Grant Instruments Optima T100 Heated Circulating Bath Istruzioni per l'uso

FR

EN

DE

IT

ES

General purpose

immersion thermostats,

baths & circulators

Optima T100 & TC120

Operating Manual

Grant Instruments, based near Cambridge, England is a world leader in the

manufacture and design of equipment for sample preparation, scientific analysis, data

acquisition and data analysis providing solutions to the global scientific and industrial

markets.

Standards Compliance and Quality

Grants’ brand and reputation are based around quality, reliability and accuracy. We

ensure our products stringently meet all necessary international safety standards.

We pay particular attention to the safety testing of products and remain at the forefront of

the product safety standard for laboratory equipment IEC 61010-1. The company is

committed to operating its safety test laboratory in accordance with the requirements of

ISO 17025.

Grant operates a Quality Management System that complies with the requirements of BS

EN ISO 9001:2008.

Beyond compliance to the standard, Grant is committed to continually improving in

everything we do; with particular emphasis on understanding what matters to our

customers and suppliers, and designing our systems and work to meet their needs.

If you have any feedback on Grant’s products or services we would like to hear from you.

Please send all feedback to:

Quality Manager

Grant Instruments (Cambridge) Ltd

Shepreth

Cambridgeshire

SG8 6GB

UK

Tel: +44 (0) 1763 260 811

Fax: +44 (0) 1763 262 410

E-mail: feedback@grantinstruments.com

T100 & TC120 30423 V4

Operating Manual Page 2

www.grantinstruments.com

EN

Contents

Contents 2

1.0 Use of products 4

2.0 How to use this operating manual 4

3.0 Safety information 5

3.1 Safety compliance 5

3.2 Safety symbols 5

3.3 Safety warnings 5

4.0 Operating instructions 6

4.1 Unpacking instructions 6

4.2 Fitting controller to ST baths 6

4.3 Fitting the controller to P baths 7

4.4 Fitting the controller to custom baths 7

4.5 Removing the controller from the bridge plate 8

4.6 Recommended liquids 8

4.7 Installation 9

4.8 Electrical supply 9

4.9 Using accessory cooling (C1G, C2G, CW5) 9

5.0 Operating procedures 10

5.1 Operation 10

5.1.1 Liquid level 10

5.1.2 Operation above 60°C 10

5.1.3 Operation at low temperatures 10

5.1.4 Using the pump (TC120 only) 10

5.1.5 Emptying the ST baths 11

5.1.6 Setting up and switching on 11

5.2 Using the T100 & TC120 12

5.2.1 Product description 12

5.2.2 Product indicators 12

5.2.3 Setting the control temperature 13

5.2.4 Configuring a preset 13

5.2.5 Running a bath preset 13

5.2.6 Completing a calibration 14

5.2.7 Restoring factory calibration settings 15

5.2.8 Adjusting display brightness 15

5.3 Additional features of the TC120 16

5.3.1 Setting the over-temperature thermostat 16

5.3.2 Setting a countdown timer 16

5.3.3 Cancelling the timer 17

5.3.4 Setting a high temperature warning alarm 17

5.3.5 Selecting liquid type 17

6.0 Technical specifications 18

6.1 Operating conditions 18

6.2 Electrical details 18

6.3 Product performance 18

6.4 Bath accessories information 18

7.0 Technical Tips 19

7.1 Which water should you use in your bath? 19

7.2 How to prevent rust in water baths 19

7.3 How to prevent algae and bacteria? 19

8.0 Warranty information 20

9.0 Maintenance and service 20

9.1 Routine Maintenance 20

9.2 Cleaning 20

30423 V4 T100 & TC120

Page 3 Operating Manual

www.grantinstruments.com

9.3 Fuses 21

9.4 Routine safety tests 21

9.5 Service 21

10.0 Optional accessories 21

11.0 Troubleshooting 22

12.0 Contact Grant Instruments 24

13.0 Compliance 24

T100 & TC120 30423 V4

Operating Manual Page 4

www.grantinstruments.com

EN

1.0 Use of products

The following products are covered by this operating manual:

 T100 & T100L

 TC120 & TC120L

The products listed above are general purpose immersion thermostats to be used with

baths or circulators designed for indoor laboratory use by a professional user.

2.0 How to use this operating manual

This operating manual will allow you to unpack, set-up and operate this immersion

thermostat correctly and safely. Important safety information, symbols and warnings are

listed below and should be read carefully. Section 4 gives information about how to

unpack and install the product correctly. Section 5 gives operating information for the

T100 & TC120 models. Product technical specifications and tips are provided in sections

6 and 7. The warranty for this product is for THREE YEARS and is detailed in section 8

and should be registered by completing the on-line registration form at

www.grantinstruments.com.

If there is a technical matter that this operating manual does not address, or any other

question concerning this product, please contact Grant Instruments or your local

distributor, who will be able to provide any additional information.

A quick start guide is provided with the T100/TC120 immersion thermostats as a

reference guide but should not be used until the full user manual has been read.

30423 V4 T100 & TC120

Page 5 Operating Manual

www.grantinstruments.com

3.0 Safety information

3.1 Safety compliance

Grant immersion thermostats meet the requirements of international safety standard

IEC 61010: Safety requirements for electrical equipment for measurement, control, and

laboratory use. They also comply with the equivalent national standards including:

EN 61010-2-010

UL 61010A-2-010

CAN/CSA-C22.2 NO. 61010-2-010-04.

3.2 Safety symbols

The symbols below are marked on the equipment and throughout this manual to indicate:

Caution: Surfaces and heat transfer liquid can be hot during and after use.

Read this manual before using the bath.

Important safety warning.

3.3 Safety warnings

Read the whole of these instructions. Safety may be impaired if they are not

followed.

For the T100, only use water as the working liquid.

For the TC120, only use liquids specified in these operating instructions, within

the specified temperature range. If the alarm lamp is illuminated the liquid

temperature may be above its recommended maximum. Do not inhale the

vapours given off as they may be toxic. Liquids should be safely discarded and

replaced.

Do not use the T100/TC120 with flammable heat transfer liquids.

Do not use the T100/TC120 to heat any sample material that could cause a fire

or any other kind of hazard.

Do not use the equipment in an area where there are aggressive or explosive

chemical mixtures.

If a potentially hazardous liquid is spilt onto or inside the equipment, disconnect

it from the power supply and have it checked by a competent person.

It is the user’s responsibility to carry out appropriate decontamination if

hazardous material is spilt on the equipment.

If the alarm lamp is illuminated do not touch the liquid or the tank base, they

may be very hot. Refill carefully, a hot heater can cause a spattering of very hot

water droplets and scalding steam.

Do not touch surfaces which become hot during high temperature operation.

T100 & TC120 30423 V4

Operating Manual Page 6

www.grantinstruments.com

EN

4.0 Operating instructions

4.1 Unpacking instructions

Standard equipment includes:

 Immersion thermostat (T100 or TC120)

 Pump outlet plates (TC120 only)

 Mains cord with plug

 Operating manual

 Quick start guide

ST bath accessory includes:

 Stainless steel bath

 Bridge plate

 Circulating tray (ST18, ST26 & ST38 baths only)

P bath accessory includes:

 Plastic bath

 Bridge plate

Remove packing materials carefully and retain them for future shipment or storage of the

equipment.

4.2 Fitting controller to ST baths

The T100/TC120 can be fitted to the following stainless steel baths, ST5, ST12, ST18,

ST26 and ST38 in two orientations for convenience, facing over ST bath (A) or facing

outwards (B):

1. Fit the T100/TC120 through the hole in the bridge plate and align using the locating

threads. Secure using the retaining nuts. Hand tighten only.

2. Hook the assembly into the slots on the ST bath and use the supplied fixing to secure

to the rear of the bath.

2

A

B

1

2

30423 V4 T100 & TC120

Page 7 Operating Manual

www.grantinstruments.com

Fit the circulation tray in the base of the tank with the large cut out in the tray underneath

the control unit (ST18, ST26 & ST38 only).

4.3 Fitting the controller to P baths

The T100/TC120 can be fitted to the following plastic baths, P5, P12 and P18:

1. Fit the T100/TC120 through the hole in the bridge plate and align using the locating

threads. Secure using the retaining nuts. Hand tighten only.

2. Add the assembly to the P bath and use the supplied fixing to secure to the rear of

the bath.

4.4 Fitting the controller to custom baths

A clamp can be fitted to the T100/TC120 to allow attachment to a non-Grant bath or

vessel with a wall thickness of up to 30mm. To fit the clamp to the T100/TC120:

1. Place clamp over locating threads on base of T100/TC120. Secure using the

retaining nuts. Hand tighten only.

2. Add clamp rear fixings to secure to rear of T100/TC120.

Take care not to over tighten the clamp to avoid damaging the clamp or vessel

The liquid container on which the unit is mounted must be stable and have the

necessary robustness, mechanical, chemical and heat resistance.

Do not wash the clamp in a dishwasher or clean it with descaler. Do not submerse the

threaded shaft of the clamp. Always dry the threaded shaft and clamp after cleaning.

The threads may be lubricated with a small amount of light machine oil.

1

2

1

2

T100 & TC120 30423 V4

Operating Manual Page 8

www.grantinstruments.com

EN

4.5 Removing the controller from the bridge plate

Allow the working liquid to cool before removing the T100/TC120 from the bridge plate.

Carefully remove the T100/TC120 and bridge plate together from the bath or vessel.

Take care as the pump will contain a small amount of the working liquid which will leak

out as the unit is handled. Undo the retaining nuts and remove the bridge plate. Attach

the retaining nuts to the locating threads for safe keeping.

4.6 Recommended liquids

The following table lists the recommended liquids for different temperature ranges.

Always ensure the liquid used is safe and suitable for your working temperature. If using

non-recommended heat transfer liquids, it is the responsibility of the user to conduct an

assessment to ensure the intended fluid is compatible with the T100/TC120 and vessel.

If using non-recommended heat transfer liquids it is important to set the over-temperature

cut-out to a value no higher than 25°C below the fire point of the liquid. If in doubt please

contact the Grant technical support team.

To ensure protection the overtemperature cut out (TC120 only) must be set

appropriately for the heat transfer liquid selected. See table below.

If using non-recommended heat transfer liquids it is important to set the over-

temperature cut-out to a value no higher than 25°C below the fire point of the

liquid. If in doubt please contact the Grant technical support team.

Use fume extraction when using silicone fliuids at elevated temperatures

Temp range

Recommended

liquid

Cut-out

setting

Comments

-30°C to 30°C

50% water, 50%

antifreeze (inhibited

ethylene glycol)

40°C

WARNING: Ethylene glycol is

toxic – follow the manufacturer’s

instructions.

For safe disposal consult your

local regulations.

Use a lid to reduce the dilution

of the mixture caused by

condensing water vapour from

the air, and to maintain the cool

down rate.

0°C to 30°C

80% water, 20%

antifreeze (inhibited

ethylene glycol)

40°C

5°C to 99.9°C

Water*

110°C

Water can be used but care

should be taken above 60°C as

hot vapour can be dangerous.

Use a lid or polypropylene

spheres above 60°C to ensure

good performance & reduce

evaporation.

At temperatures approaching

99°C the temperature

performance will be affected due

to localised boiling.

The units should not be used to

boil water.

30423 V4 T100 & TC120

Page 9 Operating Manual

www.grantinstruments.com

Temp range

Recommended

liquid

Cut-out

setting

Comments

70°C to 120°C

Silicone fluid

Viscosity ~20cs

Flash point ≥230°C

Fire Point ≥280°C

130°C

Dow Corning DC200/20 silicone

fluid is a suitable liquid – follow

the manufacturer’s instructions.

For safe disposal consult your

local regulations.

* See section 7.1 for further details

4.7 Installation

Place the water bath on a level, non-combustible surface. Ensure that the

mains plug and the switch at the rear of the unit are easily accessible.

If the equipment has been transported or stored in cold or humid conditions,

condensation may form inside it. If that could have happened, allow time (at

least 2 hours at room temperature) for the condensation to evaporate before

using the equipment.

Do not block or restrict ventilation slots.

4.8 Electrical supply

Check that the supply voltage marked on the serial number label, and the type

of mains plug, are correct for your mains supply outlet, which must have a

ground connector.

The T100/TC120 must only be connected to the mains using the mains cord

supplied or one with an identical rating (see section 9.4)

4.9 Using accessory cooling (C1G, C2G, CW5)

Accessory cooling is required for operation at temperatures below ambient. Refrigerated

dip coolers (C1G and C2G) can be used for operation down to -15°C. A water heat

exchanger coil (CW5) can be used for operation at or around ambient. The coils can be

fitted:

1. Attach u-shaped coil locating rod to cover plate using two fixings supplied.

2. Fit the cooling coil through the hole in the bridge plate and align outlet pipes with cut-

out notch.

3. Fit cover plate onto bridge plate and attach with fixings supplied. The coil locating

rod should press fit against the inside of the coil and hold it rigidly. Ensure the coil is

held safely and securely before operation.

2

1

3

CW5

C1G & C2G

2

1

3

T100 & TC120 30423 V4

Operating Manual Page 10

www.grantinstruments.com

EN

5.0 Operating procedures

5.1 Operation

5.1.1 Liquid level

The minimum and maximum liquid levels are defined in section 6.4 for Grant accessory

baths. Liquid level should always be maintained between these levels. These levels

apply both when there are no vessels in the bath and with the maximum contents. If

using liquids that can evaporate then periodic checking and refilling should be completed.

The low level float switch will alarm if the liquid level drops below the minimum required

level and the unit will switch off the heater and stop temperature control.

5.1.2 Operation above 60°C

A lid or polypropylene spheres must be used above 60°C to maintain temperature control

and to ensure that the bath fluid temperature reaches the set point. They will save

energy by preventing excessive evaporation and reduce the frequency that the bath

needs to be refilled. As a precaution, the T100/TC120 may display ‘Hot’ if heating water

at or near boiling over extended periods or heating large volumes of liquid with large

thermal losses without the use of a lid or polypropylene spheres. See section 11 for

additional guidance.

Care should be taken to ensure rear inlet vents are clear and minimise the intake of

steam when operating at or near boiling water or with other evaporating liquids.

Take care when lifting and removing the lid as it may be hot. Steam and hot

vapours can cause scalding.

5.1.3 Operation at low temperatures

Accessory cooling is required for controlled operation at or below ambient temperature.

The minimum working temperature without accessory cooling depends on the size of the

bath. The small baths, P5 and ST5, have a minimum working temperature of

approximately 10°C above ambient without a lid and 15°C above ambient with a lid.

Other bath sizes can be used at a temperature of 5°C above ambient.

5.1.4 Using the pump (TC120 only)

The TC120 allows liquid to be pumped around a closed external system (not open to the

atmosphere). It may be used for circulation through an external open tank only if a

gravity feed return is present. An assessment of any reservoir running should be

completed to ensure liquid levels are stable during operation and there is no chance of

any resevoir running dry or overflowing. The pump is fitted with a blanking plate as

standard. Fit a pump connector plate as shown below. Note: the blanking/connector

plates have a locating hole (see A below) to assist correct alignment onto the pump

moulding. It is important to verify the hole is aligned with the corresponding locating pin

(see B below) on the pump moulding. Failure to do so will result in a leaking connection.

Retain the blanking plate for refitting when the pump is no longer required.

Always use pump connectors and hoses that are suitable for the operating

temperature and liquid used. Check the pipe connections are secure.

Never disconnect any pipes or hoses while they contain very hot or very cold

liquids or while the TC120 is pumping.

30423 V4 T100 & TC120

Page 11 Operating Manual

www.grantinstruments.com

Pumping heat transfer liquid around an external system can lead to hazards that are

outside the control of Grant Instruments. It is essential that the user conducts a risk

assessment of the entire equipment installation to ensure that correctly rated materials

have been used throughout and that the system can be used safely.

5.1.5 Emptying the ST baths

The ST12, ST18, ST26 & ST38 baths should be emptied to a safe level prior to moving.

A drain tap is included on these baths to allow convenient emptying.

Allow the liquid temperature to fall to a safe level before emptying. If the bath is drained

at temperatures above 50°C then the drain mechanism will be damaged and will need to

be replaced. Take reasonable precautions to prevent accidental spillage.

Empty the bath by pushing the supplied drain insert into the drain tap as shown below.

Note that the bath liquid will begin to empty as soon as the drain insert is fully engaged.

A length of hose can be added to the barbed end of the drain insert if required.

5.1.6 Setting up and switching on

Connect the T100/TC120 to a grounded (earthed) electrical power supply with voltage

and frequency within the range specified on the serial number plate.

Attach the T100/TC120 securely to the required bath or vessel. Add the appropriate

working liquid to the bath to at least the minimum recommended fill level such that the

float level switch is fully raised.

Switch on the T100/TC120 using the power switch on the rear of the unit. The motor will

start immediately and the buzzer will sound while the unit starts up. During start up the

display will show the model type, followed by the software version and finally the current

liquid temperature. The T100/TC120 is ready to use.

To disconnect the equipment from the mains supply, remove the mains plug from the

mains supply outlet.

B

A

T100 & TC120 30423 V4

Operating Manual Page 12

www.grantinstruments.com

EN

5.2 Using the T100 & TC120

5.2.1 Product description

5.2.2 Product indicators

There are two indicator lights on the T100/TC120:

 Heater on light (orange) marked

 Alarm light (red) marked

The alarm lamp will light to indicate the following faults:

 Float switch has operated due to low liquid level

 Over-temperature cut out has operated

 Temperature probe fault

The cause of the alarm will also be shown on the display.

The display normally shows the temperature in °C of liquid being controlled.

The S(elect) button is used to select and store values whilst the F(unction) button is used

to access menu options and cancel functions.

The main dial is used to change temperature values and other settable parameters.

Float switch

Display

Alarm light

Control dial

Heater on light

Pump outlet plate

(TC120 only)

Over-temperature dial

(TC120 only)

Select button

Function button

30423 V4 T100 & TC120

Page 13 Operating Manual

www.grantinstruments.com

5.2.3 Setting the control temperature

The temperature of the bath liquid can be set using the S button.

1. Whilst the display is showing the bath temperature, press the S button. This will

cause the display to flash indicating that it can be set.

2. Use the main dial to set the desired temperature.

If no key is pressed for 10 seconds then the display will revert back to showing the

bath temperature and the set temperature will remain at its original value.

3. Press the S button to store the requested value and the display will revert to showing

the bath temperature.

If the temperature selected is higher than the current liquid temperature, the heater

light will come on.

5.2.4 Configuring a preset

Each T100/TC120 contains three presets which can be configured to different set

temperatures to allow the bath to be conveniently run at frequently used temperatures.

Use the method below to configure preset 1; other presets can be set in a similar

manner.

Be aware that once a preset has been saved using the steps below, it will automatically

start once all the steps have been completed.

1. Press the F button and rotate the dial until the display shows “t-1”.

The display will alternate between the preset number and its temperature.

2. Press the S button to select the preset.

3. Use the dial to set the desired preset temperature.

If no key is pressed for 10 seconds then the display will revert back to showing the

bath temperature and the preset temperature will remain at its original value.

4. Press the S button to save the preset temperature.

The preset will automatically start as soon as the value is saved.

Preset temperatures and set temperatures are limited to the model type and the liquid

selection. The T100 settable range is between 0 and 100°C increasing to between -25°C

and 120°C for the TC120. The factory preset settings are shown in the table below.

Preset

Set temperature range

t-1

37°C

t-2

56°C

t-3

72°C

5.2.5 Running a bath preset

1. Press the F button and rotate the dial until the display shows the correct preset.

2. Press the S button to select the preset.

3. Press the S button to set the bath to the preset temperature.

T100 & TC120 30423 V4

Operating Manual Page 14

www.grantinstruments.com

EN

5.2.6 Completing a calibration

The T100 & TC120 allow a two point calibration to be completed. The calibration menu

can be accessed by simultaneously pressing the F and S buttons for about 5 seconds.

The calibration temperatures are constrained by the temperature limits of the liquid type

setting. Calibration should be carried out using a traceable reference thermometer with

an accuracy of at least 0.1°C. This thermometer should be held securely in the centre of

the bath or vessel.

The calibration of the T100/TC120 is in two parts, a low temperature offset and a high

temperature offset. The high temperature calibration point must be at least 40°C higher

than the low temperature point.

Calibration points should be chosen to be at critical experimental temperatures where

accuracy is important or at the extremes of the working range of used temperatures.

If only the low temperature calibration point is set then the calibration will be performed

between this point and 100°C with the offset decreasingly linearly. If only the high

temperature calibration point is set then the calibration will be performed between 0°C

and this point with the offset decreasingly linearly.

If the thermometer value is entered before the unit is completely stable then the

calibration could be poor and liquid temperature readings will be incorrect. If the

T100/TC120 is not in accordance with the thermometer following calibration then it may

not have been successful and the unit should be reset.

Setting the low temperature offset

1. Adjust the set temperature to the required low temperature calibration point.

2. Allow the unit to stabilise for at least 5 minutes after a stable temperature condition

has been achieved.

3. Measure the liquid temperature by placing a reference thermometer into the centre of

the bath.

4. Press the F and S buttons simultaneously for approximately 5 seconds until “LCAL” is

shown.

5. Press the S button to select.

6. Use the main dial to update the display to show the temperature on the reference

thermometer.

7. Press the S button to store the temperature.

Press the F button to cancel the calibration.

8. Press the F button to return to the liquid temperature display.

Setting the high temperature offset

1. Adjust the set temperature to the required high temperature calibration point.

2. Allow the unit to stabilise for at least 5 minutes after a stable temperature condition

has been achieved.

3. Measure the liquid temperature by placing a reference thermometer into the centre of

the bath.

4. Press the F and S buttons simultaneously for approximately 5 seconds until “LCAL” is

shown.

5. Rotate the dial until the display shows “HCAL” and press the S button to select.

6. Use the main dial to update the display to show the temperature on the reference

thermometer.

7. Press the S button to store the temperature.

Press the F button to cancel the calibration.

30423 V4 T100 & TC120

Page 15 Operating Manual

www.grantinstruments.com

5.2.7 Restoring factory calibration settings

The restore factory calibration allows the unit settings to be reset if there is a problem

during calibration or you wish to cancel any of the calibration settings.

1. Press the F and S buttons simultaneously for approximately 5 seconds until “LCAL” is

shown.

2. Rotate the dial until the display shows “rST” and press the S button to select.

3. Press the S button four times (the display will show “Con.3”, “Con.2”, Con.1” and

sound the buzzer to confirm the factory reset has been completed.

5.2.8 Adjusting display brightness

The brightness of the display can be adjusted over a limited range (20% to 100%) if

required.

1. Press F and S buttons simultaneously for approximately 5 seconds until the display

shows “LCAL”.

2. Rotate the dial until the display shows “disP” and press the S button to select.

3. Rotate the dial between the settings and select required brightness

The displayed values show the display brightness

4. Press S button to save the value.

5. Press F button to return to the normal temperature display.

T100 & TC120 30423 V4

Operating Manual Page 16

www.grantinstruments.com

EN

5.3 Additional features of the TC120

5.3.1 Setting the over-temperature thermostat

An over-temperature cut-out dial with a temperature scale is located at the top right of the

unit. The over-temperature probe independently monitors the bath temperature and

switches the heater off if it goes above the cut-out threshold. The T100 temperature cut-

out threshold is fixed at 110 °C. For the TC120, the temperature cut-out threshold can

be adjusted for convenience.

Coarse setting of the over-temperature thermostat

Rotate the temperature cut-out dial in line with the marked scale to the desired setting.

This should be higher than the set temperature to avoid operating the cut-out before the

set temperature has been reached.

If the alarm is triggered, it can be cancelled by pressing either the F or S button once.

The unit must then be switched off to clear the cut-out alarm. To continue to use the

TC120, let the bath liquid cool by at least 5°C either naturally or by replacing the liquid,

switch the unit off, wait 10 seconds and switch it on again to clear the alarm. To avoid

nuisance tripping the trip point needs to be set at least 5°C above the desired control

temperature.

Alternative setting of the over-temperature thermostat

Rotate the temperature cut-out dial to maximum (or at least a value above the level

required) and configure the set temperature to the cut-out level required. Leave the bath

to reach the set temperature and stabilise for at least 5 minutes. Turn the cut-out dial

slowly anticlockwise until the alarm lamp comes on and the alarm sounds intermittently.

The display will alternate between showing “Cut” and the liquid temperature. This gives

an over-temperature trip point at the set temperature. The audible alarm can be

cancelled by pressing either the F or S button once.

The unit must be switched off to clear the cut-out alarm. To continue to use the TC120,

let the bath liquid cool by at least 5°C either naturally or by replacing the liquid. To avoid

nuisance tripping the trip point needs to be set at least 5°C above the desired control

temperature.

5.3.2 Setting a countdown timer

The TC120 includes a countdown timer in minutes which triggers an audible alarm on

completion. The timer can be set between 1 minute and 6000 minutes (100 hours).

1. Press the F button twice – the display will show “Cloc”.

2. Press the S button to select.

3. Use the main dial to select “On” and press the S button to select. The display flashes

with time (in minutes) indicated. Rotate navigator control to set time required.

4. Press the S button to save and return to liquid temperature display with timer

countdown started.

When the countdown clock is set the display alternates between bath temperature and

time remaining in minutes.

When the countdown timer reaches zero the audible alarm will sound and the display will

alternate between the water temperature and “End”. The alarm can be accepted by

pressing the either the F or S buttons.

Note: the TC120 will continue to control at the set temperature after the timer

reaches zero – the heater will not switch off.

30423 V4 T100 & TC120

Page 17 Operating Manual

www.grantinstruments.com

5.3.3 Cancelling the timer

The countdown timer can be easily cancelled.

1. Press the F button twice – the display will show “Cloc”.

2. Press the S button to select.

3. Use the main dial to select “Off” and press the S button to select. The display will

revert to the bath temperature and the timer will be cancelled.

5.3.4 Setting a high temperature warning alarm

The high temperature alarm sets a warning buzzer to sound if the bath temperature

exceeds a defined level.

1. Press the F button three times – the display will show ”Alar”.

2. Press the S button to select.

3. Use the main dial to select “On” and press the S button to select. The display flashes

the high temperature alarm value. Rotate the dial to set the high temperature alarm

required.

4. Press the S button to save and return to liquid temperature.

If the high temperature alarm value is exceeded then TC120 will sound the buzzer

intermittently and show “-Al-” on the display. The alarm can be acknowledged by

pressing either the F or S buttons. However, the alarm is persistent and will trigger again

if the temperature still exceeds the high temperature value. The alarm can be cancelled

by following the steps above but using the dial to select “Off” in step 3 and pressing the S

button to confirm.

Note: the high temperature alarm will not switch off the heater.

5.3.5 Selecting liquid type

The liquid type determines the limits of the set temperature range.

1. Press the F button four times – the display will show the current liquid type.

2. Use the main dial to select the required liquid.

3. Press the S button to set the liquid type and return to normal temperature display.

Selection of the liquid types below changes the settable range as follows:

Liquid

Set temperature range

H2O

0°C to 100°C

Oil

0°C to 120°C

LTL*

-25° to 50°C

* LTL = low temperature liquid, for example 50% water/50% glycol

T100 & TC120 30423 V4

Operating Manual Page 18

www.grantinstruments.com

EN

6.0 Technical specifications

6.1 Operating conditions

Ambient temperature range

5 to 40°C

Altitude above sea level

Up to 2,000m (6,500ft)

Operating environment

Indoor use only

Maximum relative humidity

80% RH up to 31°C decreasing to 50% RH at 40°C

6.2 Electrical details

Mains supply: 220-240V @ 50/60Hz or 110-120V @ 50/60Hz

Pollution degree: 2

Installation category: II

Mains supply voltage fluctuations are not to exceed ±10% of the nominal supply voltage.

6.3 Product performance

T100

T100L

TC120

TC120L

Settable temperature range

0°C to 100°C

-25°C to 120°C

Min operating temperature

5°C to 100°C

-25°C to 120°C

Stability (DIN 12876)

±0.05°C *

Uniformity (DIN 12876)

±0.1°C

Max pump head pressure

-

210mBar (no flow)

Max pump flow rate

-

16l/min

Max current consumption

6.5A

12.5A

6.5A

12.5A

Heater power

1.3kW

1.4kW

1.3kW

1.4kW

* Temperature stability may be affected (±0.3C) in the presence of strong RF fields (10V/m) at

380-400MHz. This level of interference is very unlikely and is only likely to be encountered in

electrically noisy industrial locations as defined in EN61326)

6.4 Bath accessories information

ST5

ST12

ST18

ST26

ST38

Tank capacity (litres)

5

12

18

26

38

Liquid depth min/max (mm)

85/140

75/130

125/180

P5

P12

P18

Tank capacity (litres)

5

12

18

Liquid depth min/max (mm)*

85/140

30423 V4 T100 & TC120

Page 19 Operating Manual

www.grantinstruments.com

7.0 Technical Tips

7.1 Which water should you use in your bath?

For the long-term reliability of water baths it is important to use oxygenated water that is

free from ions and minerals that can cause corrosion of stainless steel. We recommend

the use of distilled water and de-ionised water from modern ion exchange systems that

do not use salt back flushing to regenerate the ion-exchange cartridges.

Stainless steel is protected from corrosion by a layer of chromium oxide. If the layer is

damaged, oxygen present in water can reform the oxide layer. If the water is still or de-

oxygenated, and the oxide layer is damaged, ions can corrode the stainless steel tank. If

a water bath has been unused for some time, or water boiled, we recommend changing

to fresh distilled water or correct de-ionised water.

Water normally contains calcium or magnesium ions. De-ionised water has most ions

removed as indicated by its conductivity level; the purer the water the lower the

conductivity. It is important to use only de-ionised water from an ion exchange system

with replaceable cartridges. Do not use de-ionised water generated from an ion-

exchange system that incorporates a salt back-flush system to regenerate the ion-

exchange resin as this can leave sodium ions that are very corrosive to stainless steel.

7.2 How to prevent rust in water baths

Most Grant tanks, as well as immersed parts, are made from type 304 stainless steel, an

extremely versatile general purpose grade of stainless steel. It is the excellent forming

characteristic that has made this grade dominant in the manufacture of laboratory and

industrial water baths, as well as domestic sinks and saucepans. Type 304 stainless

steel is highly suitable for applications where hygiene is important; it exhibits good heat

resistance and excellent resistance to corrosion.

However, despite resistance to general surface corrosion, stainless steel is susceptible to

specific types of corrosion, in particular pitting (small pin hole style corrosion) and stress

corrosion cracking. It can also undergo general corrosion in specific environments, such

as one containing hydrochloric or sulphuric acids.

Stainless steel is protected by its high content of alloying elements, primarily chromium

and nickel. Chromium is the most important with respect to corrosion resistance,

although the nickel assists in allowing the chromium to do its job. The chromium forms an

oxide layer on the surface of the steel, which inhibits further oxidation. This layer adheres

extremely well to the metal substrate, but it is essential that it remains intact, and must be

protected from various forms of damage.

If the surface chromium oxide layer becomes damaged, oxygen present in water can

partially reform the oxide layer, so it is advisable to ensure that water is always fresh and

well oxygenated. Baths that will be out of use for an extended period should be emptied,

and all moisture should be wiped from the bottom of the tank.

In some cases a brown layer may appear on the surface of a stainless steel tank. In most

of these cases this is not rust, but it may be a surface deposit of minerals from the local

water supply, or ferrous particles or salts that have fallen into the tank. These surface

deposits can usually be removed by using a household cleaner such as Duraglit or Silvo

metal polish.

La pagina sta caricando ...

Grant Instruments Optima T100 Heated Circulating Bath Istruzioni per l'uso

Questo manuale è adatto anche per

Grant Instruments Optima T100 Heated Circulating Bath Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti