Eneo ITB-7SF0019M0A Quick Installation Manual

Quick Installation Guide

Thermal Network Camera,

336x256, 25Hz, Audio,

Composite, PoE, IP67

ITB-7SF0075M0A

ITB-7SF0013M0A

ITB-7SF0019M0A

ITB-7SF0035M0A

EN

DE

FR

IT

2

Table of content

Parts supplied ...............................................................................................................5

Part names

.....................................................................................................................6

Installation instructions ...............................................................................................7

Pan & Tilt adjustments .....................................................................................................................................................8

Power supply connections

.......................................................................................................................................... 10

Quick Network Setup ..................................................................................................11

Web viewer description .............................................................................................................................................. 12

Player control & Display

......................................................................................................................................... 12

Video Stream

............................................................................................................................................................... 13

Protocol ......................................................................................................................................................................... 13

PTZ Control

.................................................................................................................................................................. 13

User Manual

............................................................................................................................................................... 13

Setup Menu Table

..................................................................................................................................................... 14

Quick Setup .................................................................................................................16

Information ...................................................................................................................................................................... 16

Users

................................................................................................................................................................................... 16

Add

................................................................................................................................................................................ 17

Edit

.................................................................................................................................................................................. 17

Delete ............................................................................................................................................................................ 18

Date & Time

..................................................................................................................................................................... 18

Current Time

............................................................................................................................................................... 18

New Time...................................................................................................................................................................... 18

Time Zone .................................................................................................................................................................... 18

Day & Time Display ................................................................................................................................................... 19

Network

............................................................................................................................................................................. 19

IPv4 Address

............................................................................................................................................................... 19

IPv6 Address

............................................................................................................................................................... 20

DNS

................................................................................................................................................................................ 20

Further information ....................................................................................................21

3

EN

Safety instructions

General safety instructions

• Before switching on and operating the system, rst read this safety advice and the operating instructions.

• Keep the operating instructions in a safe place for later use.

• Installation, commissioning and maintenance of the system may only be carried out by authorised

individuals and in accordance with the installation instructions - ensuring that all applicable standards and

guidelines are followed.

• Protect the devices from water penetration and humidity, since these can cause lasting damage.

• Should moisture nevertheless enter the system, under no circumstance switch on the devices under these

conditions, instead send them for examination to an authorised specialist workshop.

• The system must never be used outside of the technical specications, since this can destroy it.

• The device must be protected from excesses of heat, dust, humidity and vibration.

• When separating the system from the voltage supply, only ever use the plug to pull out the cable. Never

pull directly on the cable itself.

• Lay the connecting cables carefully and check that they are not mechanically stressed, kinked or damaged

and that no humidity can penetrate into them.

• In the event of a malfunction, please inform your supplier.

• Maintenance and repairs may only be carried out by authorised specialist personnel.

• The system must be isolated from the power supply before opening the housing.

• The device may only be opened by qualied service personnel. Unauthorised access invalidates any

warranty claim.

• Connection cables should always be exchanged through Videor E. Hartig GmbH.

• Use only original spare parts and accessories from Videor E. Hartig GmbH.

• The housing should only be cleaned using a mild domestic cleaning agent. Never use solvents or petrol as

these can permanently damage the surface.

• During installation, it is essential to ensure that the seals provided are correctly installed and that they are

not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.

• The installer is responsible for the maintenance of the enclosure as per the technical data, e.g. by sealing

the cable outlets with silicone.

• Wire end ferrules should be used when shortening the exible connection cables.

• The devices may only be operated in the temperature range indicated in the data sheet and within the

dened air humidity range.

Product - Specic Safety Instructions

• The camera may never be pointed directly at the Sun with the aperture open (this will destroy the sensor).

• It is unavoidable that during manufacture and to a certain extent during later use, humidity will be present

in the ambient air within the device’s housing. In the event of large temperature uctuations, this humidity

may condense inside the housing.

• To avoid this condensation inside the very tightly sealed housing, the manufacturer has inserted silica gel

sachets in the housing of the various camera types.

• It is however a physical given, that these silica gel bags will reach saturation after a certain amount of time.

They should therefore be replaced with new silica gel sachets.

• During installation, it is essential to ensure that the seals provided are correctly installed and that they are

not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.

• A multipolar, easily accessible isolation device should be installed in the proximity of the IR Spotlight, in

order to disconnect the device from the power supply for service work.

• The earth connection must be made according to the low impedance requirement of DIN VDE 0100.

• Subsequent painting of the equipment surface can impair the function.

• Any warranty claim is invalidated by subsequent painting.

• A safety margin of > 1m from the spotlight must be maintained when viewing directly into the IR Spotlight

in a darkened environment.

• Do not look directly at invisible LED radiation using optical instruments (e.g. a reading glass, magnifying

glass or microscope), since this can endanger the eyes, LED Class 1M.

• Operation of the IR spotlight with a defective cover or during repair is prohibited.

4

Class A device note

This is a Class A device. This device can cause malfunctions in the living area; in such an event, the operator may

need to take appropriate measures to compensate for these.

WEEE (Waste Electronical & Electronic Equipment)

Correct Disposal of This Product (Applicable in the European Union and other European countries with separate

collection systems).

This marking shown on the product or its literature, indicates that it should not be disposed with

other household wastes at the end of its working life. To prevent possible harm to the environment

or human health from uncontrolled waste disposal, please separate this from other types of wastes

and recycle it responsibly to promote the sustainable reuse of material resources. Household users

should contact either the retailer where they purchased this product, or their local government

oce, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase

contract. This product should not be mixed with other commercial wastes for disposal.

Graphical symbols

Please pay attention to the safety instructions, and carefully read through this instruction guide before initial

operation.

Important points of warning are marked with a caution symbol.

i

Important points of advice are marked with a notice symbol.

5

EN

Parts supplied

• Camera

• Operating Instruction

• CD

• Mounting Template

• Cable Signal Sticker

• Plastic Anchor: 6 x 30mm (4x)

• Mounting Screw: 4 x 30mm (4x)

• Assembly Screw: 4 x 15mm (4x)

• Torque Wrench: 3mm (1x)

• Coupler for RJ45 Cable (1x)

• Wiring Connector: (1x)

• Video Sub-Out Cable

• Easy Bracket

6

Part names

Sunshield bolt

Ethernet & Power cable

Front case Rear case

Bracket

Easy bracket

Sunshield

Lock/Unlock screw

Micro SD Card slot

IP Reset

USB Connector

COVER OPEN

7

EN

Part names

Sunshield bolt

Ethernet & Power cable

Front case Rear case

Bracket

Easy bracket

Sunshield

Lock/Unlock screw

Micro SD Card slot

IP Reset

USB Connector

Installation instructions

CAUTION: The camera’s base should be attached to a structural

object, such as concrete, hard wood, wall stud or ceiling rafter

that supports the weight of the camera. If necessary use appro-

priate mounting material (e.g. anchors) instead of the material

enclosed with the camera.

1. Locate the mounting template at the installation position and drill the ceiling or

wall if needed.

i

The easy bracket can not be installed on the ceiling.

2. Place the easy bracket on pre-drilled position and fix it through using mounting

screws(4x30mm). Skip this step when an easy bracket is not installed.

3. Route the ethernet and power cable to the connecting place. Hook up the

camera bracket with the easy bracket as illustrated below.

4. Fix the camera bracket through using assembly screws (4x15mm).

5. Set the camera’s viewing angle.

6. Put the sunshield to the camera unit and tighten the sunshield-bolts.

8

CAUTION:

Extreme care should be taken NOT to scratch the surface of win-

dow while the camera installing or adjusting.

Care should be taken the cable is NOT to be damaged, kinked or

exposed in the hazardous area.

Do not expose the camera directly to a strong light source such

as the sun or spot light.

Pan & Tilt adjustments

• Unlock the screw on the camera bracket through using the torque wrench supplied

• Set the camera’s viewing angle then lock the screw on the bracket.

1. Pan limit: Pan is limited to +/- 90°.

Assembly Screw: 4x15mm

Torque Wrench

Mounting Screw: 4x30mm

Cable exit

REAR VIEW

9

EN

90

°9

0°

2. Tilt limit: Tilt is limited to 0°(2°) min ~ 90° max. for wall(ceiling) installation respec-

tively with reference to the wall(ceiling) when the inclination of camera module is

0°, that is, the image is aligned horizontally.

90°

88°

3. Inclination limit (Horizontal image alignment): Inclination limited to +/-90° max.

on the wall on the ceiling

10

Adjustment of viewing angle with a bracket

Power supply connections

Make sure the power is removed before the installation. Camera can work with either

24VAC or 12VDC, dual voltage power and PoE (IEEE Std. 802.3af). Primary and secondary

grounds are completely isolated to avoid the possible ground loop problems.

1. Plug the network cable into RJ-45 Ethernet Port. If PoE is the unique power, there

will be no need to connect Power terminal.

2. When DC12V or AC24V Local power is necessary, connect the low voltage (DC12V

or AC24V) rst, then plug the AC adapter to AC outlets to avoid an improper reset

from power jitter and a damage from the surge voltage when no load.

i

When PoE and local dual power are connected at the same time, local power has

priority.

Attach the Signal Assignment Sticker in a visible spot for wiring reference.

Torque wrench

Lock / Unlock

screw

Audio-OUT (Orange wire)

AC24V/DC12V (Red wire)

AC24V/GND (Black wire)

Alarm-IN (Green wire)

Alarm-OUT (Blue wire)

GND (Gray wire)

Audio-IN (Brown wire)

GND (Gray wire)

LAN Cable with

RJ-45 and Protection Cap

BNC

11

EN

Quick Network Setup

1. After the camera is connected to the network, start ‘eneo Site Manager’ tool

(downloadable from www.eneo-security.com).

2. You will get a list of cameras connected to the local network. Highlight your cam-

era in the list and open a context menu with a click of the right mouse button.

3. Select the „Set IP Address [dhcp / static]“ option to open a window for setting the

cameras IP properties. When you are done click the „OK“ button to update the

camera settings.

4. By default the camera is set to DHCP. If there is no DHCP server present in the net-

work the camera will fall back to a default IP address after a while. In this scenario

please only add one camera at a time to the network to avoid conicts due to

identical IP addresses.

The network camera‘s default IP address is: 192.168.1.10.

5. Right clicking the device name in the eneo Site Manager will bring up the context

menu. Use the ‘Open Device Web Site’ option to access the camera.

6. The web viewer login page will open up in your default web browser.

In case of Microsoft Internet Explorer install Active-X named VIDEOR E. Hartig

GmbH according to the instruction at the bottom of the browser.

7. Use the default user name and password to log in.

Default user name: admin

Default password: admin

12

Web viewer description

(A) Menu button: Click the button to show or hide the setup menu bar.

(B) Model name: Show a camera model name connected.

(C) Select Language: Set the web viewer language English, German or French.

(D) Main setup menu bar: Set the camera or network functions.

(E) Camera monitoring window: Display the currently connected camera view or

function.

(F) Log out and exit the web viewer

(G) Help the menu function. Click and pop-up the page about current menu

description.

Player control & Display

(1) Pause: Pauses the live view.

(2) Snapshot: Captures the image in .jpg format with the current stream resolution.

13

EN

(3) Speaker: Enables audio to be output to the audio out port.

(4) Microphone: Enables audio to be input from the audio input port.

(5) Record: (Available with the built-in Storage feature version only) Records the live

video in H.264 format to the equipped storage memory like SD, SDHC or SDXC

from the video stream selected in the RECORD menu.

(6) Window Fit: Display live view to t the window size.

(7) Full Screen: Resizes the live view display to t to the monitor resolution. ESC key

returns to the previous view.

(8) Custom: Selects the live view display scale, 0%~200%, by the control bar. 100% is

the original size.

Video Stream

Selects the video source stream to display the live view only.

Protocol

Selects the network protocol out of HTTP, TCP or UDP.

PTZ Control

(Available with AF version & the built-in motor driven V/F lens version only)

User Manual

Help the menu function.Click and pop-up the page about current menu description.

14

Setup Menu Table

Category Menu Conguration

LIVE VIEW

Player Control

Pause, Snapshot, Speaker, Microphone, Record

Display (Window Fit, Full Screen, Custom)

Video Stream Stream1, Stream2, Stream3

Protocol HTTP, TCP, UDP

PTZ Contol (*) Zoom, Focus, Push AF

PLAYBACK Event Search, Timeline Search, Timeline Bar

SETUP

Information General, System Information, Open source Information

Video & Image

Source

Stream1/2/3, Snapshot

Image

Basic

Sharpness[DDE], Palette,

FFC Warn, Enable ip image,

Enable mirror image

OSD

Enable text OSD, Enable

date&time OSD

AGC

Mode, Auto Preset, Contrast,

Brightness, Filter, SSO, ACE,

Plateau Level, Max Gain

FFC

Mode, Interval (FFC Interval,

Low Gain FFC Interval),

Temperature (Temp Change,

Low Gain Temp Change)

Thermal

Spot Meter (Mode,

Thermometer), Isothermal

(Mode, Threshold Unit,

Upper/ Middle/ Lower

Threshold)

VerticalView Mode, Rotation

Privacy Mask Color, Name

Digital Zoom Level

Audio

Compression, Sample rate, Bitrate, Input Volume, Output Volume, Audio auto activation

on ONVIF access

15

EN

SETUP

Record

Overwrite when storage is full,

Continuous record setting

Schedule

Storage Format, Remove, Storage Information

Event

Triggers

Motion, VCA, Tamper, Alarm In, System, Manual, Network,

Timer, Temperature

Actions

Record, Alarm Out, E-Mail, FTP, Video Boost, Notication

Server

Rules Event Processing, ONVIF Mapping

System

Security User, HTTPS, IP Filter, ONVIF, Video Stream, Export/Import

Date & Time Current Time, New Time, Time Zone, Date & Time Display

Network TCP/IP, DDNS, RTP, UPnP, Zeroconf, Bonjour

Language English, German , French, Polish, Finnish, Korean

Maintenance

Maintain (Restart, Reset, Default), Upgrade, Setup Export,

Setup Import

Log & Report Logs (Database Capacity, Search Condition, Log List), Report

USER MANUAL

LOG OUT

(*) Available only with the built-in Motor driven V/F lens version

16

Quick Setup

Information

Shows the overall information about the system such as Model name, MAC address, IP

address, Zeroconf, IP address, Firmware version, Server time, Running time, CPU usage,

Inbound/Outbound Bandwidth and Open source list.

Users

Manages the user accounts by names, groups and authorities.

• Mark ENABLE ANONYMOUS VIEWR LOGIN if anyone is permitted to login anony-

mously. Accessing SETUP menu with the anonymous login will exit and require ID/

Password login.

• > USERS : Can be added, edited or deleted.

17

EN

Click the Add, Edit, or Delete button for managing user account.

Add

To add a new user:

1. Click the Add tab, and type a new user name. (1 to 14 alphanumeric characters).

User names are not case sensitive.

2. Type a password and retype conrm password. (1 to 8 alphanumeric characters).

Passwords are case sensitive.

3. Select one of the groups you wish to assign to the user.

4. Click the OK button to save the settings and add a new user.

Edit

To edit a user:

1. Select one of the User Names in the User List you want to modify.

18

2. Click the Edit tab, then new pop-up window appears.

3. Type a password (1 to 8 alphanumeric characters) and retype conrm password.

The user name can’t be modied.

4. Select one of the groups you wish to assign to the user.

5. Click the OK button to save the settings and modify a user.

Delete

To delete a user:

1. Select one of the User Names in the User List you want to remove.

2. Click the Delete tab. A dialog box appears with conrmation message.

3. Click the OK button. The user prole is removed from the User List prole.

Date & Time

Current Time

Shows the current date and time. Clicking SAVE tap updates and saves the date and time

with the selected time in NEW TIME.

New Time

Select one of the following server time.

• Synchronize with computer time: Obtains the time from the computer.

• Set manually: Sets the date and time manually.

• Synchronize with NTP Server: Obtains the time from the assigned NTP server at

every hour in INTERVAL. The NTP server’s IP address or host name has to be speci-

ed in the time server.

Time Zone

Select the time zone to be referenced to the NTP server where the camera is installed

Mark AUTOMATICALLY ADJUST FOR DAYLIGHT SAVING CHANGES check box to update

the time automatically with daylight savings

19

EN

Day & Time Display

Select the date & time formats to be displayed.

Network

The DHCP (Dynamic Host Conguration Protocol) server has a feature that automatically

assigns an IP address to the device if there is a device on the network.

IPv4 Address

Obtain IP address via DHCP :

Gets the IP address assigned by the DHCP (Dynamic Host Conguration Protocol) server.

Status:

‘Allocated’ shows that the IP address is obtained from the DHCP.

20

IP address, Subnet mask, Gateway:

Displays the current IP address which is obtained from the DHCP

Use the following IP address:

Select the choice box if you want to assign the IP address manually.

IPv6 Address

Mark ENABLE check box to use IPv6 address and click SAVE button, then new IPv6 address

will be obtained.

DNS

Obtain DNS address via DHCP :

Obtains the DNS address automatically assigned by DHCP server.

Use the following DNS address :

Requires manual input as per below.

• DOMAIN NAME : Enter the domain for the host name

• PRIMARY DNS SERVER : Enter the IP address of the primary DNS server.

• SECONDARY DNS SERVER : Enter the IP address of the secondary DNS server.

La pagina si sta caricando...

Eneo ITB-7SF0019M0A Quick Installation Manual

Questo manuale è adatto anche per

Eneo ITB-7SF0019M0A Quick Installation Manual

in altre lingue

Documenti correlati

Altri documenti