Intel Switch 550T Manuale utente

Categoria
Switch di rete
Tipo
Manuale utente

Questo manuale è adatto anche per

Intel
®
Express 550T
Routing Switch
User Guide
696939-004
500.book Page i Thursday, September 2, 1999 1:50 PM
Year 2000 capable
An Intel product, when used in accordance with associated documentation, is “Year 2000 Capable” when, upon installation, it ac-
curately stores, displays, processes, provides, and/or receives data from, into, and between the twentieth and twenty-first centuries,
including leap year calculations, provided that all other technology used in combination with said product properly exchanges date
data with it.
Copyright © 1999, Intel Corporation. All rights reserved.
Intel Corporation, 5200 NE Elam Young Parkway, Hillsboro, OR 97124-6497
Intel Corporation assumes no responsibility for errors or omissions in this manual. Nor does Intel make any commitment to up-
date the information contained herein.
* Other product and corporate names may be trademarks of other companies and are used only for explanation and to the owners’
benefit, without intent to infringe.
Forth edition August 1999 696939-004
500.book Page ii Thursday, September 2, 1999 1:50 PM
iii
Contents
Chapter 1 Intel Express 550T Routing Switch 1
Introduction to the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Before Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Positioning and Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing a Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting Other Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The Power Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Other LEDs on the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 2 Intel Device View 17
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Removal of Intel Device View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using Intel Device View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Before a switch is contacted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
After a Switch or Stack is Contacted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setting the Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installing and Managing Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Device Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Device View (Main Display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Diagnostics Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Trap Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
System Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Errors Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
500.book Page iii Thursday, September 2, 1999 1:50 PM
iv
CONTENTS
Chapter 3 Standard Configuration 41
Changing the Setup of the Switch or Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Internet Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Local Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Permanent Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Link Aggregation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Local Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Adaptive Forwarding Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Changing the Setup of the Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
General Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Port Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Port Specific Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Chapter 4 Advanced Configuration 65
VLANs (Virtual LANs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Routing Between VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
DVMRP Tunnels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
IP Multicast (IGMP pruning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
IP Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Chapter 5 Managing the Switch 79
Management using Intel Device View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Information about the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Monitoring the Switch’s Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Monitoring using RMON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Monitoring the Stack’s Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Monitoring VLANs and Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Monitoring the Port’s Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Tools for the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Report Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
500.book Page iv Thursday, September 2, 1999 1:50 PM
v
CONTENTS
Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Recovery Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
DNS IP Conversion Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Tools for the Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Stack Synchronization Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Switch Position Organizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Color Code Matrix Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Chapter 6 Redirect TCP Packets 111
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Setting up redirection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Monitoring the status of the cache servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Chapter 7 Technical Specifications 117
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Chapter 8 Console Port Use and Troubleshooting 123
Use of the Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Recovering from Start-up Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Using Maintenance Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Troubleshooting Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Troubleshooting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Isolating the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Further Evaluation of the Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Typical Problems and Causes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Start-up Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Performance Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Communication Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Reporting the Problem to Intel Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Retrieving Information for Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Appendix A Limited Hardware Warranty 137
Limited Hardware Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Limited Hardware Warranty (Europe only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Federal Communications Commission (FCC) Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
500.book Page v Thursday, September 2, 1999 1:50 PM
vi
CONTENTS
Manufacturer Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
AVERTISSEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
WARNUNG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
AVVERTENZA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
ADVERTENCIAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Automated Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Customer Support Technicians . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
500.book Page vi Thursday, September 2, 1999 1:50 PM
vii
Information sources for
this switch
This User Guide is one of three sources of information delivered with
this switch.
Quick Start description A printed guide that describes these basic steps:
Connect the switch
Start the switch (using the default settings)
Start Intel Device View
Change the setup
Save a new setup to the memory
Access Local Management
And, the legal declarations and warnings
User Guide description
(this guide)
A printed guide containing full instructions on how to install the
switch and operate the switch using Intel Device View.
Help description Online, context-sensitive help text for each dialog box, providing in-
formation about the permitted limits for the parameters used.
Information type... Given in...
Getting started quickly Quick Start (printed)
How to customize your switch User Guide (printed)
Context sensitive help Help (online)
Preface
500.book Page vii Thursday, September 2, 1999 1:50 PM
viii
PREFACE
viii
Warning
Electrostatic Sensitive Device
Products covered This User Guide gives you instructions on how to use:
Intel Express 550T Routing Switch
Intel Device View
Prerequisite knowledge This User Guide is intended for personnel authorized to configure and
manage local area networks. We assume that the person has an ad-
vanced technical background within data communication and net-
works.
Opening this product must be done only by a network manager or per-
son who is qualified and authorized to install electrical equipment,
and who is aware of the hazards to which he/she is exposed. This per-
son must have an advanced technical background within data com-
munications and networks.
Conventions in this manual This manual uses the following conventions:
File names, commands and examples
All file names, commands and examples are shown in the COURIER
typeface.
Menu and submenu names
Menus, for example File or View, are shown in normal typeface with
lowercase and uppercase letters displayed as shown on the screen.
0887
Electrostatic Sensitive Device
Do not handle the printed circuit board unless the working area is static-free!
500.book Page viii Thursday, September 2, 1999 1:50 PM
ix
ix
PREFACE
Access to submenus
You access submenus using a menu hierarchy. These are shown by
use of angle brackets and the courier typeface. For example,
File>Configuration>Setup shows that to select the Setup sub-
menu you must first click File and then Configuration.
Acronyms ARP Address Resolution Protocol
ASIC Application-Specific Integrated Circuit
AUI Attachment Unit Interface
BPDU Bridge Protocol Data Unit
CRC Cyclic Redundancy Check
DHCP Dynamic Host Configuration Protocol
DVMRP Distance Vector Multicast Routing Protocol
ICMP Internet Control Message Protocol
IGMP Internet Group Message Protocol (for IP Multicast)
IEEE Institute of Electrical and Electronic Engineers
IP Internet Protocol
LAN Local Area Network
MIB Management Information Base
RAM Random Access Memory
RMON Remote Monitoring
RIP Routing Information Protocol
RSVP Resource Reservation Protocol
SNMP Simple Network Management Protocol
STP Spanning Tree Protocol
TFTP Trivial File Transfer Protocol
ToS Type of Service
UDP User Datagram Protocol
VLAN Virtual Local Area Network
500.book Page ix Thursday, September 2, 1999 1:50 PM
x
500.book Page x Thursday, September 2, 1999 1:50 PM
1
In this chapter This chapter covers the following topics.
1
Intel Express 550T
Routing Switch
Topic See Page
Introduction to the product 2
Front Panel 3
Rear Panel 5
Installation 5
500.book Page 1 Thursday, September 2, 1999 1:50 PM
2
C H A P T E R 1 Intel Express 550T Routing Switch
2
Introduction to the product
Purpose of the switch The Intel Express 550T Routing Switch uses your existing network
cables to integrate switching technology into your computer network.
Each device in a workgroup or a network segment can communicate
at a full wire-speed of 10Mbps or 100Mbps to provide:
High-speed connectivity
Simultaneous two-way communication between connected
devices
Increased network throughput and performance
Increased server availability
Physical features This switch offers the following features:
Plug-and-play—no need to configure the module to use the basic
operations
8 x 10/100Mbps, non-blocking connections
Two option slots for modules
Front panel LEDs that show switch, port and traffic status
Automatic detection of 110V and 240V power supplies
Hardware features The switch offers the following features:
Each port can operate in one of three switching modes: cut-
through, fragment-free or store-and-forward
Each port supports half- and full-duplex operation
Simultaneous full wire-speed switching on all ports
RMON support for Statistics, History, Alarm, Host, HostTopN,
Matrix, Filter, Capture and Events
Full RMON support on a limited number of ports
Switch routing: IP and IPX protocols
Spanning tree support on all ports
Flow control
Permanent MAC address entries
500.book Page 2 Thursday, September 2, 1999 1:50 PM
3
3
C H A P T E R 1 Intel Express 550T Routing Switch
Software features
The switch offers the following features:
Intel Device View for Windows* 95, Windows* 98 and Windows
NT* or Intel Device View for Web
Adaptive forwarding mode
Local Management via a direct terminal connection or via TEL-
NET
SNMP Management support
BOOTP and TFTP support
Control over user access rights
Creation of virtual LANs
Stand-alone (per switch or stack) or distributed (switch network)
VLAN
IP Multicast
RSVP
ToS (Type of Service)
IP Filtering
Front Panel
Introduction The LEDs on the front panel show the status of the ports, so you
should position the switch with the front panel facing you. You can
also see which ports the cables are connected to on the switch.
View of the front panel The front panel of the switch is shown below:
971126 Awaiting Drawing from EBZ
1675
Power
Status
Temperature
RPS
123 87654
Reset
Console
9600-8-N-1
Slot BSlot A
Blink
Solid
Solid
Off
Activity
Link
100 Mbps
10 Mbps
Collision
Disabled
Full duplex
Half duplex
LEDs
LEDs
Green
Green
Orange
Orange
Port Status
Intel Express
550T Routing
Switch
500.book Page 3 Thursday, September 2, 1999 1:50 PM
4
C H A P T E R 1 Intel Express 550T Routing Switch
4
Front panel ports
These ports are on the front panel:
Slots for modules After removing one or both of the cover plates, the modules can be
inserted to expand the functionality of the switch.
Front panel LED functions The LEDs on the front panel have the following functions:
Buttons The buttons on the front panel have the following functions:
Port Function
CONSOLE port
(DB-9)
Connects a PC (running a VT100 emula-
tion), a VT100 terminal or a modem to
access the built-in Local Management pro-
gram.
8 x 10/100Base-TX
ports (RJ-45)
Connects devices using Unshielded Twisted
Pair (UTP) cabling complying to EIA568A
Category 5 or ISO/IEC 11801 Category 5
level D.
LED
Shows the status for...
Port LEDs -
Green and Orange
The operation of each port.
Status The operation of the switch.
Power The internal power supply.
Temperature The internal temperature.
RPS (redundant
power supply)
The external, redundant power supply.
Button name Function
Port Status Shows the operational status of each port.
Reset Reset or enter Maintenance Mode or Recov-
ery Mode
500.book Page 4 Thursday, September 2, 1999 1:50 PM
5
5
C H A P T E R 1 Intel Express 550T Routing Switch
Rear Panel
Introduction The rear panel has a cooling fan outlet and the main supply cable, so
you should position the switch with the rear panel facing away from
you.
View of rear panel The rear panel of the switch is shown below:
Rear panel parts The switch’s rear panel has the following parts:
Installation
Important You must adhere to all local and national regulations governing the
installation and connection of electrical devices when installing the
switch.
1741
Input
100-120VAC/2A
200-240VAC/1A
47Hz-63Hz
Redundant Power Supply (RPS)
Part Function
Fan outlet Cools the internal circuitry of the switch.
Power connection A socket to connect the power cord to the
main supply.
Redundant power
supply connector
Connects an external redundant power sup-
ply. If the internal power supply fails, the
redundant power supply starts immediately.
500.book Page 5 Thursday, September 2, 1999 1:50 PM
6
C H A P T E R 1 Intel Express 550T Routing Switch
6
Before Installation
Contents of the pack Unpack the switch carefully and check that these parts are present:
Check the package
contents
If you have not received all of the parts, or any of the parts are dam-
aged, contact your dealer immediately.
Keep all the packaging materials in case you need to repack the
switch.
Check all labels Read all labels and rating plates on the switch. If there is anything that
you do not understand, or if any of the information provided does not
appear to comply with your local or national rules and regulations,
consult your dealer before proceeding with the installation.
Essential reading It is important that you read the following:
“Late-breaking News”.
This contains essential information you should be aware of when
installing and using the product; for example, limitations and
compatibility issues.
Warnings and the instructions earlier in this guide.
The README.TXT file on the CD-ROM. This gives a general
description of the software and specific requirements.
Item Present?
One Intel Express 550T Routing Switch
One power cord (suitable for your
power outlet)
One mounting kit
One CD-ROM
One Console cable
One Quick Start
One User Guide (you are reading it)
Late-breaking News
Intel Support Service papers
500.book Page 6 Thursday, September 2, 1999 1:50 PM
7
7
C H A P T E R 1 Intel Express 550T Routing Switch
Positioning and Installing the Switch
Allow adequate ventilation The switch contains two fans to air-cool the internal circuitry. The air
is drawn in from the left of the unit and expelled through the outlet
grills on the right side and the rear.
To ensure correct airflow, leave 100 mm (4 inches) free space on both
sides and behind the switch. Do not allow the intake or outlet grills to
become blocked.
On a desktop To install the switch in a desktop environment:
1 Find the four rubber feet in the pack that contains the rack
mounting kit.
2 Remove the backing strip from each of the four feet.
3 Attach the four rubber feet to the underside of the switch (to
ensure that the switch stands firmly).
4 Place the switch on a stable, flat surface.
5 Ensure that the air intake (on the left) and fan outlets (on the
right side and rear) are not blocked.
Warning The switch’s lifetime and operational reliability can
be seriously degraded by inadequate cooling.
Rack requirements Install the switch in a standard rack in accordance with IEC297 (or
similar); if the minimum outside measurements of the rack are 600 x
600mm (23.5 x 23.5inches), you must allow 190mm (7.5 inches) of
space at the rear.
Mounting kit The switch is delivered with a kit to attach it to a standard 19-inch
equipment rack (with side support rails). The kit contains two mount-
ing brackets and four screws (for attaching the brackets to the sides
of the switch).
Tools required for
positioning in a rack
In addition to the mounting kit, you need the following items to
mount the switch in a rack:
Standard 19-inch rack with side support rails.
3 mm screwdriver.
500.book Page 7 Thursday, September 2, 1999 1:50 PM
8
C H A P T E R 1 Intel Express 550T Routing Switch
8
Customer-supplied screws for securing the switch in the rack.
Mounting screws are not provided because the required sizes
may vary from rack to rack.
In an equipment rack To mount the switch in a standard equipment rack:
1 Attach the mounting bracket marked “Left” to the left-hand side
of the switch, and attach the mounting bracket marked “Right”
to the right-hand side of the switch, using the four screws pro-
vided.
Make sure that you attach the mounting brackets to the correct
sides. Otherwise the switch will not align correctly in the
equipment rack.
2 If the four rubber feet prevent the switch from standing firmly
on the equipment rack’s side support rails, remove them.
3 Set the switch in the equipment rack, and make sure there is
adequate space for air flow around the switch (see “Allow ade-
quate ventilation” in “Positioning and Installing the Switch”, p.
7).
4 Screw the mounting brackets securely to the equipment rack.
Ambient temperature If the switch is installed in a closed or multi-rack assembly, the oper-
ating ambient temperature of the rack environment may be greater
than the ambient temperature of the room. Make sure that the temper-
ature of the rack environment does not exceed the recommended op-
erating temperature for the switch.
971126 Awaiting Drawing from EBZ
1679
Power
Intel Express
550T Routing
Switch
Status
Temperature
RPS
1
2
3
8
7
6
5
4
Reset
Console
9600-8-N-1
Slot B
Slot A
Blink
Solid
Solid
Off
Activity
Link
100 Mbps
10 Mbps
Collision
Disabled
Full duplex
Half duplex
LEDs
LEDs
Green
Green
Orange
Orange
Port Status
500.book Page 8 Thursday, September 2, 1999 1:50 PM
9
9
C H A P T E R 1 Intel Express 550T Routing Switch
Installing a Module
Introduction You can increase the connectivity options of your switch by installing
a module.
Warning Modules are not designed to be installed in, or removed
from, the switch while it is in operation. You must
power off the switch before attempting to install or
remove a module.
Static-free working area The module’s printed circuit board is an Electrostatic Sensitive De-
vice and should be handled only in a static-free working area; other-
wise, the printed circuit board may fail or be degraded.
Avoiding damage to the
circuit board
If you remove the plate covering the slot on the front of the switch,
for example, to install or remove a module, follow this procedure to
avoid damage to your printed circuit board:
Warning Do not remove the plate unless the switch is discon-
nected from the main power supply.
1 Disconnect the switch from the main power supply.
2 Ground the switch before you handle the printed circuit board.
3 Connect yourself to a non-painted/non-isolated part of the
grounded switch (for example the back panel) using a wrist
strap with 1M resistance to ensure that you carry the same
electrostatic charge as the enclosure.
4 Remove the plate covering the slot.
Installing a module To install a module:
1 If the switch is already operational, disconnect it from the main
power supply.
2 Follow the instructions in “Avoiding damage to the circuit
board” above.
3 Unscrew the screws of the plate covering the slot on the front of
the switch. Save these screws and plate.
4 Insert the module into the slot (following the instructions in the
module’s User Guide). Place your thumbs just beneath the
screws on the front panel of the module and push in the module.
Secure it using the retaining screws.
500.book Page 9 Thursday, September 2, 1999 1:50 PM
10
C H A P T E R 1 Intel Express 550T Routing Switch
10
Removing the module
To remove a module:
1 If the switch is already operational, disconnect it from the main
power supply.
2 Follow the instructions in “Avoiding damage to the circuit
board” above.
3 Unscrew the screws securing the module.
4 Pull the module gently to disengage the connectors fully from
the socket on the motherboard. Slide the module out com-
pletely.
5 Cover the empty module port with the plate and secure using
the screws.
Connecting Other Devices
Introduction Incorrect cabling is often the cause of network configuration prob-
lems
Use shielded cables Shielded cables normally comply with EMC and FCC emission lim-
its.
Only use unshielded cables when it is explicitly specified in the in-
stallation manual of the device in question.
Cables for the LAN Ports Ports on the switch are wired MDI-X, so use the following cable:
If you connect the switch to a... Then use a...
Workstation or server Straight-through cable 1:1
Device with MDI-X ports (for exam-
ple another Intel switch or hub)
Crossover cable
Device with MDI ports Straight-through cable 1:1
500.book Page 10 Thursday, September 2, 1999 1:50 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162

Intel Switch 550T Manuale utente

Categoria
Switch di rete
Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue