Shindaiwa M262S Manuale utente

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

MANUAL DE INSTRUCCIONES

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

ESPAÑOL

M262S

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION. FAILURE TO DO SO COULD RESULT IN SERIOUS IN-

JURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LESRÈGLES DE

SECURITÉ.LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN

ISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE

FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE

IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA

DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

ADVERTENCIA

LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICACIONES

PARA UN FUNCIONAMIENTO SEGURO. DE NO HACERLO, PODRÍA SU-

FRIR LESIONES GRAVES.

1Cover

ENGLISH

(Original instructions)

OPERATOR'S MANUAL

Multi-tool System

M262S

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Contents

For safe use of your product............................................................................................... 3

Description.......................................................................................................................... 7

Before you start .................................................................................................................. 8

Packing list .................................................................................................................... 8

Assembly .......................................................................................................................8

Preparing the fuel ........................................................................................................ 10

Engine operation...............................................................................................................11

Starting the engine ...................................................................................................... 11

Stopping the engine..................................................................................................... 12

Maintenance and care ...................................................................................................... 13

Servicing guidelines..................................................................................................... 13

Maintenance and care ................................................................................................. 13

Storage ........................................................................................................................18

Specifications.................................................................................................................... 19

Declaration of conformity .................................................................................................. 21

3

For safe use of your product

Important information

WARNING

Please ensure that you read the operator's manual before using your product.

About your operator's manual

 This manual contains necessary information about the assembly, operation, and maintenance of your product.

Please read it carefully and absorb its contents.

 Always keep your manual in a place where it is readily accessible.

 If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.

 The units used in this manual are SI units (International System of Units). Figures in parentheses are reference val-

ues, and there may be a slight conversion error in some cases.

Failure to do so could lead to an accident or serious injury.

Intended use of this product

 This product is lightweight, high-performance, petrol engined unit designed for using attachment.

 Do not use this unit for any purpose other than aforementioned.

 The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

 Please consult your dealer if anything is unclear or of concern.

Failure to do so could lead to an accident or serious injury.

Do not modify the product

 You must not modify the product.

To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be

covered by the manufacturer's warranty.

Do not use the product unless it has been checked and maintained

 You must not use the product unless it has been checked and maintained. Always ensure that the product is checked

and maintained on a regular basis.

Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product

 When loaning your product to another party, ensure that the person borrowing the product receives the operator's

manual along with it.

 If you assign your product to another party, please enclose the operator's manual with the product when handing it

over.

Failure to do so could lead to an accident or serious injury.

Users of the product

 The product should not be used by:

 people who are tired

 people who have taken alcohol

 people who are on medication

 people who are pregnant

 people who are in poor physical condition

 people who have not read the operator's manual

 children

 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.

Failure to observe these instructions could lead to an accident.

 The ignition system of this product generates electromagnetic fields during operation. Magnetic fields can cause

pacemaker interference or pacemaker failure. To reduce health risks, we recommend that pacemaker users consult

their physician and the pacemaker manufacturer before operating this product.

4

For safe use of your product

Vibration and cold

 It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning,

followed by loss of colour and numbness in the fingers. The following precautions are strongly recommended be-

cause the minimum exposure which might trigger the ailment is unknown.

 Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.

 Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by

not smoking.

 Limit the number of hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-

held power equipment is not required.

 If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, con-

sult your physician before exposing yourself further to cold and vibration.

Failure to observe these instructions could result in damage to your health.

Repetitive stress injuries

 It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause sore-

ness, swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities

may put you at a high risk for developing a repetitive stress injury (RSI). To reduce the risk of RSI, do the following:

 Avoid using your wrist in a bent, extended or twisted position.

 Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the

repetitive movement.

 Do exercises to strengthen hand and arm muscles.

 See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-

nosed, the more likely permanent nerve and muscle damage can be prevented.

Failure to observe these instructions could result in damage to your health.

Proper training

 Do not permit operation without proper training and protective equipment.

 Be thoroughly familiar with the controls and proper use of unit.

 Know how to stop the unit and shut off the engine.

 Know how to unhook a harnessed unit quickly.

 Never allow anyone to use the unit without proper instruction.

Failure to observe these instructions could result in damage to your health.

Wear proper clothing.

 Secure hair so it is above shoulder length.

 Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the

unit.

 Do not wear open toed footwear, or go bare-foot or barelegged.

Failure to observe these precautions could result in damage to your sight or hearing, or lead

to a serious injury.

Wear protective gear

 Always wear the following protective gear.

1. Head protection (helmet): Protects the head

2. Ear muffs or ear plugs: Protect the hearing

3. Safety goggles: Protect the eyes

4. Face shield: Protects the face

5. Safety gloves: Protect the hands from cold and vibration

6. Work clothes that fit (long sleeves, long trousers): Protect the body

7. Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes

(with toecaps): Protect the feet

8. Shin guards: Protect the legs

Failure to observe these precautions could result in damage to your sight or hearing, or

lead to a serious injury.

 When necessary, please use the protective gear below.

 Dust mask: Protects the breathing apparatus

 Bee net: To deal with attacks by bees

WARNING

5

For safe use of your product

Warning notices

Other indicators

Symbols

Environment of use and operation

 Do not use the product:

 under poor weather conditions.

 on steep slopes or in places which give no secure foothold and are thus slippery.

 at night or in dark places with poor visibility.

 When using the product on a gentle slope, work in a level, contour-like motion.

A serious injury could result if you fall or slip, or fail to operate the product correctly.

 For your own health and your safe and comfortable work, operate the machine within the air temperature range of

−5

o

C to 40

o

C.

Failure to observe these instructions could result in damage to your health.

Being prepared in case of an injury

 In the unlikely event of an accident or injury, please ensure that you are

prepared.

 First aid kit

 Towels and wipes (to stop any bleeding)

 Whistle or mobile phone (for calling outside help)

If you are unable to perform first aid or call for outside help, the injury could

worsen.

Put safety first in the case of fire or smoke

 If fire comes from the engine or smoke appears from any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safety.

 Use a shovel to throw sand or other such material on the fire to prevent it from spreading, or put it out

with a fire extinguisher.

A panicked reaction could result in the fire and other damage becoming more extensive.

WARNING

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual

Petrol and oil mixture

Wear eyes, ears and head

protection

Choke Control "Cold Start"

Position (Choke Closed)

6

For safe use of your product

Safety decal(s)

 The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

 If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

Wear foot protection and

gloves

Choke Control "Run" Position

(Choke Open)

Emergency stop

Beware of high-temperature

areas

Do not use the product in plac-

es with poor ventilation

Guaranteed sound power lev-

el

Beware of fire Engine start

Beware of electric shocks Purge bulb (Primer)

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

1. Safety decal (Part number X505-006800)

7

Description

1. UPPER DRIVE SHAFT ASSEMBLY Includes the Rear

(Right Hand) Grip Assembly, Loop (Front, Left Hand)

Handle Assembly, Flexible Drive Cable, Drive Shaft As-

sembly Coupler and Power Head.

2. Loop-handle The Loop (front) handle must be assem-

bled to the Upper Drive Shaft assembly and positioned

for proper cutting attitude and operator comfort.

3. Ignition switch "Slide switch" mounted on top of the

throttle trigger housing, move switch forward to RUN,

backward to STOP position.

4. Throttle trigger lockout Locks throttle trigger in the

idling position until you have a proper grip with your right

hand around the handle.

5. GRIP Rear (right hand) handle.

6. Suspension point Device on which the harness can be

hooked.

7. Throttle trigger Activated by the operator's finger for

controlling the engine speed.

8. Air cleaner cover Covers air filter.

9. Fuel tank Contains fuel and fuel filter.

10. Fuel tank cap For closing the fuel tank.

11. Starter handle Pull handle to start the engine.

12. Silencer cover Cover the silencer not to make operator

touch to hot surface of silencer.

13. Spark plug

14. Type and serial number

8

Before you start

Packing list

Assembly

Attachment shaft assembly

1. Set power head/shaft assembly on a level surface.

2. Pull locator pin (A) out, and turn anticlockwise 1/4 turn to

lockout position.

3. Remove cardboard spacer, if necessary.

 The following parts are packed separately in the packing box.

 When you have unpacked the box, please check the parts that it contains.

 Contact your dealer if anything is missing or broken.

1. Power head with upper drive shaft assembly

2. Operator's manual

3. Loop handle bracket (barrier bar)

4. Socket wrench

5. L-wrench

6. Shoulder harness

WARNING

 Read the operator's manual carefully to ensure that you assemble the product correctly.

Using a product that has been incorrectly assembled could lead to an accident or serious injury.

9

Before you start

4. Carefully fit attachment drive shaft assembly into coupler (B)

to decal assembly line (C), making sure that the inner lower

drive shaft engages into the square upper drive shaft socket.

5. Rotate locator pin (A) 1/4 turn clockwise to engage lower

shaft hole. Insure locator pin is fully engaged by twisting low-

er drive shaft. Locator pin should snap flush in coupler. Full

engagement will prevent further shaft rotation.

6. Secure lower shaft assembly to coupler by tightening clamp-

ing knob (D).

7. To disassemble, reverse assembly instructions.

Handle adjustment

1. Stand in a comfortable operating position with attachment

assembled, and position front handle for comfortable opera-

tion. Tighten handle screws.

Barrier bar assembly

1. Unscrew bottom bracket of handle, and replace with Barrier

Bar as shown. Adjust handle and secure as described

above.

NOTE

Lower bearing housing and head assembly must be in line with

the motor unit.

NOTE

Collar (A) shows minimum spacing for front handle location.

WARNING

 The barrier bar must be used with brush-cutter attach-

ment.

10

Before you start

Preparing the fuel

Fuel

 Recommended mixture ratio; 50: 1 (2%) for ISO-L-EGD

Standard (ISO/CD 13738), JASO FC,FD grade and shindaiwa

recommended oil.

 Never use two-stroke oil intended for water-cooled engines,

motor-cycle engines.

 Do not mix directly in engine fuel tank.

Fuel supply

 Do not add so much fuel that it reaches the mouth of the fuel

tank (A). Keep the fuel within the prescribed level (up to the

shoulder level (B) of the fuel tank).

 Tighten the fuel tank cap securely after refuelling.

DANGER

 Do not fuel up while the engine is hot or in operation.

 Do not smoke or hold a flame near when refuelling.

If you do so, the fuel could ignite and cause fire, leading to burns.

WARNING

 Do not fill fuel tanks indoors. Always fill fuel tanks outdoors over bare ground. Do not refuel the product on the load-

ing platform of a truck, or in other such places.

 Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

Otherwise, fuel may get spewed.

 Mop up any fuel that overflows or spills out due to overfilling.

Fuel spills can cause fire and burns when ignited.

 After refuelling, always check that there are no leaks or discharges of fuel from the fuel pipe, fuel system grommets,

or around the fuel tank cap. If you do find fuel leaks or discharges, stop using the product immediately and contact

your dealer to have it repaired.

Any fuel leaks could cause fire.

 Keep the refuelling tank in a shaded area away from fire.

 Use an approved fuel container.

IMPORTANT

 Fuel is a mixture of regular grade petrol and an air-cooled 2-stroke engine oil. Minimum 89 Octane unleaded petrol is recom-

mended. Do not use fuel containing methyl alcohol or more than 10 % of ethyl alcohol.

 Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days.

11

Engine operation

Starting the engine

Starting a cold engine

(Connect the spark plug cap if the product has been in storage for

a long period of time.)

1. Placing the product on level ground, check to ensure that the

attachment does not come into contact with the surface of

the ground or any other impediment using a beam or other

such implement.

2. Move the ignition switch (A) to the Start position.

3. Make sure that the throttle trigger (D) is at the idle speed po-

sition.

4. Move the choke lever (F) to the "Cold Start" (E) position.

5. Alternately press and release the purge bulb (H) until the fuel

is sucked up into it.

6. Checking that the area around you is safe, hold the position

closest to the engine firmly as shown in the illustration, pull-

ing several times on the starter grip (I).

7. If you hear an explosion-like sound and the engine stops im-

mediately, move the choke lever to the "Run" (G) position

and continue pulling on the starter grip to start the engine.

8. If the engine does not stop, return the choke lever gently to

WARNING

Be particularly careful to observe the following precautions when starting the engine:

 Move at least 3m from the place where you refuelled.

 Place the product in a flat, well ventilated place.

 Check that there are no fuel leaks.

 Check that none of the nuts and bolts are loose.

 Leave plenty of space around the product and do not allow people or animals near it.

 Start the engine with the throttle trigger in the idle speed position.

 Hold the product firmly to the ground when starting the engine.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

 Check that there are no abnormal vibrations or sounds once the engine starts. Do not use the product if there are

abnormal vibrations or sounds. Contact your dealer to have it repaired.

Accidents involving parts that fall or shatter off can cause wounds or serious injury.

 The exhaust fumes from the engine contain toxic gases. Do not operate the product indoors or in other

ill ventilated places.

The exhaust fumes could cause poisoning.

 Do not touch silencer, spark plug, angle transmission, and other high temperature components while

the product is running or for some time after it stops.

You could burn yourself if you touch a high temperature component.

 Do not touch spark plug, spark plug wire, and other high voltage components while the product is run-

ning.

You could receive an electric shock if you touch a high voltage component while the product is running.

 If the attachment rotates even though the throttle trigger is in the idle speed position when the engine is started, ad-

just the carburettor before using the product.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

NOTE

 Pull out the starter grip gently at first, and then more rapidly. Do not pull the starter rope out to more than 2/3 of its length.

 Do not let go of the starter grip as it returns.

12

Engine operation

the "Run" position.

9. Leave the engine to warm up at idle speed for a while.

∗ When engine is hard to start, use throttle latch (C). (Pull throt-

tle trigger fully and lower throttle latch while pressing throttle

trigger lockout (B) and release throttle trigger to activate throt-

tle latch. After engine starts, pull throttle trigger slightly to re-

lease throttle latch immediately.)

Starting a warm engine

1. Move the ignition switch (A) to the Start position.

2. Make sure that the throttle trigger (D) is at the idle speed po-

sition.

3. Check that the choke lever is in the "Run" position.

4. If no fuel is visible in the purge bulb, alternately press and re-

lease the purge bulb until the fuel is sucked up into it.

5. Checking that the area around you is safe, hold the position

closest to the engine firmly, and pull on the starter grip to

start the engine.

Stopping the engine

1. Move the throttle trigger (B) to the idle speed position and set

the engine to idling (i.e. low speed).

2. Move the ignition switch (A) to the Stop position.

3. In the event of an emergency, stop the engine immediately

using the ignition switch.

4. If the engine fails to stop, move the choke lever to the "Cold

Start" position. The engine will stall and come to a halt (an

emergency stop).

∗ If the engine fails to stop when the ignition switch is used, have

the ignition switch checked and repaired by your dealer before

you use the product again.

5. Always disconnect the spark plug wire from the spark plug to

ensure the engine cannot be started before you work on the

unit or leave it unattended.

13

Maintenance and care

Maintenance and ca re

Servicing guidelines

Maintenance and care

Cleaning air filter

1. Close choke. Loosen air cleaner cover knob and remove air

cleaner cover (B).

2. Remove air filter (A) (air filter is located inside air cleaner

cover).

3. Brush dirt from filter or clean with compressed air from car-

burettor side.

4. Reinstall air filter with cover, after installing air filter to cover.

5. Tighten air cleaner cover knob.

WARNING

Observe the following precautions when checking and maintaining your product after use:

 Turn the engine off and do not attempt to check or maintain the product until the engine has cooled.

You could burn yourself.

 Remove the spark plug cap before performing checks and maintenance.

An accident could occur if the product starts unexpectedly.

IMPORTANT

 Checking and maintenance requires specialist knowledge. If you are unable to check and maintain the product or deal with a

fault yourself, consult your dealer. Do not attempt to dismantle the product.

 For spare parts and consumables, please use only genuine parts and designated products and components. Using parts from

other manufacturers or non-designated components may result in a malfunction.

Area Maintenance Page Before use Monthly

Air filter Clean/Replace 13 •

Fuel filter Inspect/Clean/Replace 14 •

Spark plug Inspect/Clean/Adjust/Replace 15 •

Carburettor Adjust/Replace and adjust 14 •

Cooling system Inspect/Clean 15 •

Silencer Inspect/Tighten 15 •

Silencer Clean 15 •**

Drive shaft Grease 16 •*

Starter Inspect - •

Fuel system Inspect 14 •

Screws, bolts and nuts Inspect, Tighten/Replace - •

* Or 25 hours, whichever occurs first. ** Or 100 hours, whichever occurs first.

IMPORTANT

 Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance.

If you have any questions or problems, please contact your dealer.

NOTE

 When reinstall air filter, fit it in the frame of the cleaner case.

14

Maintenance and care

Replacing fuel filter

1. Use a piece of metal wire or the like to pick up fuel filter (A)

through fuel tank opening.

2. Pull old filter from fuel line (B).

3. Install new fuel filter.

Carburettor adjustment

Every unit is test run at the factory and the carburettor is fine

tuned for maximum performance.

Before adjusting carburettor, clean or replace air filter, start en-

gine and run several minutes to bring it to operating temperature.

The engine must return to idle speed whenever the throttle lever

is released. Idle speed is adjustable, and must be set low enough

to permit the engine clutch to disengage the attachment.

To adjust the carburettor proceed as follow:

1. Place the unit on the ground, then start the engine, and then

allow it to idle 2-3 minutes until warm.

2. If the attachment moves when the engine is at idle, reduce

the idle speed by turning the idle adjustment screw(T) coun-

ter-clockwise.

3. Repeat the process of accelerating to full throttle and return

to idle a few times. Check that the attachment stops moving

at idle.

4. If a tachometer is available, the engine idle speed should be

final adjusted to the settings recommended in the Specifica-

tions section.

NOTE

 If filter is excessive dirty or no longer fits properly, replace it.

WARNING

 YOU MAY ADJUST THE IDLE SPEED ONLY by turning the idle speed adjustment screw (T).

 During carburettor adjustment, the attachment may move. Pay utmost attention and care to the attachment so as not

to get injured by the moving object.

 When carburettor adjustment is completed, the attachment should not move at idle speed, otherwise serious per-

sonal injury may result.

 You must NOT carry out any Carburettor adjustment, other than the idle speed. All other adjustments MUST be per-

formed by an authorized service dealer, or serious personal injury may result due to malfunction of the engine.

CAUTION

 When there is trouble with the carburettor, contact an authorized service dealer.

NOTE

When the carburettor cannot be adjusted properly with the idle

speed adjustment screw (T), you must contact an authorized

service dealer.

15

Maintenance and care

Cooling system maintenance

 Remove dust and dirt from between fins (A).

 Before each use, remove accumulated debris from bottom en-

gine intake grille located between the fuel tank and starter.

Cleaning silencer

 Carbon deposits in silencer (A) will cause a drop in engine out-

put and overheating. Spark arrestor screen must be checked

periodically. Clean deposits from silencer.

Check fuel system

 Check before every use.

 After refuelling, make sure fuel does not leak or exude from

around fuel pipe (A), fuel grommet (B) or fuel tank cap (C).

 In case of fuel leakage or exudation, there is a danger of fire.

Stop using the machine immediately and request your dealer

to inspect or replace.

Check spark plug

IMPORTANT

 To maintain proper engine operating temperature, cooling air must pass freely through the cylinder fin area. This

flow of air carries combustion heat away from the engine. Overheating and engine seizure can occur when:

 Air intakes are blocked, preventing cooling air from reaching the cylinder.

 Dust and grass build up on the outside of the cylinder. This build-up insulates the engine and prevents the heat

from leaving.

Removal of cooling passage blockages or cleaning of cylinder fins is considered "Normal Maintenance". Any resultant failure

attributed to lack of maintenance is not warranted.

Air intake

IMPORTANT

Do not remove the silencer cover. If necessary, Please consult

your dealer.

NOTE

When remove the spark plug cap, pry it with using the socket

wrench.

16

Maintenance and care

1. Check plug gap. Correct gap is 0.6 mm to 0.7 mm.

2. Inspect electrode for wear.

3. Inspect insulator for oil or other deposits.

4. If the spark plug is dirty, clean it. Do not sandblast to clean.

Remaining sand will damage engine.

5. If the electrodes or terminals are worn, or if there are cracks

in the ceramics, replace them with new parts. (see Specifi-

cations page 19)

6. Tighten to 10 N·m - 15 N·m (100kgf·cm to 150 kgf·cm).

∗ The spark test (for checking whether the spark plug is spark-

ing) must be carried out by your dealer.

Lubricating drive shaft

1. Loosen clamping knob (A).

2. Pull locator pin (B) and rotate 1/4 turn anticlockwise to lock-

out position.

3. Remove attachment.

4. Remove coupler (E) from upper drive shaft assembly by

loosening clamping screw (C) and removing set screw (D).

5. Remove upper flex cable (F), wipe clean, and apply a thin

coating of 15ml of grease.

6. Install cable. Make sure that the flex cable fully engages into

the clutch square drive socket.

7. Slide coupler on upper drive shaft until fully seated, and align

set screw hole in coupling with hole in upper drive shaft.

8. Install and tighten set screw (D), and tighten clamping screw

(C).

a: 0.6 - 0.7 mm

IMPORTANT

 The drive shaft must be lubricated with high temperature au-

tomotive grease every 25 hours of operation, otherwise

drive shaft assembly overheating and failure can result.

17

Maintenance and care

Troubleshooting table

IMPORTANT

 For spare parts and consumables, please use only genuine parts and designated products and components.

Using parts from other manufacturers or non-designated components may result in a malfunction.

Problem Diagnosis Cause Solution

The engine does

not start

1. There is no fuel in the fuel tank

2. The stop switch is in the Stop position

3. Excess fuel suction

4. Electrical fault

5. Carburettor malfunction or internal stick-

ing

6. Internal engine malfunction

1. Fuel supply

2. Move to the Start po-

sition

3. Start the engine after

servicing

4. Consult your dealer

5. Consult your dealer

6. Consult your dealer

Engine is difficult to

start, fluctuating ro-

tation

Fuel is entering the overflow

pipe

1. Fuel degradation

2. Carburettor problem

1. Replace with new fuel

2. Consult your dealer

No fuel is entering the over-

flow pipe

1. Fuel filter is clogged

2. Fuel system is clogged

3. Internal carburettor parts sticking

1. Clean or replace

2. Consult your dealer

3. Consult your dealer

The spark plug is dirty or

damp

1. Fuel degradation

2. Incorrect electrode gap

3. Carbon deposits

4. Electrical fault

1. Replace

2. Adjust or replace

3. Clean or replace

4. Consult your dealer

Engine starts but

no acceleration is

possible

1. Dirty air filter

2. Dirty fuel filter

3. Blocked fuel passage

4. Carburettor adjustment problem

5. Blocked exhaust vent or silencer vent

1. Clean or replace

2. Clean or replace

3. Consult your dealer

4. Adjust

5. Clean

The engine stops 1. Carburettor adjustment problem

2. Electrical fault

1. Adjust

2. Consult your dealer

The engine fails to

stop

1. Stop switch malfunction 1. Perform an emergen-

cy stop and consult

your dealer

Attachment rotates

when the engine is

idling

1. Carburettor adjustment problem

2. Damaged clutch spring

1. Adjust

2. Consult your dealer

 Consult your dealer in the event of a problem that is not covered in the table above, or other such concerns.

 Please contact your dealer in order to dispose of the product or its parts in compliance with national laws.

18

Maintenance and care

Storage

Long-term storage (30 days or more)

1. Drain the fuel tank completely outdoors over bare ground.

Do not drain fuel indoors.

2. Alternately press and release the purge bulb a number of

times to remove the fuel from the purge bulb.

3. Start the engine and run it at idle speed until it comes to a

natural stop.

4. Move the ignition switch (A) to the Stop position.

5. Once the product is sufficiently cool, wipe clean any grease,

oil, dust, dirt and other materials on the outside of the prod-

uct.

6. Perform the periodic checks prescribed in this manual.

7. Check that the screws and nuts are tightened. Tighten up

any that are loose.

8. Remove the spark plug (B) and add the appropriate quantity

(around 10 mL) of clean, new 2-stroke engine oil to the cyl-

inder via the spark plug hole.

9. Place a piece of clean cloth over the spark plug hole.

10. Pull 2 or 3 times on the starter grip to distribute the engine oil

into the cylinder.

11. Observe the piston location through the spark plug hole. Pull

the recoil starter handle slowly until the piston reaches the

top of its travel and leave it there.

12. Fit the spark plug. (Do not connect the spark plug cap (C).)

13. Wrap the engine section in a plastic bag or other covering,

and store in a dry, dust-free location out of reach of children.

Manufacturer:

YAMABIKO CORPORATION

1-7-2 Suehirocho, Ohme, Tokyo 198-8760 JAPAN

Authorized Representative in Europe:

CERTIFICATION EXPERTS B.V.

P.O. box 5047, Merwedeweg 2, 3621 LR Breukelen, The Netherlands

WARNING

 Do not store in sealed locations filled with fuel gas, or close to naked flames or sparks.

You could cause a fire.

When storing the product for long periods of time (30 days or more), ensure that the following preparations for storage are carried

out.

La pagina sta caricando ...

Shindaiwa M262S Manuale utente

Shindaiwa M262S Manuale utente

in altre lingue

Documenti correlati

Altri documenti