Moog QView QSDPT2-70NA5 Manuale utente

Marca: Moog

Modello: QView QSDPT2-70NA5

Categoria: Telecamere di sicurezza

Tipo: Manuale utente

Questo manuale è adatto anche per

www.moogvideolarm.com

Q S D

QView™ Series QSD 12" Outdoor Surveillance Dome

Installation and Operation Instructions for the following models:

QSDPT2-70NA5 Standard 12" outdoor, pendant mounted tinted dome with two (2) Day/Night

cameras, 7-50mm auto-iris lens

QSDPT4-70NA5 Standard 12" outdoor, pendant mounted tinted dome with four (4) Day/Night

cameras, 7-50mm auto-iris lens

Before attempting to connect or operate this product, please read these instructions completely.

To be used with the 81-IN5409 Instruction Manual.

81-IN5362

10-15-2012

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualied installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm

Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with

a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.

If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of

investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period

of the entire Product. The specic warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that

part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modication, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the

Product. Furthermore, Moog Videolarm shall have no liability where a schedule is specied for regular replacement or maintenance or cleaning of certain parts

(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-qualied personnel; operation of the Product outside of the

published environmental and electrical parameters, or if such Product’s original identication (trademark, serial number) markings have been defaced, altered,

or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not

been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”

(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any

cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR

ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL

CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT

THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS

PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL

PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER

FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,

REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):

Power 24Vac, Class 2 Only

26 watts at 24Vac Heater and Blower

Heater: 25 watts

Blower: 1 watt

Input Connectors (outdoor units):

Camera Power, BNC

(2) screw-down connectors

NOTE: This unit is designed for operation in an upright position.

Installing the QRH upside down may cause damage to the internal

equipment, and will void the warranty.

Be sure the bracket is properly and securely mounted to a

supporting structure capable of rigidly holding the weight of the

entire unit.

TO OPEN THE HOUSING

1. Open the housing by loosening the (3) security screws located on the housing ring

next to the lower clear dome (Figure 1).

Figure 1

INSTALLING THE HOUSING ASSEMBLY

PENDANT MOUNT

1. This unit includes a 1½" NPT coupling for a standard 1½" NPT pipe. The QSD

housing can be used with other brackets designed with 1½" male pipe threads, such

as the Moog Videolarm WM20G wall mount bracket.

2. Attach the housing coupling (Figure 2).

NOTE: Pipe threads should be clean and rust free. Use a sealer (such as Teon™

tape or silicone sealer) on the threads.

GENERAL INSTRUCTIONS:

Tools Required: .100" Flat Head Screwdriver

Phillips Head Screwdriver

Toolhead driver (supplied)

CAMERAS VOLTAGE CURRENT POWER

1 24Vac/Vdc 102mA 2.5W

2 24Vac/Vdc 210mA 5W

3 24Vac/Vdc 331mA 7.9W

4 24Vac/Vdc 487mA 10.9W

Use the formula below to select the correct power supply for cameras connected

in parallel (positive to positive, negative to negative):

Total current for a 24Vac system:

TOTAL CURRENT = (202mA x total number of cameras)

Note: 202mA is camera plus power supply

CABLE AND POWER GUIDELINES

This chart shows the proper current needed for power supplies for Q-View™

cameras. Use Class 2 Power only. Input voltage must be 24Vac/Vdc.

Figure 2

Add thread sealing

tape

Figure 3

Twist and

Secure

Wiring Color Code for Power

1 Camera Power (24Vac) Red

2 Camera Power (24Vac) Orange

3 Accessory Power (24Vac) Yellow

4 Accessory Power (24Vac) Green

POWER

1. Mount the housing assembly to the mounting bracket and housing coupling. A safety

cable is included with the housing to temporarily hold it while making wiring connections.

2. Clean the outside of the dome.

Use the formula below to select the correct

power supply for cameras connected in

parallel (positive to positive, negative to

negative):

Total current for a 24Vac system:

TOTAL CURRENT = (202mA x total

number of cameras) Example: 202mA x 5 total cameras = 1010mA

Note: 202mA is camera plus power supply

CAMERAS VOLTAGE CURRENT POWER

1 24Vac/Vdc 102mA 2.5W

2 24Vac/Vdc 210mA 5W

3 24Vac/Vdc 331mA 7.9W

4 24Vac/Vdc 487mA 10.9W

CABLE AND POWER GUIDELINES

This chart shows the proper current needed for power supplies for Q-View Series

cameras. Use Class 2 Power only. Input voltage must be

24Vac / Vdc.

CAMERAS TOTAL LOAD POWER SUPPLY 24 AWG 22 AWG 18 AWG 16 AWG

1 2.5W 24Vac/Vdc 1718/523 2733/833 6909/2106 10985/3348

2 5W 24Vac/Vdc 834/254 1327/404 3356/1023 5335/1626

3 7.9W 24Vac/Vdc 529/161 842/256 2129/649 3385/1032

4 10.9W 24Vac/Vdc 359/109 572/174 1447/441 2300/701

Power Supply Cable Maximum Length (feet/meters)

NOTE: The above table is based on a "worst-case" power supply. Using a regulated or switching power supply can increase your cable distance. Moog Videolarm recommends

using our PS24 power supply, or a CSA/UL listed Class 2 power supply.

Video Cable Maximum Length (feet/meters)

Cable Type RG-59 RG-6 RG-11

Wire Gauge 23 AWG* 18 AWG* 16 AWG*

Max. Length 750/229 1500/457 2000/610

* Copper clad steel core, 95% braided shield

AWG 250/76 500/152 1000/305 1500/457 2000/610 3000/914

18 3Ω 6Ω 13Ω 19Ω 26Ω 40Ω

20 5Ω 10Ω 20Ω 30Ω 40Ω 59Ω

22 8Ω 17Ω 33Ω 48Ω 66Ω 99Ω

24 13Ω 26Ω 52Ω 78Ω 108Ω 163Ω

Maximum Length (feet/meters)

The QRH is setup with (2) individual power inputs.

1. Accessory Power (yellow and green wire)

2. Camera Power (red and orange)

If you wish to provide a single power transformer it is recommended that:

1. Be certain that you know the total power consumption of the housing Heaters

(25 watts) + Blowers (2 watts) + camera/pan-tilt (not supplied)

2. Check the supplied wiring chart to be sure that you have the proper gauge wire for

the distance that you intend to run your power wires.

3. Bring power to the 3 and 4 position of the power connector

(yellow and green wire)

4. Two jumpers are provided in the housing packet. Jumper from the 1

position to

the 3

position and from the 2

position to the 4

position of the terminal block. Be

careful not to short between the yellow and green wires.

250

120

400

180

141

600

300

225

130

112

960

480

358

225

179

143

119

102

800

571

350

285

228

190

163

140

126

114

103

1300

905

525

452

362

301

258

215

201

181

164

150

139

129

120

113

106

100

1440

830

720

576

480

411

340

320

288

261

240

221

205

192

180

169

160

151

144

5.5

100

110

120

130

140

150

160

170

180

190

200

Maximum distance from transformer to load

Total vA

consumed

Wire Gauge

24V AC Wiring Distances

The following are the recommended maximum distances for 24 VAC

with a 10% voltage drop (10% is generally the maximum allowable

voltage drop for AC powered devices).

Figure 4

Add 2 jumpers for

single power input

CAMERA ADJUSTMENT

1. Access the cameras by removing the dome. Loosen the locking screws on the lip of

the dome. DO NOT TAKE THESE SCREWS OUT. Once the screws are loosened, turn

the dome counter clockwise until it stops, then pull the dome off.

CAMERA FOCUSING (FOR EACH CAMERA)

Fixed Lens: Loosen the set screw in the lens mount. Manually rotate the lens until a

clear picture is achieved. Once the focus is set, retighten the set screw (Figure 5).

Figure 5

Set screw

Fixed lens

Auto Iris Lens:

NOTE: THE AUTO IRIS LENS IS SET AT THE FACTORY.

• IF YOU EXPERIENCE VIDEO TOO LIGHT OR DARK AUTO IRIS ADJUSTMENT

MAY BE NEEDED.

SEE THE TROUBLESHOOTING SECTION FOR

ADJUSTMENT INFORMATION.

CAMERA SETTINGS

HIGH-RES BLACK & WHITE

FIXED AND FIXED VARI-FOCAL LENSES. There are no user adjustable settings on

these units (Figure 6).

Figure 6

AUTO IRIS LENSES. The dip switches are factory set with AES off and backlight

compensation on (Figure 7). The auto iris is also set at the factory, but an adjustment

screw is included for use if needed. See page 10 for instructions on adjusting Auto Iris.

Auto Iris

adjustment

screw

AES Default Off

Backlight

Compensation

Default On

Figure 7

BW Fixed and Vari-Focal

BW Auto Iris

NOTE: To determine which camera is used in your unit, locate the serial number on the

inside of the housing. Match the two letter prex with the corresponding instructions

included here for adjustments.

NOTE: This hi-res color camera uses a 1/4" chip and a 3-6mm auto iris lens. It is

comparable to a 1/3" chip using a 4-9mm auto iris lens.

The operational settings are dened by four dip switches located on the side of the PC

Board (Figure 9 and 10). Moving the switches to the UP position will activate specic

settings. Refer to the chart below.

Figure 9

Auto Iris

Adjustment

Screw

Dip Switches

Figure 10

Dip Switch UP DOWN

(Iris) Auto Iris On Position for Fixed Lens

(Flickerless) Shutter speed Normal

xed at 1/100 sec.

3 (Back Light ON Normal

Compensation

(Synch Mode) Internal Synch Line Lock Mode

HIGH-RES COLOR & DAY/NIGHT w/AUTO-IRIS

HIGH-RES COLOR, FIXED LENS

FIXED AND FIXED VARI-FOCAL LENSES. There are no user adjustable settings on

these units (Figure 8)

AUTO IRIS LENSES: The auto iris can be adjusted if needed. See the Troubleshooting

section for instructions.

Figure 8

Auto Iris

adjustment

screw

COMPLETION OF INSTALLATION

1. When the desired focus is achieved for each camera, adjust the segmented bracket

arms to the desired viewing angle. Once you've nished, put the dome back in place

and check to be sure none of the cameras touch the dome. If one or more do, readjust

the arm(s) until they are clear of the dome.

2. Reattach the dome by putting it in place, turning clockwise until it locks, and then

tightening the locking screws.

NVT INSTRUCTIONS

The cameras included in the Q-View™ series have the option of transmitting video

signals to NVT receivers via unshielded twisted pair cable. You must purchase the

receiver separately. Instructions for connecting the receiver end of the unshielded

twisted pair cable will be included with the NVT receiver. Following are instructions

for connecting the unshielded twisted pair cables to the RJ45 (Cat. 5) cable running

outside your housing.

UNSHIELDED TWISTED PAIR

VIDEO WIRING

1. Video for all four cameras is contained in the one RJ45 (Cat. 5) cable. An RJ45

female coupling is provided so that all connections can be made with an RJ45

connector. The following is the wiring diagram for the four twisted pair wires that are

included with the Cat. 5 cable.

2. Connect the other end of the unshielded twisted pair cable to the NVT receiver.

CAUTION: The unshielded twisted pair video signal is polarity dependent. The positive

video wire for each camera MUST be connected to the positive terminal on the NVT

receiver, and negative MUST be connected to negative.

3. When using unshielded twisted pair cable you DO NOT need the BNC connector. All

four BNC connectors are provided inside the housing for testing purposes. Be sure that

there is no video connection other than the unshielded twisted pair cable.

NOTE: The customer must purchase the Video Transceiver from

NVT. Part numbers are:

• NV-212A (500 ft.)

* NV-213A or NV-213A-M (1000 ft.)

• NV-652R, NV-862R, or NV-1662R (3000 ft.)

PIN WIRE COLOR CAMERA NUMBER

1 White/Green Camera 1 +

2 Green Camera 1 -

3 White/Orange Camera 2 +

6 Orange Camera 2 -

5 White/Blue Camera 3 +

4 Blue Camera 3 -

7 White/Brown Camera 4 +

8 Brown Camera 4 -

Wiring Notes

Wire — What to DO

1. DO use point-to-point Unshielded Twisted Pair wire, gauge 24 or thicker, stranded

or solid, Category 2, 3, 4, or 5.

2. The video signal may co-exist in the same wire bundle as other video, telephone,

data, control signals, or low-voltage power. It is also OK to run NVT video signals in

or near electromagnetic fields (in accordance with National Electrical Code, local,

or other local safety requirements).

3. DO measure the wire distance. Use only transceivers that are designed for that

distance.

4. DO make sure the pair of wires carrying the video signal is sent as a twisted pair

(e.g. the blue-white/white-blue wires twisted together as a pair), not a “split-

pair” (e.g. blue-white conductor, part of one pair/orange-white conductor, part

of another pair).

Wire — What NOT to DO

1. DO NOT USE SHIELDED TWISTED PAIR WIRE. It will severely degrade the

distance performance. Short runs may be used with some signal degradation (for

example elevator traveler cables). Multi-pair wire with an overall shield is OK.

2. DO NOT USE UN-TWISTED WIRE. It will reduce the NVT product’s inherent

interference immunity.

3. DO NOT allow your installation to have “bridge-taps”, loading coils, talk-battery,

or MOV type protectors. Bridge-taps are where a twisted pair is connected to two

twisted pairs (such as an extension phone at home). Bridge-taps cause reflections

as the signal propagates, resulting in “ghosts” in the video image, and are to be

avoided.

4. If the phone company is providing the cable runs between buildings, make sure

it’s “dry copper” i.e. it should have none of the following: dial-tone, 48 volts, loading

coils, bridge-taps, switching, or long paths to the phone company’s central office and

back.

5. Due to near-end crosstalk, DO NOT send a transmit and a receive signal in the

same wire bundle. Exceptions: Less than 1,000 ft (300m), or Category 5 cable, up to

2,000 ft (600m) are OK.

6. DO NOT send “Up-the-Coax” Pan/Tilt/Zoom signals through active (amplified)

NVT transceivers.

Measure your wire distance

Note: All NVT quoted distance specifications include any coax in the run. It is

recommended that the wire distance be measured to ensure that the capability of the

NVT product is correct.

Wire resistance may be measured with an ohm-meter by shorting the two conductors

together at the far end, and measuring the loop-resistance out and back. Compare

your readings with the charts in the next column.

7. For safety, never put NVT signals in the same conduit as high-voltage

wiring.

8. WARNING — to reduce a risk of fire or electrical shock, do not expose

this product to rain or moisture.

AC Voltmeter

Camera

Monitor

Bridge Tap

NV-213

NVT TROUBLESHOOTING

If you are experiencing problems, attempt to simplify your setup. Test each cable

segment separately. For example, test the camera and monitor together without the

other equipment. Then add in the NVT transceivers, back-to-back. Test each segment

of a long cable-run independently. Attempt to isolate the problem.

Below are problems that may be encountered. If the suggestions below are not helpful,

or the recommendations are not effective, please call NVT’s customer support. NVT

customer support can be reached 8:00 AM to 5:30 PM PST at (800) 959-9870 or at

(+1) (650) 562-0600.

FAINT OR BLURRY PICTURE; LITTLE OR NO COLOR

Possible causes include:

1. Shielded twisted-pair cable. Verify that the wire is unshielded twisted-pair cable.

Multi-pair cable with an overall shield is OK.

2. Longer wire distance than expected. Be sure to include any coax cable that’s part of

this distance. Verify end-to-end connectivity with an ohm meter. Measure the distance

by disconnecting the transceivers, shorting the far end, reading the loop’s resistance

at the near end. See above for ohm vs. distance ratings. If necessary, replace

transceivers with correct models specified for this distance.

3. Incorrect distance equalization setting. Adjust the equalization controls) with a mini

screwdriver (NV-652R, NV-862R or the NV-1662R). If the transmitter is an NV-653T,

verify correct equalization switch setting.

4. Poor connection at a punch-block, splice, or coax cable. Re-check using the

method described in #2 above, or use a wire test set.

5. Short between conductors of the twisted-pair. Use an ohm meter to locate the short.

6. Transient protection devices employing metal-oxide varistors. Use carbon blocks,

gas-discharge tubes, or NVT transceivers w

ith built-in protection.

7. Check the camera. Are the focus and iris set correctly? Verify with portable monitor.

EXTREMELY FAINT PICTURE

Only faint shadows of the original picture are visible. One of the twisted pair conductors

is open or the wires are shorted together. Check with an ohm meter.

OVER-SATURATED COLORS; HIGH CONTRAST GRAINY PICTURE; TOO BRIGHT,

TORN PICTURE

Adjust the distance equalization as necessary. Verify that the monitor has a 75

termination, not in “loop-through”.

WON'T SYNC; WIDE, WHITE JAGGED AREAS

Looks like a scrambled Cable TV signal. Check polarity.

WON'T SYNC; TORN PICTURE

1. Make sure that you are using unshielded twisted pair wire.

2. Check distance equalization settings.

3. For installations with passive (non-amplified) transceivers at both ends, check for

ground loops. This may be done with an AC Voltmeter, as shown below:

If the voltage is greater than 1/2 volt, use an amplified receiver, such as the NV-652R,

NV-862R, or NV-1662R.

Alternately, remove the ground at one end (usually at the camera end). Be sure that

floating the camera conforms to local/regional and National Electrical Codes.

4. Check for crosstalk from a second video path. Disconnect all other video sources.

If the problem goes away, check for a split-pair or un-twisted wire.

FAINT STRIPES GLIDING UP OR DOWN THE SCREEN

These are caused by crosstalk from a second video path, or with ground-loops in

installations employing passive models at both ends.

1. To identify, disconnect all other video signals temporarily. If the interference goes

away, check the wire to make sure the signal is traveling through a twisted pair. Is

two-way video being sent more than 1,000 ft (300m) over Category 2 or 3 wire? If so,

the send and receive signals may need to go in separate jacketed cables, or upgrade

to Category 5 wire.

2. Next, check for ground loops. See #3 above.

NO POWER LIGHT ON THE NVT UNIT

Check the blue “power” LED on powered NVT units. If the light is not on, the receiver

is not getting power. Re-check the power source and connections.

If the green LED is on but the power LED is off, check that the power supply is floating.

Grounding one side of the power input may cause this condition.

NO GREEN LIGHT, NO VIDEO

The NV-652R, NV-862R or NV-1662R series receiver/hub is not detecting a video

signal. There is an open or shorted connection. Use a multimeter to locate the fault.

GHOSTS

Faint shadows of the original signal shifted to the right. This is caused by an

impedance mismatch along the wire. Verify that the monitor is terminated with 75 (not

in “loop-through”.) Check that all wire is unshielded twisted pair. The high-frequency

wire impedance should be 100. Check for bridge-taps (see below) either by inspecting

wiring closet connections, or, if available, using a “Time-Domain Reflectometer”

(T.D.R.), sometimes called a “cable tester”.

If the faint shadows are not copies of the original picture, but from the picture of some

other camera, check for crosstalk:

Is any portion of the wire un-twisted?

Are the signals from two cameras split between two pairs?

Is there a short between a conductor of one signal and a conductor of another?

Power Supply

Power A

Power B

Camera

Assembly

Primary

Power

Video Signal

Video Shield

Monitor

(Ground Return)

Figure A Ground Loop

TROUBLESHOOTING

If you experience problems with the camera picture please check these simple

troubleshooting procedures for possible solutions before calling technical support.

IMPORTANT NOTE: If you have removed the ground loop and the horizontal line still

remains on screen call Moog Videolarm technical support for further information.

GROUND LOOPS

Generally a horizontal line on screen, whether moving or stationary, means you have

a ground loop problem. The video shield should only be connected to ground through

the monitor or other electronic equipment that uses the video signal. Connecting the

video shield to ground at the camera will create a ground loop, which may interfere

with the video signal (See Figure A). This should not damage the camera, but the

video signal may become unusable. A ground loop problem will cause a dark horizontal

bar to slowly “scroll" through the picture. To solve this problem, remove all ground

connections from the video connection EXCEPT for the ground at the terminating

end of the video signal.

The video termination should be a 75-ohm impedance, standard in monitors

and other video equipment. If the video signal goes to more than one piece of

equipment, a monitor and multiplexer input for instance, insure that one and only

one piece of equipment terminates the video signal with 75 ohms; otherwise the

image will be degraded and may appear to be unusually dim.

STATIONARY OR SCROLLING HORIZONTAL

LINES ON SCREEN

PICTURE IS CLEAR, LOW OR NO COLOR;

PICTURE IS DARK OR GRAINY IN GOOD

LIGHTING CONDITIONS

The auto iris lens is set at the factory. If you experience video too light or dark you can

manually adjust using the auto iris adjustment screw.

If there is low or no color the Auto Iris is too open, if the picture is dark or grainy in

good conditions the Auto Iris is too closed.

To adjust the auto iris lens, rst locate the AUTO IRIS ADJUSTMENT SCREW on the

camera PC board. Using a small insulated screwdriver (blade width of from 1/16" to

3/32"), adjust the control.

Turning the control CLOCKWISE opens the iris, making the image brighter.

Turning the control COUNTER CLOCKWISE closes the iris, making the image darker.

Figure D

AUTOMATIC BROWN OUT FEATURE

The camera includes an automatic brown out feature which is activated whenever the

incoming voltage drops below 10 Vac or Vdc.

IMPORTANT NOTE ON AUTO IRIS ADJUSTMENT:

WHEN ADJUSTING, USE A SMALL, INSULATED SCREWDRIVER. The auto iris

adjustments are very sensitive. Use gentle pressure when turning. To adjust, turn

either clock-wise or counter-clockwise no more than one degree at a time. Check

the monitor after each turn to determine is the desired brightness and color have

been obtained. When the adjustment is satisfactory, place a hand over the lens to

block out all light. Quickly remove the hand to be sure the iris reacts.

LINE LOCK

All cameras are all shipped from the factory with the line lock function disabled. If your

application requires Line Lock contact Videolarm.

Auto Iris

Adjustment

Screw

COLOR & DAY/NIGHT AUTO-IRIS

Figure B

BLACK & WHITE AUTO-IRIS

Auto Iris

Adjustment

Screw

Product Registration/Warranty

Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest

quality products available and superior customer service.

Should a problem arise, rest assured that Moog Videolarm stands behind its products by offering impressive 3 Year and 5 Year warranties, depending on the product

purchased. See full warranty details at www.moogvideolarm.com/technical-support/warranty-plan/

Please take a few moments to register your purchase via the Online Product Registration Form at:

www.moogvideolarm.com/technical-support/product-registration

• Simple and Trouble-Free RMA process

• Receive product updates, and special promotion

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…