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-
nosed, the more likely permanent nerve and muscle damage can be prevented.
Failure to observe these instructions could result in damage to your health.
Proper training
Do not permit operation without proper training and protective equipment.
Be thoroughly familiar with the controls and proper use of unit.
Know how to stop the unit and shut off the engine.
Know how to unhook a harnessed unit quickly.
Never allow anyone to use the unit without proper instruction.
Failure to observe these instructions could result in damage to your health.
Wear proper clothing.
Secure hair so it is above shoulder length.
Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the
unit.
Do not wear open toed footwear, or go bare-foot or barelegged.
Failure to observe these precautions could result in damage to your sight or hearing, or lead
to a serious injury.
Wear protective gear
Always wear the following protective gear.
1. Head protection (helmet): Protects the head
2. Ear muffs or ear plugs: Protect the hearing
3. Safety goggles: Protect the eyes
4. Face shield: Protects the face
5. Safety gloves: Protect the hands from cold and vibration
6. Work clothes that fit (long sleeves, long trousers): Protect the body
7. Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes
(with toecaps): Protect the feet
8. Shin guards: Protect the legs
Failure to observe these precautions could result in damage to your sight or hearing, or
lead to a serious injury.
When necessary, please use the protective gear below.
Dust mask: Protects the breathing apparatus
Bee net: To deal with attacks by bees
WARNING
5
For safe use of your product
Warning notices
Other indicators
Symbols
Environment of use and operation
Do not use the product:
under poor weather conditions.
on steep slopes or in places which give no secure foothold and are thus slippery.
at night or in dark places with poor visibility.
When using the product on a gentle slope, work in a level, contour-like motion.
A serious injury could result if you fall or slip, or fail to operate the product correctly.
For your own health and your safe and comfortable work, operate the machine within the air temperature range of
−5
o
C to 40
o
C.
Failure to observe these instructions could result in damage to your health.
Being prepared in case of an injury
In the unlikely event of an accident or injury, please ensure that you are
prepared.
First aid kit
Towels and wipes (to stop any bleeding)
Whistle or mobile phone (for calling outside help)
If you are unable to perform first aid or call for outside help, the injury could
worsen.
Put safety first in the case of fire or smoke
If fire comes from the engine or smoke appears from any area other than the exhaust vent, first distance
yourself from the product to ensure your physical safety.
Use a shovel to throw sand or other such material on the fire to prevent it from spreading, or put it out
with a fire extinguisher.
A panicked reaction could result in the fire and other damage becoming more extensive.
WARNING
DANGER WARNING CAUTION
This symbol accompanied by the
word "DANGER" calls attentions to
an act or a condition which will lead to
serious personal injury or death of op-
erators and bystanders.
This symbol accompanied by the
word "WARNING" calls attentions to
an act or a condition which can lead to
serious personal injury or death of op-
erators and bystanders.
"CAUTION" indicates a potentially
hazardous situation which, if not
avoided, may result in minor or mod-
erate injury.
Circle and slash sym-
bol means whatever is
shown is prohibited.
NOTE IMPORTANT
This enclosed message provides tips
for use, care and maintenance of the
product.
Framed text featuring the word "IM-
PORTANT" contains important infor-
mation about the use, checking,
maintenance and storage of the prod-
uct described in this manual.
Symbol form/shape Symbol description/applica-
tion
Symbol form/shape Symbol description/applica-
tion
Carefully read the operator's
manual
Petrol and oil mixture
Wear eyes, ears and head
protection
Choke Control "Cold Start"
Position (Choke Closed)
6
For safe use of your product
Safety decal(s)
The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what
the decal means before using your product.
If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal
from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.
Wear foot protection and
gloves
Choke Control "Run" Position
(Choke Open)
Emergency stop
Beware of high-temperature
areas
Do not use the product in plac-
es with poor ventilation
Guaranteed sound power lev-
el
Beware of fire Engine start
Beware of electric shocks Purge bulb (Primer)
Symbol form/shape Symbol description/applica-
tion
Symbol form/shape Symbol description/applica-
tion
1. Safety decal (Part number X505-006800)
7
Description
Description
1. UPPER DRIVE SHAFT ASSEMBLY Includes the Rear
(Right Hand) Grip Assembly, Loop (Front, Left Hand)
Handle Assembly, Flexible Drive Cable, Drive Shaft As-
sembly Coupler and Power Head.
2. Loop-handle The Loop (front) handle must be assem-
bled to the Upper Drive Shaft assembly and positioned
for proper cutting attitude and operator comfort.
3. Ignition switch "Slide switch" mounted on top of the
throttle trigger housing, move switch forward to RUN,
backward to STOP position.
4. Throttle trigger lockout Locks throttle trigger in the
idling position until you have a proper grip with your right
hand around the handle.
5. GRIP Rear (right hand) handle.
6. Suspension point Device on which the harness can be
hooked.
7. Throttle trigger Activated by the operator's finger for
controlling the engine speed.
8. Air cleaner cover Covers air filter.
9. Fuel tank Contains fuel and fuel filter.
10. Fuel tank cap For closing the fuel tank.
11. Starter handle Pull handle to start the engine.
12. Silencer cover Cover the silencer not to make operator
touch to hot surface of silencer.
13. Spark plug
14. Type and serial number
8
Before you start
Before you start
Packing list
Assembly
Attachment shaft assembly
1. Set power head/shaft assembly on a level surface.
2. Pull locator pin (A) out, and turn anticlockwise 1/4 turn to
lockout position.
3. Remove cardboard spacer, if necessary.
The following parts are packed separately in the packing box.
When you have unpacked the box, please check the parts that it contains.
Contact your dealer if anything is missing or broken.
1. Power head with upper drive shaft assembly
2. Operator's manual
3. Loop handle bracket (barrier bar)
4. Socket wrench
5. L-wrench
6. Shoulder harness
WARNING
Read the operator's manual carefully to ensure that you assemble the product correctly.
Using a product that has been incorrectly assembled could lead to an accident or serious injury.
9
Before you start
4. Carefully fit attachment drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower
drive shaft engages into the square upper drive shaft socket.
5. Rotate locator pin (A) 1/4 turn clockwise to engage lower
shaft hole. Insure locator pin is fully engaged by twisting low-
er drive shaft. Locator pin should snap flush in coupler. Full
engagement will prevent further shaft rotation.
6. Secure lower shaft assembly to coupler by tightening clamp-
ing knob (D).
7. To disassemble, reverse assembly instructions.
Handle adjustment
1. Stand in a comfortable operating position with attachment
assembled, and position front handle for comfortable opera-
tion. Tighten handle screws.
Barrier bar assembly
1. Unscrew bottom bracket of handle, and replace with Barrier
Bar as shown. Adjust handle and secure as described
above.
NOTE
Lower bearing housing and head assembly must be in line with
the motor unit.
NOTE
Collar (A) shows minimum spacing for front handle location.
WARNING
The barrier bar must be used with brush-cutter attach-
ment.
10
Before you start
Preparing the fuel
Fuel
Recommended mixture ratio; 50: 1 (2%) for ISO-L-EGD
Standard (ISO/CD 13738), JASO FC,FD grade and shindaiwa
recommended oil.
Never use two-stroke oil intended for water-cooled engines,
motor-cycle engines.
Do not mix directly in engine fuel tank.
Fuel supply
Do not add so much fuel that it reaches the mouth of the fuel
tank (A). Keep the fuel within the prescribed level (up to the
shoulder level (B) of the fuel tank).
Tighten the fuel tank cap securely after refuelling.
DANGER
Do not fuel up while the engine is hot or in operation.
Do not smoke or hold a flame near when refuelling.
If you do so, the fuel could ignite and cause fire, leading to burns.
WARNING
Do not fill fuel tanks indoors. Always fill fuel tanks outdoors over bare ground. Do not refuel the product on the load-
ing platform of a truck, or in other such places.
Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.
Otherwise, fuel may get spewed.
Mop up any fuel that overflows or spills out due to overfilling.
Fuel spills can cause fire and burns when ignited.
After refuelling, always check that there are no leaks or discharges of fuel from the fuel pipe, fuel system grommets,
or around the fuel tank cap. If you do find fuel leaks or discharges, stop using the product immediately and contact
your dealer to have it repaired.
Any fuel leaks could cause fire.
Keep the refuelling tank in a shaded area away from fire.
Use an approved fuel container.
IMPORTANT
Fuel is a mixture of regular grade petrol and an air-cooled 2-stroke engine oil. Minimum 89 Octane unleaded petrol is recom-
mended. Do not use fuel containing methyl alcohol or more than 10 % of ethyl alcohol.
Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days.
11
Engine operation
Engine operation
Starting the engine
Starting a cold engine
(Connect the spark plug cap if the product has been in storage for
a long period of time.)
1. Placing the product on level ground, check to ensure that the
attachment does not come into contact with the surface of
the ground or any other impediment using a beam or other
such implement.
2. Move the ignition switch (A) to the Start position.
3. Make sure that the throttle trigger (D) is at the idle speed po-
sition.
4. Move the choke lever (F) to the "Cold Start" (E) position.
5. Alternately press and release the purge bulb (H) until the fuel
is sucked up into it.
6. Checking that the area around you is safe, hold the position
closest to the engine firmly as shown in the illustration, pull-
ing several times on the starter grip (I).
7. If you hear an explosion-like sound and the engine stops im-
mediately, move the choke lever to the "Run" (G) position
and continue pulling on the starter grip to start the engine.
8. If the engine does not stop, return the choke lever gently to
WARNING
Be particularly careful to observe the following precautions when starting the engine:
Move at least 3m from the place where you refuelled.
Place the product in a flat, well ventilated place.
Check that there are no fuel leaks.
Check that none of the nuts and bolts are loose.
Leave plenty of space around the product and do not allow people or animals near it.
Start the engine with the throttle trigger in the idle speed position.
Hold the product firmly to the ground when starting the engine.
Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.
Check that there are no abnormal vibrations or sounds once the engine starts. Do not use the product if there are
abnormal vibrations or sounds. Contact your dealer to have it repaired.
Accidents involving parts that fall or shatter off can cause wounds or serious injury.
The exhaust fumes from the engine contain toxic gases. Do not operate the product indoors or in other
ill ventilated places.
The exhaust fumes could cause poisoning.
Do not touch silencer, spark plug, angle transmission, and other high temperature components while
the product is running or for some time after it stops.
You could burn yourself if you touch a high temperature component.
Do not touch spark plug, spark plug wire, and other high voltage components while the product is run-
ning.
You could receive an electric shock if you touch a high voltage component while the product is running.
If the attachment rotates even though the throttle trigger is in the idle speed position when the engine is started, ad-
just the carburettor before using the product.
Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.
NOTE
Pull out the starter grip gently at first, and then more rapidly. Do not pull the starter rope out to more than 2/3 of its length.
Do not let go of the starter grip as it returns.
12
Engine operation
the "Run" position.
9. Leave the engine to warm up at idle speed for a while.
When engine is hard to start, use throttle latch (C). (Pull throt-
tle trigger fully and lower throttle latch while pressing throttle
trigger lockout (B) and release throttle trigger to activate throt-
tle latch. After engine starts, pull throttle trigger slightly to re-
lease throttle latch immediately.)
Starting a warm engine
1. Move the ignition switch (A) to the Start position.
2. Make sure that the throttle trigger (D) is at the idle speed po-
sition.
3. Check that the choke lever is in the "Run" position.
4. If no fuel is visible in the purge bulb, alternately press and re-
lease the purge bulb until the fuel is sucked up into it.
5. Checking that the area around you is safe, hold the position
closest to the engine firmly, and pull on the starter grip to
start the engine.
Stopping the engine
1. Move the throttle trigger (B) to the idle speed position and set
the engine to idling (i.e. low speed).
2. Move the ignition switch (A) to the Stop position.
3. In the event of an emergency, stop the engine immediately
using the ignition switch.
4. If the engine fails to stop, move the choke lever to the "Cold
Start" position. The engine will stall and come to a halt (an
emergency stop).
If the engine fails to stop when the ignition switch is used, have
the ignition switch checked and repaired by your dealer before
you use the product again.
5. Always disconnect the spark plug wire from the spark plug to
ensure the engine cannot be started before you work on the
unit or leave it unattended.
13
Maintenance and care
Maintenance and ca re
Servicing guidelines
Maintenance and care
Cleaning air filter
1. Close choke. Loosen air cleaner cover knob and remove air
cleaner cover (B).
2. Remove air filter (A) (air filter is located inside air cleaner
cover).
3. Brush dirt from filter or clean with compressed air from car-
burettor side.
4. Reinstall air filter with cover, after installing air filter to cover.
5. Tighten air cleaner cover knob.
WARNING
Observe the following precautions when checking and maintaining your product after use:
Turn the engine off and do not attempt to check or maintain the product until the engine has cooled.
You could burn yourself.
Remove the spark plug cap before performing checks and maintenance.
An accident could occur if the product starts unexpectedly.
IMPORTANT
Checking and maintenance requires specialist knowledge. If you are unable to check and maintain the product or deal with a
fault yourself, consult your dealer. Do not attempt to dismantle the product.
For spare parts and consumables, please use only genuine parts and designated products and components. Using parts from
other manufacturers or non-designated components may result in a malfunction.
Area Maintenance Page Before use Monthly
Air filter Clean/Replace 13
Fuel filter Inspect/Clean/Replace 14
Spark plug Inspect/Clean/Adjust/Replace 15
Carburettor Adjust/Replace and adjust 14
Cooling system Inspect/Clean 15
Silencer Inspect/Tighten 15
Silencer Clean 15 •**
Drive shaft Grease 16 •*
Starter Inspect -
Fuel system Inspect 14
Screws, bolts and nuts Inspect, Tighten/Replace -
* Or 25 hours, whichever occurs first. ** Or 100 hours, whichever occurs first.
IMPORTANT
Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance.
If you have any questions or problems, please contact your dealer.
NOTE
When reinstall air filter, fit it in the frame of the cleaner case.
14
Maintenance and care
Replacing fuel filter
1. Use a piece of metal wire or the like to pick up fuel filter (A)
through fuel tank opening.
2. Pull old filter from fuel line (B).
3. Install new fuel filter.
Carburettor adjustment
Every unit is test run at the factory and the carburettor is fine
tuned for maximum performance.
Before adjusting carburettor, clean or replace air filter, start en-
gine and run several minutes to bring it to operating temperature.
The engine must return to idle speed whenever the throttle lever
is released. Idle speed is adjustable, and must be set low enough
to permit the engine clutch to disengage the attachment.
To adjust the carburettor proceed as follow:
1. Place the unit on the ground, then start the engine, and then
allow it to idle 2-3 minutes until warm.
2. If the attachment moves when the engine is at idle, reduce
the idle speed by turning the idle adjustment screw(T) coun-
ter-clockwise.
3. Repeat the process of accelerating to full throttle and return
to idle a few times. Check that the attachment stops moving
at idle.
4. If a tachometer is available, the engine idle speed should be
final adjusted to the settings recommended in the Specifica-
tions section.
NOTE
If filter is excessive dirty or no longer fits properly, replace it.
WARNING
YOU MAY ADJUST THE IDLE SPEED ONLY by turning the idle speed adjustment screw (T).
During carburettor adjustment, the attachment may move. Pay utmost attention and care to the attachment so as not
to get injured by the moving object.
When carburettor adjustment is completed, the attachment should not move at idle speed, otherwise serious per-
sonal injury may result.
You must NOT carry out any Carburettor adjustment, other than the idle speed. All other adjustments MUST be per-
formed by an authorized service dealer, or serious personal injury may result due to malfunction of the engine.
CAUTION
When there is trouble with the carburettor, contact an authorized service dealer.
NOTE
When the carburettor cannot be adjusted properly with the idle
speed adjustment screw (T), you must contact an authorized
service dealer.
15
Maintenance and care
Cooling system maintenance
Remove dust and dirt from between fins (A).
Before each use, remove accumulated debris from bottom en-
gine intake grille located between the fuel tank and starter.
Cleaning silencer
Carbon deposits in silencer (A) will cause a drop in engine out-
put and overheating. Spark arrestor screen must be checked
periodically. Clean deposits from silencer.
Check fuel system
Check before every use.
After refuelling, make sure fuel does not leak or exude from
around fuel pipe (A), fuel grommet (B) or fuel tank cap (C).
In case of fuel leakage or exudation, there is a danger of fire.
Stop using the machine immediately and request your dealer
to inspect or replace.
Check spark plug
IMPORTANT
To maintain proper engine operating temperature, cooling air must pass freely through the cylinder fin area. This
flow of air carries combustion heat away from the engine. Overheating and engine seizure can occur when:
Air intakes are blocked, preventing cooling air from reaching the cylinder.
Dust and grass build up on the outside of the cylinder. This build-up insulates the engine and prevents the heat
from leaving.
Removal of cooling passage blockages or cleaning of cylinder fins is considered "Normal Maintenance". Any resultant failure
attributed to lack of maintenance is not warranted.
Air intake
IMPORTANT
Do not remove the silencer cover. If necessary, Please consult
your dealer.
NOTE
When remove the spark plug cap, pry it with using the socket
wrench.
16
Maintenance and care
1. Check plug gap. Correct gap is 0.6 mm to 0.7 mm.
2. Inspect electrode for wear.
3. Inspect insulator for oil or other deposits.
4. If the spark plug is dirty, clean it. Do not sandblast to clean.
Remaining sand will damage engine.
5. If the electrodes or terminals are worn, or if there are cracks
in the ceramics, replace them with new parts. (see Specifi-
cations page 19)
6. Tighten to 10 N·m - 15 N·m (100kgf·cm to 150 kgf·cm).
The spark test (for checking whether the spark plug is spark-
ing) must be carried out by your dealer.
Lubricating drive shaft
1. Loosen clamping knob (A).
2. Pull locator pin (B) and rotate 1/4 turn anticlockwise to lock-
out position.
3. Remove attachment.
4. Remove coupler (E) from upper drive shaft assembly by
loosening clamping screw (C) and removing set screw (D).
5. Remove upper flex cable (F), wipe clean, and apply a thin
coating of 15ml of grease.
6. Install cable. Make sure that the flex cable fully engages into
the clutch square drive socket.
7. Slide coupler on upper drive shaft until fully seated, and align
set screw hole in coupling with hole in upper drive shaft.
8. Install and tighten set screw (D), and tighten clamping screw
(C).
a: 0.6 - 0.7 mm
IMPORTANT
The drive shaft must be lubricated with high temperature au-
tomotive grease every 25 hours of operation, otherwise
drive shaft assembly overheating and failure can result.
17
Maintenance and care
Troubleshooting table
IMPORTANT
For spare parts and consumables, please use only genuine parts and designated products and components.
Using parts from other manufacturers or non-designated components may result in a malfunction.
Problem Diagnosis Cause Solution
The engine does
not start
1. There is no fuel in the fuel tank
2. The stop switch is in the Stop position
3. Excess fuel suction
4. Electrical fault
5. Carburettor malfunction or internal stick-
ing
6. Internal engine malfunction
1. Fuel supply
2. Move to the Start po-
sition
3. Start the engine after
servicing
4. Consult your dealer
5. Consult your dealer
6. Consult your dealer
Engine is difficult to
start, fluctuating ro-
tation
Fuel is entering the overflow
pipe
1. Fuel degradation
2. Carburettor problem
1. Replace with new fuel
2. Consult your dealer
No fuel is entering the over-
flow pipe
1. Fuel filter is clogged
2. Fuel system is clogged
3. Internal carburettor parts sticking
1. Clean or replace
2. Consult your dealer
3. Consult your dealer
The spark plug is dirty or
damp
1. Fuel degradation
2. Incorrect electrode gap
3. Carbon deposits
4. Electrical fault
1. Replace
2. Adjust or replace
3. Clean or replace
4. Consult your dealer
Engine starts but
no acceleration is
possible
1. Dirty air filter
2. Dirty fuel filter
3. Blocked fuel passage
4. Carburettor adjustment problem
5. Blocked exhaust vent or silencer vent
1. Clean or replace
2. Clean or replace
3. Consult your dealer
4. Adjust
5. Clean
The engine stops 1. Carburettor adjustment problem
2. Electrical fault
1. Adjust
2. Consult your dealer
The engine fails to
stop
1. Stop switch malfunction 1. Perform an emergen-
cy stop and consult
your dealer
Attachment rotates
when the engine is
idling
1. Carburettor adjustment problem
2. Damaged clutch spring
1. Adjust
2. Consult your dealer
Consult your dealer in the event of a problem that is not covered in the table above, or other such concerns.
Please contact your dealer in order to dispose of the product or its parts in compliance with national laws.
18
Maintenance and care
Storage
Long-term storage (30 days or more)
1. Drain the fuel tank completely outdoors over bare ground.
Do not drain fuel indoors.
2. Alternately press and release the purge bulb a number of
times to remove the fuel from the purge bulb.
3. Start the engine and run it at idle speed until it comes to a
natural stop.
4. Move the ignition switch (A) to the Stop position.
5. Once the product is sufficiently cool, wipe clean any grease,
oil, dust, dirt and other materials on the outside of the prod-
uct.
6. Perform the periodic checks prescribed in this manual.
7. Check that the screws and nuts are tightened. Tighten up
any that are loose.
8. Remove the spark plug (B) and add the appropriate quantity
(around 10 mL) of clean, new 2-stroke engine oil to the cyl-
inder via the spark plug hole.
9. Place a piece of clean cloth over the spark plug hole.
10. Pull 2 or 3 times on the starter grip to distribute the engine oil
into the cylinder.
11. Observe the piston location through the spark plug hole. Pull
the recoil starter handle slowly until the piston reaches the
top of its travel and leave it there.
12. Fit the spark plug. (Do not connect the spark plug cap (C).)
13. Wrap the engine section in a plastic bag or other covering,
and store in a dry, dust-free location out of reach of children.
Manufacturer:
YAMABIKO CORPORATION
1-7-2 Suehirocho, Ohme, Tokyo 198-8760 JAPAN
Authorized Representative in Europe:
CERTIFICATION EXPERTS B.V.
P.O. box 5047, Merwedeweg 2, 3621 LR Breukelen, The Netherlands
WARNING
Do not store in sealed locations filled with fuel gas, or close to naked flames or sparks.
You could cause a fire.
When storing the product for long periods of time (30 days or more), ensure that the following preparations for storage are carried
out.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120

Shindaiwa M262S Manuale utente

Tipo
Manuale utente