Zenith Concierge H27C35DT Istruzioni per l'uso

Marca: Zenith

Modello: Concierge H27C35DT

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

enjoy the view

installation & operating guide / warranty

table of contents

page

machine numbers H27C35DT H32C35DT

H36C35DT Concierge

TVs

RECORD TV MODEL NUMBER

The model and serial number of your new Concierge

TV are

located on the back of the TV cabinet. For your future conve-

nience, we suggest that you record these numbers here:

MODEL NO.____________________________________

SERIAL NO.____________________________________

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.

Unauthorized modification could void the user’s authority to operate this product.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Concierge

is a trademark of Zenith Electronics Corporation

2-WIRE COMM-WARN

PAGE 3

206-3489-O

1. Read Instructions

All the safety and operating instructions should be read

before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for

future reference.

4. Heed Warnings

All warnings on the product and in the operating instruc-

tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a

bath tub, wash bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool.

7. Accessories

Do not place this product on an unstable cart, stand, tri-

pod, bracket, or table. The product may fall, causing serious

injury to a child or adult, and serious damage to the prod-

uct. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the prod-

uct. Any mounting of the product should follow the manu-

facturer’s instructions, and should use a mounting accesso-

ry recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila-

tion and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not

be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed in

a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruc-

tions have been adhered to.

11. Power Sources

This product should be operated only from the type of

power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult

your product dealer or local power company. For products

intended to operate from battery power, or other sources,

refer to the operating instructions.

12. Line-Cord Polarization

This product is equipped with a polarized alternating-cur-

rent line plug (a plug having one blade wider than the

other). This plug will fit into the power outlet only one

way. This is a safety feature. If you are unable to insert the

plug fully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety pur-

pose of the polarized plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit

from the product.

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential

electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read

and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this operating guide can help you get many years of enjoyment and safe

operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

PORTABLE CART WARNING

(Continued on next page)

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the

product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with

regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

16. Power Lines

An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can

result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service person-

nel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing

to qualified service personnel under the following condi-

tions:

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been

damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the man-

ufacturer or have the same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to deter-

mine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as

recommended by the manufacturer.

24. Heat

The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

PAGE 4

206-3489-O

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical

Code Instructions

NEC - National Electrical Code

IMPORTANT SAFETY INSTRUCTIONS

206-3601-O

PAGE 5

Table of Contents

Turn to the next page to begin the TV set up

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Information . . . . . . . . . . . . . . . . . . 3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1. Hook Up TV

Hookup Directory . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TV and other Equipment Hookups

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . 9

Cable service with VCR . . . . . . . . . . . . . . . . . . . . 10

External Speaker . . . . . . . . . . . . . . . . . . . . . . . . 11

Step 2. Channel Search and Reception Setup

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

(Select Antenna, or cable service and do channel search)

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 13

Guest’s Remote Key Functions . . . . . . . . . . . . . . . . . 14

Installer’s Remote Key Functions . . . . . . . . . . . . . . . . 15

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . . 16

Step 3. Customize the TV’s Features

Setup Menu (Start with page 12, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . 17

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . 18

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . 20

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Bass, Treble, Balance, Audio Mode,

Front Surround, Sound Rite, Speakers

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.

Installer Parental Control Menu . . . . . . . . . . . . 24 - 25

Set up Parental Control

Other Menus and On-Screen Displays . . . . . . . . . . . . 26

Managing the Channel Banks . . . . . . . . . . . . 27 - 28 - 29

Installer Menus . . . . . . . . . . . . . . . . . . . . 30 - 31 - 32

LT2000 Quickset II Clone Programmer . . . . . . 33 - 34 - 35

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Guest Operation Section (Copy for guest usage)

Guest Remote Control Key Functions . . . . . . . . . . . . . 39

Guest Parental Control Menu . . . . . . . . . . . . . . . 40 - 41

Guest Menus and On-Screen Displays . . . . . . . . . . . . . 42

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Warranty for Concierge Series TVs . . . . . . . . . . Back Cover

Purchase the Optional Installer’s Remote and Clone Programmer

To preform a normal installation set up, you need an installer’s remote like the LP702, and the LT2000 Quickset II Clone

Programmer - - both are shown and described in later sections. The installer remote allows access to the Installer and,

User menus. The installer remote has Menu, Select, and Adjust keys (Down/Left/Right arrow) keys. The LT2000 Quickset

II Clone Programmer is used to duplicate a TV’s setup and install it on another identical TV. See your Zenith Dealer.

Installer/Hotel Note:

Pages 39, 40, 41, and 42 contain information and menus which the guest can use to operate the TV.

It is recommended that these four pages be copied and included with the literature packet that the

hotel provides to the guest.

Design and specifications are subject to change without prior notice.

If you are using an antenna and no other equipment, go to . . . . . . . . . . . . . . . . . . page 7

If you have cable and no other equipment, go to . . . . . . . . . . . . . . . . . . . . . . . . . page 8

If you are using an antenna and have a VCR, go to . . . . . . . . . . . . . . . . . . . . . . . page 9

If you have cable and a VCR, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10

If you want to connect a Matrix speaker, go to . . . . . . . . . . . . . . . . . . . . . . . . . . .page 11

206-3489-O

PAGE 6

Basic Hook-Up Directory

This page will direct you to which page to go to for proper hook up of the TV

IMPORTANT!!

Use this page to decide where you need to begin your set up. First, find the line below that best describes what

you want to do, then go to that page number.

Cable TV

wall jack

Cable box

Out

Cable TV

wall jack

Cable box

Out

Antenna only

Cable only

Antenna with VCR

Cable and VCR

External Speaker

Locate the Antenna/Cable jack on the back of the

TV.

Connect the cable that runs from the wall directly

to this jack, according to the diagram to the right.

Remove the back of the remote and put in two AA

batteries.

Plug in the TV. Do not plug it into a switched out-

let. The TV is designed to operate on standard cur-

rent, 120-volt 60 Hertz AC. Do not attempt to

operate it on DC Current.

Go to page 12 to Auto Program the TV.

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of your TV.

A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws

on one end and a round opening with a wire sticking out on the other end.

206-3489-O

PAGE 7

Hook Up Your Antenna to the TV

300 TO 75 OHM

ADAPTER

ANTENNA

CABLE

M.P.I.

TV back

Flat wire

(300 ohm)

Antenna

300/75 ohm

Adapter

TV back panel

(expanded view)

R- AUDIO- L

VIDEO

MATRIX

OUT

TV back

TV back panel

(expanded view)

ANTENNA

CABLE

M.P.I.

RF coaxial wire

(75ohm)

Antenna

R- AUDIO- L

VIDEO

MATRIX

OUT

back of

remote

120 V AC

60 Hz

Connect an off-air antenna to the TV

If you have a 75 ohm RF cable, then you don’t need

any adapters!

A 300 to 75 ohm adapter is not included with the

Zenith TV.

206-3489-O

PAGE 8

Hook Up Your Cable (CATV) to the TV

If you’re using a cable box, leave the TV on

channel 3 or 4 and use your cable box to

change channels.

If you’re using a cable box, Auto Program might

only find the channel your cable service is on

(usually channel 3 or 4). Don’t worry, that’s all

you need!

Cable TV

wall jack

RF coaxial wire (75ohm)

TV back

ANTENNA

CABLE

M.P.I.

R- AUDIO- L

VIDEO

MATRIX

OUT

ANTENNA

CABLE

M.P.I.

Cable TV

wall jack

Cable box

Out

RF coaxial wire (75ohm)

3 4

output

switch

TV back

R- AUDIO- L

VIDEO

MATRIX

OUT

Locate the Antenna/Cable jack on the

back of the TV.

Connect the cable that runs from the wall

directly to this jack, according to the dia-

gram to the right.

Remove the back of the remote and put in

two AA batteries.

Plug in the TV. Do not plug it into a

switched outlet. The TV is designed to

operate on household current, 120-volt 60

Hertz AC. Do not attempt to operate it on

DC Current.

Go to page 12 to Auto Program the TV.

back of

remote

120 V AC

60 Hz

Connect cable service to the TV

Locate the Antenna/Cable jack on the back of the

VCR.

Connect the cable that runs from the antenna

directly to this jack, according to the diagram to

the right. As required, make the other connections

as shown to the right.

Remove the back of the remote, put in two AA bat-

teries.

Plug in the TV. Do not plug it into a switched out-

let. The TV is designed to operate on standard cur-

rent, 120-volt 60 Hertz AC. Do not attempt to oper-

ate it on DC Current.

Go to page 12 to Auto Program the TV.

206-3489-O

PAGE 9

Hook Up Antenna and VCR to the TV

Flat wire

(300 ohm)

Antenna

300/75 ohm

Adapter

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

A/V cables

not included

with TV

TV back

R- AUDIO- L

VIDEO

MATRIX

OUT

TV back

RF coaxial wire

(75ohm)

not included

with TV

RF coaxial wire

(75ohm)

Antenna

A/V cables

not included

with TV

R- AUDIO- L

VIDEO

MATRIX

OUT

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

TV back

back of

remote

120 V AC

60 Hz

Connect an off-air antenna and VCR to the TV

No A/V cables are included with the Zenith TV.

Without A/V cables, most VCRs will not play videocas-

settes in stereo sound.

Locate the Antenna/Cable jack on the back

of the VCR.

Connect the cable that runs from the wall

directly to this jack, according to the dia-

gram to the right. As required, make the

other connections as shown to the right.

Remove the back of the remote, put in two

AA batteries.

Plug in the TV. Do not plug it into a

switched outlet. The TV is designed to oper-

ate on standard current, 120-volt 60 Hertz

AC. Do not attempt to operate it on DC

Current.

Go to page 12 to Auto Program the TV.

PAGE 10

206-3489-O

Hook Up Cable Service (CATV) and VCR

Cable TV

wall jack

Round wire (75ohm)

Cable box

Out

3 4

output

switch

A/V cables

not included

with TV

R- AUDIO- L

VIDEO

MATRIX

OUT

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

TV back

Cable TV

wall jack

Round wire (75ohm)

A/V cables

not included

with TV

R- AUDIO- L

VIDEO

MATRIX

OUT

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

TV back

back of

remote

120 V AC

60 Hz

Connect a VCR and Cable service to the TV

Leave the VCR and the television tuned to channel

three and use the cable box to change channels.

No A/V cables are included with your TV. Without

A/V cables, most VCRs will not play videocassettes

in stereo sound.

PAGE 11

206-3489-O

External Speaker Hook Up

A/V cables

not included

with TV

R- AUDIO- L

VIDEO

MATRIX

OUT

Audio In

Speaker back

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

TV back

Locate the Audio In jack on the back of the

speaker.

Connect a standard audio cable from the

Matrix Out jack on the TV, to the Audio In

jack on the external speaker.

Connect an external speaker to the TV

PAGE 12

206-3489-O

Auto Program (Channel Search)

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

3/5

4/6

Use Auto Program to specify Antenna or cable service

incoming signal source and automatically store all of the

channels that are found by channel search

With the Installer remote control in hand, press the

POWER key to turn on the TV.

Press MENU repeatedly so the Setup menu appears.

Using SELECT on the remote control, highlight Auto

Program on the screen.

Press a Right or Left ADJ (Adjust) arrow to reach the

Auto Program screen.

Using SELECT, choose either Cable TV or Off-Air Antenna

on your screen. (The flashing option is selected.)

Press a Right or Left ADJ arrow to begin the Channel

Search.

Press ENTER when finished.

Mini glossary

OFF-AIR-ANTENNA If the guest can only view over-the-air broadcasts, select Antenna.

CABLE If you provide cable service to your guests, select Cable.

Note: Auto Program finds channels being received by the TV

tuner.

Cable will not work unless the lodge provides a cable service.

PAGE 13

206-3489-O

Front Panel Controls

AUDIO

VIDEO

CAPTION

VOL VOL

OFF

LEFT

RIGHT

Typical Front Panel Controls

The Front Audio/Video jacks are a direct source con-

nection. If you have a device plugged into the front

Video jack, you will not be able to change channels

until you have unplugged the front Video jack.

Front panel control menu operation buttons are not

labeled and are not usually available to the guest.

You can use Ch to select channels and Vol to set the

volume level regardless of the key defeat setting.

There are three jacks on the front of the TV that make

connecting Audio/Video devices like camcorders very

simple.

To use the front jacks as the signal source, simply plug

a composite video cable into the VIDEO jack. The TV

will automatically change its source setting to CAM-

PORT, as indicated on the channel selection screen.

Video

Connects the video signals from any piece of

equipment.

Left/Right Audio Used for stereo sound from

various types of equipment.

Use the front control panel to access the menus or just operate the TV

Note: Item 10 Key Defeat, in the installer’s menu allows the installer to:

Set Menu Option 10, Key defeat to “0” - Front panel controls give access to menus.

Set Menu Option 10, Key defeat to “1” - Menus not available with front panel controls.

Press ON/OFF to turn on your TV.

To access the menus press the MENU button on

the control panel. Cycle through the various

menus by pushing the button repeatedly.

Press the SELECT button repeatedly to highlight

the option you want to modify.

Press either the Right or Left ADJUST button to

modify the option you have chosen.

Press CAPTIONS to turn captions on and off.

The menu will disappear after a few seconds.

PAGE 14

206-3489-O

Guest Remote Key Functions

TIMER ALARM

CHPREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

remote control part number

SC652

124-213-02

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off.

CHANNEL (UP/DOWN)

Scrolls through available channels, and the

Video Channel (Audio/Video source).

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the

Channel/Time/Audio display or to

remove any on-screen

display or menu.

NUMBER KEYPAD

Used to key-in numbers and select channels

directly: key-in channel numbers and press

ENTER to go to new channel

TIMER

Press repeatedly to set the TV turn-off

time from 10 minutes up to 4-hours.

Sets AM or PM in Clock/Alarm menus.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CHANNEL PREVIEW

Displays the available TV channels, including

access to guest’s Parental Control menu (if

Active). Allows guest to select the Video

source. (Use the Audio/Video jacks on the

back of the TV as the source of the picture

and sound.)

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the guest remote and what they do

ALARM

Press to go to the Alarm menu. Set a time for

the TV to turn itself on.

NOTE:

The channel and volume keys can be used by the guest to select and adjust the Parental

Control settings, if the installer activates the Parental Control (V-CHIP) option in the

Installer menu.

206-3489-O

PAGE 15

Installer Remote Key Functions

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

remote control part number

LP702

124-213-04

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Scrolls through available channels.

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the Channel/Time display or

to remove any on-screen display or menu.

NUMBER KEY PAD

Selects channels directly and enters

numeric values for some options

TIMER

Press repeatedly to adjust TV turn-off time

from 10 minutes up to 4-hours.

Sets AM or PM in Clock/Alarm menus.

VOLUME (LEFT/RIGHT)

Adjusts the sound levels.

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the LP702 installer’s remote and what they do

ALARM

Press to go to the Alarm menu. Set a time

for the TV to turn itself on.

MENU/SELECT/ADJ (ADJUST)

Adjusts on-screen menus and options.

Press MENU repeatedly to scroll through

menus. Use SELECT to choose an option

and ADJ (adjust) Left/Right to change

the selected option.

CHANNEL PREVIEW

Gives installer access to the guest’s

menus. Displays the available TV channels

and hotel guest’s Parental Control menu

(if active). Selects the Video source. (Use

the Audio/Video jacks on the back of the

TV as the source of the picture and

sound.)

TV/FM

Selects TV or Radio mode on TVs equipped

with FM radio.

PAGE 16

206-3489-O

On-Screen Menus Overview

ON-SCREEN MENUS

SETUP MENU Adjusts the basic operational features of the TV

Auto Program 12 Automatically finds and stores active channels to scroll through using Channel Up/Down.

Add/Del/Blnk 17 Manually picks and chooses which active channels will appear when using Channel Up/Down

Channel Labels 18 Labels the channels with their network names (ABC, CBS, HBO, etc.).

Clock Set 19 Sets the time.

Caption/Text 20 Chooses the captioning or text option.

Language 21 Picks the language the on-screen menus will appear in.

AUDIO MENU 22 Customizes the sound. Options are:

Bass, Treble, Balance, Audio Mode, Front Surround, SoundRite, Speakers.

VIDEO MENU 23 Adjusts the picture for any viewing situation. The options are: Contrast, Brightness, Color,

Tint, Sharpness, Picture Pref.

PARENTAL 24/40 Allows installer/user to block program content for up to 12 hours, with the use of a password.

CONTROL MENU

26 OTHER MENUS AND ON-SCREEN DISPLAYS

Channel/Time Shows the current time, channel, (or video source) and type of incoming audio signal.

Alarm Sets a time the TV will turn itself on.

Sleep Timer Sets a time the TV will turn off.

Volume Shows current sound level.

Captions Used to select Caption/Text options.

Ch Preview Displays the available channels and menus list.

Channel Bank Shows currently selected channel bank.

INSTALLER MENUS

Installer Menus 30 Makes adjustments to the TV’s operational features.

Descriptions of the menus and on-screen displays available to the installer

Menu Name Page Description

PAGE 17

206-3489-A

Setting Add/Delete/Blank

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

CH 44 ADDED

3/5

Fine-tune the guest’s channel selection list

Press the MENU key on the Installer’s remote so the Setup

menu appears.

Press SELECT repeatedly to highlight the Add/Del/Blnk

option.

Using either the NUMBER keypad and ENTER or the

Channel Up/Down arrows on the remote, select a chan-

nel.

(If adding a deleted channel, you will need to use the

NUMBER keypad and ENTER.)

Using the Right/Left ADJ arrows, pick whether that

channel is Added, Deleted, or Blank.

To continue, select another channel and repeat Step 3.

When you are finished, press ENTER to remove menu.

Adding Aux, VCR 3, VCR 4, or FM to the

Channel Preview List

Go to the Setup menu, select the Add/Del/BLnk option.

Use Channel Up/Down to select the option and choose

Added.

Note: If the option was turned off in the Service menu,

you will have to reinstate it before it can appear as an

option in the Channel Preview list.

Notes: Adding VCR 3 and/or VCR 4 as available channels

forces TV Channel 3 and/or 4 to be retained, when run-

ning Auto Program, even though the equipment connect-

ed to the Antenna/Cable (RF) jack (like a cable convert-

er and/or VCR) may be turned off.

You can elect to Add, Delete or Blank: VCR 3, VCR 4,

and Aux. FM can be Added or Deleted, but not Blanked.

If you delete a channel, it isn’t gone for good. Just select it

using the NUMBER keypad on the remote, or add it later.

Mini glossary

ADD Adds new channels to the list that the guest can scroll through when using the remote.

DELETE Removes channels for one reason or another from the list that the guest can scroll through.

BLANK Removes the video signal from a channel so the guest will only receive the audio signal.

PAGE 18

206-3489-A

Setting Up Channel Labels

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

A & E

Overview

Channel Labels help the user identify the channel or network being

viewed.

In the Setup menu with the CH LABELS option highlighted, use the

Adjust Left/Right arrows to scroll through the available channel labels,

such as, A & E, AMC, ESPN, HBO, etc. These are a series of alphabetically

organized preset labels from which you can choose the more common

networks. Use any of these or create custom labels.

- - - - , The 4 dashes will allow a channel label to appear; if one is pro-

vided by XDS. (Extended data service)

NONE, prevents any channel label from appearing.

LAB 1, thru LAB 20, are the 20 programmable labels.

The 20 programmable labels can be customized for your needs.

Each programmable label has 5 characters spaces available.

To Program a Channel Label

First select a channel using the NUMBER keypad and ENTER or the

Channel Up/Down arrows, on the Installer’s remote control.

(To select a deleted channel, use the NUMBER keypad and ENTER.)

To program a channel label, go to the Setup menu and select CH LABELS.

Press the Right/Left adjust arrow to scroll the available preset labels.

Scroll past - - - -, scroll past NONE, to go to the first programmable label

slot, LAB 1. Notice that the label appears with the title LAB 1, and is

also on a dark background; which will distinguish it from the preset

labels.

Operating the Menu

Use Volume Up/Down to select the first letter.

Press MUTE to clear the label if necessary.

Use Channel Up/Down to change the character to one of the 255 charac-

ters available.

Adjust Left/Right Switches to the next label.

- - moves to the next or previous

label.

Volume Up/Down Selects character spaces

- - moves to the next or previous

character space.

Channel Up/Down Scrolls through the available

characters.

ENTER Accept the channel label and

removes the menu.

MUTE Removes current label,

- - if first character space is selected.

PAGE 19

206-3601

Set the Clock

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

11:44 PM

Sets the TV’s internal clock

Press MENU repeatedly to show the Setup menu.

Press SELECT to highlight the Clock Set option.

Set the current time; use the Number keypad to enter the

hours, then minutes. For example, enter 06, then 30, to set

6:30 on the clock.

Use the TIMER key to specify AM or PM.

Press ENTER to start the clock and return to TV viewing.

Mini glossary

TIME A four-digit figure broken down into hours and minutes; first two digits are hours, last two digits are minutes.

HOURS First two digits that are entered when setting the clock.

MINUTES The last two digits that are entered when setting the clock.

TIMER Used to choose AM or PM in the clock set menu.

The Sleep Timer may be instantly set by pressing the TIMER key

repeatedly. When you have made the selection, press ENTER to

set the timer and return to TV viewing.

The clock can also be set using 24 hour “military time.” For

p.m. settings add 1200. For example, to set 6:30 p.m., add

1200 to 630, = enter 1830.

PAGE 20

206-3584

Captions (Caption/Text)

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

Standard closed captioning is available using the Caption 1 option.

CAPTION 1

CAPTION 2

CAPTION 3

CAPTION 4

TEXT 1

TEXT 2

TEXT 3

TEXT 4

OFF

TO SET CAPTIONS

CAPTIONS SETUP

OPER. MODE

SEL. TYPE

CAPTION LOCK

PRESS SELECT TO CHOOSE

PRESS ADJ TO CHANGE

STANDARD

ON, OFF

CAPTION 1

CAPTION 2

CAPTION 3

CAPTION 4

TEXT 1

TEXT 2

TEXT 3

TEXT 4

TO SET CAPTIONS

CAPTIONS SETUP

OPER. MODE

SEL. TYPE

CAPTION

ON MUTE

CAPTION LOCK

PRESS SELECT TO CHOOSE

PRESS ADJ TO CHANGE

QUICK/MUTE

ON, OFF

Mini glossary

CAPTIONS The term for the words that scroll across the bottom of your TV screen; usually the audio portion of the program

provided for the hearing impaired.

TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages

provided by the broadcaste

Caption/Text is a feature which allows the Concierge TV to receive the closed cap-

tion and/or text options if made available by the broadcaster.

Availability and functionality of Caption/Text features is determined only by each

broadcaster and may not be available in your area.

Set up Closed Caption/Text options for the user

Closed Captions/Text Operating Modes Setup

Use MENU, SELECT, and ADJ Left/Right to choose the Closed Captions/Text

mode and to set up the other menu options for the user.

Quick/Mute When CC is pressed: User can only turn Captions on/off.

(If CC on Mute is on, shows captions option on mute.)

(If locked, type is retained with Power on/off.)

Standard When CC is pressed: User can choose a captions type.

(If locked, type is retained with Power on/off.)

Press ENTER repeatedly to remove menus.

La pagina sta caricando ...

Zenith Concierge H27C35DT Istruzioni per l'uso

Marca: Zenith

Modello: Concierge H27C35DT

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Zenith Concierge H27C35DT Operating instructions

Zenith Concierge H27C35DT Istruzioni per l'uso

Questo manuale è adatto anche per

Zenith Concierge H27C35DT Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti