Edirol VMC-1 Manuale del proprietario

Marca: Edirol

Modello: VMC-1

Tipo: Manuale del proprietario

Owner’s Manual

Thank you for purchasing the Edirol VMC-1 Video Optimizer/Media

Converter.

Designed to deliver video and audio of a quality that rivals professional

equipment, the VMC-1 provides a rich array of image-correction

functionality and the capability to convert between analog and DV. It also

provides four knobs that let you quickly and easily make adjustments to the

image. Analog video such as VHS and eight-millimeter can be cleaned up

and saved to DVD-R or other media. You can also use the VMC-1 to export

analog video to a notebook computer that has only a DV connector.

Before using this unit, carefully read the sections entitled: “USING THE

UNIT SAFELY” and “IMPORTANT NOTES” (p. 2–3, p. 4). These sections

provide important information concerning the proper operation of the

unit. Additionally, in order to feel assured that you have gained a good

grasp of every feature provided by your new unit, Owner’s manual

should be read in its entirety. The manual should be saved and kept on

hand as a convenient reference.

any form without the written permission of ROLAND CORPORATION.

VMC-1(A5)_e.book 1 ページ２００５年１１月１４日　月曜日　午後２時５１分

USING THE UNIT SAFELY

001

• Before using this unit, make sure to read the

instructions below, and the Owner’s

Manual.

..................................................................................................

002c

• Do not open (or modify in any way) the unit

or its AC adaptor.

..................................................................................................

003

• Do not attempt to repair the unit, or replace

parts within it (except when this manual

provides specific instructions directing you

to do so). Refer all servicing to your retailer,

the nearest Roland Service Center, or an

authorized Roland distributor, as listed on

the “Information” page.

..................................................................................................

004

• Never use or store the unit in places that

are:

• Subject to temperature extremes (e.g.,

direct sunlight in an enclosed vehicle,

near a heating duct, on top of heat-gener-

ating equipment); or are

• Damp (e.g., baths, washrooms, on wet

floors); or are

• Humid; or are

• Exposed to rain; or are

• Dusty; or are

• Subject to high levels of vibration.

..................................................................................................

007

• Make sure you always have the unit placed

so it is level and sure to remain stable.

Never place it on stands that could wobble,

or on inclined surfaces.

008c

• Be sure to use only the AC adaptor supplied

with the unit. Also, make sure the line

voltage at the installation matches the input

voltage specified on the AC adaptor’s body.

Other AC adaptors may use a different

polarity, or be designed for a different

voltage, so their use could result in damage,

malfunction, or electric shock.

..................................................................................................

008e

• Use only the attached power-supply cord.

Also, the supplied power cord must not be

used with any other device.

..................................................................................................

009

• Do not excessively twist or bend the power

cord, nor place heavy objects on it. Doing so

can damage the cord, producing severed

elements and short circuits. Damaged cords

are fire and shock hazards!

..................................................................................................

010

• This unit, either alone or in combination

with an amplifier and headphones or

speakers, may be capable of producing

sound levels that could cause permanent

hearing loss. Do not operate for a long

period of time at a high volume level, or at a

level that is uncomfortable. If you

experience any hearing loss or ringing in the

ears, you should immediately stop using the

unit, and consult an audiologist.

..................................................................................................

011

• Do not allow any objects (e.g., flammable

material, coins, pins); or liquids of any kind

(water, soft drinks, etc.) to penetrate the

unit.

Used for instructions intended to alert

the user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic

animals or pets.

Used for instructions intended to alert

the user to the risk of death or severe

injury should the unit be used

improperly.

The ● symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In

the case of the symbol at left, it means that the power-

cord plug must be unplugged from the outlet.

The symbol alerts the user to important instructions

or warnings.The specific meaning of the symbol is

determined by the design contained within the

triangle. In the case of the symbol at left, it is used for

general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never

be carried out (are forbidden). The specific thing that

must not be done is indicated by the design contained

within the circle. In the case of the symbol at left, it

means that the unit must never be disassembled.

VMC-1(A5)_e.book 2 ページ２００５年１１月１４日　月曜日　午後２時５１分

012b

• Immediately turn the power off, remove the

AC adaptor from the outlet, and request

servicing by your retailer, the nearest

Roland Service Center, or an authorized

Roland distributor, as listed on the “Infor-

mation” page when:

• The AC adaptor, the power-supply cord,

or the plug has been damaged; or

• If smoke or unusual odor occurs

• Objects have fallen into, or liquid has

been spilled onto the unit; or

• The unit has been exposed to rain (or

otherwise has become wet); or

• The unit does not appear to operate

normally or exhibits a marked change in

performance.

..................................................................................................

013

• In households with small children, an adult

should provide supervision until the child is

capable of following all the rules essential

for the safe operation of the unit.

..................................................................................................

014

• Protect the unit from strong impact.

(Do not drop it!)

..................................................................................................

015

• Do not force the unit’s power-supply cord

to share an outlet with an unreasonable

number of other devices. Be especially

careful when using extension cords—the

total power used by all devices you have

connected to the extension cord’s outlet

must never exceed the power rating (watts/

amperes) for the extension cord. Excessive

loads can cause the insulation on the cord to

heat up and eventually melt through.

..................................................................................................

016

• Before using the unit in a foreign country,

consult with your retailer, the nearest

Roland Service Center, or an authorized

Roland distributor, as listed on the “Infor-

mation” page.

101b

• The unit and the AC adaptor should be

located so their location or position does not

interfere with their proper ventilation.

..................................................................................................

102c

• Always grasp only the plug on the AC

adaptor cord when plugging into, or

unplugging from, an outlet or this unit.

..................................................................................................

103b

• At regular intervals, you should unplug the

AC adaptor and clean it by using a dry cloth

to wipe all dust and other accumulations

away from its prongs. Also, disconnect the

power plug from the power outlet

whenever the unit is to remain unused for

an extended period of time. Any accumu-

lation of dust between the power plug and

the power outlet can result in poor

insulation and lead to fire.

..................................................................................................

104

• Try to prevent cords and cables from

becoming entangled. Also, all cords and

cables should be placed so they are out of

the reach of children.

..................................................................................................

106

• Never climb on top of, nor place heavy

objects on the unit.

..................................................................................................

107c

• Never handle the AC adaptor or its plugs

with wet hands when plugging into, or

unplugging from, an outlet or this unit.

..................................................................................................

108b

• Before moving the unit, disconnect the AC

adaptor and all cords coming from external

devices.

..................................................................................................

109b

• Before cleaning the unit, turn off the power

and unplug the AC adaptor from the outlet

(p. 28).

..................................................................................................

110b

• Whenever you suspect the possibility of

lightning in your area, disconnect the AC

adaptor from the outlet.

..................................................................................................

118

• Should you remove a screw of the ground

terminal, make sure to put them in a safe

place out of children's reach, so there is no

chance of them being swallowed acciden-

tally.

VMC-1(A5)_e.book 3 ページ２００５年１１月１４日　月曜日　午後２時５１分

IMPORTANT NOTES

291a

In addition to the items listed under “USING THE UNIT SAFELY” on page 2–3, please read and

observe the following:

Power Supply

301

• Do not use this unit on the same power circuit with

any device that will generate line noise (such as an

electric motor or variable lighting system).

302

• The AC adaptor will begin to generate heat after

long hours of consecutive use. This is normal, and is

not a cause for concern.

307

• Before connecting this unit to other devices, turn off

the power to all units. This will help prevent

malfunctions and/or damage to speakers or other

devices.

Placement

351

• Using the unit near power amplifiers (or other

equipment containing large power transformers)

may induce hum. To alleviate the problem, change

the orientation of this unit; or move it farther away

from the source of interference.

352a

• This device may interfere with radio and television

reception. Do not use this device in the vicinity of

such receivers.

352b

• Noise may be produced if wireless communications

devices, such as cell phones, are operated in the

vicinity of this unit. Such noise could occur when

receiving or initiating a call, or while conversing.

Should you experience such problems, you should

relocate such wireless devices so they are at a

greater distance from this unit, or switch them off.

354a

• Do not expose the unit to direct sunlight, place it

near devices that radiate heat, leave it inside an

enclosed vehicle, or otherwise subject it to temper-

ature extremes. Excessive heat can deform or

discolor the unit.

355b

• When moved from one location to another where

the temperature and/or humidity is very different,

water droplets (condensation) may form inside the

unit. Damage or malfunction may result if you

attempt to use the unit in this condition. Therefore,

before using the unit, you must allow it to stand for

several hours, until the condensation has completely

evaporated.

Maintenance

401a

• For everyday cleaning wipe the unit with a soft, dry

cloth or one that has been slightly dampened with

water. To remove stubborn dirt, use a cloth impreg-

nated with a mild, non-abrasive detergent. After-

wards, be sure to wipe the unit thoroughly with a

soft, dry cloth.

402

• Never use benzine, thinners, alcohol or solvents of

any kind, to avoid the possibility of discoloration

and/or deformation.

Additional Precautions

553

• Use a reasonable amount of care when using the

unit’s buttons, sliders, or other controls; and when

using its jacks and connectors. Rough handling can

lead to malfunctions.

556

• When connecting / disconnecting all cables, grasp

the connector itself—never pull on the cable. This

way you will avoid causing shorts, or damage to the

cable’s internal elements.

557

•A small amount of heat will radiate from the unit

during normal operation.

558b

• To avoid disturbing your neighbors, try to keep the

unit’s volume at reasonable levels (especially when

it is late at night).

559a

• When you need to transport the unit, package it in

the box (including padding) that it came in, if

possible. Otherwise, you will need to use equivalent

packaging materials.

Add

• This product is compatible with regular NTSC or

PAL video signal. In case irregular signal is input, it

may obstruct stabile operation of this product.

562

• If using some other make of connection cable, please

note the following precautions.

• Some connection cables contain resistors. Do not

use cables that incorporate resistors for

connecting to this unit. The use of such cables can

cause the sound level to be extremely low, or

impossible to hear. For information on cable

specifications, contact the manufacturer of the

cable.

851

• Unauthorized recording, distribution, sale, lending,

public performance, broadcasting, or the like, in

whole or in part, of a work (musical composition,

video, broadcast, public performance, or the like)

whose copyright is held by a third party is

prohibited by law.

853

• Do not use this unit for purposes that could infringe

on a copyright held by a third party. We assume no

responsibility whatsoever with regard to any

infringements of third-party copyrights arising

through your use of this unit.

VMC-1(A5)_e.book 4 ページ２００５年１１月１４日　月曜日　午後２時５１分

Contents

USING THE UNIT SAFELY ..................................................................... 2

IMPORTANT NOTES............................................................................... 4

Main Features ......................................................................................... 6

Names of Things and What They Do .................................................... 8

Front Panel....................................................................................................................8

Rear Panel ...................................................................................................................10

Bottom Panel (DIP Switches) ...................................................................................11

Deutsch

Bezeichnung und Funktion der Komponenten.................................. 12

Vorderseite..................................................................................................................12

Bedienungselemente auf der Rückseite..................................................................14

Unterseite (DIP-Schalter)..........................................................................................15

Français

Description............................................................................................ 16

Face avant ...................................................................................................................16

Face arrière..................................................................................................................18

Face inférieure (commutateurs DIP).......................................................................19

Italiano

Nomi delle cose e loro funzioni........................................................... 20

Pannello Pa .................................................................................................................20

Pannello posteriore....................................................................................................22

Pannello Inferiore (Interruttori DIP).......................................................................23

Español

Nombres de los diferentes elementos y sus funciones ................... 24

Panel frontal................................................................................................................24

Panel posterior ...........................................................................................................26

Panel inferior (Interruptores DIP)...........................................................................27

Setup and Connections ....................................................................... 28

Turning the Power On/Off......................................................................................28

Recording Video from a Video Tape to Your DVD Recorder............ 29

Capturing Video from a Video Tape into Your Computer................. 30

Watching Video from Your Computer on a Television ..................... 31

Appendix ............................................................................................... 32

Color Bar Output .......................................................................................................32

About Copy-protected Video...................................................................................32

Troubleshooting.........................................................................................................32

Specifications..............................................................................................................34

Index ...................................................................................................... 35

VMC-1(A5)_e.book 5 ページ２００５年１１月１４日　月曜日　午後２時５１分

Main Features

Provides a resolution of 10 bits for video decoding and encoding, and 24 bits for audio AD/

DA conversion. It also has a Locked Audio function, which prevents video and audio from

drifting out of synchronization. (p. 11)

* The Locked Audio function is available only for analog input.

Differences in camera settings, type, shooting conditions, and shooting technique can

produce inconsistencies in the hue and brightness of a video image. Also, analog video that

was captured some time ago can often be lacking in vividness of color. When dubbing from

analog to analog or from analog to DV or DVD, it is very effective to use the VMC-1’s image

correction functionality (brightness, intensity, hue, contrast) to minimize such

inconsistencies in the image and improve the overall quality. You can use the knobs to make

these adjustments in real time while watching the video. (p. 9)

* Available only for analog input.

TBC is a function that cleans up the video image by eliminating the “jitter” (horizontal

shaking) caused by inaccuracies in head or tape rotation during analog videotape playback,

or due to degradation of the analog video signal. This function is very useful if you are

digitizing the video tape library you have collected over the years. You can also apply delay

to the audio to correct any timing discrepancies between the video and audio that might be

caused by the TBC. You can use a front panel button to switch this function on/off. (p. 8)

* Available only for analog input.

This function determines whether the image is moving or stationary, and if stationary,

compares the same scan lines of the preceding and following frames to separate the

brightness and color signals with high precision. This allows smearing to be reduced,

minimizing unwanted noise or blurring. You can use a front panel button to switch this

function on/off. (p. 9)

* Available only for composite input in NTSC mode.

Designed for High Quality Video and Audio, with 10-bit Video

AD/DA Conversion and 24-bit Audio AD/DA Conversion

Make Corrections in Real Time While Watching the Image

TBC (Time Base Corrector) for Stabilizing Unstable Images

Motion Adaptive 3D Y/C Separator to Reduce Color Smearing

and Graininess

VMC-1(A5)_e.book 6 ページ２００５年１１月１４日　月曜日　午後２時５１分

Main Features

This function corrects inaccuracies in the timing of the video signal. Due to the mechanical

characteristics of consumer analog video decks, the preceding or following frame can

sometimes be output “out of step.” The Frame Synchronizer corrects slight inaccuracies of

the synchronization signal to prevent frame dropouts and audio dropouts. (p. 8)

* This will automatically turn on only when you use analog input.

The image from a consumer analog video camera or dubbed video tape sometimes does not

have the optimal brightness. If such an image is digitized, over-exposed whites or under-

exposed blacks may occur. AGC corrects these problems by automatically optimizing the

brightness of the analog video. You can use a front panel button to switch this function on/

off. (p. 9)

* Available only for analog input.

* Correction is not possible if the input video already has over-exposed whites or under-exposed blacks.

* You cannot convert from NTSC to PAL or vice versa.

* 16:9 screen mode is not supported.

Each set provides an S-video jack and a composite video jack, and they are capable of

providing simultaneous output. Analog input -> analog output is also supported, allowing

conversion between S-video connector <-> video jack (composite).

Frame Synchronizer Prevents Frame Dropouts and Audio

Dropouts

AGC Function Corrects Over-Exposed Whites or Under-

Exposed Blacks

Support for Both NTSC and PAL

Two Sets of Analog Output Jacks Provided

VMC-1(A5)_e.book 7 ページ２００５年１１月１４日　月曜日　午後２時５１分

Names of Things and What They Do

1. DV connector 2 [DV2 IN/OUT]

Connect your DV device or computer here.

* You cannot use this simultaneously with the DV connector 1 on the VMC-1’s rear panel (p. 10). If

you attempt to use both simultaneously, your DV device may not function correctly.

2. DV input button [DV IN]

Turn this on if you want the video and audio signals from your DV device to be sent from

the analog output.

3. Analog input button [ANALOG IN]

Turn this on if you want the video and audio signals from the analog input to be sent from

the analog output.

4. Frame synchronizer indicator [FRAME SYNC]

This indicator will light when an analog video signal is input. The frame synchronizer

corrects synchronization inaccuracies caused by an unstable video signal, preventing lost

frames and audio dropouts.

5. Time base corrector button [TBC]

This corrects the image jitter that often occurs when an analog video deck is playing back.

Normally, you should leave this on. If this is on, the video and audio signals will be output

with a delay compared to the input signal, in order to allow for this processing to be

performed. If this delay is a problem, you can turn this function off.

Front Panel

VMC-1(A5)_e.book 8 ページ２００５年１１月１４日　月曜日　午後２時５１分

Español Italiano Français Deutsch English

Names of Things and What They Do

6. Three-D Y/C separation button [3D Y/C]

This is available only in NTSC mode (p. 11). This will reduce certain problems that may

occur when a composite signal is being input, such as fine diagonal black and white stripes

producing a rainbow-like effect (cross color) or the appearance of small white and black dots

outlined in black (dot interference), and will clean up the signal by reducing color smearing.

Normally, you should leave this on. If there is a great deal of movement in the image, this

may cause blurring. If so, turn this off. If this is off, 2-D Y/C separation is applied.

* In PAL mode 2-D Y/C separation is always applied, so this button will be disabled.

7. Automatic brightness adjustment button [AGC]

This corrects the over-exposed whites or under-exposed blacks that can occur if the

brightness of the image is not appropriate. Normally, you should leave this on.

* Correction is not possible if the input video already has over-exposed whites or under-exposed blacks.

8. Audio level indicator

The green indicator will light when an analog audio signal is input. The red indicator will

light if the input level is excessive. Lower the audio input level until the red indicator does

not light.

9. Power button [POWER]

10. Brightness knob [BRIGHT]

Turn this knob toward the right to brighten the image, or toward the left to darken the

image.

11. Color depth knob [COLOR]

Turn this knob toward the right to deepen the color, or toward the left to lighten the color.

12. Color hue knob [HUE]

Turn this knob toward the right to give the image a more greenish hue, or toward the left to

give it a more purple hue.

13. Contrast knob [CONTRAST]

Turn this knob toward the right to make the contrast stronger, or toward the left to decrease

it.

14. Audio input level knob [AUDIO LEVEL]

Turn this knob toward the right to increase the audio input level.

* When a DV signal is input, buttons/knobs/indicators 4.–8. and 10.–14. are disabled. These functions

apply only to analog input signals.

* When a DV signal is input, the indicators of each button and the illumination around the knobs will

go out.

VMC-1(A5)_e.book 9 ページ２００５年１１月１４日　月曜日　午後２時５１分

Names of Things and What They Do

1. AC adaptor jack

Connect the included AC adaptor here.

2. Ground Terminal (p. 28)

3. Analog output jacks 1/2 [ANALOG OUTPUT 1/2]

These are analog output jacks for video and audio. Connect them to your monitor television,

DVD recorder, or video deck.

4. Analog input jack [ANALOG INPUT]

This is an analog video/audio jack. Connect it to your VHS or 8mm video deck.

* If video cables are connected to both the S-video input jack and the composite input jack, the S-video

input will take priority.

5. DV connector 1 [DV1 IN/OUT]

Connect this to your DV device or computer.

* Do not use this simultaneously with the DV connector 2 located on the front panel of the VMC-1 (p.

8). If you use the two simultaneously, your DV device may not work correctly.

6. Security Slot ( )

http://www.kensington.com/

Rear Panel

VMC-1(A5)_e.book 10 ページ２００５年１１月１４日　月曜日　午後２時５１分

Español Italiano Français Deutsch English

Names of Things and What They Do

1. Video format setting switch [Video Format]

Specifies the video signal format.

2. NTSC setup level setting switch [NTSC Setup Level]

Specifies the NTSC setup level.

Select 0IRE in Japan, and select 7.5IRE in North America.

3. Locked Audio mode setting switch [Locked Audio Mode]

Specifies the Locked Audio mode for analog input.

4. Audio format setting switch [Audio Format]

Specifies the audio sampling rate and bit depth when using analog input.

5. Audio mix mode setting switch [Audio Mix Mode]

Specifies whether the sub-channels will be output when you input 32 kHz/12-bit 4-channel

audio format via DV.

6. Audio muting time setting switch

Depending on the video editing software you’re using, you may experience audio noise at the

beginning of playback if this switch is turned

. In this case, use the

OFF

setting.

* When the VMC-1 is shipped from the factory, DIP switch 6 is turned

OFF

Make sure to turn off the power before you change the settings of the DIP switches on the

bottom panel.

Bottom Panel (DIP Switches)

OFF

NTSC

ON PAL

OFF 0IRE

ON 7.5IRE

OFF Locked

ON Unlocked

OFF 48kHz/16bit

ON 32kHz/12bit

OFF Main only

ON Mix 50% main + 50% sub

OFF Normal

ON Short

SER.NO.SER.NO.

MODELMODEL

VMC

1VMC

MADE IN JAPANMADE IN JAPAN

OFF ON

1Video Format NTSC PAL

OFF ON

2 NTSC Setup Level 0 IRE 7.5 IRE

3 Locked Audio Mode LOCKED UNKOCKED

4 Audio Format 48kHz /

16bit 32kHz /

12bit

5 Audio Mix Mode MAIN MAIN

SUB

6 Reserved

OFF ON

VMC-1(A5)_e.book 11 ページ２００５年１１月１４日　月曜日　午後２時５１分

Bezeichnung und Funktion der

Komponenten

1. DV-Anschluss 2 [DV2 IN/OUT]

Schließen Sie Ihr DV-Gerät oder Ihren Computer hier an.

* Sie können diesen Anschluss nicht gleichzeitig mit dem DV-Anschluss 1 an der Rückseite des VMC-1

benutzen (p. 14). Wenn Sie versuchen, beide Anschlüsse simultan zu nutzen, kann es sein, dass Ihr

DV-Gerät nicht einwandfrei funktioniert.

2. DV Input-Taste [DV IN]

Drücken Sie diese Taste, wenn die Video- und Audiosignale Ihres DV-Geräts vom analogen

Output gesendet werden sollen.

3. Analog Input-Taste [ANALOG IN]

Drücken Sie diese Taste, wenn die Video- und Audiosignale des analogen Inputs vom

analogen Output gesendet werden sollen.

4. Bildsynchronisationsanzeige [FRAME SYNC]

Diese Anzeige leuchtet, wenn ein analoges Videosignal am Input anliegt. Die Bildsynchroni-

sation korrigiert Synchronfehler, die durch instabile Videosignale verursacht werden und

beugt Bild- und Tonverlusten vor.

5. Time-base-corrector Taste [TBC]

Korrigiert das Bildflimmern, das oft bei der Wiedergabe von analogen Videogeräten auftritt.

Normalerweise sollte der Time-base-corrector eingeschaltet sein. Die Video- und Audiosi-

gnale werden dann im Vergleich mit dem Input-Signal verzögert ausgegeben, damit die

Korrektur erfolgen kann. Wenn diese Verzögerung ein Problem darstellt, können Sie diese

Funktion ausschalten.

6. Drei-D Y/C Trenntaste [3D Y/C]

Diese Funktion ist nur in der NTSC-Betriebsart wirksam (p. 15). Hierdurch werden Probleme

reduziert, die entstehen können, wenn ein zusammengesetztes Signal ausgegeben wird,

beispielsweise feine diagonale schwarze und weiße Streifen, die einen Regenbogeneffekt

(Kreuzfarben) verursachen können, oder wenn kleine weiße und schwarze Punkte mit

Vorderseite

VMC-1(A5)_e.book 12 ページ２００５年１１月１４日　月曜日　午後２時５１分

Español Italiano Français Deutsch English

Bezeichnung und Funktion der Komponenten

schwarzer Umrandung (Punktinterferenz) dargestellt werden. Das Signal wird gereinigt und

Farbverschmierungen werden reduziert. Normalerweise sollte diese Funktion eingeschaltet

sein. Wenn viele Bewegungen im Bild vorhanden sind, kann dies Unschärfe verursachen. Dann

sollte diese Funktion ausgeschaltet werden. Statt dessen wird 2-D Y/C Trennung verwendet.

* In der PAL-Betriebsart wird immer 2-D Y/C Trennung verwendet, die Taste ist daher außer Funktion.

7. Taste automatische Helligkeitsregelung [AGC]

Hierdurch werden weiße Streifen oder schwarze Gitter korrigiert, die entstehen können,

wenn die Helligkeit des Bildes nicht korrekt eingestellt ist. Normalerweise sollte diese

Funktion eingeschaltet sein.

* Eine Korrektur ist nicht möglich, wenn das Videoeingangssignal bereits weiße Streifen oder schwarze

Gitter aufweist.

8. Audiopegelanzeige

Die grüne Anzeige leuchtet, wenn ein analoges Audiosignal am Input anliegt. Die rote

Anzeige leuchtet, wenn der Eingangspegel zu hoch ist. Reduzieren Sie den Eingangspegel,

bis die rote Anzeige nicht mehr leuchtet.

9. EIN/AUS-Taste [POWER]

10. Helligkeitsregler [BRIGHT]

Durch Drehen nach rechts wird das Bild heller, durch Drehen nach links wird es dunkler.

11. Farbtiefenregler [COLOR]

Durch Drehen nach rechts werden die Farben dunkler, durch Drehen nach links werden sie

heller.

12. Farbtonregler [HUE]

Durch Drehen nach rechts erhält das Bild einen stärker grünlichen Farbton, durch Drehen

nach links einen stärker violetten Farbton.

13. Kontrastregler [CONTRAST]

Durch Drehen nach rechts wird der Kontrast verstärkt, durch Drehen nach links wird er reduziert.

14. Regler für Audio-Inputpegel [AUDIO LEVEL]

Durch Drehen nach rechts erhöhen Sie den Audio-Inputpegel.

* Wenn ein DV-Signal anliegt, sind die Tasten/Regler/Anzeigen 4. bis 8. sowie 10. bis 14. außer

Funktion. Diese Funktionen beziehen sich nur auf analoge Eingangssignale.

* Wenn ein DV-Signal am Eingang anliegt, erlöschen die Anzeigen und Beleuchtungen der Tasten und

Regler.

VMC-1(A5)_e.book 13 ページ２００５年１１月１４日　月曜日　午後２時５１分

Bezeichnung und Funktion der Komponenten

1. Anschlussbuchse für Netzgerät

Hier schließen Sie das Kabel des mitgelieferten Netzgerätes an.

2. Erdungsterminal

3. Analoge Ausgangsbuchsen 1/2 [ANALOG OUTPUT 1/2]

Analoge Ausgangsbuchsen für Video und Audio. Schließen Sie diese an Ihr TV-Gerät, DVD-

Gerät oder Videorecorder an.

4. Analoge Eingangsbuchsen [ANALOG INPUT]

Dies ist eine analoge Video/Audio-Buchse. Schließen Sie diese an Ihren VHS- oder 8mm-

Videorecorder an.

* Wenn Videokabel sowohl an die S-Video-Eingangsbuchse als auch an die Kombi-Eingangsbuchse

angeschlossen sind, hat der S-Video-Eingang Priorität.

5. DV-Anschluss 1 [DV2 IN/OUT]

Schließen Sie diesen an Ihr DV-Gerät oder an Ihren Computer an.

* Verwenden Sie diesen Anschluss nicht gleichzeitig mit dem DV-Anschluss 2 an der Vorderseite des

VMC-1 (p. 12). Wenn Sie beide Anschlüsse simultan nutzen, kann es sein, dass Ihr DV-Gerät nicht

einwandfrei funktioniert.

6. Sicherheitsschlitz ( )

http://www.kensington.com/

Bedienungselemente auf der Rückseite

VMC-1(A5)_e.book 14 ページ２００５年１１月１４日　月曜日　午後２時５１分

Español Italiano Français Deutsch English

Bezeichnung und Funktion der Komponenten

1. Schalter für Videoformateinstellung [Video Format]

Zur Einstellung des Videosignalformats.

2. Schalter für NTSC-Setup-Level [NTSC Setup Level]

Zur Einstellung des NTSC-Setup-Level.

Zur Einstellung von 0IRE in Japan und von 7.5IRE in Nordamerika.

3. Schalter für Audio-Modus-Einstellung [Locked Audio Mode]

Zur Einstellung des Locked-Audio-Modus für den analogen Input.

4. Schalter für Audioformat-Einstellung [Audio Format]

Zur Einstellung der Audiosamplingrate und der Bittiefe bei analogen Eingängen.

5. Schalter für Audiomix-Moduseinstellung [Audio Mix Mode]

Bestimmt, ob die Unterkanäle ausgegeben werden, wenn 32 kHz/12-Bit 4-Kanalaudio-

formate über DV am Input anliegen.

6. Audiostummschaltung-Einstellschalter

Je nach der verwendeten Video-Schnittsoftware können Sie Tonrauschen am Anfang der

Wiedergabe feststellen, wenn dieser Schalter auf ON gestellt ist. In diesem Fall stellen Sie ihn

auf OFF.

* Werkseitig ist beim VMC-1 der DIP-Schalter 6 auf OFF gestellt.

Bevor Sie die Einstellungen der DIP-Schalter an der Unterseite ändern, müssen Sie das

Gerät ausschalten.

Unterseite (DIP-Schalter)

OFF

NTSC

ON PAL

OFF 0IRE

ON 7.5IRE

OFF Locked

ON Unlocked

OFF 48kHz/16bit

ON 32kHz/12bit

OFF Main only

ON Mix 50% main + 50% sub

OFF Normal

ON Kurz

SER.NO.SER.NO.

MODELMODEL

VMC

1VMC

MADE IN JAPANMADE IN JAPAN

OFF ON

1Video Format NTSC PAL

OFF ON

2 NTSC Setup Level 0 IRE 7.5 IRE

3 Locked Audio Mode LOCKED UNKOCKED

4 Audio Format 48kHz /

16bit 32kHz /

12bit

5 Audio Mix Mode MAIN MAIN

SUB

6 Reserved

OFF ON

VMC-1(A5)_e.book 15 ページ２００５年１１月１４日　月曜日　午後２時５１分

Description

1. Connecteur DV 2 [DV2 IN/OUT]

Connexion pour appareil DV ou ordinateur.

* Pas d’utilisation simultanée avec le connecteur DV 1 de la face arrière du VMC-1 (p. 18) En cas

d’utilisation simultanée, l’appareil DV risque de ne pas fonctionner correctement.

2. Bouton d’entrée DV [DV IN]

L’activation de cette fonction permet d’envoyer les signaux audio et vidéo de votre appareil

DV à partir de la sortie analogique.

3. Bouton d’entrée analogique [ANALOG IN]

L’activation de cette fonction permet d’envoyer les signaux audio et vidéo de l’entrée analo-

gique à partir de la sortie analogique.

4. Indicateur de synchronisation d’images [FRAME SYNC]

Cet indicateur s’allume lorsqu’un signal vidéo analogique arrive en entrée. Le synchroniseur

d’images corrige les imprécisions dues à l’instabilité du signal vidéo, et empêche la perte

d’images ou les drop-outs audio.

5. Bouton de correction du temps [TBC]

Cette fonction corrige l’instabilité de l’image, fréquente à la lecture avec un magnétoscope

analogique. En principe, cette option reste activée. Lorsqu’elle est activée, les signaux audio

et vidéo sortent en retard par rapport au signal d’entrée pour permettre leur traitement. Si ce

retard pose un problème, la fonction peut être désactivée.

Face avant

VMC-1(A5)_e.book 16 ページ２００５年１１月１４日　月曜日　午後２時５１分

Español Italiano Français Deutsch English

Description

6. Bouton de séparation Y/C trois D [3D Y/C]

Disponible uniquement en mode NTSC (p. 19). Réduit une série de problèmes pouvant se

présenter lorsqu’un signal composite arrive en entrée, par exemple de fines rayures diago-

nales en noir et blanc produisant un effet d’arc-en-ciel (battement couleur) ou l’apparition de

petits points noirs et blancs entourés de noir (interférence ponctuelle), et nettoie le signal en

réduisant la bavure des couleurs. En principe, cette option reste activée. Si l’image comporte

beaucoup de mouvement, elle peut apparaître floue. Dans ce cas, désactiver la fonction ; la

séparation Y/C 2-D est alors appliquée.

* En mode PAL, la séparation Y/C 2-D est toujours appliquée ; ce bouton n’a donc aucun effet.

7. Bouton d’ajustage automatique de la luminosité [AGC]

Ce bouton corrige les stries blanches et les barres noires pouvant se produire lorsque la

luminosité de l’image n’est pas appropriée. En principe, cette option reste activée.

* La correction n’est pas possible si la vidéo d’entrée comporte déjà des stries blanches ou des barres

noires.

8. Indicateur de niveau audio

Le témoin vert s’allume lorsqu’un signal audio analogique arrive en entrée. Le témoin rouge

s’allume si le niveau d’entrée est excessif. Réduire le niveau d’entrée audio jusqu’à extinction

du témoin rouge.

9. Bouton de mise sous tension [POWER]

10. Bouton de luminosité [BRIGHT]

Tourner ce bouton vers la droite pour éclaircir l’image, ou vers la gauche pour l’assombrir.

11. Bouton de saturation des couleurs [COLOR]

Tourner ce bouton vers la droite pour des couleurs plus saturées, ou vers la gauche pour des

couleurs plus légères.

12. Bouton de teinte des couleurs [HUE]

Tourner ce bouton vers la droite pour une image plus verdâtre, ou vers la gauche pour des

teintes plus pourpre.

13. Bouton de contraste [CONTRAST]

Tourner ce bouton vers la droite pour augmenter le contraste, ou vers la gauche pour le

réduire.

14. Bouton de niveau d’entrée audio [AUDIO LEVEL]

Tourner ce bouton vers la droite pour augmenter le niveau d’entrée audio.

* Lorsqu’un signal DV parvient en entrée, les boutons/molettes/témoins 4.-8. et 10.-14. sont désactivés.

Ces fonctions ne s’appliquent qu’aux signaux d’entrée analogiques.

* En cas d’entrée d’un signal DV, les témoins de chaque bouton et l’éclairage autour des boutons

s’éteint.

VMC-1(A5)_e.book 17 ページ２００５年１１月１４日　月曜日　午後２時５１分

Description

1. Adaptateur jack CA

Point de connexion de l’adaptateur CA fourni.

2. Borne de mise à la terre

3. Jacks de sortie analogique 1/2 [ANALOG OUTPUT 1/2]

Prises jack de sortie analogique pour vidéo et audio, à brancher sur l’écran de télévision, le

graveur DVD ou le magnétoscope.

4. Prise jack d’entrée analogique [ANALOG INPUT]

Prise jack vidéo/audio analogique. Se branche sur votre magnétoscope VHS ou 8 mm.

* L’entrée S-vidéo est prioritaire lorsque des câbles vidéo sont connectés sur la prise jack d’entrée S-

vidéo et la prise jack d’entrée composite.

5. Connecteur DV 1 [DV1 IN/OUT]

Se branche sur appareil DV ou ordinateur.

* Ne pas utiliser en même temps que le connecteur DV 2 situé sur la face avant du VMC-1 (p. 16). En

cas d’utilisation simultanée, l’appareil DV risque de ne pas fonctionner correctement.

6. Verrouillage ( )

http://www.kensington.com/

Face arrière

VMC-1(A5)_e.book 18 ページ２００５年１１月１４日　月曜日　午後２時５１分

Español Italiano Français Deutsch English

Description

1. Commutateur de réglage du format vidéo [Video Format]

Définit le format du signal vidéo.

2. Commutateur de réglage NTSC [NTSC Setup Level]

Définit le niveau de paramétrage NTSC.

Sélectionner 0IRE au Japon et 7.5IRE en Amérique du Nord.

3. Commutateur de mode audio verrouillé [Locked Audio Mode]

Définit le mode Audio verrouillé pour entrée analogique.

4. Commutateur de réglage du format audio [Audio Format]

Définit la profondeur de bits et la fréquence d’échantillonnage audio pour les entrées analo-

giques.

5. Commutateur de mode Audio mix [Audio Mix Mode]

Détermine si les sous-canaux fonctionneront en sortie lorsqu’un format audio 4 canaux 32

kHz/12 bits est introduit en entrée via DV.

6. Commutateur de réglage silencieux

Selon le logiciel d'édition vidéo utilisé, un bruit audio peut se faire entendre au début de la

lecture si ce commutateur est en position MARCHE (ON). Dans un tel cas, le mettre en

position ARRÊT (OFF).

* Lorsque le VMC-1 est expédié de la fabrique, le commutateur DIP 6 est en position ARRÊT (OFF).

Mettre l’appareil hors tension avant de modifier le réglage des commutateurs DIP sur la

face inférieure.

Face inférieure (commutateurs DIP)

OFF

NTSC

ON PAL

OFF 0IRE

ON 7.5IRE

OFF Locked

ON Unlocked

OFF 48kHz/16bit

ON 32kHz/12bit

OFF Main only

ON Mix 50% main + 50% sub

OFF Normal

ON Court

SER.NO.SER.NO.

MODELMODEL

VMC

1VMC

MADE IN JAPANMADE IN JAPAN

OFF ON

1Video Format NTSC PAL

OFF ON

2 NTSC Setup Level 0 IRE 7.5 IRE

3 Locked Audio Mode LOCKED UNKOCKED

4 Audio Format 48kHz /

16bit 32kHz /

12bit

5 Audio Mix Mode MAIN MAIN

SUB

6 Reserved

OFF ON

VMC-1(A5)_e.book 19 ページ２００５年１１月１４日　月曜日　午後２時５１分

Nomi delle cose e loro funzioni

1. Connettore DV 2 [DV2 IN/OUT]

Connettere il vostro apparecchio Dv o computer qui.

* Non è possibile usarlo contemporaneamente con il connettore DV 1 ed il pannello posteriore del VMC-

1. (p. 22). Se vengono usati contemporaneamente, è possibile che il vostro apparecchio DV non

funzioni correttamente.

2. Pulsante d’ingresso del DV [DV IN]

Accendere se desiderate che i segnali video e audio del vostro apparecchio DV vengano

inviati dall’uscita analogica.

3. Pulsante d’ingresso analogico [ANALOG IN]

Accendere se desiderate che i segnali video e audio dell’ingresso analogico vengano inviati

dall’uscita analogica.

4. Indicatore del sincronizzatore dell’immagine [FRAME SYNC]

Questo indicatore si accende quando viene immesso un segnale video analogico. Il

sincronizzatore dell’immagine corregge tutte le imprecisioni della sincronizzazione causate

da un segnale video instabile, evitando in questo modo la perdita d’immagine e la caduta del

suono.

5. Pulsante del correttore del tempo base [TBC]

Serve a correggere l’instabilità dell’immagine che spesso si verifica quando un apparecchio

video analogico sta riproducendo. Di norma occorre tenere accesa questa funzione. Se viene

accesa, i segnali video e audio verranno emessi con un certo ritardo rispetto al segnale

d’ingresso e ciò per consentire lo svolgimento dell’operazione. Se il ritardo rappresenta un

problema, è possibile spegnere questa funzione.

6. Pulsante di separazione 3-D Y/C [3D Y/C]

È disponibile solo con la modalità NTSC (p. 23). Riduce alcuni problemi che si possono

verificare quando viene emesso un segnale composito, come per esempio sottili linee

diagonali bianche e nere che producono un effetto arcobaleno (colore trasversale) o che

causano l’apparizione di punti bianchi e neri (interferenza di punti) e depura il segnale

Pannello Pa

VMC-1(A5)_e.book 20 ページ２００５年１１月１４日　月曜日　午後２時５１分

La pagina sta caricando ...

Edirol VMC-1 Manuale del proprietario

Marca: Edirol

Modello: VMC-1

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Edirol VMC-1 Owner's manual
español: Edirol VMC-1 El manual del propietario

Edirol VMC-1 Manuale del proprietario

Edirol VMC-1 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti