PowerWalker VFI 6000R LCD Manuale del proprietario

EN

Online UPS

PowerWalker VFI 6000R LCD (Rack)

PowerWalker VFI 10000R LCD

(Rack)

Manual

EN/ES/IT/TR/PT

1

EN

Please comply with all warnings and operating instructions

in this manual strictly. Save this manual properly and read

carefully the following instructions before installing the

unit. Do not operate this unit before reading through all

safety information and operating instructions carefully.

2

EN

Table of Contents

1. IMPORTANT SAFETY INSTRUCTION ............................................................................................. 3

2. INSTALLATION AND OPERATION.................................................................................................. 5

2-1. UNPACKING AND INSPECTION .............................................................................................................................................. 5

2-2. REAR PANEL VIEW ............................................................................................................................................................. 5

2-3. SINGLE UPS INSTALLATION.................................................................................................................................................. 7

2-4. UPS INSTALLATION FOR PARALLEL SYSTEM ............................................................................................................................. 9

2-5. SOFTWARE INSTALLATION.................................................................................................................................................. 10

3. OPERATIONS ............................................................................................................................ 11

3-1. BUTTON OPERATION ........................................................................................................................................................ 11

3-2. LED INDICATORS AND LCD PANEL ...................................................................................................................................... 11

3-3. AUDIBLE ALARM ............................................................................................................................................................. 13

3-4. SINGLE UPS OPERATION .................................................................................................................................................. 14

3-5. PARALLEL OPERATION ...................................................................................................................................................... 16

3-6. ABBREVIATION MEANING IN LCD DISPLAY ........................................................................................................................... 18

3-7. LCD SETTING ................................................................................................................................................................. 18

3-8. OPERATING MODE/STATUS DESCRIPTION ............................................................................................................................ 23

3-10. WARNING INDICATOR .................................................................................................................................................... 25

4. TROUBLE SHOOTING................................................................................................................. 26

5. STORAGE AND MAINTENANCE .................................................................................................. 28

5-1. STORAGE ....................................................................................................................................................................... 28

5-2. MAINTENANCE ............................................................................................................................................................... 28

6. SPECIFICATIONS ........................................................................................................................ 29

3

EN

1. IMPORTANT SAFETY INSTRUCTION

SAVE THESE INSTRUCTIONS – This manual contains important instructions for models PowerWalker VFI

6000/1000 LCD that should be followed during installation and maintenance of the UPS and batteries.

 This product is specially designed for PCs and it is not recommended for use in any life-supporting system

and other specific important equipment.

 This equipment can be operated by any individual with no previous training.

 Do not plug household appliances such as hair dryers to UPS receptacles.

 This unit intended for installation in a controlled environment (temperature controlled, indoor area free of

conductive contaminants). Avoid installing the UPS in locations where there is standing or running water, or

excessive humidity.

 Risk of electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified

service personnel.

 The utility power outlet shall be near the equipment and easily accessible. To isolate UPS from AC input,

remove the plug from the utility power outlet.

 If UPS is to be stored for a long time, it is recommended to recharge the batteries (by connecting the utility

power to UPS, switch “ON”), once a month for 24 hours to avoid a full battery discharge.

 Please do not use the UPS in excess of the rated load capacity.

 The UPS contains one/two large-capacity batteries. So the shell shall not be opened, otherwise such

dangers as electric shock will be caused. If any internal overhaul or replacement of the battery is required,

please contact the distributor.

 The internal short circuiting of the UPS will lead to dangers such as electric shock or fire, therefore, no

water containers (such as a water glass) shall be placed on the top of the UPS so as to avoid such dangers as

electric shock.

 Do not dispose of battery or batteries in a fire. The battery may explode.

 Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes. It

may be toxic.

 Icon Φ on the rating label stands for phase symbol.

 A battery can present a risk of electrical shock and high short circuit current. The following precautions

should be observed when working on batteries :

 Remove watches, rings, or other metal objects from the hand.

 Use tools with insulated handles.

 Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the

required precautions. Keep unauthorized personnel away from batteries.

 When replacing batteries, replace with the same type and number of the sealed lead-acid batteries.

 The maximum ambient temperature rating is 40°C.

 This pluggable type A equipment with battery already installed by the supplier is operator installable and

may be operated by laymen.

 During the installation of this equipment it should be assured that the sum of the leakage currents of the

UPS and the connected loads does not exceed 3.5mA.

 Attention, hazardous through electric shock. Also with disconnection of this unit from the mains, hazardous

voltage still may be accessible through supply from battery. The battery supply should be therefore

disconnected in the plus and minus pole of the battery when maintenance or service work inside the UPS is

necessary.

 The mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily accessible.

 In case smoke is found coming out from the device, please cut off the power supply quickly and contact the

distributor.

4

EN

 Do not keep or use this product in any of the following environments:

o Any area with combustible gas, corrosive substance or heavy dust.

o Any area with extraordinarily high or low temperature (above 40˚C or below 0˚C) and humidity of

more than 90%.

o Any area exposed to direct sunshine or near any heating apparatus.

o Any area with serious vibrations.

o Outdoor.

 In the event that there is fire occurring in the vicinity, please use dry-power extinguishers. The use of liquid

extinguishers may give rise to the danger of electric shock.

This product complies with the safety and environmental regulations in EU.

If the time arises to throw away your product, please recycle all the components possible. Batteries and

rechargeable batteries are not to be disposed in your domestic waste! Please recycle them at your local recycling

point. Together we can help to protect the environment.

5

EN

2. Installation and Operation

There are two different types of online UPS: standard and long-run models. Please refer to the following model

table.

Model

Type

Model

Type

6000

Standard

model

6000L

Long-run

model

10000

10000L

6000R

6000RL

10000R

10000RL

We also offer optional parallel function for these two types by request. The UPS with parallel function is called as

“Parallel model”. We have described detailed installation and operation of Parallel Model in the following chapter.

2-1. Unpacking and Inspection

Unpack the package and check the package contents. The shipping package contains:

● One UPS

● One user manual

● One monitoring software CD

● One RS-232 cable (option)

● One USB cable

● One EPO plug

● One parallel cable (only available for parallel model)

● One share current cable (only available for parallel model)

● One battery cable (only available for long-run model)

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged during

transportation. Do not turn on the unit and notify the carrier and dealer immediately if there is any damage or

lacking of some parts. Please keep the original package in a safe place for future use.

2-2. Rear Panel View

Diagram 1: Rear Panel Overlook 6000(L)/10000(L)

6

EN

Diagram 2: Input/Output Terminal

Diagram 3: Rear Panel Overlook 6000R(L)/10000R(L) Diagram 4: Input/Output Terminal

Diagram 5: 6KR/10KR battery pack rear panel

1. RS-232 communication port

2. USB communication port

3. Emergency power off function connector (EPO connector)

4. Share current port (only available for parallel model)

5. Parallel port (only available for parallel model)

6. Intelligent slot

7. Cooling fan

8. External maintenance bypass switch port

9. Maintenance bypass switch

10. Input circuit breaker

11. Output receptacles: connect to mission-critical loads

12. Output circuit breaker for receptacles

13. Input/Output terminal (Refer to Diagram 2 & 4 for the details)

14. Output terminal: connect to mission-critical loads

15. Programmable output terminal: connect to non-critical loads

16. External battery connector (only available for Long-run model)

17. Utility input terminal

18. Grounding terminal

19. Battery pack output circuit breaker

7

EN

2-3. Single UPS Installation

Installation and wiring must be performed in accordance with the local electric laws/regulations and execute the

following instructions by professional personnel.

1) Make sure the mains wire and breakers in the building are enough for the rated capacity of UPS to avoid the

hazards of electric shock or fire.

NOTE: Do not use the wall receptacle as the input power source for the UPS, as its rated current is less than the

UPS’s maximum input current. Otherwise the receptacle may be burned and destroyed.

2) Switch off the mains switch in the building before installation.

3) Turn off all the connected devices before connecting to the UPS and then switch off the internal output

breaker.

4) Prepare wires based on the following table:

Model

Wiring spec (AWG)

Input

Output

Battery

Ground

6000

10

6000L

10

10000

8

10000L

8

6000R

10

6000RL

10

10000R

8

10000RL

8

NOTE 1: The cable for 6000/6000L should be able to withstand over 40A current. It is recommended to use

10AWG or thicker wire for safety and efficiency.

NOTE 2: The cable for 10000/10000L should be able to withstand over 63A current. It is recommended to use

8AWG or thicker wire for safety and efficiency.

NOTE 3: The selections for color of wires should be followed by the local electrical laws and regulations.

5) Remove the terminal block cover on the rear panel of UPS. Then connect the wires according to the following

terminal block diagrams: (Connect the earth wire first when making wire connection. Disconnect the earth wire last

when making wire disconnection!)

Terminal Block wiring diagram of 6000(L)/10000(L)

Input Neutral

Input Line

Output 2 Neutral

Output 2 Line

Output 1 Neutral

Output 1 Line

8

EN

Terminal Block wiring diagram for 6000R(L)/10000R(L)

NOTE 1: Make sure that the wires are connected tightly with the terminals.

NOTE 2: There are two kinds of outputs: output terminal/outlets and programmable terminal. Please connect

non-critical devices to the programmable terminal and critical devices to the output terminal/outlets. During power

failure, you may extend the backup time to critical devices by setting shorter backup time for non-critical devices.

NOTE 3: The internal output breaker is used to cut off the output, but we suggest you to install an external output

breaker between the output terminal and the load. This breaker should be installed in an easy access area which

will allow you to cut off the output immediately in an emergency. And the breaker should be equipped with leakage

current protection if necessary.

6) Insert the EPO plug into the EPO slot on the rear panel.

7) Put the terminal block cover back to the rear panel of the UPS.

Warning: (Only for standard model)

● Make sure the UPS is not turned on before installation. The UPS should not be turned on during wiring

connection.

● Do not try to modify the standard model to the long-run model. Particularly, do not try to connect the standard

internal battery to the external battery. The battery type and voltage may be different. If you connect them

together, it maybe causes the hazard of electric shock or fire!

Warning: (Only for long-run model)

● Make sure a DC breaker or other protection device between UPS and external battery pack is installed. If not,

please install it carefully. Switch off the battery breaker before installation.

NOTE: Set the battery pack breaker in “OFF” position and then install the battery pack.

● Give highly attention to the rated battery voltage marked on the rear panel. If you want to change the numbers

of the battery pack, please make sure you modify the setting simultaneously. The connection with wrong

battery voltage may cause permanent damage of the UPS. Make sure the voltage of the battery pack is correct.

● Give highly attention to the polarity marking on external battery terminal block, and make sure the correct

battery polarity is connected. Wrong connection may cause permanent damage of the UPS.

● Make sure the protective earth ground wiring is correct. The wire current spec, color, position, connection and

conductance reliability should be checked carefully.

● Make sure the utility input & output wiring is correct. The wire current spec, color, position, connection and

conductance reliability should be checked carefully. Make sure the L/N site is correct, not reverse and

short-circuited.

Input Neutral

Input Line

Ground

Output Line

Output Neutral

9

EN

2-4. UPS Installation for Parallel System

If the UPS is only available for single operation, you may skip this section to the next.

1) Install and wires the UPSs according to the section 2-3.

2) Connect the output wires of each UPS to an external output breaker.

3) Connect all external output breakers to a major output breaker. Then this major output breaker will directly

connect to the loads.

4) Each UPS is connected to an independent battery pack.

NOTE: The parallel system can not use one battery pack. Otherwise, it will cause system permanent failure.

5) Remove the cover of parallel share current cable port on the UPS, connect each UPS one by one with the

parallel cable and share current cable, and then screw the cover back again.

6) Refer to the following wiring diagram:

Diagram 1: Power cable connection

Wiring diagram of parallel system 6000(L)/10000(L)

Parallel communication port connection

Share current cable connection

10

EN

Diagram 2: Power cable connection

Wiring diagram of parallel system for 6000R(L)/10000R(L)

2-5. Software Installation

For optimal computer system protection, install UPS monitoring software to fully configure UPS shutdown. You may

insert provided CD into CD-ROM to install the monitoring software. If not, please follow steps below to download

and install monitoring software from the internet:

1. Go to the website http://www.powerwalker.com/software.html

2. Click ViewPower software icon and then choose your required OS to download the software.

3. Follow the on-screen instructions to install the software.

4. When your computer restarts, the monitoring software will appear as an orange plug icon located in the system

tray, near the clock.

Diagram 4

Parallel communication port

connection

Share current cable connection

Check www.powerwalker.com/viewpower.html for latest software version.

11

EN

3. Operations

3-1. Button Operation

Button

Function

ON/Enter Button

 Turn on the UPS: Press and hold the button more than 0.5s to turn on the UPS.

 Enter Key: Press this button to confirm the selection in setting menu.

OFF/ESC Button

 Turn off the UPS: Press and hold the button more than 0.5s to turn off the UPS.

 Esc key: Press this button to return to last menu in setting menu.

Test/Up Button

 Battery test: Press and hold the button more than 0.5s to test the battery while in AC

mode, or CVCF mode.

 UP key: Press this button to display next selection in setting menu.

Mute/Down Button

 Mute the alarm: Press and hold the button more than 0.5s to mute the buzzer.

Please refer to section 3-4-9 for details.

 Down key: Press this button to display previous selection in setting menu.

Test/Up +

Mute/Down Button

 Press and hold the two buttons simultaneous more than 1s to enter/escape the

setting menu.

* CVCF mode means converter mode.

3-2. LED Indicators and LCD Panel

LED Indicators:

There are 4 LEDs on front panel to show the UPS working status:

Mode LED

Bypass

Line

Battery

Fault

UPS Startup

●

Bypass mode

●

○

AC mode

○

●

○

Battery mode

○

●

○

CVCF mode

○

●

○

Battery Test

●

○

ECO mode

●

○

Fault

○

●

Note: ● means LED is lighting, and ○ means LED is faded.

LCD panel

LED indicators

12

EN

LCD Panel:

Display

Function

Backup time information

Indicates battery discharge time in numbers.

H: hours, M: minutes, S: seconds

Fault information

Indicates that the warning and fault occurs.

Indicates the fault codes, and the codes are listed in details in section 3-9.

Mute operation

Indicates that the UPS alarm is disabled.

Output & Battery voltage information

Indicates the output voltage, frequency or battery voltage.

Vac: output voltage, Vdc: battery voltage, Hz: frequency

Load information

Indicates the load level by 0-25%, 26-50%, 51-75%, and 76-100%.

Indicates overload.

Indicates the load or the output is short.

Programmable output information

Indicates that the programmable outputs are working.

Mode operation information

Indicates the UPS connects to the mains.

Indicates the battery is working.

Indicates the bypass circuit is working.

13

EN

Indicates the ECO mode is enabled.

Indicates the Inversor circuit is working.

Indicates the output is working.

Battery information

Indicates the Battery capacity by 0-25%, 26-50%, 51-75%, and 76-100%.

Indicates the battery is not connected.

Indicates low battery level and low battery voltage.

Input & Battery voltage information

Indicates the input voltage or frequency or battery voltage.

Vac: Input voltage, Vdc: battery voltage, Hz: input frequency

3-3. Audible Alarm

Description

Buzzer status

Muted

UPS status

Bypass mode

Beeping once every 2 minutes

Yes

Battery mode

Beeping once every 4 seconds

Fault mode

Beeping continuously

Warning

Overload

Beeping twice every second

No

Low battery

Beeping once every second

Battery unconnected

Over charge

EPO enable

Fan failure/Over temperature

Charger failure

IP fuse broken

Overload 3 times in 30min

EPO status

Cover of maintain switch is open

Fault

Bus start failure

Beeping continuously

Yes

Bus over

Bus under

Bus unbalance

Bus short circuited

Inversor soft start failure

High Inversor voltage

Low Inversor voltage

Inversor output short circuited

Negative power fault

Battery SCR short circuited

Inversor relay short circuited

Battery voltage loss

Parallel communication failure

Parallel output current unbalance

Over temperature

CPU communication failure

Overload

14

EN

3-4. Single UPS Operation

1. Turn on the UPS with utility power supply (in AC mode)

1) After power supply is connected correctly, set the breaker of the battery pack at “ON” position (the step

only available for long-run model). When setting input breaker at “ON” position, the fan will start running.

Then, set the internal output breaker at “ON” position. The UPS will supply power to the loads via the

bypass. Now, the UPS is operating in Bypass mode.

NOTE 1: When UPS is in Bypass mode, the output voltage will directly power from utility after you switch on

the input breaker and internal output breaker. In Bypass mode, the load is not protected by UPS. To protect

your precious devices, you should turn on the UPS. Refer to next step.

2) Press and hold the “ON” button for 0.5s to turn on the UPS and the buzzer will beep once.

3) A few seconds later, the UPS will enter to AC mode. If the utility power is abnormal, the UPS will operate

in Battery mode without interruption.

NOTE: When the UPS is running out battery, it will shut down automatically at Battery mode. When the

utility power is restored, the UPS will auto restart

2. Turn on the UPS without utility power supply (in Battery mode)

1) Make sure that the breaker of the battery pack is at “ON” position (only for long-run model).

2) Press and hold the “ON” button for 0.5s to turn on the UPS, and the buzzer will beep once.

3) A few seconds later, the UPS will be turned on and enter to Battery mode.

3. Connect devices to UPS

After the UPS is turned on, you can connect devices to the UPS.

1) Turn on the UPS first and then switch on the devices one by one, the LCD panel will display total load level.

2) If it is necessary to connect the inductive loads such as a printer, the in-rush current should be calculated

carefully to see if it meets the capacity of the UPS, because the power consumption of this kind of loads is

too big.

3) If the UPS is overload, the buzzer will beep twice every second.

4) When the UPS is overload, please remove some loads immediately. It is recommended to have the total

loads connected to the UPS less than 80% of its nominal power capacity to prevent overload for system

safety.

5) If the overload time is over acceptable time listed in spec at AC mode, the UPS will automatically transfer

to Bypass mode. After the overload is removed, it will return to AC mode. If the overload time is over

acceptable time listed in spec at Battery mode, the UPS will become fault status. At this time, if bypass is

enabled, the UPS will power to the load via bypass. If bypass function is disabled or the input power is not

within bypass acceptable range, it will cut off output directly.

4. Charge the batteries

1) After the UPS is connected to the utility power, the charger will charge the batteries automatically except

in Battery mode or during battery self-test.

2) Suggest charging batteries at least 10 hours before use. Otherwise, the backup time may be shorter than

expected time.

3) make sure the battery numbers setting on the control board (Please refer to the section 3-4-12 for detailed

setting) is consistent to real connection.

15

EN

5. Battery mode operation

1) When the UPS is in Battery mode, the buzzer will beep according to different battery capacity. If the

battery capacity is more than 25%, the buzzer will beep once every 4 seconds; If the battery voltage drops

to the alarm level, the buzzer will beep quickly (once every sec) to remind users that the battery is at low

level and the UPS will shut down automatically soon. Users could switch off some non-critical loads to

disable the shutdown alarm and prolong the backup time (the UPS would cut off the programmable

output terminal automatically when the programmable timer function is enabled). If there is no more load

to be switched off at that time, you have to shut down all loads as soon as possible to protect the devices

or save data. Otherwise, there is a risk of data loss or load failure.

2) In Battery mode, if buzzer sound annoys, users can press the Mute button to disable the buzzer.

3) The backup time of the long-run model depends on the external battery capacity.

4) The backup time may vary from different environment temperature and load type.

5) When setting backup time for 16.5 hours (default value from LCD panel), after discharging 16.5 hours, UPS

will shut down automatically to protect the battery. This battery discharge protection can be enabled or

disabled through LCD panel control. (Refer to 3-7 LCD setting section)

6. Test the batteries

1) If you need to check the battery status when the UPS is running in AC mode/CVCF mode/ECO mode, you

could press the “Test” button to let the UPS do battery self-test.

2) To keep the system reliable, the UPS will perform the battery self-test automatically periodically. The

default setting period is once per week.

3) Users also can set battery self-test through monitoring software.

4) If the UPS is at battery self-test, the LCD display and buzzer indication will be the same as at Battery mode

except that the battery LED is flashing.

7. Turn off the UPS with utility power supply in AC mode

1) Turn off the Inversor of the UPS by pressing “OFF” button for at least 0.5s, and then the buzzer will beep

once. The UPS will turn into Bypass mode.

NOTE 1: If the UPS has been set to enable the bypass output, it will bypass voltage from utility power to

output sockets and terminal even though you have turned off the UPS (Inversor).

NOTE 2: After turning off the UPS, please be aware that the UPS is working at Bypass mode and there is risk

of power loss for connected devices.

2) In Bypass mode, output voltage of the UPS is still present. In order to cut off the output, switch off the

internal output breaker and input breaker. A few seconds later, there is no display shown on the display

panel and UPS is complete off.

8. Turn off the UPS without utility power supply in Battery mode

1) Turn off the UPS by pressing “OFF” button for at least 0.5s, and then the buzzer will beep once.

2) Then UPS will cut off power to output and there is no display shown on the display panel.

9. Mute the buzzer

1) To mute the buzzer, please press the “Mute” button for at least 0.5s. If you press it again after the buzzer is

muted, the buzzer will beep again.

16

EN

2) Some warning alarms can’t be muted unless the error is fixed. Please refer to section 3-3 for the details.

10. Operation in warning status

1) When Fault LED flashes and the buzzer beeps once every second, it means that there are some problems

for UPS operation. Users can get the fault code from LCD panel. Please check the trouble shooting table in

chapter 4 for details.

2) Some warning alarms can’t be muted unless the error is fixed. Please refer to section 3-3 for the details.

11. Operation in Fault mode

1) When Fault LED illuminates and the buzzer beeps continuously, it means that there is a fatal error in the

UPS. Users can get the fault code from display panel. Please check the trouble shooting table in chapter

4 for details.

2) Please check the loads, wiring, ventilation, utility, battery and so on after the fault occurs. Don’t try to turn

on the UPS again before solving the problems. If the problems can’t be fixed, please contact the

distributor or service people immediately.

3) For emergency case, please cut off the connection from utility, external battery, and output immediately to

avoid more risk or danger.

12. Operation of changing battery numbers

1) This operation is only available for professional or qualified technicians.

2) Turn off the UPS. If the load couldn’t be cut off, you should remove the cover of maintenance bypass

switch on the rear panel and turn the maintenance switch to “BPS” position first.

3) Switch off the input breaker, and switch off the battery breaker (only available for long-run model).

4) Remove the cabinet, and then modify the jumper on the control board to set the battery numbers (refer to

NOTE below). Then disconnect battery wire for standard model and modify the battery pack carefully.

After complete the changes, put the cabinet back.

NOTE: JP1 setting on the control board: please shorts the Pin5 & Pin6 and Pin7 & Pin8 for 20 pcs batteries; shorts

the Pin5 & Pin6 or Pin7 & Pin8 for 19 pcs batteries; and keeps every pin open for 18 pcs batteries.

5) Switch on the input breaker and the UPS will enter Bypass mode. If the UPS is in maintenance Bypass

mode, turn the maintenance switch to “UPS” position and then turn on the UPS.

3-5. Parallel Operation

1. Parallel system connection

1) Make sure all of the UPSs are parallel models, and follow the wiring instruction in section 2-3.

2) Turn off the input and internal/external output breakers of each UPS, and turn off the battery breaker if

the UPS is long-run model.

3) Turn on the input breaker and internal output breaker of the each UPS and measure the voltage difference

between the output line1 of each UPS with multimeter. If the voltage difference is less than 1V, it means

all connections are correct. If the difference is larger than 1V, check if the wirings are connected correctly.

17

EN

4) Turn on the input breakers and internal output breakers of all UPSs in the parallel systems, and turn on

each UPS in turns. Make sure that AC mode LED or Battery mode LED displays in each UPS. Measure the

output voltage of each UPS to check if the voltage difference is less than 2V (typical 1V) with multimeter. If

the difference is more than 2V, please check that parallel cable or share current cable are connected well.

If they are all connected well, maybe it’s UPS internal issue. Please contact your local distributor or service

center for help.

5) Turn off each UPS in turns and after all of them transfer to Bypass mode, turn on the external output

breaker of each unit.

6) Turn on the UPSs in the AC mode and then the parallel system connection is complete.

2. Add one new unit into the parallel system

1) You can not add one new unit into the parallel system when whole system is running. You must cut off the

load and shutdown the system.

2) Make sure all of the UPS are the parallel models, and follow the wiring refer to section 2-3.

3) Install the new parallel system refers to the previous section.

3. Remove one unit from the parallel system

There are two methods to remove one unit from the parallel system:

First method:

1) Press the “OFF” key twice and each time should last for more than 0.5s. Then, the UPS will enter into

bypass mode without output.

2) Turn off the output breaker of this unit, and then turn off the input breaker of this unit.

3) After it shuts down, you can turn off the battery breaker (for long-run model) and remove the parallel cable

and share current cable. Then, remove the unit from the parallel system.

Second method:

1) If the bypass is abnormal, you can not remove the UPS without interruption. You must cut off the load and

shut down the system.

2) Make sure the bypass setting is enabled in each UPS and then turn off the running system. All UPSs will

transfer to Bypass mode. Remove all the maintenance bypass covers and set the maintenance switches

from “UPS” to “BPS”. Turn off the input breakers and battery breakers.

3) Remove the UPS that you want.

4) Turn on the input breaker of the remaining UPSs and the system will transfer to Bypass mode.

5) Set the maintenance switches from “BPS” to “UPS and put the maintenance bypass covers back. Turn on

the remaining UPSs and finish the parallel system connection.

Warning: (Only for the parallel system)

● Before turning on the parallel system to activate Inversor, make sure that all unit’s maintenance switch at

the same position.

● When parallel system is turned on to work through Inversor, please do not operate the maintenance switch

of any unit.

18

EN

3-6. Abbreviation Meaning in LCD Display

Abbreviation

Display content

Meaning

ENA

Enable

DIS

Disable

ATO

Auto

BAT

Battery

NCF

Normal mode (not CVCF mode)

CF

CVCF mode

SUB

Subtract

ADD

Add

ON

On

OFF

Off

FBD

Not allowed

OPN

Allow

RES

Reserved

3-7. LCD Setting

There are three parameters to set up the UPS. Refer to following diagram.

Parameter 1: It’s for program alternatives. There

are 15 programs to set up. Refer to below table.

Parameter 2 and parameter 3 are the setting

options or values for each program.

15 programs available list for parameter 1:

Code

Description

Bypass

AC

ECO

CVCF

Battery

Test

01

Output voltage

Y

02

Output frequency

Y

03

Voltage range for bypass

Y

04

Frequency range for bypass

Y

05

ECO mode enable/disable

Y

06

Voltage range for ECO mode

Y

07

ECO mode frequency range setting

Y

08

Bypass mode setting

Y

09

Battery backup time setting

Y

Parameter 1

Parameter 2

Parameter 3

19

EN

10

Programmable output setting

Y

11

Shutdown point for programmable output

Y

12

Hot standby function enable/disable

Y

13

Battery voltage adjustment

Y

14

Charger voltage adjustment

Y

15

Output voltage adjustment

Y

*Y means that this program can be set in this mode.

**Programmable output setting is not supported by 6000R(L)/10000R(L) models

Note: All parameter settings will be saved only when UPS shuts down normally with internal or external battery

connection. (Normal UPS shutdown means turning off input breaker in bypass mode).

01: Output voltage

Interface

Setting

Parameter 3: Output voltage

You may choose the following output voltage in parameter 3:

208: Presents output voltage is 208Vac

220: Presents output voltage is 220Vac

230: Presents output voltage is 230Vac

240: Presents output voltage is 240Vac

 02: Output frequency

Interface

Setting

60 Hz, CVCF mode

50 Hz, Normal mode

ATO

Parameter 2: Output Frequency

Setting the output frequency. You may choose following three options

in parameter 2:

50.0Hz: The output frequency is setting for 50.0Hz.

60.0Hz: The output frequency is setting for 60.0Hz.

ATO: If selected, output frequency will be decided according to the

latest normal utility frequency. If it is from 46Hz to 54Hz, the output

frequency will be 50.0Hz. If it is from 56Hz to 64Hz, the output

frequency will be 60.0Hz. ATO is default setting.

Parameter 3: Frequency mode

Setting output frequency at CVCF mode or not CVCF mode. You may

choose following two options in parameter 3:

CF: Setting UPS to CVCF mode. If selected, the output frequency will be

fixed at 50Hz or 60Hz according to setting in parameter 2. The input

frequency could be from 46Hz to 64Hz.

NCF: Setting UPS to normal mode (not CVCF mode). If selected, the

output frequency will synchronize with the input frequency within

46~54 Hz at 50Hz or within 56~64 Hz at 60Hz according to setting in

parameter 2. If 50 Hz selected in parameter 2, UPS will transfer to

battery mode when input frequency is not within 46~54 Hz. If 60Hz

selected in parameter 2, UPS will transfer to battery mode when input

frequency is not within 56~64 Hz.

*If Parameter 2 is ATO, the Parameter 3 will show the current

frequency.

Note: If the UPS is set to CVCF mode, the bypass function will be disabled automatically.

But when a single UPS without parallel function is powered on with mains and before the UPS finished the

startup, there will be a few seconds of voltage pulse (same as the input voltage) on the bypass output.

If you need to remove the pulse on this mode to protect your load better, you could contact the dealer for help.

For the UPS with parallel function, this pulse situation won’t happen.

La pagina sta caricando ...

PowerWalker VFI 6000R LCD Manuale del proprietario

Questo manuale è adatto anche per

PowerWalker VFI 6000R LCD Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti