Zenith Concierge H2534DT Installation And Operating Manual, Warranty

Marca: Zenith

Modello: Concierge H2534DT

Categoria: TV LCD

Tipo: Installation And Operating Manual, Warranty

Questo manuale è adatto anche per

machine numbers H1934DT H2034DT H2534DT H2539Y

installation & operating guide / warranty

Concierge

Direct View

Television Receiver

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.

Unauthorized modification could void the user’s authority to operate this product.

Concierge is a trademark of Zenith Electronics Corporation.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

PAGE 3

206-3490-O

1. Read Instructions

All the safety and operating instructions should be read

before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for

future reference.

4.Heed Warnings

All warnings on the product and in the operating instruc-

tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a

bath tub, wash bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool.

7. Accessories

Do not place this product on an unstable cart, stand, tri-

pod, bracket, or table. The product may fall, causing serious

injury to a child or adult, and serious damage to the prod-

uct. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the prod-

uct. Any mounting of the product should follow the manu-

facturer’s instructions, and should use a mounting accesso-

ry recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila-

tion and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not

be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed in

a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruc-

tions have been adhered to.

11. Power Sources

This product should be operated only from the type of

power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult

your product dealer or local power company. For products

intended to operate from battery power, or other sources,

refer to the operating instructions.

12. Line-Cord Polarization

This product is equipped with a polarized alternating-cur-

rent line plug (a plug having one blade wider than the

other). This plug will fit into the power outlet only one

way. This is a safety feature. If you are unable to insert the

plug fully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety pur-

pose of the polarized plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit

from the product.

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential

electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read

and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation

that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

PORTABLE CART WARNING

(Continued on next page)

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the

product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with

regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

16. Power Lines

An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can

result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service person-

nel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing

to qualified service personnel under the following condi-

tions:

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been

damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the man-

ufacturer or have the same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to deter-

mine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as

recommended by the manufacturer.

24. Heat

The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

PAGE 4

206-3490-O

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical

Code Instructions

NEC - National Electrical Code

IMPORTANT SAFETY INSTRUCTIONS

206-3490-O

PAGE 5

Table of Contents

Turn to the next page to begin the TV setup.

Purchase the Optional Installer’s Remote and Clone Programmer

To preform the installation setup, you need an installer’s remote like the LP702, and the LT1500 Clone Programmer - -

both are shown and described in later sections. The installer remote allows access to the Installer’s menus, User menus,

and Source/Channel Bank keys. The installer remote has Menu, Select, and Adjust Keys (Up/Down/Left/Right arrows) and

Source/Channel Bank Keys. The LT1500 Clone Programmer is used to duplicate a TV’s setup and install it on another TV.

See your Zenith Dealer.

Installer/Hotel Note:

Pages 35-38 contain information and menus which the guest can use to operate the TV. It is recom-

mended that these four pages be copied and included with the literature packet that the hotel pro-

vides to the guest.

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Important Safety Information . . . . . . . . . . . . . . . . . . .3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Step 1. Hook Up TV

TV and other Equipment Hookups

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . . .8

Cable service with VCR . . . . . . . . . . . . . . . . . . . . . . .9

External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Step 2. Channel Search and Reception Setup

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

(Select Antenna, or cable service and perform channel

search)

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . .12

Guest Remote Key Functions . . . . . . . . . . . . . . . . . . .13

Installer’s Remote Key Functions . . . . . . . . . . . . . . . .14

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . 15

Step 3. Customize the Concierge TV’s

Features

Setup Menu (Start with page 11, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Timer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Captions Caption/Text . . . . . . . . . . . . . . . . . . . . . . .20

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Installer Parental Control Menu . . . . . . . . . . . . . . . .23

Other Menus and On-Screen Displays . . . . . . . . . . . .25

Managing the Channel Banks . . . . . . . . . . . . . . . . . .26

Installers Menus . . . . . . . . . . . . . . . . . . . . . . . . . . .29

LT1500 Quickset Clone Programmer . . . . . . . . . . . . . . .32

Guest Operation Section (Copy for guest usage)

Guest Remote Control Key Functions . . . . . . . . . . . . . .35

Guest Parental Control Menu . . . . . . . . . . . . . . . . . . .36

Guest Menus and On-Screen Displays . . . . . . . . . . . . .38

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Warranty for Concierge Series TVs . . . . . . . . . . . . . . . .42

PAGE 6

206-3490-O

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of your TV.

A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws

on one end and a round opening with a wire sticking out on the other end.

Hook Up Your Antenna to the TV

Connect an off-air antenna to the Concierge TV.

If you have a 75 ohm RF cable, then you don’t need

any adapters!

Remember, when screwing RF cables onto jacks, clock-

wise tightens, and counterclockwise loosens.

A 300 to 75 ohm adapter is not included with the

Zenith Concierge TV.

Model H2539Y does not have the MPI card.

300 TO 75 OHM

ADAPTER

Antenna

TV back

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

Super

Port

SPEAKER

OUT

AUDIO

Flat wire

(300 ohm)

300/75 ohm

Adapter

TV back

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

RF coaxial wire

(75ohm)

Antenna

Super

Port

SPEAKER

OUT

AUDIO

Locate the Antenna/Cable jack on the back of your

Concierge TV.

Connect the cable that runs from the wall directly to

this jack, according to the diagram to the right.

Remove the back of the remote and put in two AA bat-

teries.

Plug in your TV. Do not plug it into a switched outlet.

Your Entertainment Machine is designed to operate on

standard current, 120-volt 60 Hertz AC. Do not attempt

to operate it on DC Current.

Go to page 11 to Auto Program your Concierge TV.

back of

remote

PAGE 7

206-3490-O

Hook Up Your Cable (CATV) to the TV

If you’re using a cable box, leave the TV on

channel 3 or 4 and use your cable box to

change channels.

Remember, when screwing RF cables onto jacks,

clockwise tightens, and counterclockwise loosens

If you’re using a cable box, Auto Program might

only find the channel your cable service is on

(usually channel 3 or 4).

Model H2539Y does not have the MPI card.

Cable TV

wall jack

RF coaxial wire (75ohm)

TV back

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

Super

Port

SPEAKER

OUT

AUDIO

RF coaxial wire (75ohm)

TV back

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

Super

Port

SPEAKER

OUT

AUDIO

Cable TV

wall jack

Cable box

Out

3 4

output

switch

Locate the Antenna/Cable jack on the back of

the Concierge TV.

Connect the cable that runs from the wall

directly to this jack, according to the diagram

to the right.

Remove the back of the remote and put in two

AA batteries.

Plug in the TV. Do not plug it into a switched

outlet. Your Concierge TV is designed to oper-

ate on household current, 120-volt 60 Hertz

AC. Do not attempt to operate it on DC

Current.

Go to page 11 to Auto Program the Concierge

TV.

back of

remote

Connect cable service to the Concierge TV.

PAGE 8

206-3490-O

Hook Up Antenna and VCR to the TV

Connect your off-air antenna and VCR to the Concierge TV.

Remember, when screwing RF cables onto jacks, clockwise

tightens, and counterclockwise loosens.

No A/V cables are included with the Zenith Concierge TV.

Model H2539Y does not have the MPI card.

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

RF coaxial wire

(75ohm)

not included

with TV

A/V cables

not included

with TV

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

Super

Port

SPEAKER

OUT

AUDIO

TV back

Flat wire

(300 ohm)

Antenna

300/75 ohm

Adapter

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

RF coaxial wire

(75ohm)

not included

with TV

A/V cables

not included

with TV

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

Super

Port

SPEAKER

OUT

AUDIO

TV back

RF coaxial wire

(75ohm)

Antenna

Locate the Antenna/Cable jack on the back of the VCR.

Connect the cable that runs from the antenna directly to

this jack, according to the diagram to the right.

Remove the back of the remote and put in two AA batter-

ies.

Plug in the TV. Do not plug it into a switched outlet. The

Concierge TV is designed to operate on standard current,

120-volt 60 Hertz AC. Do not attempt to operate it on DC

Current.

Go to page 11 to Auto Program the Concierge TV.

back of

remote

PAGE 9

206-3490-O

Hook Up Cable Service (CATV) and VCR

Connect a VCR and Cable service to the Concierge TV.

Leave the VCR and the television tuned to channel

three and use the cable box to change channels.

Remember, when screwing in RF cables onto jacks,

clockwise tightens, and counterclockwise loosens.

No A/V cables are included with your Concierge TV.

Model H2539Y does not have the MPI card.

Cable TV

wall jack

Round wire (75ohm)

Cable box

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

3 4

output

switch

RF coaxial wire

(75ohm)

not included

with TV

A/V cables

not included

with TV

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

Super

Port

SPEAKER

OUT

AUDIO

TV back

Cable TV

wall jack

Round wire (75ohm)

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

RF coaxial wire

(75ohm)

not included

with TV

A/V cables

not included

with TV

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

Super

Port

SPEAKER

OUT

AUDIO

TV back

Locate the Antenna/Cable jack on the back of the

VCR.

Connect the cable that runs from the wall directly

to this jack, according to the diagram to the

right.

Remove the back of the remote and put in two

AA batteries.

Plug in the TV. Do not plug it into a switched

outlet. The Concierge TV is designed to operate

on standard current, 120-volt 60 Hertz AC. Do not

attempt to operate it on DC Current.

Go to page 11 to Auto Program the Concierge TV.

back of

remote

PAGE 10

206-3490-O

External Speaker Hook Up

Locate the Audio In jack on the back of the

speaker.

Connect a standard audio cable from the Matrix

Out jack on the TV, to the Audio In jack on the

external speaker.

A/V cables

not included

with TV

Audio In

Speaker back

TV back

TV back panel

(expanded view)

VIDEO

ANTENNA

CABLE

M.P.I.

Super

Port

SPEAKER

OUT

AUDIO

Connect an external speaker to the Concierge TV.

PAGE 11

206-3490-O

Auto Program (Channel Search)

Use Auto Program to specify Antenna or cable service

incoming signal source and automatically store all of the

channels that are found by channel search.

With the Installer remote control in hand, press the

POWER key to turn on the Concierge TV.

Press the MENU key so the Setup menu appears.

Using SELECT on the remote control, highlight Auto

Program on the screen.

Press a Right or Left ADJ (Adjust) arrow to reach the

Auto Program screen.

Using SELECT, choose either Cable TV or Off-Air Antenna

on your screen.

Press a Right or Left ADJ arrow to begin the Channel

Search.

Press ENTER when finished.

TIMER

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

BANK

ADJ

SELECT

3/5

Mini glossary

OFF-AIR-ANTENNA If the guest can only view over-the-air broadcasts, select Antenna.

CABLE If you provide cable service to your guests, select Cable.

Note: Auto Program finds channels being received by the TV

tuner.

Cable will not work unless the lodge provides a cable service.

(If the Auto Program line appears in red, then it did not pass

one of the internal tests. To set Auto Program to white, set the

upper nibble of the EEPROM location $1FFh to $B0h.)

4/6

PAGE 12

206-3490-O

Front Panel Controls

VOL VOL

OFF

CAPTION

Press ON/OFF to turn on your Concierge TV.

To cycle through available channels, press the CHAN-

NEL UP/DOWN button.

To adjust the volume control, press the VOLUME

UP/DOWN button.

To access the Closed Captions, press the CAPTION but-

ton.

Using the front control panel to access the menus.

Typical Front Panel Controls

PAGE 13

206-3490-O

Guest Remote Key Functions

TIMER ALARM

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

FLASHBK(FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Scrolls through available channels, and the

Video Channel (Audio/Video source).

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the

Channel/Time/Audio display or to

remove any on-screen

display or menu.

NUMBER KEYPAD

Selects channels directly: enter channel num-

bers and press ENTER to go to new channel

remote control part number

SC652

124-213-02

TIMER

Press repeatedly to adjust TV turn-off

time up to 4-hours.

Picks AM/PM on the Sleep Timer menu.

VOLUME LEFT/RIGHT

Adjusts the sound levels.

CHANNEL PREVIEW

Displays the available TV channels, including

access to guest’s Parental Control menu.

Allows guest to select the Aux Channel. (Use

the Audio/Video jacks on the back of the TV

as the source of the picture and sound.)

CC(CLOSED CAPTIONING)

Press to access closed captions.

Press ENTER to exit.

A quick list of the keys on the guest remote and what they do.

ALARM

Press to display menu, then follow on-screen

instructions to set a wake-up time.

PAGE 14

206-3490-O

Installer Remote Key Functions

TIMER

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

BANK

ADJ

SELECT

FLASHBK(FLASHBACK)

Return to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Flip through available channels.

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the Channel/Time display or

to remove any on-screen display or menu.

NUMBER KEY PAD

Selects channels directly and enters

numeric values for some options

remote control part number

LP702

124-213-04

TIMER

Press repeatedly to adjust TV turn-off time

up to 4-hours.

Use to pick AM/PM in Clock/Timer menu.

VOLUME LEFT/RIGHT

Adjusts the sound levels.

CC (CLOSED CAPTIONING)

Press to access closed captions.

Press ENTER to exit.

A quick list of the keys on the LP702 installer’s remote and what they do.

BANK

Press and repeat to select a Memory Bank

- - 1, 2, 3, or 4.

MENU/SELECT/ADJ (ADJUST)

Press MENU repeatedly to scroll through

either the Installer’s, or User menus. Use

SELECT to choose an option and ADJ

(adjust) to change the selected option.

CHANNEL PREVIEW

Gives installer access to the guest’s

menus. Displays the available TV channels

and hotel guest’s Parental Control menu.

Allows user to select the Aux Channel.

(Use the Audio/Video jacks on the back

of the TV as the source of the picture and

sound.)

TV/FM

Selects TV or Radio on TVs equipped with

FM radio.

PAGE 15

206-3490-O

On-Screen Menus Overview

ON-SCREEN MENUS

SETUP MENU Adjusts the basic characteristics of the TV

Auto Program 11 Automatically finds and stores active channels to scroll through using Channel Up/Down.

Add/Del/Blnk 16 Manually picks and chooses which active channels will appear when using Channel Up/Down

Channel Labels 17 Labels your channels with their network names (ABC, CBS, HBO, etc.).

Timer Setup 18 Programs a time for the TV to turn itself on or off, or to turn itself off

after a certain amount of time.

Clock Set 19 Sets the time.

Caption/Text 20 Chooses the captioning or text option.

Language 21 Picks the language the on-screen menus will appear in.

VIDEO MENU 22 Adjusts the picture for any viewing situation. The options are: Contrast, Brightness, Color,

Tint, Sharpness, Picture Pref.

PARENTAL 23 Allows installer to block any channel or A/V source for up to 99 hours, with the use of a password.

CONTROL MENU

25 OTHER MENUS AND ON-SCREEN DISPLAYS

Channel/Time Shows the current time, channel, video and type of incoming audio signal.

Alarm Sets the wake-up time.

Sleep Timer Sets the time the TV will turn off.

Volume Shows current sound level.

Captions Use to select Caption/Text options.

Ch Preview Displays the available channels list.

Channel Bank Shows currently selected channel bank.

INSTALLER MENUS 29

Descriptions of all the menus on the TV.

Using the Menu button on the installer’s remote, the installer can access all the menus below.

Menu Name Page Description

PAGE 16

206-3490-O

Fine-tune the guest’s channel selection list.

Setting Add/Delete/Blank

Press the MENU key on the Installer’s remote so the Setup

menu appears.

Press SELECT repeatedly to highlight the Add/Del/Blnk

menu.

Using either the NUMBER keypad and ENTER or the

Channel Up/Down arrows on the remote, select a chan-

nel. (If adding a deleted channel, you will need to use

the number pad and ENTER.)

Using the Right/Left ADJ arrows, pick whether that

channel is Added, Deleted, or Blank.

To continue, select another channel and repeat Step 3.

When you are finished, press ENTER to remove menu.

Adding Aux, VCR 3, VCR 4, or FM to the

Channel Preview List

Go to the Setup menu, select the Add/Del/Blnk option.

Use Channel Up/Down to select the option and choose

Added.

Note: If the option was turned off in the Service menu,

you will have to reinstate it before it can appear as an

option in the Channel Preview list.

Notes: Adding VCR 3 and/or VCR 4 as available channels

forces TV Channel 3 and/or 4 to be retained, when run-

ning Auto Program, even though the equipment connect-

ed to the Antenna/Cable (RF) jack (like a cable convert-

er and/or VCR) may be turned off.

You can elect to Add, Delete or Blank: VCR 3, VCR 4,

and Aux. FM can be Added or Deleted, but not Blanked.

TIMER

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

BANK

ADJ

SELECT

CH 44 ADDED

Mini glossary

ADD Adds new channels to the list that the guest can scroll through when using the remote.

DELETE Removes channels for one reason or another from the list that the guest can scroll through.

BLANK Removes the video signal from a channel so the guest will only receive the audio signal.

3/5

If you delete a channel, it isn’t gone for good. Just select it

using the NUMBER keypad on the remote, or add it later.

PAGE 17

206-3490-O

Setting Up Channel Labels

Customizing the channel selection names.

TIMER

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

BANK

ADJ

SELECT

A & E

Overview

Channel Labels help the user identify the channel or network being viewed.

In the Setup menu with the CH LABELS option highlighted, use the Adjust

Left/Right arrows to scroll through the available channel labels, such as, A &

E, AMC, ESPN, HBO, etc. These are a series of alphabetically organized preset

labels from which you can choose the more common networks. Use any of

these or create custom labels.

- - - - , The 4 dashes will allow a channel label to appear; if one is provided

by XDS. (Extended data service)

NONE, prevents any channel label from appearing.

LAB 1, thru LAB 20, are the 20 programmable labels.

The 20 programmable labels can be customized for your needs.

Each programmable label has 5 characters spaces available.

To Program a Channel Label

First select a channel using the NUMBER keypad and ENTER or the Channel

Up/Down arrows, on the Installer’s remote control.

(To select a deleted channel, use the NUMBER keypad and ENTER.)

To program a channel label, go to the Setup menu and select CH LABELS.

Press the Right/Left adjust arrow to scroll the available preset labels. Scroll

past - - - -, scroll past NONE, to go to the first programmable label slot, LAB

1. Notice that the label appears with the title LAB 1, and is also on a dark

background; which will distinguish it from the preset labels.

Operating the Menu

Use Volume Up/Down to select the first letter.

Press MUTE to clear the label if necessary.

Use Channel Up/Down to change the character to one of the 255 characters

available.

Adjust Left/Right Switches to the next label.

- - moves to the next or previous

label.

Volume Up/Down Selects character spaces

- - moves to the next or previous

character space.

Channel Up/Down Scrolls through the available

characters.

ENTER Accept the channel label and

removes the menu.

MUTE Removes current label,

- - if first character space is selected.

PAGE 18

206-3490-O

Timer Set Up

The Sleep Timer may be instantly set by pressing the TIMER key

repeatedly. When you have made your selection, press ENTER to

set the Sleep Timer and return to TV viewing.

The On/Off Timer will not work until the Clock on your television

has been set.

Set times to turn the Concierge TV on or off automatically.

Be sure to set the Clock first, see next page.

With Timer Setup highlighted as shown above, press a

Left/Right ADJ arrow to display the Timer setup menu.

Use the SELECT key to pick On Time.

Use the Number keypad to enter the hours, then minutes

of the time you want the TV to turn on.

Use the TIMER key to specify AM or PM.

Use the SELECT key to pick Off Time.

Use the Number keypad to enter the hours, then minutes

of the time you want the TV to turn off.

Use the TIMER key to specify AM or PM.

Press ENTER to set the timer and return to TV viewing.

TIMER

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

BANK

ADJ

SELECT

2/5

TO SET TIMERS

Mini glossary

ON TIME The time the TV will automatically turn itself on each day.

OFF TIME The time the TV will automatically turn itself off each day.

ON/OFF TIMER Activates or deactivates the on/off timer feature.

3/6

4/7

PAGE 19

206-3490-O

The Sleep Timer may be instantly set by pressing the TIMER key

repeatedly. when you have made your selection, press ENTER to

set the timer and return to TV viewing.

The On/Off timer will not work until the Clock on your television

has been set.

Set the Clock

Set the clock on the Concierge TV.

TIMER

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

BANK

ADJ

SELECT

11:44 PM

With the Clock Set option highlighted as shown above,

press a Left/Right ADJ arrow to display the clock set

menu.

Set the current time; use the Number keypad to enter the

hours, then minutes. For example, enter 06, then 30, to set

6:30 on the clock.

Use the TIMER key to specify AM or PM.

Press ENTER to start the clock and return to TV viewing.

Mini glossary

TIME A four-digit figure broken down into hours and minutes, that is used to enter the current time when setting the clock or on/off timer.

HOURS First two digits that are entered when setting the clock, or the on/off timer.

MINUTES The last two digits that are entered when setting the clock, or the on/off timer.

PAGE 20

206-3490-O

Turns on closed-captioning or text that appears at the

bottom of the screen.

Captions come in handy when the television is on mute.

Standard closed captioning is available using the Caption 1 option.

Not all programming has closed captioning or text available.

Caption/Text

CAPTION 1

TIMER

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

BANK

ADJ

SELECT

Mini glossary

CAPTIONS The term for the words that scroll across the bottom of your TV screen; usually the audio portion of the program provided for the hearing

impaired.

TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

Caption/Text is a feature which allows the Concierge TV to receive the

closed caption and/or text options if made available by the broadcaster.

Availability and functionality of Caption/Text features is determined only

by each broadcaster and may not be available in your area.

Using SELECT on the remote control, select Captions/Text on

the screen.

Use the Right/Left ADJ arrows to choose any of the follow-

ing options: Caption 1, Caption 2, CAption 3, Caption 4,

Text 1, Text 2, Text 3, or Text 4.

Press ENTER to remove menu.

La pagina si sta caricando...

Zenith Concierge H2534DT Installation And Operating Manual, Warranty

Marca: Zenith

Modello: Concierge H2534DT

Categoria: TV LCD

Tipo: Installation And Operating Manual, Warranty

Questo manuale è adatto anche per

Scarica PDF

rapporto

in altre lingue

English: Zenith Concierge H2534DT

Zenith Concierge H2534DT Installation And Operating Manual, Warranty

Questo manuale è adatto anche per

Zenith Concierge H2534DT Installation And Operating Manual, Warranty

in altre lingue

Documenti correlati

Altri documenti