Roland R-4 Manuale utente

As of January 15, 2005 (EDIROL-1)

Information When you need repair service, call your nearest EDIROL/Roland Service Center or authorized

EDIROL/Roland distributor in your country as shown below.

EUROPE

EDIROL (Europe) Ltd.

Studio 3.4 114 Power Road

London W4 5PY

U. K.

TEL: +44 (0)20 8747 5949

FAX:+44 (0)20 8747 5948

http://www.edirol.com/europe

Deutschland

TEL: 0700 33 47 65 20

France

TEL: 0810 000 371

Italia

TEL: 02 93778329

U. S. A. / CANADA

EDIROL Corporation

North America

425 Sequoia Drive, Suite 114

Bellingham, WA 98226

U. S. A.

TEL: (360) 594-4273

FAX: (360) 594-4271

http://www.edirol.com/

EGYPT

Al Fanny Trading Office

9, EBN Hagar A1 Askalany

Street,

ARD E1 Golf, Heliopolis,

Cairo 11341, EGYPT

TEL: 20-2-417-1828

REUNION

Maison FO - YAM Marcel

25 Rue Jules Hermann,

Chaudron - BP79 97 491

Ste Clotilde Cedex,

REUNION ISLAND

TEL: (0262) 218-429

SOUTH AFRICA

Paul Bothner(PTY)Ltd.

17 Werdmuller Centre,

Main Road, Claremont 7708

SOUTH AFRICA

TEL: (021) 674 4030

CHINA

Roland Shanghai Electronics

Co.,Ltd.

5F. No.1500 Pingliang Road

Shanghai 200090, CHINA

TEL: (021) 5580-0800

Roland Shanghai Electronics

Co.,Ltd.

(BEIJING OFFICE)

10F. No.18 3 Section Anhuaxili

Chaoyang District Beijing

100011 CHINA

TEL: (010) 6426-5050

Roland Shanghai Electronics

Co.,Ltd.

(GUANGZHOU OFFICE)

2/F., No.30 Si You Nan Er Jie

Yi Xiang, Wu Yang Xin Cheng,

Guangzhou 510600, CHINA

TEL: (020) 8736-0428

HONG KONG

Parsons Music Ltd.

8th Floor, Railway Plaza, 39

Chatham Road South, T.S.T,

Kowloon, HONG KONG

TEL: 2333 1863

INDIA

Rivera Digitec (India) Pvt. Ltd.

409, Nirman Kendra

Mahalaxmi Flats Compound

Off. Dr. Edwin Moses Road,

Mumbai-400011, INDIA

TEL: (022) 2493 9051

INDONESIA

PT Citra IntiRama

J1. Cideng Timur No. 15J-150

Jakarta Pusat

INDONESIA

TEL: (021) 6324170

KOREA

Cosmos Corporation

1461-9, Seocho-Dong,

Seocho Ku, Seoul, KOREA

TEL: (02) 3486-8855

MALAYSIA/

SINGAPORE

Roland Asia Pacific Sdn. Bhd.

45-1, Block C2, Jalan PJU 1/39,

Dataran Prima, 47301 Petaling

Jaya, Selangor, MALAYSIA

TEL: (03) 7805-3263

PHILIPPINES

G.A. Yupangco & Co. Inc.

339 Gil J. Puyat Avenue

Makati, Metro Manila 1200,

PHILIPPINES

TEL: (02) 899 9801

TAIWAN

ROLAND TAIWAN

ENTERPRISE CO., LTD.

Room 5, 9fl. No. 112 Chung

Shan N.Road Sec.2, Taipei,

TAIWAN, R.O.C.

TEL: (02) 2561 3339

THAILAND

Theera Music Co. , Ltd.

330 Verng NakornKasem, Soi

2, Bangkok 10100, THAILAND

TEL: (02) 2248821

VIETNAM

Saigon Music

Suite DP-8

40 Ba Huyen Thanh Quan

Street

Hochiminh City, VIETNAM

TEL: (08) 930-1969

AUSTRALIA/

NEW ZEALAND

Roland Corporation

Australia Pty.,Ltd.

38 Campbell Avenue

Dee Why West. NSW 2099

AUSTRALIA

For Australia

Tel: (02) 9982 8266

For New Zealand

Tel: (09) 3098 715

ARGENTINA

Instrumentos Musicales S.A.

Av.Santa Fe 2055

(1123) Buenos Aires

ARGENTINA

TEL: (011) 4508-2700

BARBADOS

A&B Music Supplies LTD

12 Webster Industrial Park

Wildey, St.Michael, Barbados

TEL: (246)430-1100

BRAZIL

Roland Brasil Ltda.

Rua San Jose, 780 Sala B

Parque Industrial San Jose

Cotia - Sao Paulo - SP, BRAZIL

TEL: (011) 4615 5666

CHILE

Comercial Fancy II S.A.

Rut.: 96.919.420-1

Nataniel Cox #739, 4th Floor

Santiago - Centro, CHILE

TEL: (02) 688-9540

COLOMBIA

Centro Musical Ltda.

Cra 43 B No 25 A 41 Bododega 9

Medellin, Colombia

TEL: (574)3812529

CURACAO

Zeelandia Music Center Inc.

Orionweg 30

Curacao, Netherland Antilles

TEL:(305)5926866

DOMINICAN REPUBLIC

Instrumentos Fernando Giraldez

Calle Proyecto Central No.3

Ens.La Esperilla

Santo Domingo,

Dominican Republic

TEL:(809) 683 0305

ECUADOR

Mas Musika

Rumichaca 822 y Zaruma

Guayaquil - Ecuador

TEL:(593-4)2302364

GUATEMALA

Casa Instrumental

Calzada Roosevelt 34-01,zona 11

Ciudad de Guatemala

Guatemala

TEL:(502) 599-2888

HONDURAS

Almacen Pajaro Azul S.A. de C.V.

BO.Paz Barahona

3 Ave.11 Calle S.O

San Pedro Sula, Honduras

TEL: (504) 553-2029

MARTINIQUE

Musique & Son

Z.I.Les Mangle

97232 Le Lamantin

Martinique F.W.I.

TEL: 596 596 426860

Gigamusic SARL

10 Rte De La Folie

97200 Fort De France

Martinique F.W.I.

TEL: 596 596 715222

MEXICO

Casa Veerkamp, s.a. de c.v.

Av. Toluca No. 323, Col. Olivar

de los Padres 01780 Mexico

D.F. MEXICO

TEL: (55) 5668-6699

NICARAGUA

Bansbach Instrumentos

Musicales Nicaragua

Altamira D'Este Calle Principal

de la Farmacia 5ta.Avenida

1 Cuadra al Lago.#503

Managua, Nicaragua

TEL: (505)277-2557

IRELAND

Roland Ireland

G2 Calmount Park, Calmount

Avenue, Dublin 12

Republic of IRELAND

TEL: (01) 4294444

ITALY

Roland Italy S. p. A.

Viale delle Industrie 8,

20020 Arese, Milano, ITALY

TEL: (02) 937-78300

NORWAY

Roland Scandinavia Avd.

Kontor Norge

Lilleakerveien 2 Postboks 95

Lilleaker N-0216 Oslo

NORWAY

TEL: 2273 0074

POLAND

MX MUSIC SP.Z.O.O.

UL. Gibraltarska 4.

PL-03664 Warszawa POLAND

TEL: (022) 679 44 19

PORTUGAL

Roland Iberia, S.L.

Portugal Office

Cais das Pedras, 8/9-1 Dto

4050-465, Porto, PORTUGAL

TEL: 22 608 00 60

ROMANIA

FBS LINES

Piata Libertatii 1,

535500 Gheorgheni,

ROMANIA

TEL: (266) 364 609

RUSSIA

MuTek

3-Bogatyrskaya Str. 1.k.l

107 564 Moscow, RUSSIA

TEL: (095) 169 5043

SPAIN

Roland Iberia, S.L.

Paseo García Faria, 33-35

08005 Barcelona SPAIN

TEL: 93 493 91 00

SWEDEN

Roland Scandinavia A/S

SWEDISH SALES OFFICE

Danvik Center 28, 2 tr.

S-131 30 Nacka SWEDEN

TEL: (0)8 702 00 20

SWITZERLAND

Roland (Switzerland) AG

Landstrasse 5, Postfach,

CH-4452 Itingen,

SWITZERLAND

TEL: (061) 927-8383

UKRAINE

TIC-TAC

Mira Str. 19/108

P.O. Box 180

295400 Munkachevo,

UKRAINE

TEL: (03131) 414-40

UNITED KINGDOM

Roland (U.K.) Ltd.

Atlantic Close, Swansea

Enterprise Park, SWANSEA

SA7 9FJ,

UNITED KINGDOM

TEL: (01792) 702701

BAHRAIN

Moon Stores

No.16, Bab Al Bahrain Avenue,

P.O.Box 247, Manama 304,

State of BAHRAIN

TEL: 17 211 005

PERU

Audionet

Distribuciones Musicales SAC

Juan Fanning 530

Miraflores

Lima - Peru

TEL: (511) 4461388

TRINIDAD

AMR Ltd

Ground Floor

Maritime Plaza

Barataria Trinidad W.I.

TEL: (868)638 6385

URUGUAY

Todo Musica S.A.

Francisco Acuna de Figueroa 1771

C.P.: 11.800

Montevideo, URUGUAY

TEL: (02) 924-2335

VENEZUELA

Instrumentos Musicales

Allegro,C.A.

Av.las industrias edf.Guitar

import

#7 zona Industrial de Turumo

Caracas, Venezuela

TEL: (212) 244-1122

AUSTRIA

Roland Elektronische

Musikinstrumente HmbH.

Austrian Office

Eduard-Bodem-Gasse 8,

A-6020 Innsbruck, AUSTRIA

TEL: (0512) 26 44 260

BELGIUM/FRANCE/

HOLLAND/

LUXEMBOURG

Roland Central Europe N.V.

Houtstraat 3, B-2260, Oevel

(Westerlo) BELGIUM

TEL: (014) 575811

CZECH REP.

K-AUDIO

Kardasovska 626.

CZ-198 00 Praha 9,

CZECH REP.

TEL: (2) 666 10529

DENMARK

Roland Scandinavia A/S

Nordhavnsvej 7, Postbox 880,

DK-2100 Copenhagen

DENMARK

TEL: 3916 6200

FINLAND

Roland Scandinavia As, Filial

Finland

Elannontie 5

FIN-01510 Vantaa, FINLAND

TEL: (0)9 68 24 020

GERMANY

Roland Elektronische

Musikinstrumente HmbH.

Oststrasse 96, 22844

Norderstedt, GERMANY

TEL: (040) 52 60090

GREECE

STOLLAS S.A.

Music Sound Light

155, New National Road

Patras 26442, GREECE

TEL: 2610 435400

HUNGARY

Roland East Europe Ltd.

Warehouse Area ‘DEPO’ Pf.83

H-2046 Torokbalint,

HUNGARY

TEL: (23) 511011

CYPRUS

Radex Sound Equipment Ltd.

17, Diagorou Street, Nicosia,

CYPRUS

TEL: (022) 66-9426

IRAN

MOCO INC.

No.41 Nike St., Dr.Shariyati Ave.,

Roberoye Cerahe Mirdamad

Tehran, IRAN

TEL: (021) 285-4169

ISRAEL

Halilit P. Greenspoon & Sons

Ltd.

8 Retzif Ha’aliya Hashnya St.

Tel-Aviv-Yafo ISRAEL

TEL: (03) 6823666

JORDAN

AMMAN Trading Agency

245 Prince Mohammad St.,

Amman 1118, JORDAN

TEL: (06) 464-1200

KUWAIT

EASA HUSAIN AL-YOUSIFI

& SONS CO.

Abdullah Salem Street,

Safat, KUWAIT

TEL: 243-6399

LEBANON

Chahine S.A.L.

Gerge Zeidan St., Chahine

Bldg., Achrafieh, P.O.Box: 16-

5857

Beirut, LEBANON

TEL: (01) 20-1441

OMAN

TALENTZ CENTRE L.L.C.

P.O. BOX 37, MUSCAT,

POSTAL CODE 113

TEL: 931-3705

QATAR

Badie Studio & Stores

P.O. Box 62,

Doha, QATAR

TEL: 423554

SAUDI ARABIA

aDawliah Universal

Electronics APL

Corniche Road, Aldossary

Bldg., 1st Floor, Alkhobar,

SAUDI ARABIA

P.O.Box 2154, Alkhobar 31952

SAUDI ARABIA

TEL: (03) 898 2081

SYRIA

Technical Light & Sound

Center

Rawda, Abdul Qader Jazairi St.

Bldg. No. 21, P.O.BOX 13520,

Damascus, SYRIA

TEL: (011) 223-5384

TURKEY

Ant Muzik aletleri ithalat ve

ihracat Ltd Sti

Siraselviler Caddesi

Siraselviler Pasaji No:74/20

Taksim - Istanbul, TURKEY

TEL: (0212) 2449624

U.A.E.

Zak Electronics & Musical

Instruments Co. L.L.C.

Zabeel Road, Al Sherooq Bldg.,

No. 14, Grand Floor, Dubai,

U.A.E.

TEL: (04) 3360715

ASIA

AFRICA

AUSTRALIA/

NEW ZEALAND

EUROPE

CENTRAL/LATIN

AMERICA

MIDDLE EAST

201a

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT

NOTES” (p. 3– p. 6). These sections provide important information concerning the proper operation of the unit.

Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new

unit, Owner’s Manual should be read in its entirety. The manual should be saved and kept on hand as a

convenient reference.

without the written permission of ROLAND CORPORATION.

03783701 ’05-2-1N

Owner’s Manual

To resize thickness, move all items on the front cover

and center registration marks to left or right.

To resize thickness, move all items on the front cover

For the USA

DECLARATION OF CONFORMITY

Compliance Information Statement

Model Name :

Type of Equipment :

Responsible Party :

Address :

Telephone :

R-4

4-CHANNEL PORTABLE RECORDER and WAVE EDITOR

Edirol Corporation North America

425 Sequoia Drive, Suite 114, Bellingham, WA 98226

(360) 594-4276

This product complies with the requirements of European Directive 89/336/EEC.

For EU Countries

Apparatus containing

Lithium batteries

ADVARSEL!

Lithiumbatteri - Eksplosionsfare ved

fejlagtig håndtering.

Udskiftning må kun ske med batteri af

samme fabrikat og type.

Levér det brugte batteri tilbage til

leverandøren.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en

ekvivalent typ som rekommenderas av

apparattillverkaren.

Kassera använt batteri enligt

fabrikantens instruktion.

CAUTION

Danger of explosion if battery is

incorrectly replaced.

Replace only with the same or

equivalent type recommended by the

manufacturer.

Discard used batteries according to the

manufacturer’s instructions.

ADVARSEL

Eksplosjonsfare ved feilaktig skifte av

batteri.

Benytt samme batteritype eller en

tilsvarende type anbefalt av

apparatfabrikanten.

Brukte batterier kasseres i henhold til

fabrikantens instruks joner.

VAROITUS

Paristo voi räjähtää, jos se on

virheellisesti asennettu.

Vaihda paristo ainoastaan

laitevalmistajan suosittelemaan

tyyppiin. Hävitä käytetty paristo

valmistajan ohjeiden mukaisesti.

For Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

NOTICE

AVIS

For the USA

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modification to this system can void the users authority to operate this equipment.

This equipment requires shielded interface cables in order to meet FCC class B Limit.

and center registration marks to left or right.

IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.

BLUE:

BROWN:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.

NEUTRAL

LIVE

For the U.K.

204

* Microsoft and Windows are registered trademarks of Microsoft Corporation.

206j

* Windows

®

is known officially as: “Microsoft

®

Windows

®

operating system.”

207

* Apple and Macintosh are registered trademarks of Apple Computer, Inc.

209

* Mac OS is a trademark of Apple Computer, Inc.

220

* All product names mentioned in this document are trademarks or registered trademarks of their respective owners.

234

* CompactFlash and are trademarks of SanDisk Corporation and licensed by CompactFlash association.

235

* Roland Corporation is an authorized licensee of the CompactFlash

™

and CF logo ( ) trademarks.

236

fig.Fugue-logo.eps

3

USING THE UNIT SAFELY

001

• Before using this unit, make sure to read the

instructions below, and the Owner’s Manual.

................................................................................................

002c

• Do not open (or modify in any way) the unit or its

AC adaptor.

................................................................................................

003

• Do not attempt to repair the unit, or replace parts

within it (except when this manual provides

specific instructions directing you to do so). Refer

all servicing to your retailer, the nearest Roland Service

Center, or an authorized Roland distributor, as listed on

the “Information” page.

................................................................................................

004

• Never use or store the unit in places that are:

• Subject to temperature extremes (e.g., direct

sunlight in an enclosed vehicle, near a heating

duct, on top of heat-generating equipment); or

are

• Damp (e.g., baths, washrooms, on wet floors); or are

• Humid; or are

• Exposed to rain; or are

• Dusty; or are

• Subject to high levels of vibration.

................................................................................................

007

• Make sure you always have the unit placed so it is

level and sure to remain stable. Never place it on

stands that could wobble, or on inclined surfaces.

................................................................................................

008c

• Be sure to use only the AC adaptor supplied with

the unit. Also, make sure the line voltage at the

installation matches the input voltage specified on

the AC adaptor’s body. Other AC adaptors may use a

different polarity, or be designed for a different voltage, so

their use could result in damage, malfunction, or electric

shock.

................................................................................................

008e

• Use only the attached power-supply cord. Also,

the supplied power cord must not be used with

any other device.

................................................................................................

009

• Do not excessively twist or bend the power cord,

nor place heavy objects on it. Doing so can damage

the cord, producing severed elements and short

circuits. Damaged cords are fire and shock hazards!

................................................................................................

010

• This unit, either alone or in combination with an

amplifier and headphones or speakers, may be

capable of producing sound levels that could cause

permanent hearing loss. Do not operate for a long period

of time at a high volume level, or at a level that is uncom-

fortable. If you experience any hearing loss or ringing in

the ears, you should immediately stop using the unit, and

consult an audiologist.

................................................................................................

011

• Do not allow any objects (e.g., flammable material,

coins, pins); or liquids of any kind (water, soft

drinks, etc.) to penetrate the unit.

................................................................................................

012b

• Immediately turn the power off, remove the AC

adaptor from the outlet, and request servicing by

your retailer, the nearest Roland Service Center, or an

authorized Roland distributor, as listed on the “Infor-

mation” page when:

• The AC adaptor, the power-supply cord, or the plug has been

damaged; or

• If smoke or unusual odor occurs

• Objects have fallen into, or liquid has been spilled onto the unit;

or

• The unit has been exposed to rain (or otherwise has become

wet); or

• The unit does not appear to operate normally or exhibits a

marked change in performance.

................................................................................................

Used for instructions intended to alert

the user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic

animals or pets.

Used for instructions intended to alert

the user to the risk of death or severe

injury should the unit be used

improperly.

The ● symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In

the case of the symbol at left, it means that the power-

cord plug must be unplugged from the outlet.

The symbol alerts the user to important instructions

or warnings.The specific meaning of the symbol is

determined by the design contained within the

triangle. In the case of the symbol at left, it is used for

general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never

be carried out (are forbidden). The specific thing that

must not be done is indicated by the design contained

within the circle. In the case of the symbol at left, it

means that the unit must never be disassembled.

R-4_e.book 3 ページ２００５年２月１０日　木曜日　午後３時３６分

4

013

• In households with small children, an adult should

provide supervision until the child is capable of

following all the rules essential for the safe operation of

the unit.

................................................................................................

014

• Protect the unit from strong impact.

(Do not drop it!)

................................................................................................

015

• Do not force the unit’s power-supply cord to share

an outlet with an unreasonable number of other

devices. Be especially careful when using extension

cords—the total power used by all devices you have

connected to the extension cord’s outlet must never

exceed the power rating (watts/amperes) for the

extension cord. Excessive loads can cause the insulation

on the cord to heat up and eventually melt through.

................................................................................................

016

• Before using the unit in a foreign country, consult

with your retailer, the nearest Roland Service

Center, or an authorized Roland distributor, as listed on

the “Information” page.

................................................................................................

019

• Batteries must never be recharged, heated, taken

apart, or thrown into fire or water.

................................................................................................

101b

• The unit and the AC adaptor should be located so

their location or position does not interfere with

their proper ventilation.

................................................................................................

102c

• Always grasp only the plug on the AC adaptor

cord when plugging into, or unplugging from, an

outlet or this unit.

................................................................................................

103b

• At regular intervals, you should unplug the AC

adaptor and clean it by using a dry cloth to wipe

all dust and other accumulations away from its

prongs. Also, disconnect the power plug from the power

outlet whenever the unit is to remain unused for an

extended period of time. Any accumulation of dust

between the power plug and the power outlet can result in

poor insulation and lead to fire.

................................................................................................

104

• Try to prevent cords and cables from becoming

entangled. Also, all cords and cables should be

placed so they are out of the reach of children.

................................................................................................

106

• Never climb on top of, nor place heavy objects on

the unit.

................................................................................................

107c

• Never handle the AC adaptor or its plugs with wet

hands when plugging into, or unplugging from, an

outlet or this unit.

................................................................................................

108b

• Before moving the unit, disconnect the AC adaptor

and all cords coming from external devices.

................................................................................................

109b

• Before cleaning the unit, turn off the power and

unplug the AC adaptor from the outlet.

................................................................................................

110b

• Whenever you suspect the possibility of lightning

in your area, disconnect the AC adaptor from the

outlet.

................................................................................................

111: Selection

• If used improperly, batteries may explode or leak

and cause damage or injury. In the interest of

safety, please read and observe the following

precautions (p. 25).

1

• Carefully follow the installation instructions for

batteries, and make sure you observe the correct

polarity.

2

• Avoid using new batteries together with used ones. In

addition, avoid mixing different types of batteries.

3

• Remove the batteries whenever the unit is to remain

unused for an extended period of time.

5

• If a battery has leaked, use a soft piece of cloth or paper

towel to wipe all remnants of the discharge from the

battery compartment. Then install new batteries. To

avoid inflammation of the skin, make sure that none of

the battery discharge gets onto your hands or skin.

Exercise the utmost caution so that none of the

discharge gets near your eyes. Immediately rinse the

affected area with running water if any of the discharge

has entered the eyes.

6

• Never keep batteries together with metallic objects such

as ballpoint pens, necklaces, hairpins, etc.

................................................................................................

112

• Used batteries must be disposed of in compliance

with whatever regulations for their safe disposal

that may be observed in the region in which you

live.

................................................................................................

118a

• Should you remove the ground terminal screw,

keep them in a safe place out of children’s reach, so

there is no chance of them being swallowed

accidentally.

................................................................................................

120

• Always turn the phantom power off when

connecting any device other than condenser micro-

phones that require phantom power. You risk causing

damage if you mistakenly supply phantom power to

dynamic microphones, audio playback devices, or other

devices that don’t require such power. Be sure to check

the specifications of any microphone you intend to use by

referring to the manual that came with it.

This instrument’s phantom power: 48V DC, 8 mA Max

(total of all channels must be 25 mA or less)

................................................................................................

R-4_e.book 4 ページ２００５年２月１０日　木曜日　午後３時３６分

5

Important Notes

291a

In addition to the items listed under “USING THE UNIT SAFELY” on page 3, please read and observe the following:

Power Supply: Use of Batteries

301

• Do not connect this unit to same electrical outlet that is

being used by an electrical appliance that is controlled by

an inverter (such as a refrigerator, washing machine,

microwave oven, or air conditioner), or that contains a

motor. Depending on the way in which the electrical

appliance is used, power supply noise may cause this unit

to malfunction or may produce audible noise. If it is not

practical to use a separate electrical outlet, connect a power

supply noise filter between this unit and the electrical

outlet.

302

• The AC adaptor will begin to generate heat after long

hours of consecutive use. This is normal, and is not a cause

for concern.

303a

• The use of an AC adaptor is recommended as the unit’s

power consumption is relatively high. Should you prefer to

use batteries, please use the alkaline or nickel metal

hydride type.

304a

• When installing or replacing batteries, always turn off the

power on this unit and disconnect any other devices you

may have connected. This way, you can prevent

malfunction and/or damage to speakers or other devices.

307

• Before connecting this unit to other devices, turn off the

power to all units. This will help prevent malfunctions

and/or damage to speakers or other devices.

Placement

351

• Using the unit near power amplifiers (or other equipment

containing large power transformers) may induce hum. To

alleviate the problem, change the orientation of this unit; or

move it farther away from the source of interference.

352a

• This device may interfere with radio and television

reception. Do not use this device in the vicinity of such

receivers.

352b

• Noise may be produced if wireless communications

devices, such as cell phones, are operated in the vicinity of

this unit. Such noise could occur when receiving or initi-

ating a call, or while conversing. Should you experience

such problems, you should relocate such wireless devices

so they are at a greater distance from this unit, or switch

them off.

354a

• Do not expose the unit to direct sunlight, place it near

devices that radiate heat, leave it inside an enclosed

vehicle, or otherwise subject it to temperature extremes.

Excessive heat can deform or discolor the unit.

355b

• When moved from one location to another where the

temperature and/or humidity is very different, water

droplets (condensation) may form inside the unit. Damage

or malfunction may result if you attempt to use the unit in

this condition. Therefore, before using the unit, you must

allow it to stand for several hours, until the condensation

has completely evaporated.

Maintenance

401a

• For everyday cleaning wipe the unit with a soft, dry cloth

or one that has been slightly dampened with water. To

remove stubborn dirt, use a cloth impregnated with a mild,

non-abrasive detergent. Afterwards, be sure to wipe the

unit thoroughly with a soft, dry cloth.

402

• Never use benzine, thinners, alcohol or solvents of any

kind, to avoid the possibility of discoloration and/or defor-

mation.

Repairs and Data

452

• Please be aware that all data contained in the unit’s

memory may be lost when the unit is sent for repairs.

Important data should always be backed up on a

CompactFrash, your computer, or written down on paper

(when possible). During repairs, due care is taken to avoid

the loss of data. However, in certain cases (such as when

circuitry related to memory itself is out of order), we regret

that it may not be possible to restore the data, and Roland

assumes no liability concerning such loss of data.

Memory Backup

501b

• The R-4 contains a battery that keeps the internal clock

running even when the power is turned off. When this

battery runs low, the message shown below will appear in

the display. Replace the battery as soon as possible, since

the clock will not keep the correct time if the battery is low.

To have the battery replaced, consult with your retailer, the

nearest Roland Service Center, or an authorized Roland

distributor, as listed on the “Information” page.

Int-Batt Low!

Additional Precautions

551

• Please be aware that the contents of memory can be

irretrievably lost as a result of a malfunction, or the

improper operation of the unit. To protect yourself against

the risk of loosing important data, we recommend that you

periodically save a backup copy of important data you

have stored in the unit’s memory on a CompactFrash or

your computer.

552

• Unfortunately, it may be impossible to restore the contents

of data that was stored on a hard disk, or a CompactFrash

once it has been lost. Roland Corporation assumes no

liability concerning such loss of data.

553

• Use a reasonable amount of care when using the unit’s

buttons, sliders, or other controls; and when using its jacks

and connectors. Rough handling can lead to malfunctions.

554

• Never strike or apply strong pressure to the display.

556

• When connecting / disconnecting all cables, grasp the

connector itself—never pull on the cable. This way you will

avoid causing shorts, or damage to the cable’s internal

elements.

R-4_e.book 5 ページ２００５年２月１０日　木曜日　午後３時３６分

6

Important Notes

558a

• To avoid disturbing your neighbors, try to keep the unit’s

volume at reasonable levels. You may prefer to use

headphones, so you do not need to be concerned about

those around you (especially when it is late at night).

559a

• When you need to transport the unit, package it in the box

(including padding) that it came in, if possible. Otherwise,

you will need to use equivalent packaging materials.

562

• Use a cable from Roland to make the connection. If using

some other make of connection cable, please note the

following precautions.

• Some connection cables contain resistors. Do not use

cables that incorporate resistors for connecting to this

unit. The use of such cables can cause the sound level to

be extremely low, or impossible to hear. For infor-

mation on cable specifications, contact the manufac-

turer of the cable.

Before Using Cards

704

• Carefully insert the DATA card all the way in—until it is

firmly in place.

fig.M512-Insert

705

• Never touch the terminals of the DATA card. Also, avoid

getting the terminals dirty.

707

• This unit’s memory card slot accepts CompactFlash

memory cards. Microdrive storage media are not

compatible.

Handling Hard Disks

811

• Once a hard disk fails to function normally, all data that

has been stored on it could be destroyed.

All hard disks eventually wear out.

We recommend that

you consider the hard disk not as a permanent storage site,

but as a place to store data temporarily. We also

recommend that you back up important performance and

image data that cannot be recorded again onto the external

media that is supported by your device. For instructions on

how to make such backups, refer to the owner’s manual for

your device.

Note that Roland assumes no liability whatsoever,

including monetary compensation, for the loss of any

recorded content in the event of the malfunction of, or

physical damage to the hard disk, or for any direct or

incidental damages resulting from the loss of such data.

Precautions Regarding Setup and Use

812

• Certain hard disk setup procedures and usage conditions

may result in the corruption of recorded data, malfunc-

tioning, or physical damage to the disk, so be sure to

observe the following precautions.

• Do not subject the hard disk to vibration or shock,

especially while the unit is in operation.

• Do not set up the unit in any location where it may be

affected by vibration from external sources, or on any

surface that is not stable and level.

• If the device includes a cooling fan, ensure that the fan

and the side panel air vents remain unobstructed.

• Do not leave the unit in any environment subject to

temperature extremes; for example, in a closed

automobile in summer or outdoors during winter.

• Do not use the unit in conditions of high temperature

and humidity or in any location subject to rapid

temperature changes.

• Do not unplug the power cord or switch off any circuit

breakers in the circuit to which the unit is connected

while the power is turned on.

Emergency Procedures

813

* The following procedures are to be used as emergency mea-

sures only, and are not recommended for normal operation.

• If the device fails to respond to operational commands or

does not complete operations, turn off the power. If the

power does not shut off following normal shutdown proce-

dures, disconnect the power plug.

If the unit does not operate normally when the power is

turned on again, it may mean that the hard disk has been

damaged. In such instances, consult your dealer or the

nearest Roland Service Center. Note, however, that it may

not be possible to recover any data from the hard disk once

it has been lost.

Copyright

851

• Unauthorized recording, distribution, sale, lending, public

performance, broadcasting, or the like, in whole or in part,

of a work (musical composition, video, broadcast, public

performance, or the like) whose copyright is held by a third

party is prohibited by law.

852b

• When exchanging audio signals through a digital

connection with an external instrument, this unit can

perform recording without being subjected to some of the

restrictions of the Serial Copy Management System

(SCMS). This is because the unit is intended solely for

musical production, and is designed not to be subject to

restrictions as long as it is used to record works (such as

your own compositions) that do not infringe on the

copyrights of others. (SCMS is a feature that prohibits

second-generation and later copying through a digital

connection. It is built into MD recorders and other

consumer digital-audio equipment as a copyright-

protection feature.)

853

• Do not use this unit for purposes that could infringe on a

copyright held by a third party. We assume no responsi-

bility whatsoever with regard to any infringements of

third-party copyrights arising through your use of this

unit.

CompactFlash™

R-4_e.book 6 ページ２００５年２月１０日　木曜日　午後３時３６分

7

Contents

Checking the included items ...... 8

Introducing the R-4 ................... 9

The R-4’s controls and connectors.................9

Display.............................................................18

What is a project? ...........................................21

Getting ready to use the R-4 ... 23

Basic connection examples ...........................23

Connecting the AC adaptor and turning

the power on...................................................24

Installing batteries and turning

the power on...................................................25

Recording ............................... 27

Recording from a connected mic .................27

Recording from the internal mics ................30

Recording digital audio from a digital device

..........................................................................31

Recording analog audio ................................32

Playing back........................... 34

Connections before playback .......................34

Settings before playback ...............................36

Playing back....................................................38

The Finder screen .................... 41

Selecting a project (Select).............................41

Deleting a project (Delete) ............................42

Renaming a project (Rename) ......................43

Copying a project (Copy)..............................44

Moving a project (Move)...............................45

Creating a new folder (Make Folder)..........46

Editing .................................... 48

Editing procedure ..........................................48

Effects setting.......................... 55

Effects...............................................................56

Using effects....................................................58

System settings ....................... 60

System Menu ..................................................60

Example operations .......................................65

Appendix................................ 70

Handling memory cards...............................70

Connection to a computer.............................72

Connecting a video device

that has a LANC connector ..........................74

Application guide ....................75

Connecting an external mic

for CD-quality stereo recording ...................75

Recording birdsongs outdoors.....................76

Recording audio while shooting video.......77

Recording audio memos using just the R-477

Simultaneously recording

environmental sounds (ambience)...............78

Simultaneously recording

at different input levels .................................78

Messages ................................79

Troubleshooting.......................80

Computer-related problems .........................80

Recording-related problems .........................80

Playback-related problems ...........................82

Problems with the R-4’s operation...............83

Main specifications ..................84

Block diagram.........................86

Deutsch.........................................................

Beschreibung des R-4 ..............88

Français ........................................................

Présentation du R-4.................94

Italiano..........................................................

Presentazione dell’R-4...........100

Español .........................................................

Presentación del R-4..............106

Index ....................................112

R-4_e.book 7 ページ２００５年２月１０日　木曜日　午後３時３６分

8

Checking the included items

The R-4 comes with the following items. Immediately after opening the package, please check that you have

all of these items. If any items are missing, please contact the dealer where you purchased the R-4.

■

R-4

fig.R-4.eps_50

■

AC adaptor

This AC adaptor is designed specifically for the R-4. Do not attempt to use any other adaptor with the R-4.

“Connecting the AC adaptor and turning the power on”

(p. 24)

■

USB cable (1 meter)

You can use this cable to connect the R-4 to the USB connector of your computer.

“Connection to a computer”

(p. 72)

* If the AC adaptor or USB cable becomes damaged or if you need a replacement for any reason, please contact one of

the Service Centers listed in the “Information” section at the end of this manual.

* Don't remove the ferrite core that's attached to the USB cable.

■

Carrying case

You can use this case to protect the R-4 while it is being transported or stored.

■

Owner’s manual

This is the document you’re reading. Keep it at hand for easy reference.

R-4_e.book 8 ページ２００５年２月１０日　木曜日　午後３時３６分

9

Introducing the R-4

fig.panel-1.eps_50

Internal mics [MIC-L, MIC-R]

These are stereo mics built into the R-4. The audio entering MIC-L is recorded on the 1L channel, while

audio picked up by MIC-R is recorded on the 1R channel. If you’re recording via the internal mics, set the

System Settings menu item

Recording Setup

to

Int-Mic

. For details, refer to

“Recording from the internal

mics”

(p. 30).

* Don’t connect anything to input jacks you’re not using.

Internal speakers

These are built-in speakers for monitoring. If you want sound to be heard from the internal speakers, set

the System Settings menu item

Speaker

to

ON

. For details, refer to

“Playing back”

(p. 34).

* No sound will be heard from the internal speakers if you’ve connected headphones to the

Headphone jack

( ).

Nor will sound be heard from the internal speakers while recording or in recording-standby mode; this prevents

acoustic feedback from occurring.

Power switch [POWER]

This turns the power on/off. To turn the power on or off, press and hold the power switch for about two

seconds. The power switch is lit green when the power is on.

Don’t turn the power off during recording or playback. Before you turn off the power, you must make sure

that recording or playback is stopped.

* If you accidentally turn off the power during recording, the data that was being recorded will not be stored on the

hard disk.

* The hard disk may be damaged if you turn off the power of the R-4 while data is being read from or written to the

hard disk (such as during recording or playback). You must also be careful not to turn off the power while data is

being transferred between the hard disk and the CompactFlash card.

* Never turn off the power while the R-4’s display indicates Now Connecting... or Now Processing! Doing so will

cause the R-4 to become unstable, and could even damage the internal hard disk.

The R-4’s controls and connectors

Top panel

1

2

3 4 5 6

7 8 9

10

2

1

13

11

12

14 15

16

17

1

2

37

3

R-4_e.book 9 ページ２００５年２月１０日　木曜日　午後３時３６分

10

Introducing the R-4

fig.panel-1.eps_50

Hold switch [HOLD]

By selecting the

HOLD ON

position, you can disable the panel buttons so that unwanted operations will not

occur if a button is pressed accidentally.

However, even if this switch is set to HOLD ON, the

phantom power switches

,

limiter switch ,

input level select switches

,

Input level knobs

, and

Monitor level knob

will still be

operable.

Phantom power switches [PHANTOM POWER]

These switch the phantom power on/off for the XLR type connectors of the combo input jacks located on

the right panel. Since separate switches are provided for channels 1/2 and channels 3/4, you can turn

phantom power on/off separately for these channels.

fig.jack-type

* Always turn the phantom power off when connecting any device other than

condenser microphones that require phantom power. You risk causing damage

if you mistakenly supply phantom power to dynamic microphones, audio

playback devices, or other devices that don’t require such power. Be sure to

check the specifications of any microphone you intend to use by referring to

the manual that came with it.

This instrument’s phantom power: 48 V DC, 8 mA Max

(total of all channels must be 25 mA or less)

Limiter switch [LIMITER]

This is an on/off switch for an input level limiter in the analog circuitry.

When the input level is too high, the limiter compresses the input level appropriately to prevent distortion.

The limiter switch turns limiting on/off for all channels 1–4 together. However, the input level is detected

separately for each channel. You cannot turn the limiter on/off separately for each channel.

1

2

3 4 5 6

7 8 9

10

2

1

13

11

12

14 15

16

17

4

5

6

38

25

26

5

XLR plug

TRS phone

plug

(balanced)

Phone plug

(unbalanced)

6

R-4_e.book 10 ページ２００５年２月１０日　木曜日　午後３時３６分

11

Introducing the R-4

Wave edit button [WAVE EDIT]

This button takes you to Wave Edit mode, where you can edit the waveform using operations such as Trim,

Divide, Combine, and Merge. For details, refer to

“Editing”

(p. 48).

You won't be able to enter Wave Edit mode during playback or recording, or if the R-4’s hard disk contains

no files that the R-4 can handle.

WAV files are the only type of files that the R-4 can handle.

Effect button [EFFECTS]

This button takes you to Effect mode, where you can make effect settings.

For details, refer to

“Effects setting”

(p. 55).

System button [SYSTEM]

This button takes you to a mode where you can make various settings for the R-4.

For details, refer to

“System settings”

(p. 60).

Marker [MARKER]

Clear button [CLEAR]

This button deletes a marker you assigned using the

Mark button

. Markers will be deleted successively,

starting at the marker located immediately before the current location.

button

This button moves you to the marker that is immediately before the current location (the previous marker).

button

This button moves you to the marker that is immediately after the current location (the next marker).

Mark button [MARK]

By pressing this button you can assign a marker to a desired location in the project file. Markers are

numbered sequentially starting at the beginning of the project.

A-B Repeat button [A-B REPEAT]

This button lets you repeatedly play back the region between two points (A and B) in the project. Simply

assign marker A and marker B while the project is playing, and playback will repeat between markers A

and B.

fig.repeat-a

1.

During playback, press the

A-B Repeat button

once.

That point becomes the beginning (marker A) of repeat playback.

fig.repeat-b

2.

Press the

A-B Repeat button

once again. That point will be the end

(marker B) of repeat playback.

fig.repeat-ab

The region you specified in steps 1 and 2 will play repeatedly. To cancel repeat

playback, press the

A-B Repeat button

once again.

Display button [DISPLAY]

This button switches the contents of the R-4’s display.

For details, refer to

“Display”

(p. 18).

7

8

9

10

11

A

AB

12

R-4_e.book 11 ページ２００５年２月１０日　木曜日　午後３時３６分

12

Introducing the R-4

fig.panel-1.eps_50

Cursor/Monitor Select buttons [CURSOR/MONITOR SELECT]

Use these buttons to select items shown in the display. When you’re in the main screen, you can press the

up/down buttons to select the channel that you want to monitor.

For details, refer to

“Display”

(p. 18).

Exit button [EXIT]

Use this button to return to the previous screen or to cancel an operation.

Enter/Finder button [ENTER/FINDER]

Use this button to confirm a setting or finalize a value. You can also press this when you want to use the

Finder function. For more about the Finder function, refer to

“The Finder screen”

(p. 41).

Scrub dial [SCRUB/VALUE]

Use this dial to select among items for which settings are made, or to modify a value. While stopped or

when playback is paused, you can turn the scrub dial to move the current location forward or backward.

Shuttle dial [SHUTTLE]

While the project is playing, turn this dial clockwise to play rapidly forward, or counterclockwise to play

rapidly backward. When the project is stopped, this dial advances the time counter.

1

2

3 4 5 6

7 8 9

10

2

1

13

11

12

14 15

16

17

13

14

15

16

17

R-4_e.book 12 ページ２００５年２月１０日　木曜日　午後３時３６分

13

Introducing the R-4

fig.panel-2.eps_50

Display

This shows various information about the R-4’s status.

For details, refer to

“Display”

(p. 18).

PREV button [PREV]

Pressing the

PREV button

while a project is playing or stopped will take you to the beginning of the project

(00:00:00). Pressing this button at the beginning of a project will take you to the preceding project.

You can also press and hold down this button to rewind. This is available both while playing and while

stopped.

* If the system setting

Player Setup

parameter

Play Mode

is set to

Single

, you can't move to the previous or next

project during playback.

NEXT button [NEXT]

Pressing the

NEXT button

will take you to the next project. You can also press and hold this button to fast-

forward. This is available both while playing and while stopped.

* If the system setting

Player Setup

parameter

Play Mode

is set to

Single

, you can't move to the previous or next

project during playback.

Stop button [STOP]

This button stops playback or recording. If you press the

STOP button

during playback, the counter will

maintain the time at which you pressed the

STOP button

.

Pause button [PAUSE]

This button pauses playback or recording.

Play button [PLAY]

This button starts playback. The

PLAY button

is lit blue during playback.

During playback, you can press the

PLAY button

once again to play at double-speed. During double-

speed playback, press the

PLAY button

once again to return to normal playback. During double-speed

playback, the lower part of the display will indicate

PLAY X2

. Double-speed playback will change the

pitch.

* If you want to turn off the double-speed playback feature, go to the System Settings menu and in

Player Setup

,

turn

X2 Play OFF

. For details, refer to

“2 Player Setup”

(p. 62).

Record button [REC]

Recording will begin immediately when you press the

REC button

. The

REC button

is lit red during

recording. If you hold down the

PAUSE button

and press the

REC button

, the

REC button

will blink

red, and the R-4 enters recording-standby mode. Recording will begin when you then press the

REC

button

or

PAUSE button

.

Input level knobs 1–4 [INPUT GAIN]

These knobs adjust the input level of

combo input jacks 1–4

( ). Input levels of the

internal mics

( ) are adjusted by

knob 1

(MIC-L) and

knob 2

(MIC-R).

Monitor level knob [MONITOR]

This adjusts the output volume of the

internal speakers

( ) and the

headphone jack

().

You can’t adjust the volume of the

line output jacks

( ). If you need to adjust the volume of the line

output jacks, adjust the controls of the external speakers or playback system connected to the line output

jacks.

Front panel

18

19

20

21

22

23

25

26

24

18

19

20

21

22

23

24

22

25

39

1

26

2

37

40

R-4_e.book 13 ページ２００５年２月１０日　木曜日　午後３時３６分

14

Introducing the R-4

Digital input connector [DIGITAL IN]

If you want to record a digital signal, connect a coaxial-type cable to this connector. The digital input signal

is recorded in stereo on channels 1L and 1R. If you want to record in monaural, you’ll need to change the

Rec Mode

setting in the System Settings menu. For details, refer to

“1 Recording Setup”

(p. 60).

Digital output connector [DIGITAL OUT]

This connector outputs a digital signal. You can use a coaxial-type cable to connect this to a digital

recording device such as a DAT or MD recorder. This connector provides the same audio signal as the

line

output jacks

( ) and

headphone jack

( ), but in digital form.

L connector [L-CONNECTOR]

You can use a stereo mini-mini-plug LANC cable to connect this to a video device that is equipped with a

LANC connector. When you begin recording on your video device, the R-4 will begin recording in tandem.

When you stop recording on your video device, the R-4 will also stop recording.

For details, refer to

“Connecting a video device that has a LANC connector”

(p. 74).

USB connector [USB]

Use the included USB cable to connect this to your computer. Projects recorded on the R-4 can be moved or

copied to your computer. Files from your computer can also be moved or copied to the R-4’s hard disk.

AC adaptor jack [DC IN]

Connect the included AC adaptor to this jack.

Cord hook

Use this to secure the AC adaptor cable.

Eject button

Press this when you want to remove the CompactFlash card inserted in the

memory card slot

.

Memory card slot [MEMORY CARD]

You can insert a CompactFlash card into this slot.

Projects you record on the R-4 can be copied to a CompactFlash card for backup or to transfer them to a

computer.

The R-4 is able to use only TYPE 1 CompactFlash memory cards. Microdrive cards are not supported.

For details on handling CompactFlash cards, refer to

“Handling memory cards”

(p. 70).

Side panel (left)

27

28

29

30

31

32

33

34

35

36

37

27

28

40

37

29

30

31

32

33

34

R-4_e.book 14 ページ２００５年２月１０日　木曜日　午後３時３６分

15

Introducing the R-4

Grounding terminal

Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or

perceive that the surface feels gritty to the touch when you touch this device, microphones connected to it,

or the metal portions of other objects. This is due to an infinitesimal electrical charge, which is absolutely

harmless. However, if you are concerned about this, connect the ground terminal (see figure) with an

external ground. When the unit is grounded, a slight hum may occur, depending on the particulars of your

installation. If you are unsure of the connection method, contact the nearest Roland Service Center, or an

authorized Roland distributor, as listed on the “Information” page.

Unsuitable places for connection

• Water pipes (may result in shock or electrocution)

• Gas pipes (may result in fire or explosion)

• Telephone-line ground or lightning rod (may be dangerous in the event of lightning)

Security Slot [ ]

http://www.kensington.com/

Headphone jack [PHONES]

Connect a set of headphones to this jack. Use the

monitor level knob

( ) to adjust the volume. If you

connect headphones, sound will not be heard from the

internal speakers

().

35

36

37

26

2

R-4_e.book 15 ページ２００５年２月１０日　木曜日　午後３時３６分

16

Introducing the R-4

fig.panel-3.eps_50

Input level select switches

Set these switches to either the MIC or LINE position depending on the type of device connected to

channels 1/L and 2/R or channels 3/L and 4/R.

Combo input jacks 1–4

These are analog audio input jacks compatible with mic preamps. They accept either XLR or 1/4” phone

plugs; you can use whichever is most convenient for the equipment you’re connecting. Balanced or

unbalanced signals can be connected.

You can use combo input jacks 1–4 as four channels of monaural input or as two stereo pairs, 1/2 and 3/4.

For details, refer to

“1 Recording Setup”

(p. 60).

* The XLR type jacks can provide 48 V phantom power, allowing you to connect phantom-powered condenser mics.

In this case, turn on the

phantom power switch

().

fig.XLR-TRS

This instrument is equipped with balanced (XLR/

TRS) type jacks. Wiring diagrams for these jacks are

shown below. Make connections after first checking

the wiring diagrams of other equipment you intend

to connect.

Line output jacks [LINE OUT]

These jacks output an analog audio signal. You can use RCA phono cables to connect them to powered

speakers, audio equipment, a mixer, etc. These jacks output the same signal as the

digital output

connector

( ) and the

headphone jack

().

The nominal output level is fixed at -10 dBV, and the volume of these jacks cannot be adjusted.

Side panel (right)

MIC

If a mic is connected

LINE

If an audio device is connected via an analog connection

38

39

40

38

39

5

1:GND

2:HOT

3:COLD

GND(SLEEVE)

HOT(TIP)

COLD(RING)

40

29

37

R-4_e.book 16 ページ２００５年２月１０日　木曜日　午後３時３６分

17

Introducing the R-4

Battery compartment

Install batteries here if you want to operate the R-4 on battery power.

The orientation in which you must insert the batteries is shown on the side of the battery compartment.

Be sure to observe the correct polarity when installing the batteries.

If you’re using the AC adaptor, there’s no need to install batteries.

Make sure to switch off the R-4’s power before you change from AC adaptor operation to battery operation,

or vice versa.

For details, refer to

“Installing batteries and turning the power on”

(p. 25).

Bottom panel

41

R-4_e.book 17 ページ２００５年２月１０日　木曜日　午後３時３６分

18

Introducing the R-4

The main screen

The R-4’s main screen provides information about the project and the operational status of the R-4.

You can press the

[DISPLAY] button

to switch the contents of the display.

fig.play-disp.eps

Display

While playing or stopped

Project name

Indicates the name of the project. If you copy WAV files from your computer

via USB to the R-4’s internal hard disk, this will show the file name. File names

containing double-byte characters (e.g., Japanese) will not be displayed cor-

rectly, but they can be played.

Time counter

Indicates the time that has elapsed from the beginning of the project to the

current location. Indicated in terms of hours: minutes: seconds.

Progress bar

Indicates the current playback location relative to the entire project.

Total time

Indicates the total time of the entire project.

Level scale

Shows the audio level of each channel in real time. The markings are relative

to 0 dBFS (Full Scale) of the digital signal. For example, 12 means -12 dBFS. C

is clipping level (0 dBFS).

Clip level indicators

Channel level meters

Channel names

This area shows up to four channel names. If you’re using one stereo channel,

this will indicate 1L and 1R. If you’re using two stereo channels, this will in-

dicate 1L, 1R, 2L, 2R.

For a monaural project, this area will show 1, 2, 3, and 4 according to the num-

ber of channels.

Output assignments

These show how the audio of each channel is assigned to the L/R output

channels. L means that the audio is assigned to the left channel, R to the right

channel, and LR to both left and right channels. Channels for which no indi-

cation appears will not be output. When you're in the main screen, you can

press the [CURSOR] up/down buttons to select the channel that you want to

monitor.

The output is sent to the PHONES jack, line output jacks, and digital output

connector.

Sampling frequency

Indicates the sampling frequency and sample size (bit depth) of the currently

selected project.

Sample size

Marker indicators

The number at the left indicates the marker located immediately before the

current time counter value. The number at the right indicates the total number

of markers assigned in the currently selected project.

Project name

Status indication

Progress bar

Power source

Total time

Time

counter

Channel

names

Output

assignments

Output level meters

Channel level meters

Sampling frequency

Sample size

(bit depth)

Marker indicators

Clip level indicators

Date and time

Level scale

dBFS

R-4_e.book 18 ページ２００５年２月１０日　木曜日　午後３時３６分

19

Introducing the R-4

In the main screen, you can press the

[DISPLAY] button

to switch the progress bar area so it shows the

remaining project time (REMAIN).

fig.play-disp2.eps

The mixer screen

From the main screen, press the

[DISPLAY] button

twice to move to the Mixer screen.

This screen lets you adjust the volume balance for monitoring.

fig.play-disp3.eps

Output level meters

These are the output level meters. They show the final output levels of the L

and R channels, to which the various channels have been mixed. You can use

the monitor level sliders of the mixer screen to adjust the level of each channel.

From the left, the level meter is calibrated at -36, -24, -12, and -6 dBFS.

Clip level indicators

Power source

Indicates how power is being supplied to the R-4. The plug icon is shown if

power is being supplied by the AC adaptor, and the battery icon is shown if

power is being supplied by batteries.

Remaining time

During playback, this indicates the remaining time from the current location

to the end of the project.

Channel level sliders

Use these to adjust the playback level of each channel. Use the left/right

[CURSOR/FINDER] buttons to select a slider, and turn the [SCRUB/VALUE]

dial to adjust the value. Each slider provides adjustment within the range 0–

120. The default value is 100.

* The settings are not stored in the project; they are remembered by the R-4

itself. When you turn off the power, the settings will revert to their default

values.

* These settings do not affect the recording levels.

Remaining time

Channel names

Channel level meters

Channel level

sliders

Output level meters

Monitor output indicators

R-4_e.book 19 ページ２００５年２月１０日　木曜日　午後３時３６分

20

Introducing the R-4

The main screen

The R-4’s main screen provides information about the project and the operational status of the R-4.

You can press the

[DISPLAY] button

to switch the contents of the display.

* For an explanation of the other indications, refer to

“While playing or stopped”

(p. 18).

From the main screen, you can press the

[DISPLAY] button

to make the recordable time area show the

remaining hard disk capacity instead.

While recording

Time counter

Indicates the elapsed time from the beginning of the project you’re recording

until the current location. Indicated in terms of hours: minutes: seconds.

Recordable time

During recording, this indicates the remaining time that recording to the hard

disk can take place. The remaining time will depend on the sampling

frequency (Sample Freq.), sample size (Rec Bit), and recording mode (Rec

Mode) settings. The indication shows how much longer you can record with

the current settings.

Total recording time

Indicates the total time from the beginning of recording to the current

location.

* Even if you record continuously, another new project will be created

automatically when the project reaches 2 GB in size, and recording will

continue. Even for a recording that spans multiple projects in this way, the

elapsed time since you first pressed the [REC] (record) button will be shown

here.

Remaining hard disk

capacity

Indicates the remaining free capacity on the internal hard disk.

Total recording time

Time counter

Recordable time

Remaining hard disk capacity

R-4_e.book 20 ページ２００５年２月１０日　木曜日　午後３時３６分

La pagina si sta caricando...

Roland R-4 Manuale utente

Roland R-4 Manuale utente

in altre lingue

Documenti correlati

Altri documenti