Candy CBT6130/3X Manuale utente

CBT6130/3X

Cooker Hood

Instruction Manual

ENGLISH(EN)------------------------------------------------------------------------------PAGE 001

FRENCH (FR)------------------------------------------------------------------------------PAGE 013

MAGYAR (HU) ---------------------------------------------------------------------------026. OLDAL

HRVATSKI (HR)---------------------------------------------------------------------STRANICA 038

PORTUGUÊS (PT) -----------------------------------------------------------------------PÁGINA 050

DEUTSCH (DE) ---------------------------------------------------------------------------- SEITE 062

ITALIANO (IT) ------------------------------------------------------------------------------PAGINA 074

Cooker Hood

Instruction Manual

Content

1…………………………………..………………………………Safety instructions

2…………………………………..………………………………Installation

3…………………………………..………………………………Start using your cooker hood

4…………………………………..………………………………Troubleshooting

5…………………………………..………………………………Maintenance and cleaning

6…………………………………..………………………………Environment protection

SAFETY INSTRUCTIONS

This manual explains the proper installation and use of your cooker hood,

please read it carefully before using even if you are familiar with the product.

The manual should be kept in a safe place for future reference.

These instructions shall also be available in an alternative format, e.g. on a

website or on request from the user in a format such as a DVD.

Never to do:

● D o not try to use the cooker hood

without the grease filters or if the filters

are excessively greasy!

●Do not install above a cooker with a

high level grill.

●Do not leave frying pans unattended

during use because overheated fats or

oils might catch fire.

●Never leave naked flames under the

cooker hood.

●If the cooker hood is damaged, do not

attempt to use.

●Do not flambé under the cooker hood.

●

CAUTION: Accessible parts may

become hot when used with cooking

appliances.

●

The minimum distance between the

supporting surface for the cooking

vessels on the hob and the lowest part

of the cooker hood. (When the cooker

hood is located above a gas appliance,

this distance shall be at least 65 cm)

●The air must not be discharged into a

flue that is used for exhausting fumes

from appliances burning gas or other

fuels.

Always to do:

● Important! Always switch off the

electricity supply at the mains during

installation and maintenance such as

light bulb replacement.

●The cooker hood must be installed in

accordance with the installation

instructions and all measurements

followed.

●All installation work must be carried

out by a competent person or qualified

electrician.

●Please dispose of the packing material

carefully. Children are vulnerable to it.

● P ay attention to the sharp edges

inside the cooker hood especially

during installation and cleaning.

●When the cooker hood is located

above a gas appliance,the minimum

distance between the supporting

surface for the cooking vessels on the

hob and the lowest part of the cooker

hood that distance must be:

Gas cookers: 75 cm

Electric cookers: 65 cm

Coal or oil cookers: 75 cm

●Make sure the ducting has no bends

sharper than 90 degrees as this will

reduce the efficiency of the cooker

hood.

●Warning: Failure to install the screws

or fixing device in accordance with

these instructions may result in

electrical hazards

●Warning: Before obtaining access to

terminals, all supply circuits must be

disconnected.

Always to do:

●Always put lids on pots and pans

when cooking on a gas cooker.

●When in extraction mode, air in the

room is being removed by the cooker

hood. Please make sure that proper

ventilation measures are being

observed. The cooker hood removes

odours from room but not steam.

●Cooker hood is for domestic use only.

●If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualified

persons in order to avoid a hazard.

●This appliance can be used by

children aged from 8 years and above

and persons with reduced physical,

sensory or mental capabilities or lack

of experience and knowledge if they

have been given supervision or

instruction concerning use of the

appliance in a safe way and

understand the hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

●Warning: Before obtaining access to

terminals, all supply circuits must be

disconnected.

Always to do:

● Caution: The appliance and its

accessible parts can become hot

during operation. Be careful to avoid

touching the heating elements.

Children younger than 8 years old

should stay away unless they are

under permanent supervision.

● There shall be adequate ventilation of

the room when the cooker hood is

used at the same time as appliances

burning gas or other fuels.

●There is a fire risk if cleaning is not

carried out in accordance with the

instructions

●Regulations concerning the discharge

of air have to be fulfilled.

●Clean your appliance periodically by

following the method given in the

chapter MAINTENANCE.

●For safety reason, please use only the

same size of fixing or mounting screw

which are recommended in this

instruction manual.

●Regarding the details about the

method and frequency of cleaning,

please refer to maintenance and

cleaning section in the instruction

manual.

●Cleaning and user maintenance shall

not be made by children without

supervision.

●When the cooker hood and

appliances supplied with energy other

than electricity are simultaneously in

operation, the negative pressure in the

room must not exceed 4 Pa (4 x 10-5

bar).

●WARNING: Danger of fire: do not

store items on the cooking surfaces.

●

A steam cleaner is not to be used.

●

NEVER try to extinguish a fire with

water, but switch off the appliance and

then cover flame e.g. with a lid or a

fire blanket.

INSTALLATION (VENT OUTSIDE)

MOUNTING OF THE V-FLAP（Optional）

If the cooker hood does not have an assembled V-flap 1, you should mount the half-

parts to its body. The images only show an example of how to mount the V-flap,the

outlet may be various according to different models and configuration.

To mount the V-flap 1 you should:

• Mount two half-parts 2 into the body 6

• a pin 3 should be top oriented;

• the axis 4 should be inserted in the holes 5 on body;

• repeat all the operations for the 2nd half-part

INSTALLATION (Wall Mounting)

1. Decide the location of the holes for fixing the cooker hood.

2. Install the L-shaped bracket on the top of the hood by two screws (4mm x 10mm)

3. The cooker hood is wall mounted by 4 screws (4mm x 30mm) and wall plugs.

Mount the cooker hood on the wall on the back of the cooker hood by 2 screws

(4mm x 30mm) and wall plugs. Then fix the cooker hood on the wall by 2 screws

(4mm x 30mm) and wall plugs through the small L-shaped bracket.

4. Fix the one-way-valve to the air outlet of the cooker hood.

INSTALLATION (Cabinet Mounting)

1. Fix the one-way-valve to the air outlet of the cooker hood.

2. Mount the cooker hood on the cabinet by 6 screws (4x35mm) and flat washers.

If there is gap between the wall and the cooker hood, you may install the L-shaped

bracket on the bottom of the hood by two screws (3 x 12mm).

The installation of the L-shaped bracket is optional.

Note: The expansion pipe is not included in the product.

WARNING:

 For safety reason, please use only the same

size of fixing or mounting screw which are

recommended in this instruction manual.

 Failure to install the screws or fixing device in

accordance with these instructions may result

in electrical hazards.

Start Using Your Cooker Hood

Rocker switch





Rockerswitch

1. Insert the power plug into the socket.

2. Push switch ① to , the lamp will be on; push switch ① to “0”, the lamp will

be off.

3. Push the switch ② into “I、II”, the motor will be on “low、high” two

speeds, push into “0”, the motor will be off.

4. The power will be connected when pull out the front panel. Conversely, the

power will be automatically disconnected.

TROUBLESHOOTING

Fault Possible Cause Solution

Light on, but motor

does not work

Fan switch turned off Select a fan switch position.

Fan switch failed Contact service center.

Motor failed Contact service center.

Light does not

work, motor does

not work

House fuses blown Reset/Replace fuses.

Power cord loose or

disconnected

Refit cord to power outlet.

Switch power outlet on.

Oil leakage

One way valve and the outlet

are not tightly sealed

Take down the one way valve

and seal with sealant.

Leakage from the connection of

chimney and cover

Take chimney down and seal.

Lights not working Broken/Faulty globes

Replace globes as per this

instruction.

Insufficient suction

The distance between the

cooker hood and the gas top is

too far

Refit the cooker hood to the

correct distance.

The Cooker hood

inclines

The fixing screw not tight

enough

Tighten the hanging screw and

make it horizontal.

NOTE:

Any electrical repairs to this appliance must conform to your local, state and

federal laws.Please contact the service centre if in any doubt before

undertaking any of the above.Always disconnect the unit from the power source when

opening the unit.

MAINTENANCE AND CLEANING

Caution:

• Before maintenance or cleaning is carried out, the cooker hood

should be disconnected from the main power supply. Ensure

that the cooker hood is switched off at the wall socket and the

plug removed.

• External surfaces are susceptible to scratches and abrasions, so please follow the

cleaning instructions to ensure the best possible result is achieved without damage.

GENERAL

Cleaning and maintenance should be carried out with the appliance cold especially

when cleaning.Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on

the surfaces.

STAINLESS STEEL

The stainless steel must be cleaned regularly (e.g.weekly) to ensure long life

expectancy.Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may

be used.

NOTE:

Ensure that wiping is done along with the grain of the stainless steel to prevent any

unsightly crisscross scratching patterns from appearing.

CONTROL PANEL SURFACE

The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is

clean and well wrung before cleaning. Use a dry soft cloth to remove any excess

moisture left after cleaning.

Important

Using neutral detergents and avoid using harsh cleaning chemicals, strong household

detergents or products containing abrasives,as this will affect the appliance

appearance and potentially remove any printing of artwork on the control panel and

will void manufactures warrantee.

GREASE MESH FILTERS

The mesh filters can be cleaned by hand. Soak them for about 3 minute in water with a

grease-loosening detergent then brush it gently with a soft brush. Please do not apply

too much pressure, avoid to damage it . (Leave to dry naturally out of direct sun light)

Filters should be washed separately to crockery and kitchen utensils. it is advisable

not to use rinse aid.

INSTALLING GREASE MESH FILTERS

• To install filters for the following four steps .

- Angle the filter into slots at the back of the hood.

- Push the button on handle of the filter.

- Release the handle once the filter fits into a resting position.

- Repeat to install all filters.

CARBON FILTER

Activated carbon filter can be used to trap odors. Normally the activated carbon filter

should be changed at three or six months according to your cooking habit. The

installation procedure of activated carbon filter is as below.

1. Put the carbon filter on the back side of the aluminium filter.

2. Insert the steel wire into the frame of the aluminium filter, one on each side. You

need to bend it to insert into the other end of the frame.

3. Make sure the steel wire fix the carbon filter onto the aluminium filter.

NOTE:

 Make sure the filter is securely locked. Otherwise, it would loosen and cause

dangerous.

 When activated carbon filter attached, the suction power will be lowered.

BULB REPLACEMENT

Important :

 The bulb must be replaced by the manufacturer, its

service agent or similarly qualified persons.

 Always switch off the electricity supply before

carrying out any operations on the appliance. When

handling bulb, make sure it is completely cool down

before any direct contact to hands.

 When handling globes hold with a cloth or gloves to

ensure perspiration does not come in contact with

the globe as this can reduce the life of the globe.

Changing the light

Use the screw driver loosen the ST4*8MM self tapping screw (2pcs) from the lighting

panel, take out the lighting fixture. Open the terminal box that connected with the wire,

disconnect the wire connector and replace the lamp.

• ILCOS D code for this lamp is: DBS-2/65-H-120/33

– LED modules –rectangle lamp

– Max wattage: 1X2 W

– Voltage range: AC 220-240V

– Dimensions:

ENVIRONMENTAL PROTECTION:

This product is marked with the symbol on the selective sorting of

waste electronic equipment. This means that this product must not

be disposed of with household waste but must be supported by a

system of selective collection in accordance with Directive

2012/19/EU. It will then be recycled or dismantled to minimize

impacts on the environment, electrical and electronic products are

potentially dangerous for the environment and human health due to

the presence of hazardous substances.For more information, please

contact your local or regional authorities.

NOTE:

The following shows how to reduce total environmental impact (e.g. energy use) of the

cooking process).

(1) Install the cooker hood in a proper place where there is efficient ventilation.

(2) Clean the cooker hood regularly so as not to block the airway.

(3) Remember to switch off the cooker hood light after cooking.

(4) Remember to switch off the cooker hood after cooking.

INFORMATION FOR DISMANTLING

Do not dismantle the appliance in a way which is not shown in the user manual. The

appliance could not be dismantled by user. At the end of life, the appliance should

not be disposed of with household waste. Check with you Local Authority or retainer

for recycling advice.

Hotte aspirante

Manuel d’instruction

Sommaire

1…………………………………..………………………………Consignes de sécurité

2…………………………………..………………………………Installation

3…………………………………..………………………………Commencez à utiliser votre hotte aspirante

4…………………………………..………………………………Dépannage

5…………………………………..………………………………Entretien et nettoyage

6…………………………………..………………………………Protection de l’environnement

CONSIGNES DE SÉCURITÉ

Ce manuel explique comment installer et utiliser correctement votre hotte aspirante.

Veuillez le lire attentivement avant toute utilisation même si vous connaissez bien le

produit. Le manuel doit être conservé en lieu sûr pour pouvoir le consulter en cas de

besoin.

À ne jamais faire :

● Ne tentez pas d’utiliser la hotte aspirante

sans les filtres à graisse ou si les filtres

sont excessivement encrassés !

●

Ne l’installez jamais au-dessus d'une

cuisinière avec un gril placé en hauteur.

●

Ne laissez pas les poêles à frire sans

surveillance pendant leur utilisation car les

huiles ou les graisses surchauffées

pourraient prendre feu.

●

Ne laissez jamais des flammes nues sous

la hotte aspirante.

●

Si la hotte aspirante est endommagée,

n’essayez pas de l’utiliser.

●

Ne flambez rien sous la hotte aspirante.

●

ATTENTION : Les parties accessibles

peuvent devenir chaudes lors de

l’utilisation avec des appareils de cuisson.

●

La distance minimale entre la surface de

support pour les récipients de cuisson sur

la plaque de cuisson et la partie la plus

basse de la hotte aspirante. (Quand la

hotte aspirante est située au-dessus d’une

cuisinière à gaz, cette distance doit être

d’au moins 65 cm)

●

L’air ne doit pas être évacué dans un

conduit utilisé pour les fumées provenant

d’appareils de combustion à gaz ou

fonctionnant avec d’autres

carburants.

À toujours faire :

● Important ! Coupez toujours l’alimentation

électrique durant l’installation et l’entretien,

comme par exemple quand vous changez

une ampoule.

●

La hotte aspirante doit être installée

conformément aux instructions

d’installation et toutes les mesures doivent

être respectées.

●

Tout le travail d’installation doit être

effectué par une personne compétente ou

un électricien qualifié.

●

Veuillez faire attention quand vous jetez

l’emballage. Les enfants pourraient se

blesser avec.

●

Faites attention aux bords coupants à

l'intérieur de la hotte aspirante durant

l’installation et le nettoyage.

●

Quand la hotte aspirante est située au-

dessus d’une cuisinière, la distance

minimale entre la surface de support pour

les récipients de cuisson sur la plaque de

cuisson et la partie la plus basse de la

hotte aspirante doit être la suivante :

Cuisinières à gaz : 75 cm

Cuisinières électriques : 65 cm

Cuisinières à charbon ou à mazout : 75 cm

●

Vérifiez que les coudes des conduits ne

sont pas inférieurs à 90 degrés car cela

réduirait l’efficacité de la hotte aspirante.

●Avertissement : Si les vis ou le

dispositif de fixation ne sont pas

installés conformément à ces

instructions, cela peut provoquer des

dangers électriques

À toujours faire :

●Placez toujours le couvercle sur les

casseroles et les poêles quand vous

cuisinez sur une cuisinière à gaz.

●

En mode extraction, l’air de la pièce est

éliminé par la hotte aspirante. Vérifiez que

des mesures de ventilation correctes sont

adoptées. La hotte aspirante élimine les

odeurs de la pièce mais pas la vapeur.

●

La hotte aspirante est réservée à un usage

domestique.

●

Si le cordon d’alimentation est endommagé,

faites-le remplacer par le fabricant, le

service après-vente ou un électricien

qualifié pour éviter tout risque d’accident.

●

Cet appareil peut être utilisé par des

enfants âgés de 8 ans et plus et par des

personnes à capacités physiques,

sensorielles ou intellectuelles réduites ou

sans expérience et connaissances, s'ils

sont sous une surveillance appropriée ou

bien s'ils ont été informés quant à

l'utilisation de l'appareil de manière sûre,

et s'ils comprennent les risques impliqués.

Les enfants ne doivent pas jouer avec

l'appareil. Le nettoyage et l’entretien ne

doivent pas être effectués par des enfants

sans surveillance.

●Avertissement : Avant d’accéder aux

bornes, il faut débrancher tous les

circuits d’alimentation.

À toujours faire :

● Attention : L’appareil et ses parties

accessibles peuvent devenir chauds

durant le fonctionnement. Évitez de

toucher les éléments qui chauffent. Les

enfants âgés de moins de 8 ans doivent

rester à distance à moins d’être surveillés

en permanence.

●

Il faut disposer d’une ventilation

appropriée dans la pièce où la hotte

aspirante est utilisée en même temps que

d’autres appareils brûlant du gaz ou

d’autres carburants.

●

Il existe un risque d'incendie si le nettoyage

n’est pas effectué conformément aux

instructions.

●

Les réglementations relatives à

l’évacuation de l’air doivent être

respectées.

●

Nettoyez régulièrement votre appareil en

suivant la méthode fournie dans le

chapitre ENTRETIEN.

●

Pour des raisons de sécurité, veuillez

n’utiliser que des vis de fixation ou de

montage de la même taille que celle

recommandée dans ce manuel

d’instruction.

●

En ce qui concerne les détails sur la

méthode et la fréquence de nettoyage,

veuillez vous reporter au paragraphe

relatif à l’entretien et au nettoyage dans le

manuel d’instruction.

●

Le nettoyage et l’entretien ne doivent pas

être effectués par des enfants sans

surveillance.

●

Quand la hotte aspirante et les appareils

alimentés par autre chose que de

l’électricité fonctionnent simultanément, la

pression négative à l’intérieur de la pièce

ne doit pas dépasser 4 Pa (4 x 10-5 bar).

●

AVERTISSEMENT : Risque d’incendie : ne

rangez aucun objet sur les surfaces de

cuisson.

●

Il ne faut pas utiliser de nettoyeur vapeur.

●

Ne tentez JAMAIS d’éteindre un incendie

avec de l’eau, mais éteignez l’appareil

puis couvrez la flamme par exemple avec

un couvercle ou une couverture pare-

flammes.

INSTALLATION (ÉVENT À L’EXTÉRIEUR)

MONTAGE DU RABAT EN V（Optionnel）

Si la hotte aspirante n’a pas de rabat en V 1 monté, vous devez monter les moitiés sur

son corps. Les images ne montrent qu’un exemple de la façon de monter le rabat en V,

la sortie peut varier en fonction des modèles et de la configuration.

Pour monter le rabat en V 1, vous devez :

• Monter deux moitiés 2 dans le corps 6 ;

• Une cheville 3 doit être dirigée vers le haut ;

• L’axe 4 doit être introduit dans les trous 5 sur le corps ;

• Répétez toutes les opérations pour la seconde moitié.

INSTALLATION (murale)

1. Choisissez l’emplacement des trous pour fixer la hotte aspirante.

2. Installez l’étrier en L sur le dessus de la hotte avec deux vis (4 mm x 10 mm).

3. La hotte aspirante est fixée au mur par 4 vis (4 mm x 30 mm) et des chevilles.

Fixez la hotte aspirante sur le mur au niveau de l’arrière de la hotte aspirante avec

2 vis (4 mm x 30 mm) et des chevilles. Puis fixez la hotte aspirante sur le mur avec

2 vis (4 mm x 30 mm) et des chevilles à travers le petit étrier en L.

4. Fixez le clapet anti-refoulement sur la sortie d’air de la hotte aspirante.

INSTALLATION (sur un meuble)

1. Fixez le clapet anti-refoulement sur la sortie d’air de la hotte aspirante.

2. Montez la hotte aspirante sur le meuble avec les 6 vis (4x35 mm) et les rondelles

plates.

La pagina sta caricando ...

Candy CBT6130/3X Manuale utente

Questo manuale è adatto anche per

Candy CBT6130/3X Manuale utente

in altre lingue

Documenti correlati

Altri documenti