Dolmar HT-2556 D Manuale utente

HEDGE TRIMMER

TAILLE-HAIES

BENZIN-HECKENSCHERE

TOSASIEPI

HEGGESCHAREN

CORTASETOS

WARNING:

To reduce the RISK of injury, user must read and understand the instruction manual before using the Hedge Trimmer.

Manufacturer reserves the right to change specications without notice.

Specications may differ from country to country.

Do only hand over the Hedge Trimmer together with this manual.

AVERTISSEMENT :

An d’éviter les blessures, l’utilisateur doit lire et comprendre les instructions de ce manuel avec attention avant d’utiliser le taillehaies.

Le fabricant se séserve le droit de modier les spécications sans avertissement préalable.

Les spécications peuvent varier d’un pays à l’autre.

Lorsque vous n’utiliser pas le toujours accompagner l’appareil du manuel contenant les instructions.

WARNUNG:

Um das Risiko von Verletzungen zu verringern, sollte der Benutzer vor verwendung des Benzin-Hechenschere die Bedienungsanleitung

sorgfältig durchlesen und sich mit dem Gerät vertraut machen.

Der Hersteller behält sich das Recht vor, Spezikatioen ohne Vorankündigung zu ändern.

Das Benzin-Hechenschere nur zusammen mit dieser Bedienungsanleitung aushändigen.

AVVERTENZE:

Per ridurre il rischio di ferite, l’utilizzatore è tenuto a leggere ed a capire questo manual d’istruzioni prima di mettere in funzione il tosasipi.

Il produttore si riserva il diritto di modicare le caratteristiche del prodotto senza preavviso. Le caratteristiche di questo tosasipi possono

cambiare da Paese e Paese.

Consegnare il tosasipi solo se accompagnato da questo manuale di istruzioni.

WAARSCHUWING:

Om het gevaar op verwondingen te vermindeen, dlent men de instructies te lezen en te begrijpen alvorens de heggescharen in gebruik te

nemen. De fabricant houdt het recht wijzigingen in de specicaties aan te brengen zonder schrittelijke kennisgeving.

Specicaties kunnen verschillen van land tot land.

Gebruik de heggescharen alleen samen met deze instructies.

ADVERTENCIA:

Para reducir el riesgo de posibles lesiones, el usuario deberà leer y entender las instrucciones de este manual antes de utilizar el cortasetos

El fabricante se reserva el derecho de cambiar las especicaciones sin previo aviso.

Las especifcaciones pueden variar de un país a otro.

Ceda únicamente el cortasetos junto con este manual.

HT-2576 E

HT-2556 D

HT-2576 E

ORIGINAL INSTRUCTION MANUAL

MANUEL D’INSTRUCTIONS ORIGINAL

ORIGINALBEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI ORIGINALE

ORIGINELE GEBRUIKSAANWIJZING

MANUAL DE INSTRUCCIONES ORIGINAL

Downloaded from www.Manualslib.com manuals search engine

2

Thank you very much for selecting the DOLMAR Hedge Trimmer. We are

pleased to be able to offer you the DOLMAR Hedge Trimmer which is the result

of a long development program and many years of knowledge and experience.

The Hedge Trimmer models HT-2556 D and HT-2576 E combines the

advantages of state-of-the-art technology with ergonomic design, they are

light weight, handy, compact and represent professional equipment for a great

variety of applications.

Please read, understand and follow this booklet, which refers in detail

to the various points that will demonstrate its outstanding performance.

This will assist you to safely obtain the best possible results from your

DOLMAR Hedge Trimmer.

Table of Contents Page

SYMBOLS

It is very important to understand the following symbols when reading this instructions manual.

English (Original instructions)

Symbols .........................................................................2

Safety instructions ......................................................3-6

Technical data................................................................6

Designation of parts.......................................................7

Fuels/Refuelling ..........................................................8-9

Precautions before starting............................................9

Starting the machine....................................................10

Stopping the machine ..................................................10

Operation of the machine ...........................................11

Maintenance instructions ........................................12-14

Storage ........................................................................15

Maintenance schedule.................................................15

Fault location ...............................................................15

WARNING/DANGER

Read, Understand and Follow

Instruction Manual

Forbidden

No Smoking

No Open Flame

Protective Gloves must be Worn

Keep the Area of Operation

Clear of All Persons and Pets

Wear Eye and Ear Protection

Fuel and Oil Mixture

Engine-manual Start

Emergency Stop

First Aid

Recycling

ON/START

OFF/STOP

CE-mark

Downloaded from www.Manualslib.com manuals search engine

3

General Instructions

THIS MACHINE CAN CAUSE SERIOUS INJURIES. Read the Instructions –

carefully for the correct handling, preparation, maintenance, starting and

stopping of the machine. Be familiar with all controls and the proper use of

the machine. (1)

It is recommended only to loan the Hedge Trimmer to people who have –

proven to be experienced with Hedge Trimmers.

Always hand over the instruction manual.

First-time users should ask the dealer for basic instructions to familiarise –

themselves with the handling of an engine powered Hedge Trimmer.

Children and young persons aged under 18 years must not be allowed –

to operate the Hedge Trimmer. Persons over the age of 16 years may

however use the device for the purpose of being trained only while under the

supervision of a qualied trainer.

Use the Hedge Trimmer with the utmost care and attention. –

Operate the Hedge Trimmer only if you are in good physical condition. –

Perform all work calmly and carefully. The user has to accept liability for

others.

Never use the Hedge Trimmer after consumption of alcohol or drugs, or if –

feeling tired or ill. (2)

Intended use of the machine

The Hedge Trimmer is only designed for the purpose of trimming bushes and –

hedges, and must not be used for any other purpose.

Do not abuse the Trimmer.

Personal protective equipment

The clothing worn should be functional and appropriate, i.e. it should be tight- –

tting but not cause hindrance. Do not wear jewelry or loose clothing which

could become entangled with bushes or shrubs, or the machine.

In order to avoid eye, hand or foot injuries as well as to protect your hearing, –

the following protective equipment and protective clothing must be used

during operation of the Hedge Trimmer.

During operation of the Hedge Trimmer always wear goggles or a visor to –

prevent eye injuries. (3)

Wear adequate noise protection equipment to avoid hearing impairment, ear –

muffs, ear plugs, etc. (3)

We strongly recommend that the user wears work overalls. (4) –

Special gloves made of thick leather are part of the prescribed equipment and –

must always be worn during operation of the Hedge Trimmer. (4)

When using the Hedge Trimmer, always wear sturdy shoes with a non- slip –

sole. protects against injuries and ensures a good footing. (4)

SAFETY INSTRUCTIONS

(1)

(2)

(3)

(4)

Downloaded from www.Manualslib.com manuals search engine

4

(6)

(7)

(8)

(9)

Resting•

Transporting•

Refuelling•

Maintenance•

Tool Replacement•

3 meters

(10 feet)

Starting up the Hedge Trimmer

Please make sure that there are children or other people within a working –

range of or 15 meters (5), also pay attention to any animals in the working

vicinity. Avoid operating while people, especially children are nearby.

Before operating, always check that the Hedge Trimmer is safe for –

operation:

Check the security of the throttle lever. The throttle lever should be checked

for smooth and easy action. Check for proper functioning of the throttle lever

lock. Check for clean and dry handles and test the function of the STOP

Switch. Keep handles free of oil and fuel.

Start the Hedge Trimmer only in accordance with the instructions.

Do not use any other methods for starting the engine (6)!

Use the Hedge Trimmer only for applications specied. –

Start the Hedge Trimmer engine only after the entire assembly is done. –

Operation of the Hedge Trimmer is permitted only after all the appropriate

accessories are attached!

Before starting, make sure that the cutter blade will not contact any objects –

such as branches, stones, etc.

The engine is to be stopped immediately if there are any engine problems. –

When working with the Hedge Trimmer, keep both hands on handles always –

wrap your ngers tightly around the handle, keeping the control handle

cradled between your thumb and forenger. Keep your hand in this position to

have your machine under control at all times. Make sure your control handle

is in good condition and free of moisture, pitch, oil or grease.

Always ensure a safe, well-balanced footing.

Only use outdoors. –

Always be aware of your surroundings and stay alert for possible hazards –

that you may not hear due to the noise of the machine.

Operate the Hedge Trimmer in such a manner as to avoid inhalation of the –

exhaust gases. Never run the engine in enclosed rooms (risk of suffocation

and gas poisoning). Carbon monoxide is an odorless gas. Always ensure

there is adequate ventilation.

Stop the engine when resting and when leaving the Hedge Trimmer –

unattended. Place it in a safe location to prevent danger to others, setting re

to combustible materials or damage to the machine.

Never lay down the hot Hedge Trimmer onto dry grass or onto any –

combustible materials.

To reduce re hazard keep engine and silencer free of debris, leaves, or –

excessive lubricant;

Never operate the engine with a faulty exhaust mufer. –

Stop the engine during transport (7). –

Stop the engine or disconnect from mains before: –

Cleaning or when cleaning a blockage; –

Checking, maintenance or working on the machine. –

Position the Hedge Trimmer safely during car or truck transportation to avoid –

fuel leakage.

When transporting the Hedge Trimmer ensure that the fuel tank is completely –

empty to avoid fuel leakage.

When transporting or storing the machine always t the cutting device guard. –

Refuelling

Stop the engine before refuelling (7), keep well away from open ame (8) and –

do not smoke.

Do not attempt to refuel a hot or a running engine. –

Avoid skin contact with petroleum products. Do not inhale fuel vapor. Always –

wear protective gloves during refuelling. Change and clean protective clothing

at regular intervals.

Take care not to spill either fuel or oil in order to prevent soil contamination –

(environmental protection). Clean the Hedge Trimmer immediately after fuel

has been spilt. Allow wet cloths to dry before disposing in proper, covered

container to prevent spontaneous combustion.

Avoid any fuel contact with your clothing. Change your clothing immediately if –

fuel has been spilled on it (danger hazard).

Inspect the fuel cap at regular intervals making sure that it stays securely –

fastened.

Carefully tighten the locking screw of the fuel tank. Change locations to start –

the engine (at least 3 meters away from the place of refuelling) (9).

Never refuel in closed rooms. Fuel vapors accumulate at ground level (risk of –

explosions).

Only transport and store fuel in approved containers. Make sure stored fuel is –

not accessible to children.

When mixing gasoline with two-stroke engine oil, use only gasoline which –

contains no ethanol or methanol (types of alcohol).

This will help to prevent damage to fuel lines and other engine parts.

(5)

15 meters

(50 feet)

Downloaded from www.Manualslib.com manuals search engine

5

Method of operation

Always use two hands to grip each handles during operation. –

Use the Hedge Trimmer only in good light and visibility. During cold seasons –

beware of slippery or wet areas, ice and snow (risk of slipping). Always

ensure a safe footing.

Never work on unstable surfaces or steep terrain. –

Never stand on a ladder and run the Hedge Trimmer. –

Never climb up into trees to perform cutting operation with the Hedge –

Trimmer.

To reduce the risk of stumbling and loss of control, do not walk backward –

while operating the machine.

Always stop the engine before cleaning or servicing the unit or replacing –

parts.

Do not operate the machine with a damaged or excessively worn cutting –

device.

Maintenance instructions

Be kind to the environment. Operate the Hedge Trimmer with as little noise –

and pollution as possible. In particular check the correct adjustment of the

carburetor.

Clean the Hedge Trimmer at regular intervals and check that all screws and –

nuts are securely tightened.

Never service or store the Hedge Trimmer in the vicinity of open ames, –

sparks, etc. (11).

Always store the Hedge Trimmer in a well-ventilated locked room and with an –

emptied fuel tank out of reach of children.

Do not attempt to repair the machine unless you are qualied to do so; –

First aid

In case of an accident make sure that a well-stocked rst-aid kit according to

DIN 13164, is available in the vicinity of the cutting operations.

Immediately replace any item taken from the rst aid kit.

When asking for help, please give the following information:

Place of accident –

What happened –

Number of injured persons –

Extend of injuries –

Your name –

Packaging

The DOLMAR Hedge Trimmer is delivered in a protective cardboard box to

prevent shipping damage. Cardboard is a basic raw material and is therefore

consequently reusable or suitable for recycling (waste paper recycling).

Observe and follow all relevant accident prevention instructions issued by the trade associations safety board and by insurance

companies.

DonotperformanymodicationstotheHedgeTrimmerasthiswillriskyoursafety.

The performance of maintenance or repair work by the user is limited to those activities as described in this instruction manual. All other work is

to be done by Authorized Service Agents.

Use only genuine spare parts and accessories supplied by DOLMAR authorized or factory service centers.

Use of non-approved accessories and tools means increased risk of accidents and injuries. DOLMAR will not accept any liability for accidents or

damage caused by the use of any non-approved accessories.

(10)

(11)

(12)

Downloaded from www.Manualslib.com manuals search engine

6

TECHNICAL DATA

Model HT-2576 E HT-2556 D

Dimensions (L x W x H) mm 1,041 × 280 × 258 840 × 246 × 225

Mass (with blade cover) kg 5.4 5.1

Volume (fuel tank) cm3600

Engine displacement cm324.5

Cutting length mm 750 560

Maximum engine performance kw 0.88

Stroke per minute min-1 4,180

Idling speed min-1 2,600

Clutch engagement speed min-1 3,600

Carburetor type type WALBRO WYL

Ignition system type Solid ignition system

Spark plug type NGK-BMR7A

Electrode gap mm 0.6 - 0.7

Vibration per

ISO 22867

Right handle

(Rear grip)

ahv eq m/s26.1 11.1

Uncertainty K m/s20.5 0.6

Left handle

(Front grip)

ahv eq m/s212.6 12.1

Uncertainty K m/s20.5 1.3

Sound pressure level average

according to ISO 22868

LPA eq dB (A) 96.4 96.2

Uncertainty K dB (A) 4.0 2.2

Sound power level according to

ISO 22868

LWA eq dB (A) 106.4 103.6

Uncertainty K dB (A) 1.7 2.1

Mixture ratio (fuel: DOLMAR 2-stroke engine oil) 50 : 1

Gear ratio 14 : 58

1) The data takes equally into account idling and racing speed operating modes.

For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible manufacturer declare that the following Dolmar machine(s):

Designation of Machine: Hedge Trimmer

Model No./ Type: HT-2556 D, HT-2576 E

Specications: see “TECHNICAL DATA” table

are of series production and

Conforms to the following European Directives:

2000/14/EC, 2006/42/EC

And are manufactured in accordance with the following standard or standardized documents:

EN ISO 10517

The technical documentation is kept by:

Dolmar GmbH,

Jenfelder Straße 38, Abteilung FZ,

D-22045 Hamburg, Germany

The conformity assessment procedure required by Directive 2000/14/EC was in Accordance with annex V.

HT-2556 D: Measured Sound Power Level: 104.6 dB (A)

Guaranteed Sound Power Level: 107 dB (A)

HT-2576 E: Measured Sound Power Level: 107.3 dB (A)

Guaranteed Sound Power Level: 109 dB (A)

3. 11. 2009

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, 446-8502, JAPAN

Downloaded from www.Manualslib.com manuals search engine

7

DESIGNATION OF PARTS

HT-2556 D

HT-2576 E

DESIGNATION OF PARTS DESIGNATION OF PARTS DESIGNATION OF PARTS

1 Blade 7Carburetor 13 Blade cover

2 Blunt extension 8STOP Switch (ON-OFF)

3 Front handle 9Throttle lever

4Recoil starter 10 Rear handle

5Fuel tank cap 11 Mufer

6Choke lever 12 Gearbox

Downloaded from www.Manualslib.com manuals search engine

8

Fuel and oil mixture

The engine of the Hedge Trimmer is a high-efciency two-stroke engine. –

It is run with a mixture of fuel and two-stroke engine oil. The engine is

designed for unleaded regular fuel with a min. octane value of 91 ROZ.

In case no such fuel is available, you can use fuel with a higher octane value.

This will not damage the engine, but may cause poor operating behaviour.

A similar situation will arise from the use of leaded fuel.

To obtain optimum engine operation and to protect your health and the

environment, only unleaded fuel should be used!

For lubricating the engine use a two-stroke engine oil (quality grade: TSC-3), –

which is added to the fuel.

The engine has been designed for use with DOLMAR two-stroke engine oil

and a mixture ratio of 50:1 only to protect the environment.

In addition, a long service life and a reliable operation with a minimum

emission of exhaust gases is guaranteed. It is absolutely essential to observe

a mixture ratio of 50:1 (DOLMAR 2-stroke engine oil), otherwise the reliable

function of the Hedge Trimmer cannot be guaranteed.

The correct mixture ratio: –

Mix 50 parts gasoline with 1 part DOLMAR 2-stroke engine oil (See table on

the right).

NOTE: For preparing the fuel-oil mixture, rst mix the entire oil quantity with

half of the fuel required. In an approved can which meets of exceeds all

local code standards, then add the remaining fuel.

Thoroughly shake the mixture before lling it into the Hedge Trimmer’s

tank.

It is not wise to add more engine oil than specied to ensure safe

operation. It will only result in a higher production of combustion

residues which will pollute the environment and clog the exhaust

channel in the cylinder as well as the mufer.

In addition, the fuel consumption will rise and the performance will

decrease.

Handling petroleum products

Utmost care is required when handling fuel. Fuel may contain substances

similar to solvents. Refuel either in a well ventilated area or outdoors. Do not

inhale fuel vapors, avoid any contact of fuel or oil with your skin.

If your skin comes in contact with these substances repeatedly and for an

extended period of time, it will desiccate.

Various skin diseases may result. In addition, allergic reactions are known to

occur.

Eyes can be irritated by contact with oil, fuel etc.

If oil, fuel, etc., comes into your eyes, immediately wash them with clear water.

If your eyes are still irritated, see a doctor immediately!

FUELS/REFUELLING

Observe the Safety Instructions on page 4

Gasoline 50:1

+

1,000 cm3 (1 liter)

5,000 cm3 (5 liters)

10,000 cm3 (10 liters)

20 cm3

100 cm3

200 cm3

Downloaded from www.Manualslib.com manuals search engine

9

Refuelling

The engine must be switched off. –

Stop the engine during refuelling, keep away from naked ames and do not –

smoke.

Take care not to spill either fuel or oil in order to prevent soil contamination –

(enviromental protection).

Clean the Hedge Trimmer immediately after fuel has been spilt.

Do not spill any fuel onto the engine. Wipe up if necessary to avoid re. –

Avoid any fuel contact with your clothing. Change your clothing instantly if –

fuel has been spilt on it (to prevent clothing catching re).

Inspect the fuel cap at regular intervals making sure that it can be securely –

fastened and does not leak.

Carefully tighten the fuel tank cap. Change location to start the engine (at –

least 3 meters away from the place of refuelling.)

Never refuel in enclosed rooms. Fuel vapours accumulate at ground lever. –

(Risk of explosions.)

Transport and store fuel only in approved containers. Make sure the fuel –

stored is not accessible to children.

Thoroughly clean the area around the tank cap to prevent dirt from getting –

into the fuel tank.

Unscrew the plug and ll the tank with fuel. Use a gauze funnel to lter the –

fuel.

Tightly screw on the plug by hand only. –

Clean around the screw plug and the tank after refuelling. –

Always wipe up any spilt fuel to prevent a re. –

Storage of fuel

Fuel cannot be stored for an unlimited period of time. –

Purchase only the quantity required for a 4 week operation period. –

Use approved fuel storage containers only. –

PRECAUTIONS BEFORE STARTING

Please make sure that there are no children or other people within a working –

range of 15 meters, also pay attention to any animals in the working vicinity.

Before use always check that the Hedge Trimmer is safe for operation. –

Check the cutting device is not damaged, the control lever for easy action

and check for proper function of the STOP Switch.

Rotation of the cutting device during idling speed is not allowed.

Check with your dealer for adjustment if in doubt. Check for clean and dry

handles and test function of the STOP Switch.

Start the Hedge Trimmer only in accordance with the instructions. –

Do not use any other methods for starting the engine. (See Starting)

Start the Hedge Trimmer engine only after the entire assembly is done. –

Operation of the engine is only permitted after all the appropriate accessories

are attached. Otherwise there is a risk of injury.

Before starting, make sure that the cutting device has no contact with objects –

such as branches, stones, etc.

Before trimming, inspect area for wires, cords, glass, or other foreign objects, –

which could come in contact with the blade.

Electrical shock. Be aware of any and all electric lines and electric fences. –

Check all areas for electrical lines before cutting.

3 meters

(10 feet)

15 meters

(50 feet)

Diagrammatic gure

Downloaded from www.Manualslib.com manuals search engine

10

STARTING THE MACHINE

Move at least 3 meters away from the place of refuelling. Place the Hedge

Trimmer on a clean area of ground make sure that the cutting tool does not

come into contact with the ground or any other objects.

Cold starting (When the engine is cold or it has been stopped for more than

5 minutes or when fuel is added to the engine.)

1. Push the I-O Switch (1) to “I” position.

2. Give a gentle push on the primer pump (2) repeatedly (7 to 10 times) until

fuel comes into the primer pump.

3. Move the choke lever (3) to position “START”.

4. Hold the unit down rmly so you will not lose control while cranking the

engine. If not held down properly, the engine could pull you off balance or

swing the cutting blade into an obstruction or your body.

5. Pull the starter handle slowly for 10 to 15 cm, and check the location of

pressure.

6. Pull strongly when pressurization can be felt and start the engine.

7. When the engine starts, return the choke lever to “Run”. Please note that

the choke lever will return to “Run” position automatically when the throttle

lever is operated and the throttle is opened.

8. Run the engine for approximately one minute at a moderate speed before

applying full speed.

NOTE: - If the starter handle is pulled repeatedly when the choke lever

remains at “Start” position, the engine will not start easily due to

excessive fuel intake.

- In case of excessive fuel intake, remove the spark plug and pull

the starter handle slowly to remove excess fuel.

Also, dry the electrode section of the spark plug.

Hot staring: (Restarting immediately after the engine has stopped)

When restaring a hot engine, rst try the above procedure: 1, 4, 5, 6.

If the engine does not start, repeat above steps 1-8.

NOTE: Do not pull the starter rope to its full extent and do not allow

the starter grip to be retracted without control, ensure that it is

retracted slowly.

STOPPING THE MACHINE

1. Release the throttle lever completely.

2. Push the STOP Switch (on/off switch) to “O”

position, the engine rotation will become low and

the engine will stop.

HT-2576 E

START

RUN

(1)

(2)

(3)

HT-2556 D

HT-2576 E HT-2556 D

Downloaded from www.Manualslib.com manuals search engine

11

OPERATION OF THE MACHINE

Never operate with a loose grip. –

Never touch the cutting device when starting the engine and during operation. –

Operate the Hedge Trimmer in such a manner as to avoid inhalation of –

the exhaust gases. Never run the engine in enclosed rooms (Risk of gas

poisoning). Carbon monoxide is an odorless gas.

All protective installations and guards supplied with the machine must be –

used during operation.

Never operate the engine with a faulty exhaust mufer or if it is missing. –

Use the Hedge Trimmer only in good light and visibility. –

During the winter season beware of slippery or wet areas, ice and snow.

(Risk of slipping.) Always ensure a safe footing.

Never stand on a ladder and run the Hedge Trimmer. Keep both feet on the –

ground.

Never climb up the trees with the Hedge Trimmer to perform cutting –

operation.

Never work on unstable surfaces. –

Remove sand, stone, nails, wire, etc. found within the working area. –

Foreign objects may damage the cutting blades.

Before commencing cutting, the cutting blades must have reached full –

working speed.

Always hold the Hedge Trimmer rmly with both hands on the handles only. –

The right hand grips the front handle of model HT-2576 E. –

This is the way to safely operate the machine.

Use a rm grip with thumbs and ngers encircling the handles. –

When you release the throttle, it takes a few moments before the cutting –

blades stop.

The Hedge Trimmer must not be used for cutting with fast idle. The cutting –

speed cannot be adjusted with the throttle control in fast idle position.

When cutting a hedge, the machine should be held so that the blades form a –

15-30° angle with the cutting line.

If the Hedge Trimmer is used with circular movements against the edge of the –

hedge, the twigs will be thrown directly to the ground.

At vertical cutting, the Hedge Trimmer is used with circular pendulation, –

swinging up and down close to the hedge.

Pay special attention when cutting hedges which are laid out a long a wire- –

fence and have grown through the fence.

The blade must not contact the fence, otherwise the blades may be

destroyed.

Do not use the Hedge Trimmer continuously for a long time. It is normal to –

take a break of 10 to 20 minutes after every 50 minutes operation.

Should the cutting blades hit stones or other hard objects, immediately switch –

off the engine and inspect the cutting blades for damage. Replace damaged

blades before re-commencing work.

The engine must be switched off immediately in case of any engine problems. –

Operate the Hedge Trimmer with as little noise and contamination as –

possible. In particular check the correct setting of the carburetor and the fuel/

oil ratio.

Do not attempt to remove jammed cut material when blades are running. Put –

unit down, turn it off, and remove necessary cuttings.

Downloaded from www.Manualslib.com manuals search engine

12

MAINTENANCE INSTRUCTIONS

Turn off the engine and remove the spark plug connector when replacing or sharpening cutting tools, also when cleaning the cutter or cutting –

device or carrying out any maintenance.

Never straighten or weld a damaged cutting blade. –

Inspect the cutting blades with the engine switched off at short, regular intervals for damage. –

(Detection of hairline cracks by means of tapping-noise test.) Beware the teeth are sharp.

Clean the Hedge Trimmer at regular intervals and check that all screw and nuts are well tightened. –

Never service or store the Hedge Trimmer in the vicinity of naked ames to avoid res. –

Always wear leather gloves when handling or sharpening the blades as they are sharp. –

Blade sharpening

If the edges are rounded and do not cut well any more, grind

off only the shaded portions. Do not grind the contact surfaces

(sliding surfaces) of the top and bottom edges.

Before grinding, be sure to secure the blade rmly and –

switch off the engine and remove the spark plug cap.

Wear gloves, protective glasses, etc. –

An edge ground too much at a time or ground many times –

will lose its hardened layer. It becomes rounded and dull

very quickly in use.

Blade adjustment

The blades will wear with long use. When you nd that

trimming is not as good as when the blades were new, adjust

them as follows

1. Turn nut 1 loose.

2. Screw 2 in with the driver lightly till it stops turning, and

then screw it back one quarter.

3. Turn nut 1 tight, holding screw 2 at the same time with a

driver.

4. Lubricate the blades after adjustments above with light oil.

5. Start the engine and operate the engine throttle on and off

for a minute.

6. Stop the engine and touch the blades with your hand. If they are warm enough for you to keep your hand on, then you have made the

proper adjustment. If they are too hot for you to keep touching, give screw 2 a little more turnback and repeat 5 to see if they are properly

adjusted.

NOTE: Never fail to stop the engine before making the adjustment.

The blades have a slot around screw 2.Incaseyounddustintheendofanyoftheslots,cleanit.

NOTE: For enough time of blade stop (EN774), be sure to make the blade adjustment before operation.

1

4

5

6

7

23

1 Hexagonal U nut

2 Truss screw

3 Flat washer

4 Blunt extension

5 Blade guide

6 Upper blade

7 Lower blade

Disk grinder

Edge cross section

Holding the disk grinder at a 45°

angle, grind the edge off to the dotted

line to sharpen the rounded tip.

Downloaded from www.Manualslib.com manuals search engine

13

Checking and adjusting the idling speed

The cutting blade should not when the control lever is fully released.

Idle speed should be set to 2,600 rpm. –

If necessary, correct it by means of the idle screw (the cutting blade must not

run when the engine is on idle).

Clockwise: for faster rate of revolution•

Counter-clockwise: for slower rate of revolution •

Check that there is sufcient difference between idling and clutch

engagement speed to ensure that the cutting tool is at a standstill while the

engine is idling. (If necessary, reduce idling speed.) If the tool still continues

to run under the idling conditions, consult your nearest authorised service

agent.

The clutch should engage at minimum 3,250 rpm.•

Check the functioning of the STOP Switch, the lock-off lever, the control •

lever, and the lock button.

Cleaning of air cleaner - Every 8 hours (Daily)

Remove the air cleaner cover. –

Take out the sponge element, wash it in lukewarm water and dry it –

completely.

After cleaning, put back the sponge element and the air cleaner cover. –

NOTE: If there is excessive dust or dirt adhering to the air cleaner, clean it

every day. A clogged air cleaner may make it difcult or impossible

to start the engine or increase the engine rotation speed which could

cause damage.

Checking the spark plug - Every 8 hours (Daily)

Only use the supplied universal wrench to remove or to install the spark plug. –

The gap between the two electrodes of the spark plug should be 0.6 to –

0.7 mm. If the gap is too wide or too narrow, adjust it. If the spark plug is

clogged with carbon or fouled, clean it thoroughly or replace it. Use an exact

replacement.

Supply of grease and lubricant

Supply grease to the gear case through the grease hole every 10 to 20 hours. –

(Shell alvania No.3 or equivalent)

0.6 - 0.7 mm

Downloaded from www.Manualslib.com manuals search engine

14

Suction head in the fuel tank

The felt lter (1) of the suction head is used to lter the fuel required by the –

carburetor.

A periodical visual inspection of the felt lter is to be conducted. –

For that purpose, open the tank cap, use a wire hook and pull out the suction

head through the tank opening.

Filters found to have hardened, been polluted or clogged up are to be

replaced.

Insufcient fuel supply can result in the admissible maximum speed being –

exceeded. It is therefore important to replace the felt lter at least quarterly to

ensure satisfactory fuel supply to the carburetor.

Cleaningofmuferexhaustport

Check of mufer exhaust port (2) regularly. –

If it is clogged by carbon deposits, carefully scratch the deposits out with a –

suitable tool.

Do not allow carbon to fall into engine ports.

Any maintenance or adjustment work that is not included and described in this manual is to be performed by Authorized Service Agent only.

Daily checkup and maintenance

To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular

intervals.

Before operation, check the machine for loose screws or missing parts. Pay particular attention to the tightness of the cutter blade screws. –

Before operation, always check for clogging of the cooling air passage and the cylinder ns. Clean them if necessary. –

Perform the following work daily after use: –

Clean the Hedge Trimmer externally and inspect for damage.•

Clean the air lter. When working under extremely dusty conditions, clean the lter several times a day.•

Check the blades for damage and make sure they are rmly mounted.•

(1)

(2)

Downloaded from www.Manualslib.com manuals search engine

15

STORAGE

MAINTENANCE SCHEDULE

General Engine assembly,

screws and nuts

Visual inspection for damage and tightness

Check for general condition and security

After each refuelling Throttle lever

Safety lock key

STOP switch

Functional check

Daily Air lter

Cooling air duct

Cutting tool

Idling speed

To be cleaned

Check for damage and sharpness

Inspection (cutting tool must not move)

Weekly Spark plug

Mufer

Inspection, replace if necessary

Check and if necessary clean the opening

Quarterly Suction head

Fuel tank

To be replaced

To be cleaned

Shutting down procedure Fuel tank

Carburetor

Empty fuel tank

Operate until engine runs out of fuel

FAULT LOCATION

Fault System Observation Cause

Engine not starting or

under difculties

Ignition system Ignition spark is present Faulty fuel supply or compression system, mechanical defect

No ignition spark STOP-switch operated, wiring fault or short circuit, spark

plug or connector defective, ignition module faulty

Fuel supply Fuel tank lled Incorrect choke position, carburetor defective, suction head

(gas line lter) dirty, fuel supply line bent or interrupted

Compression Inside of engine Cylinder bottom gasket defective, crankshaft seals damaged,

cylinder or piston rings defective

Outside of engine Improper sealing of spark plug

Mechanical fault Starter not engaging Broken starter spring, broken parts inside of the engine

Warm start problems Tank lled

Ignition spark existing

Carburetor contaminated, have it cleaned

Engine starts but dies

immediately

Fuel supply Tank lled Incorrect idling adjustment, suction head or carburetor

contaminated

Fuel tank vent defective, fuel supply line interrupted, cable or

STOP-switch faulty

Insufcient

performance

Several systems may

simultaneously be affected

Engine idling Air lter contaminated, carburetor contaminated, mufer

clogged, exhaust duct in the cylinder clogged

When keeping the machine in storage for a long time, drain fuel from –

the fuel tank and carburetor, as follows: Drain all fuel from the fuel

tank.

Remove the spark plug and add a few drops of oil into the spark plug –

hole. Then, pull the starter gently to conrm that oil lm covers the

engine inside and tighten the spark plug.

Clear dirt or dust from the cutter blade and outside of engine, wipe –

them with a oil-immersed cloth and keep the machine at a place as

dry as possible.

Drain fuel

Humidity

Downloaded from www.Manualslib.com manuals search engine

16

Vous venez d’acheter un Taille-Haies DOLMAR, fruit d’importants programmes

de développement et de nombreuses annétudes et d’expérience-et nous vous

en remercions.

Les modéles HT-2556 D, HT-2576 E légers, praques et compacts, allient les

avantages d’une technologic de pointe à une conception ergonomique, et sont

des outils de professionnels pour de norebreuses applications.

Lire attentivement ce manuel et suivre les instructions données. Il décrit

en détail les divers points démontrant les exceptionnelles performances

dusoufeur.Cecivouspermettrad’obtenirlesmeilleursrésultatsdece

Taille-Haies.

Table des matières Page

SYMBOLES

Lors de la lecture de ce manuel, prêtez une attention particuliêre aux symboles ci-après :

Français (Instructions d’origine)

Symboles .....................................................................16

Consignes de sécurité ............................................17-20

Données techniques ....................................................20

Liste des pieces ...........................................................21

Melange de carburant et d’huile .............................22-23

Precautions a observer avant le demarrage................23

Demarrage de la machine ...........................................24

Arret de la machine .....................................................24

Fonctionnement de la machine ...................................25

Instructions de maintenance...................................26-28

Stockage......................................................................29

Programme d’entretien ................................................29

Localisation des défauts ..............................................29

Attention! Danger!

Lire ct suiver le manuel de fonctionnenent

Interdit

Interdiction de fumer

Interdiction d’utilisation de produits

Inammables

Port de gants de protection obligamire

Zone de fonctionnement interdite aux

humains et aux animanx

Port de lunettes de protection er cache-

creilles obligatoire

Essence et huile

Moteur - Mise en marche manuelle

Arrct durgence

Premiers secours

Recyclage

Marche/EF

Marche/HF

Logo de la CE

Downloaded from www.Manualslib.com manuals search engine

17

Généralités

CET APPAREIL PEUT PROVOQUER DES BLESSURESGRAVES. –

Veuillez lire attentivement le manuel d’instruction an de manipuler,

entretenir, mettre en route et arretêr correctement l’appareil. Chaque

utilisateur est prié de se familiariser avec la totalite des commandes et des

modes d’utilisation appropriés du taille-haies. (1)

Il est recommandé de prêter le taille - haies uniquement aux personnes –

expérimentées dans la manipulation de taille - haies.

Remettez leur toujours le manuel d’instructions.

Les premiers utilisateurs devraient demander des instructions de base au –

concessionnaire an de se familiariser à la manipulation d’un taille - haies

matorisé.

Les enfants et les jeunes gens de moins de 18 ans ne devraient pas être –

autorisés à faire fonctionner le taille - haies. Les personnes de plus de 16 ans

peuvent cependant utiliser la machine pour s’entraîner à la seule condition

qu’ils soient sous la surveillance d’une professeur qualié.

Utilisez le taille - haies avec un soin et une vigilance extrêmes. –

Utilisez le taille - haies uniquement si vous êtes en bonne condition –

physiqulue. Effectuez tous les travaux avec calme et soin.

L’utilisateur doit accepter la responsabilité des autres personnes.

N’utilisez jamais le taille - haies après absorption d’alcool ou de médicaments –

ou si vous vous sentez fatigué ou malade. (2)

Fonction dela machine

Le taille - haies est conçu uniquement dans le but de couper des buissons et –

des haies et ne doit pas être utilisé pour tout autre tâche.

Prière de ne pas malmener le Taille - Haies

Equipement de protection personnel

Le volet de protection de l’appareil de coupe doit être monté lors du transport –

de la machine vers un autre lieu.

La tenue doit être fonctionnelle et appropriée, c’est-à-dire qu’elle doit être –

serrée sans toutefois entraver les mouvements. Ne portez pas de bijoux ou

d’habits susceptibles de s’entrelacer dans les buissons, les broussailles ou la

machine.

Utilisez l’équipement de protection et les habits de protection suivants lors de –

l’utilisation du taille - haies an d’eviter des blessures au niveau de la tête,

des mains ou des pieds ainsi qu’an de protéger votre ouïe.

Portez toujours des lunettes ou une visière pour éviter les blessures au –

niveau des yeux lors de l’utilisation du taille - haies. (3)

Portez un équipement de protection sonore approprié pour éviter les –

détériorations auditives, des boules Quies, des bouchons d’oreilles, etc. (3)

La combinaison de travail protège contre les projections de pierres et –

les débris. Nous recommandons fortement aux utilisateurs de porter une

combinaison de travail. (4)

Des gants spéciaux en cuir épais font partie de l’équipement prescrit et –

doivent toujours être portés lors de l’utilisation du taille - haies. (4)

Lors de l’utilisation du taille - haies, portez toujours des chaussures solides –

avec une semelle antidérapante. Elles vous éviteront des blessures et vous

garantiront une bonne stabilité. (4)

CONSIGNES DE SÉCURITÉ

(1)

(2)

(3)

(4)

Downloaded from www.Manualslib.com manuals search engine

18

(6)

(7)

(8)

(9)

Repos•

Transport•

Plein•

Matntenance•

Remplacementd’outils•

3 mètres

(10 pieds)

Mise en marche du Taille - haies

S’assurez qu’auoun enfant ou aucune autre personne ne se trouve à moins – de 15 mètres de la zone d’utilisation du taille-haies. S’assurez également qu’il

n’y a aucun animal dans les parages. Evitez de mettre l’appareil en marche

s’il y a du monde près de vous, notamment des enfants.

Avantl’utilisation,toujoursvérierlespointssuivantsand’assurerla – sécurité :

Vérier que la manette des gaz est bien xée. S’assurer que la manette des

gaz est facile à manoeuvrer et que son mouvement est régulier. S’assurer

que le verrou de la manette des gaz fonctionne correctement. S’assurer que

les poignées sont propres et sèches et vérier le fonctionnement du Bouton

« arrêt ». Veiller à ce qu’il n’y ait ni huile ni carburant sur les poignées.

Avant de mettre la machine en marche, assurez - vous que toutes les – instructions sont bien respectées.

N’utilisezpasd’autresméthodesdemiseenmarchedel’appareil(6).

N’utilisez la machine et les outils fournis que pour les applications spéciés. –

Ne mettez la machine en marche que lorsque tous les accessoires ont été

rnisenplace.L’appareilnefonctionnequelorsquetouslesaccessoires

appropriésysontx’rs.

Avant de démarrer l’appareil, s’assurer que la lame n’est pas en contact avec – d’autres objets, tels que branchages, pierres, etc.

En cas de problème du moteur, l’arrêter immédiatement. –

Lors de l’utilisation du Taille - Haies, toujours bien refermer les doigts sur la – poignée, de façon à avoir la poignée de commande entre le pouce et l’index.

Laisser la main à cette position pour avoir constamment le plein contrôle de

l’outil. Veiller à ce que la poignée de commande soit en bon état et libre de

toute humidité, pente, huile ou graisse.

Veiller à avoir toujours une bonne prise des pieds.

Utiliser exclusivement à l’extérieur. –

Restez toujours conscient de ce qui se passe autour de vous, et toujours – vigilant devant toute sorte de danger pouvant surveniret que vous n’aurez

pas entendu venir du fait du bruit que fait l’appareil en fonctionnement.

Pendant le fonctionnement de l’appareil, evitez toute inhalation de gaz – d’échappement. N’utilisez jamais l’appareil dans des endroits clôs (en raison

des riques d’étouffement et d’empoisonnement par les gaz d’echappement).

N’oubliez pas que le monoxyde de carbone est un gaz sans odeur. N’utilisez

l’appareil que dans un endroit bien aéré.

Coupez le moteur lorsque vous n’utilisez pas l’appareil, et mettezle en – lieu sûr pour éviter de blesser l’entourage, de mettre le feu anx matériaux

combustibles, ou d’endommager la machine.

Ne posez jamais la machine chande sur de l’herbe sèche ou des matériaux – combustibles.

An d’éviter tout risque d’incendie, s’assurez qu’auchu débris, feuilles ou – lubriant excessif ne soit resté attaché au moteur ou au silencieux.

Ne faites jamais fonctionner la machine si le silencieux pose probième. –

Conpez l’alimentation du moteur pendant le transport (7). –

Coupez le moteur ou débranchez-le avant : –

de nettoyer l’appareil ou de nettoyer un bourrage ;•

toute vérication, entretien ou travail sur l’appareil.•

Pendant le transport, évitez toute fuite de carburant. –

Pendant le transport, assurez - vous que le réservoir de carburant est – totalement vide.

Enclenchez systèmatiquement le dispositif de sûreté lors du transport ou de – l’entreposage de l’appareil.

Plein de carburant

Coupez le moteur (7), Assutez - vous qu’il n’y a aucune amme à proximité – (8).

Ne faites jamais le plein d’un moteur chaud ou en marche. –

Ne fumez pas. Evitez tout contact avec la peau eet les produits dérivés du – pétrole. N’inhalez pas les vapeurs d’essence. Portez toujours des gants de

protection. Chanzez et nettoyez régulièrement les gants de protection.

Veillez à ne pas renverser de carburants ou d’huile, pour éviter de contaminer – le sol (protection de l’environnement). En cas de fuite de carburant, même

légère, nettoyez immédiatement l’appareil. Faites toujours sécher les chiffons

avant de les jeter dans un conteneur approprié er couvert, pour éviter teut

risque de combustion spontanée.

Evitez tout contact du carburant avec les vêtements. Si nécessaire, changez – immédiaternent de vêtement.

Vériez régulièrement le bon fonctionnement du bouchon du réservoir. – Assurez - vous que le bouchon du réservoir est bien serré, et ne mettez le

moteur en marche qu’a un minimum de 3 m de l’endroit ou vous avez fait le

plein (9).

Ne faites jarnais le plein de carburant dansdes pièces fermées : les vapeurs – s’accumulent au niveau du sol (risque d’explosion).

Ne transportez et ne stockez du carburant que dans des conteneurs – appropriés. Veillez à ce que les enfants n’y aient pas accés.

Lorsque vous mélangez de l’essence et de l’huile pour moteur à deux temps, – utilisez uniquement de l’essence ne contenant ni éthanol, ni méthanol pour

ne pas endommager les pièces du moteur.

(5)

15 mètres

(50 pieds)

Downloaded from www.Manualslib.com manuals search engine

19

Méthoded’utilisation

Manipulez toujours le conpe-haies avec vos deux mains que vous glissez –

fermement dans chacune des poignées.

N’utiliser le Taille - Haies qu’avec un éclairage et une visibilité suff-isants. –

En hiver, prendre garde aux endroits glissants ou mouillés, à la glace et à la

neige (risque de glisser). Veiller à avoir toujours une bonne prise des pieds.

Ne jamais travailler sur une surface instable ou sur un terrain en pente. –

Ne jamais se tenir sur une échelle en manipulant la Taille - Haies. –

Ne jamais grimper dans les arbres pour procéder à des travaux de coupe –

avec la Taille - Haies.

Pour éviter de tomber et de perdre le contrôle de l’appareil, ne reculez jamais –

pendant son fonctionnernent.

Coupez toujours le moteur avant de nettoyer l’appareil on de remplacer –

certaines de ces pièces.

Ne faites jamais fonctionner le conpe-haies avec une lame endommagée ou –

trop usée.

Maintenance

Respectez l’environnement ; vériez notamment le bon réglage du –

carburateur pour polluer aussi peu que possible l’atmosphère.

Vériez régulièrement le Taille - Haies, et assurez - vous que ses vis et –

écrous sont bien xés.

Pendant toutes les opérations de maintenance ou de stockage,évitez –

soigneusement la présence de ammes, d’étincelles ou autres (11).

Stockez toujours l’appareil dans une pièce fermée â clé et bien aér’ee. Avant –

de le stocker, videz soigneusement son réservoir.

Necherchez pas à réparer l’appareil à moins d’être qualié pour le faire. –

Premiers secours

Pour être paré en cas d’accident, prévoir une trousse de premiers secours

bien fournie, et conforme à la norme DIN 13164, à proximité des opérations de

coupe. Remplacer immédiatement tout article pris dans la trousse de premiers

secours.

En cas d’accident, appeiez les services de secours et fournissez-leur les

informations suivantes :

Lieu de l’accident –

Circonstances de l’accident –

Nombre de personnes blessées –

Type de blessures –

Vos coordonnées –

Emballage

Le Taille - Haies DOLMAR est livré dans un carton qui le protège contre les

dommages pendant le transport. Le carton est une matière première de vase et

il peut être réutilisé ou recycié (recyclage des vieux papiers).

Respecteztoujourslesinstructionsdepréventiond’accidentsdesassociationsprofessionnellesetdescompagniesd’assurances.

Nemodiezpasl’appareil.

N’effectuez ancune opération de maintenance ou de réparation qui ne soit pas prévue par ce manuel. Toutes les autres opérations doivent être

effectuées par des représentants antorisés. N’utilisezque des pièces et des accessoires d’origine, fournis par DOLMAR.

L’utillsation d’outils et d’accessoires non agréés angrnente les risques d’accident. DOLMAR décline toute responsabilité en cas d’accident ou de

dommage provoqué par l’utilisation d’accessoires ou d’outils non agréés.

(10)

(11)

(12)

Downloaded from www.Manualslib.com manuals search engine

20

DONNÉES TECHNIQUES

Modèle HT-2576 E HT-2556 D

Dimensions : longueur x largeur x hauteur mm

(san lame de coupe) mm 1 041 × 280 × 258 840 × 246 × 225

Masse (sans protection en plastique et lame de coupe) kg 5,4 5,1

Volume (réservoir de carburant) cm3600

Cylindrée du moteur cm324,5

Longueur de coupe mm 750 560

Puissance maximale du moteur kw 0,88

Passes par minute min-1 4 180

Vitesse de marche à vide min-1 2 600

Vitesse d’embrayage min-1 3 600

Carburateur (carburateur à diaphragme) type WALBRO WYL

Systéme d’allumage type Type Allumage électronique

Bougie d’allumage type NGK-BMR7A

Ecartement entre les électrodes mm 0,6 - 0,7

Vibration selon la

norme ISO 22867

Poignée droite

(prise arrière)

ahv eq m/s26,1 11,1

Incertitude K m/s20,5 0,6

Poignée gauche

(prise avant)

ahv eq m/s212,6 12,1

Incertitude K m/s20,5 1,3

Niveau moyen de pression acoustique

selon la norme ISO 22868

LPA eq dB (A) 96,4 96,2

Incertitude K dB (A) 4,0 2,2

Niveau moyen de puissance

acoustique selon la norme ISO 22868

LWA eq dB (A) 106,4 103,6

Incertitude K dB (A) 1,7 2,1

Rapport du mélange (carburant : huile pour moteur 2 temps DOLMAR) 50 : 1

Rapport d’engrenages 14 : 58

1) Les caractéristiques prennent en comple tous les modes de fonctionnement: Vitesse de marche á vide, emballement et papillon des gaz

ouvert á fond

Pour les pays d’Europe uniquement

Déclaration de conformité CE

Nous, Makita Corporation, en tant que fabricant responsable, déclarons que la ou les machines Dolmar suivantes :

Nom de la machine : Taille-Haies

N° de modèle/Type : HT-2556 D, HT-2576 E

Spécications : reportez-vous au tableau « DONNÉES TECHNIQUES »

sont fabriquées en série et

sont conformes aux directives européennes suivantes :

2000/14/CE, 2006/42/CE

et sont produites conformément à la norme ou aux documents de normalisation suivants :

EN ISO 10517

La documentation technique est disponible auprès de :

Dolmar GmbH,

Jenfelder Straße 38, Abteilung FZ,

D-22045 Hamburg, Allemagne

La procédure d’évaluation de la conformité requise par la directive 2000/14/CE est conforme à l’annexe V.

HT-2556 D: Niveau de puissance sonore mesurée : 104,6 dB (A)

Niveau de puissance sonore garantie : 107 dB (A)

HT-2576 E: Niveau de puissance sonore mesurée : 107,3 dB (A)

Niveau de puissance sonore garantie : 109 dB (A)

3. 11. 2009

Tomoyasu Kato

Directeur

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, 446-8502, JAPAN

Downloaded from www.Manualslib.com manuals search engine

La pagina sta caricando ...

Dolmar HT-2556 D Manuale utente

Dolmar HT-2556 D Manuale utente

in altre lingue

Documenti correlati

Altri documenti