Bosch HGS8645UC Guida d'installazione

Marca: Bosch

Modello: HGS8645UC

Categoria: Fornelli

Tipo: Guida d'installazione

Questo manuale è adatto anche per

Installation Manual

Free-standing range

HGS8055UC, HGS8045UC, HGS8655UC, HGS8645UC

ö Installation Instructions

9 Safety Definitions ..................................................... 3

IMPORTANT SAFETY INSTRUCTIONS ........................ 4

Appliance Handling Safety ................................................. 5

Safety Codes and Standards ............................................. 5

Electric Safety ....................................................................... 5

Gas Safety ............................................................................. 6

Propane Gas Installation ..................................................... 6

Related Equipment Safety .................................................. 6

Conversion to Propane Gas ............................................... 7

High Altitude Installation ..................................................... 7

Before You Begin .......................................................... 8

Tools and Parts Needed ..................................................... 8

Parts Included ....................................................................... 8

Removing Packaging .......................................................... 8

General Information ............................................................. 9

Cabinet Requirements ......................................................... 9

Technical Data ................................................................... 10

Installation Checklist ......................................................... 11

Installation Procedure ................................................ 11

How to Remove the Oven Door ..................................... 11

Fitting the Rear Vent Trim ................................................ 12

Fitting the Adjustable Feet ............................................... 12

Connect Gas Supply ........................................................ 13

Install Appliance ................................................................ 14

Connect Electrical Supply ............................................... 16

Burner Cap Placement ..................................................... 16

Check the Installation ....................................................... 17

Test for Gas Leaks ............................................................ 17

Conversion to Propane Gas (LPG) ............................ 18

Technical Service ........................................................ 23

How to Obtain Warranty Service .................................... 23

Wiring Diagram for HGS8..5UC .................................. 24

9 Safety Definitions

Safety Definitions

9 WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or

property may occur as a result of non-compliance with

this advisory.

Note: This alerts you to important information and/or

tips.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFET Y I NS T RUCT I ONSRE AD AND SAVE THESE INSTRUCTIONS

Gas Appli ance Safety

'RQRWVWRUHRUXVHJDVROLQHRURWKHUIODPPDEOH

YDSRUVDQGOLTXLGVLQWKHYLFLQLW\RIWKLVRUDQ\

RWKHUDSSOLDQFH

:+$772'2,)<2860(//*$6

'RQRWWU\WROLJKWDQ\DSSOLDQFH

'RQRWWRXFKDQ\HOHFWULFDOVZLWFK

'RQRWXVHDQ\SKRQHLQ\RXUEXLOGLQJ



,PPHGLDWHO\FDOO\RXUJDVVXSSOLHUIURPD

QHLJKERU·VSKRQH)ROORZWKHJDVVXSSOLHU·V

LQVWUXFWLRQV

,I\RXFDQQRWUHDFK\RXUJDVVXSSOLHUFDOO

WKHILUHGHSDUWPHQW

,QVWDOODWLRQDQGVHUYLFHPXVWEHSHUIRUPHG

E\DTXDOLILHGLQVWDOOHUVHUYLFHDJHQF\RUWKH

JDVVXSSOLHU



:$51,1*,IWKHLQIRUPDWLRQLQWKHVHLQVWUXFWLRQV

LVQRWIROORZHGH[DFWO\DILUHRUH[SORVLRQPD\

UHVXOWFDXVLQJSURSHUW\GDPDJHSHUVRQDOLQMXU\

RUGHDWK

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT: THE APPLIANCE MUST BE INSTALLED BY

A QUALIFIED INSTALLER.

INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE

APPLIANCE AFTER INSTALLATION IS COMPLETE.

IMPORTANT: SAVE FOR THE LOCAL INSPECTOR’S

USE.

WARNING

If the information in this manual is not followed exactly,

fire or shock may result causing property damage or

personal injury.

WARNING

Do not repair, replace or remove any part of the

appliance unless specifically recommended in the

manuals. Improper installation, service or maintenance

can cause injury or property damage. Refer to this

manual for guidance. All other servicing should be done

by an authorized service provider.

Improper installation is not covered by the warranty.

WARNING

TIP OVER HAZARD

Appliance Handling Safety

Wear gloves to avoid cutting fingers on sharp edges

during Installation.

Unit is heavy and requires at least two persons or proper

equipment to move.

Do not lift appliance by the oven door handle. Remove

the oven door for easier handling and installation See the

section "Removing/Replacing the Oven Door".

Do not use the oven for storage.

Safety Codes and Standards

This appliance complies with one or more of the

following Standards:

ANSI Z21.1/ CSA 1.1Household Cooking Gas

Appliances

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Installation must conform with local codes or, in the

absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54or, in Canada, the Natural

Gas and Propane Installation Code, CSA B149.1.

The appliance must be electrically grounded in

accordance with local codes or, in the absence of local

codes, with the National Electrical Code, NFPA 70latest

edition or, in Canada, the Canadian Electric Code, CSA

C22.1-02.

Electric Safety

WARNING

Before you plug in an electrical cord or turn on power

supply, make sure all controls are in the OFF position.

Be sure your appliance is properly installed and

grounded by a qualified technician. Installation, electrical

connections and grounding must comply with all

applicable codes.

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being turned

ON accidentally.

For appliances equipped with a cord and plug, do not

cut or remove the ground prong. It must be plugged into

a matching grounding type receptacle to avoid electrical

shock. If there is any doubt as to whether the wall

receptacle is properly grounded, the customer should

have it checked by a qualified electrician.

Do not use an extension cord.

Do not use an adapter.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

A child or adult can tip the

range over and be killed.

Install the anti-tip device

to the structure and/or the

range. Verify the anti-tip

device has been properly

installed and engaged.

Engage the range to the

anti-tip device. Ensure the

anti-tip device is re-

engaged when the range

is moved.

Re-engage the anti-tip device if the range is moved.

Do not operate the range without the anti-tip device

in place and engaged.

See installation instructions for details.

Failure to follow the instructions in this manual can

result in death or serious burns to children and

adults.

Check for proper installation and use of the anti-tip

bracket. Carefully tip the range forward pulling from

the back to ensure that the anti-tip bracket engages

the range leg and prevents tip-over. The range

should not move more than 1” (2.5cm).

Hidden surfaces may have sharp edges.

Use caution when reaching behind or

under appliance.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

The circuit breaker should have a contact separation of

at least 3mm on all poles.

Installer – show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Refer to rating label for more information. See "How to

Obtain Warranty Service" under "Technical Service" for

rating label location.

Gas Safety

Install a gas shutoff valve near the appliance. It must be

easily accessible in an emergency.

Leak testing must be conducted by the installer

according to the instructions in this manual.

The appliance and its individual shutoff valve must be

disconnected from the gas supply piping system during

any pressure testing at pressures in excess of ½ psi

(3.5kPa).

The appliance must be isolated from the gas supply

piping system by closing its individual manual shutoff

valve during any pressure testing of the gas supply

piping system at test pressures equal to or less than

½ psi (3.5 kPa).

The minimum supply pressure must be 1" water column

above the manifold pressure printed on the rating label.

The maximum supply pressure must not exceed

14.0inches water column (34.9 Millibars).

IMPORTANT SAFETY NOTICE: Burning gas cooking fuel

generates some by-products which are on the list of

substances which are known by the State of California to

cause cancer or reproductive harm. To minimize

exposure to these substances, always operate this unit

according to the instructions contained in this booklet

and provide good ventilation.

Proposition 65Warning:

This product may contain a chemical known to the State

of California, which can cause cancer or reproductive

harm. Therefore, the packaging of your product may

bear the following label as required by California:

Propane Gas Installation

The propane gas tank must be equipped with its own

high pressure regulator. In addition, the regulator

supplied with this unit must also be used.

The appliance is shipped from the factory for use with

natural gas. It must be converted for use with propane. A

qualified technician or installer must do the conversion.

This appliance has been certified for safe operation up to

a height of 10,000 ft. Exception: To use it with propane

gas, the appliance must be converted in accordance with

the propane conversion instructions.

For Massachusetts installations:

▯ Installation must be performed by a qualified or

licensed contractor, plumber or gas fitter qualified or

licensed by the state, province or region where this

appliance is being installed.

▯ Shut-off valve must be a “T” handle gas cock.

▯ Flexible gas connector must not be longer than

36 inches.

Installer - show the owner where the gas shut-off valve is

located.

Related Equipment Safety

The appliance should only be used if installed by a

qualified technician in accordance with these installation

instructions and all applicable regulations and codes.

The manufacturer is not responsible for damages

resulting from incorrect installation.

Remove all tape and packaging before using the

appliance. Destroy the packaging after unpacking the

appliance. Never allow children to play with packaging

material.

Never modify or alter the construction of the appliance.

For example, do not remove leveling legs, panels, wire

covers or anti-tip brackets/screws.

To eliminate the risk of burns or fire by reaching over

heated surface units, cabinet storage space located

above the surface units should be avoided. If cabinet

storage is to be provided, the risk can be reduced by

installing a hood that projects horizontally a minimum of

5inches (127 mm) beyond the bottom of the cabinet.

Verify that cabinets above the cooktop are a maximum of

13" (330 mm) deep.

When installing a cooktop over a single oven, be sure to

follow both the oven’s and cooktop’s installation

manuals.

Ventilation Recommendations

We strongly recommend the installation of a ventilation

hood above this appliance. The hood must be installed

according to instructions furnished with the hood.

CAUTION

The appliance should not be installed with a ventilation

system that blows air downward toward the burners. This

type of ventilation system may cause ignition and

combustion problems with the gas cooking appliance

resulting in personal injury or unintended operation.



&DQFHUDQG5HSURGXFWLYH+DUPZZZ3:DUQLQJVFDJRY

67$7(2)&$/,)251,$352326,7,21:$51,1*

:$51,1*

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Conversion to Propane Gas

WARNING

Personal injury or death from electrical shock may occur

if the appliance is not installed by a qualified installer or

electrician.

Any additions, changes or conversions required in order

for this appliance to satisfactorily meet the application

needs must be made by a qualified technician.

High Altitude Installation

This appliance has been tested for operation up to an

altitude of 10,000ft (3,048m) elevation above sea level.

If desired, for altitudes above 2,000 ft (610 m) elevation

above sea level, adjustments may be made. Burners

should be checked at the lowest setting, if the flame is

not stable the simmer should be increased until the

flame is stable. This can be done by adjusting the

bypass screw in the valve. If flame performance is

satisfactory, adjustment will not be required. It is required

that a Certified Professional make the high altitude

adjustments during installation.

Before You Begin

Tools and Parts Needed

▯ Phillips head screwdriver

▯ Slotted screwdriver 1/8" (3,5 mm)

▯ Adjustable wrench

▯ Tongue and groove pliers

▯ Socket or flat wrench 3/8” (10mm) or tongs

▯ Socket or flat wrench 7/8” (22mm) or tongs

▯ Drill with 5/16" (8mm) bit

▯ Pencil

▯ Tape measure

Note: Additional materials may be necessary for

installation in solid surface countertops. Contact the

countertop manufacturer.

Parts Included

30”:

* Attached to the appliance.

36”:

* Attached to the appliance.

Removing Packaging

See the diagram on the packaging.

▯ If straps are present, cut the straps.

▯ Cut plastic down back of unit making sure not to cut

the unit.

▯ Remove plastic film.

▯ Lift the cardboard carton from the top of the range and

dispose of.

▯ Remove the corner posts, making sure that any other

packing materials running between the corner posts

are also removed.

▯ Remove all internal packaging and tape.

▯ The rear vent trim is nested in the styrofoam

packaging for shipping purposes. Do not throw away.

[[ [





[[ [





General Information

30”:

36”:

Cabinet Requirements

X = Grounded Outlet

Y = Gas Supply Line

The minimum spaces that must be maintained when

installing the gas cooktop shall be:

èʌʓʘ



èʌʓʘ



ʎʓʘ



ʐʓʘ



èʔ



ʌʚ



èʌʓʘ



ʐʓʘ

²ʐʓʘ

²

èʋʓʘ

²æʓʘ

²

èʌʓʘ



ʌʓʘ



ʎʓʘ



ʐʓʘ



èʔ



èʋʓʘ



èèʓʘ

²èæʓʘ

²

ʐʓʘ

²ʐʓʘ

²

ʎʚ



B minimum 18" (457 mm)

C minimum 30" (762 mm) clearance between

the top of the cooking surface and the

bottom of the unprotected wood or metal

cabinet

D 30": minimum 30" (762 mm)

36": minimum 36" (914 mm)

E minimum 25" (635 mm)

F maximum 13" (330 mm)

G 30": minimum 30" (762 mm)

36": minimum 36" (914 mm)

Zero clearance between adjacent

combustible construction below the

countertop surface and sides of the

appliance.

H 35"6/16- 36"10/16(898- 930 mm)

I 11" (279 mm)

J 7" (178 mm)

K 6" (150 mm)

L 11" (279 mm)

(

)

[

Choose one of the following built-in configurations.

Installation allowed only with non combustible back

wall

▯ Option 1: A >= 12'' (305 mm) and B >= 28'' (711 mm)

▯ Option 2: A >= 28'' (711 mm) and B >= 12'' (305 mm)

* Clearances from non-combustible materials are not

part of the ANSI Z21.1scope and are not certified by

“Intertek”. Clearances of less than 3'' (76 mm) should be

approved by the local codes and/or by the local authority

having jurisdiction.

Island Installation (applicable both with non

combustible back wall and combustible back wall)

▯ Option 1: A >= 12'' (305 mm) and B >= 28'' (711 mm)

▯ Option 2: A >= 28'' (711 mm) and B >= 12'' (305 mm)

* purchased separately

** Clearances from non-combustible materials are not

part of the ANSI Z21.1scope and are not certified by

“Intertek”. Clearances of less than 3'' (76 mm) should be

approved by the local codes and/or by the local authority

having jurisdiction.

Low Backguard Installation (applicable both with non

combustible back wall and combustible back wall)

▯ Option 1: A >= 12'' (305 mm) and B >= 28'' (711 mm)

▯ Option 2: A >= 28'' (711 mm) and B >= 12'' (305 mm)

* purchased separately

** Clearances from non-combustible materials are not

part of the ANSI Z21.1scope and are not certified by

“Intertek”. Clearances of less than 3'' (76 mm) should be

approved by the local codes and/or by the local authority

having jurisdiction.

Technical Data

30” (5burners):

36” (6burners):

Oven:



PLQ





Total connected load, electric 1 A (120 W)

Total connected load, gas

(natural gas)

48,000 BTU/h

(14.1 kW)

Total connected load, gas

(propane gas)

48,000 BTU/h

(14.1 kW)

Total connected load, electric 1 A (120 W)

Total connected load, gas

(natural gas)

63,000 BTU/h

(18.4 kW)

Total connected load, gas

(propane gas)

63,000 BTU/h

(18.4 kW)

Bake burner

Total connected load gas (nat-

ural gas/propane gas)

17,000 BTU/h

(5.0 kW)

Broiler, 30” range

Total connected load gas (nat-

ural gas/propane gas)

11,500 BTU/h

(3.4 kW)

Broiler, 36” range

Total connected load gas (nat-

ural gas/propane gas)

14,000 BTU/h

(4.1 kW)





Installation Checklist

Please refer to the pages following for complete

installation instructions. Use this checklist to verify that

you have completed each step of the installation

process. This can help you avoid mistakes.

Installation Procedure

Installati on Procedure

An air curtain or other overhead range hood, which

operates by blowing a downward airflow onto a range,

shall not be used in conjunction with the gas range

unless the hood and range have been designed and

tested in accordance with ANSI Z21.1and listed by an

independent testing laboratory for combination use.

How to Remove the Oven Door

9 WARNING

▯ Make sure the oven is cool and the power to the

oven has been turned off before removing the

door. Failure to do so could result in electrical

shock or burns.

▯ The oven door is heavy and parts of it are fragile.

Use both hands to remove the oven door. The

door front is glass. Handle carefully to avoid

breaking.

▯ Grasp only the side of the oven door. Do not

grasp the handle as it may swing in your hand

and cause damage or injury.

▯ Failure to grasp the oven door firmly and properly

could result in personal injury or product damage.

▯ To avoid injury from the hinge bracket snapping

closed, make sure that both levers are securely in

place before removing the door. Also, do not

force the door open or closed – this could

damage the hinge or result in injury.

▯ Do not place the removed door down on sharp or

pointed objects as this could break the glass. Lay

on a flat, smooth surface, positioned so that the

door cannot fall over.

To avoid injury or damage, make sure that you read the

above WARNING before attempting to remove the oven

door.

Open the oven door to its fully open position.

Lock the two hinges on the left and right using the

locking pin. The locking pins must be fully inserted into

the holes in the hinges.

Installation step

Before installing the range, be sure to verify the

cabinet dimensions are correct for your unit and

that the required electrical and gas connections

are present.

Before installing the range, make sure that any

opening in the wall behind the appliance and in

the floor under the appliance shall be sealed.

Refer to the installation manual for content

regarding Safety, Cabinet Dimensions, Remov-

ing Packaging, Electrical Installation, Gas Con-

nection, and Customer Service.

Removing the oven door prior to installation

reduces the unit weight and makes the range

easier to move. Additionally, the removal of the

oven door provides access to handholds for lift-

ing.

Fitting the adjustable feet.

Move the range (2people needed) into place in

front of the installation opening, leaving the bot-

tom packaging on the unit to avoid damaging

flooring.

Plug the range into a properly configured recep-

tacle.

Protect the flooring from damage, then slide the

unit all the way into place, making sure to route

the power cord correctly.

Reinstall the oven door.

Installation step

Close the oven door until it catches on the hinge stop

levers, locking the hinges at the correct angle for door

removal. The door can be removed when it is pulled

up from the open position by about 8 inches

(203 mm). This takes the tension off the spring-loaded

hinges so that the door can be easily lifted out.

9 CAUTION

RISK OF PINCHING

Closing the door by 8" (203 mm) takes the

pressure off the spring. If this is not done, the

door can still be removed but the latch will now

slam shut and will pinch or cut your hand.

The door is heavy. Use both hands to firmly grip it by

the sides. Do not grip the door by the handle. Keeping

the angle of the door the same, lift the door straight up

approximately 3/4" (19 mm) to unhook the hinges

from the slots, and then pull it out towards you until the

hinges are clear of the oven housing.

Place the door in a convenient and stable location for

cleaning.

Refit the door in the reverse order in which it was

removed.

Fitting the Rear Vent Trim

The rear vent trim is nested in the styrofoam

packaging. Remove the packaging and the protective

film from the rear vent trim.

Place the rear vent trim into the holes intended for this

purpose using the dowel pins.

Insert and tighten the enclosed screws from below.

Fitting the Adjustable Feet

Remove all parts that are not permanently fixed,

especially the pan supports and burners.

Remove the accessories from the oven.

9 CAUTION

Protect the floor.

Tilt the appliance and put it to the floor on the

backside.

9 CAUTION

Do not use the door handle or projecting control

panel for carrying.

´



Screw the adjustable feet into the mounting holes on

the underside of the appliance.

Note: If the appliance needs to be moved again,

screw the adjustable feet in fully.

Carefully move the appliance back on the feets.

Turn the adjustable feet to align the appliance.

Note: Measure the installation height of the cabinetry

and adjust appliance height accordingly prior to

placing appliance in cabinetry.

Connect Gas Supply

The appliance is shipped from the factory for use with

natural gas at a pressure of 5" of the water column.

When checking for proper operation of the regulator, the

inlet pressure must be at least 1" greater than the

operating (manifold) pressure above. When used with

natural gas, the pressure supplied to the regulator must

be between 6" and 10,5" of the water column.

To convert the appliance to propane gas see

“Conversion to propane gas (LPG)”. A qualified

technician or installer must do the conversion.

Use a flexible gas pipe with a length of at least 5 ft

(1.5 m).

The gas inlet to the unit is located at the right rear of the

appliance.

Install the pressure regulator (supplied with unit) to gas

inlet. Postion the gasket (supplied with unit) in between

the inlet and the regulator. Position the regulator to have

it cap D (~ Page 19) easily accessible. Turn the nut on

gas inlet to hand tighten plus 1/3 turn.

Install the gas pipe to the regulator using Teflon tape or

pipe-joint compound (resistant to propane gas and

natural gas). Turn to hand tighten plus 1/3turn. Do not

exceed 1 turn for alignment, to prevent possible damage

to the gas pressure regulator.

Check inlet fittings and regulator for leaks.

* Attached to the appliance.

9 WARNING

Do not attempt any adjustment of the pressure

regulator, except when converting to propane.

Adjustments could lead to leaks or cause incorrect

gas pressure to the appliance.

Side and Back View Gas Cooker Installation

Gas Location

Connect the gas supply line to the unit pressure

regulator using a 1/2” flex gas line connector between

manual shut-off valve and pressure regulator. A metal

flex line or fixed metal pipe shall be used to connect gas

to the appliance. If a metal gas line cannot be used,

consult your local certified electrician or local electric

codes for proper grounding.

A Gas connection

B Electrical connection



Check supply line connections for leaks using a soap

solution or non-corrosive leak detection fluid. Do not use

a flame of any sort.

9 WARNING

Install a gas shut off valve near the appliance. After

installation, it must be easily accessible in an

emergency.

Turn on gas.

Apply a soap solution or non-corrosive leak detection

fluid to all joints and fittings in the gas connection

between the shut-off valve and the cooktop. Include

gas fittings and joints in the cooktop if connections

may have been disturbed during installation. Bubbles

appearing around fittings and connections indicate a

leak.

If a leak appears, turn off supply line gas shut-off valve

and tighten connections.

Retest for leaks by turning on the supply line gas shut-

off valve. When leak check is complete (no bubbles

appear), test is complete.

Wipe off all soap solution or detection fluid residue.

Important Notes for Gas Connection:

▯ The appliance and its individual gas shutoff valve must

be disconnected from the gas supply piping system

during any pressure testing of that system at test

pressures in excess of 1/2psi (3.5kPa).

▯ The appliance must be isolated from the gas supply

piping system by closing its individual manual shut-off

valve during any pressure testing of the gas supply

piping system at test pressures equal to or less than

1/2psi (3.5kPa).

Install Appliance

9 WARNING

TIP OVER HAZARD

Installing the anti-tip bracket

Ensure that the electrical connection and the gas

connection are in the correct position.

Assemble the bracket.

A child or adult can tip the

range over and be killed.

Install the anti-tip device

to the structure and/or the

range. Verify the anti-tip

device has been properly

installed and engaged.

Engage the range to the

anti-tip device. Ensure the

anti-tip device is re-

engaged when the range

is moved.

Re-engage the anti-tip device if the range is moved.

Do not operate the range without the anti-tip device

in place and engaged.

See installation instructions for details.

Failure to follow the instructions in this manual can

result in death or serious burns to children and

adults.

Check for proper installation and use of the anti-tip

bracket. Carefully tip the range forward pulling from

the back to ensure that the anti-tip bracket engages

the range leg and prevents tip-over. The range

should not move more than 1” (2.5cm).

Align the base of the hook of the bracket with the base

on the slot of the rear wall fastening bracket. Align the

base of the fastening bracket with the ground and

tighten the screws to fix the measurements.

For wall mounting, proceed with steps 5–7and 10.

For floor mounting, proceed with steps 8–9and 10.

Use the specified distance from the side of the

appliance to the bracket holes.

Move the bracket onto the wall and fix with the two

washers and screws. A qualified technician must verify

suitability of the materials in accordance with the type

and condition of the wall.

Use the following distances for the distance from the

side of the appliance to the bracket holes.

After having positioned and leveled the appliance,

move the bracket close to the rear of the appliance

and anchor it to the floor with the two washers and

screws. A qualified technician must verify suitability of

the materials in accordance with the type and

condition of the floor.

Push the cooker towards the wall, and at the same

time, insert the bracket in the plate fastened to the rear

of the appliance.

çʓʘ

èʚ



ʎʓʘ

ʌʚ

9 WARNING

The rear vent trim has 3/16” (5 mm) standoffs to

keep the appliance slightly off of the back wall.

Do not remove or tamper with standoffs due to

potential temperature issues.

10.

Check for proper installation and use of the anti-tip

bracket. Carefully tip the range forward pulling from

the back to ensure that the anti-tip bracket engages

the range leg and prevents tip-over. The range should

not move more than 1” (2.5cm).

Connect Electrical Supply

9 WARNING

Before you plug in an electrical cord or turn on

power supply, make sure all controls are in the OFF

position.

Before connecting the 5 ft (1.5 m) supply cord to a wall

receptacle, make sure that the gas shut-off valve and all

burner controls are in the OFF position.

9 WARNING

ELECTRICAL GROUNDING INSTRUCTIONS

This appliance is equipped with a three-prong

grounding plug to protect you against the risk of

shocks and it should be plugged directly into a

properly grounded receptacle. Do not cut or remove

the grounding prong from this plug.

Burner Cap Placement

Sealed burners

Your new cooktop has sealed gas burners. There are no

burner parts under the cooktop to clean, disassemble or

adjust. Your cooktop has three different burner sizes:

small, large and dual-flame.

9 WARNING

To prevent flare-ups, do not use the cooktop without

all burner caps and all burner grates properly

positioned.

9 WARNING

To prevent burns, do not touch burner caps

orgrates while hot. Turn the cooktop off and allow

the burners to cool.

The burner parts must be correctly positioned for the

cooktop to function properly. If the burner parts are not

correctly positioned, one or more of the following

problems may occur:

▯ Burner flames are too high.

▯ Flames shoot out of burners.

▯ Burners do not ignite.

▯ Burner flames light unevenly.

▯ Burner emits gas odor.

Burner Cap and Burner Base Placement

After electrical connection is complete, place each

burner base on the corresponding location on the

cooktop. One of the three bars on the burner base

should line up with the notch and prevent the base from

rotating. The small hole or cutout near the edge should

also line up with the igniter. Pay special attention to avoid

damaging the igniter during installation of the base. See

Illustration below.

Once each base is located and resting evenly, place

each burner cap on its correct burner base. See

Illustration.

Place burner cap gently on top of base so that the

prongs of the burner base fit snugly into the groove of

the burner cap.

If the maintop is removed by a certified installer (for

example to check electrical or piping connection) the

panhead screws that were removed must be re-installed

to ensure proper functionality of burners.

Checking Burner Cap Placement

Check to make sure that there is no gap between the

burner cap and burner base. See illustration below for

correct and incorrect placements of the burner cap.

You may gently try to move the burner cap from side to

side to check if it is properly placed. If properly placed,

the cap will click from side to side as the prongs hit the

groove ridge.

Install Grates

First position the outer grates, followed by the the central

grate. If you only have two grates, the order in which you

position them is not relevant.

Check the Installation

Place each correct-sized burner cap in its seated,

notched position and check the operation of the electric

igniters. Check the flame characteristics. The flame

should be blue with a minimal yellow tip on the outer

cone of the flames.

Checking the flame characteristics

Note: If the flame is completely or mostly yellow, verify

that the regulator is set for the correct fuel. Retest after

adjustment.

Some yellow streaking is normal during the initial start-

up. Allow the appliance to operate for 4–5 minutes and

reevaluate before making adjustments.

Test for Gas Leaks

9 WARNING

RISK OF FIRE

Never check for gas leaks with a flame.

Leak testing is to be conducted by the installer according

to the instructions given in this section.

Turn on gas.

Apply a non-corrosive leak detection fluid. Include all

joints and fittings between the shutoff valve and the

appliance. Include gas fittings and joints in the

appliance if connections may have been disturbed

during installation.

Inspect for leaks. Bubbles appearing around fittings

and connections indicate a leak.

If a leak appears, turn off supply line gas shutoff valve

and tighten connections.

Retest for leaks. Turn gas back on at supply line

shutoff valve and reapply leak detection fluid.

When no bubbles appear, test is complete. Wipe off all

detection fluid residue.

Yellow flames:

Further adjustment is

required.

Yellow tips on outer

cones:

Normal for propane gas

Soft blue flames:

Normal for natural gas

Orange flames:

Can be normal if certain

types of humidifiers are

used in the home. Flames

should return to blue with-

out the humidifier running.

Conversion to Propane Gas (LPG)

Always provide adequate gas supply.

This appliance is shipped from the factory for use with

natural gas. Use this kit to convert the appliance for

propane gas use if necessary. Observe the following:

Ensure that the range is converted for use with the

appropriate gas before using it.

This appliance is designed to operate at a pressure of

10" of the water column when used with propane gas.

When checking for proper operation of the regulator, the

inlet pressure must be at least 1" greater than the

operating (manifold) pressure above. When converting

for propane gas use, the pressure supplied to the

regulator must be between 11" and 13" of the water

column.

The pressure regulator that is located in the inlet of the

range manifold must remain in the supply line.

Use a flexible metal appliance connector or rigid pipe to

connect the range to the gas supply. The connector

should have an inner diameter of 1/2” and be 5 ft

(1.5 m) or less in length. (Exception: Maximum connector

length in Massachusetts installations is 3 ft (0.9 m)). In

Canada, the connector must be single-wall metal and not

longer than 6 ft (1.8 m).

Save the orifices removed from the appliance for future

use.

9 CAUTION

The gas supply shall be shut off prior to

disconnecting the electrical power, before

proceeding with the conversion.

Parts included with propane gas nozzle set:

▯ 1x nozzle number 117

▯ 1x nozzle number 48

▯ 4x nozzle number 94

▯ 2x nozzle number 65

▯ 1x nozzle number 120

▯ 1x nozzle number 110

▯ 1x adhesive label

30”

36”

No. Designation

(

Dual-flame burner (18,000 BTU/ 5.3 kW)

LPG nozzles: 117 (external) and 48 (internal)

Small burner (5,000 BTU/ 1.5 kW)

LPG nozzle: 65

Large burner (10,000 BTU/ 2.9 kW)

LPG nozzle: 94

Bake burner (17,000 BTU/ 5.0 kW)

LPG nozzle: 120

Broiler, 30” range (11,500 BTU/ 3.4 kW)

LPG nozzle: 98

Broiler, 36” range (14,000 BTU/ 4.1 kW)

LPG nozzle: 100

Orifices

Setting the pressure regulator for propane gas

Use tongue and groove pliers to remove regulator

cap D.

Unscrew the plastic regulator stem from the regulator

cap D.

Invert the plastic regulator stem and screw it in tightly.

Replace cover cap D and tighten with tongue &

groove pliers.

When converting for propane gas use, the pressure

supplied to the regulator must be between 11" and

13" of the water column.

Replacing the main control nozzles

Remove the grates.

Remove the burner cover A and burner cup B from the

burner C.

Type of gas Pressure

in W.C.P.

Burner Type Nozzle

Number

Bypass Min Power Max Power

Natural gas 5” Dual-flame burner external 180(S4) Gap 1000 BTU

(0.3 kW)

18000 BTU

(5.3 kW)

Dual-flame burner internal 75 Gap

Large burner 145 Gap 2400 BTU

(0.7 kW)

10000 BTU

(2.9 kW)

Small burner 100 Gap 1000 BTU

(0.3 kW)

5000 BTU

(1.5 kW)

Oven burner (bottom) 180 Gap 3500 BTU

(1.0 kW)

17000 BTU

(5.0 kW)

Oven broiler burner 30” range 150 Gap - 11500 BTU

(3.4 kW)

Oven broiler burner 36” range 165 Gap - 14000 BTU

(4.1 kW)

Liquid gas 10” Dual-flame burner external 117 55 1000 BTU

(0.3 kW)

18000 BTU

(5.3 kW)

Dual-flame burner internal 48 30

Large burner 94 45 2400 BTU

(0.7 kW)

10000 BTU

(2.9 kW)

Small burner 65 30 1000 BTU

(0.3 kW)

5000 BTU

(1.5 kW)

Oven burner (bottom) 120 53 3500 BTU

(1.0 kW)

17000 BTU

(5.0 kW)

Oven broiler burner 30” range 98 - - 11500 BTU

(3.4 kW)

Oven broiler burner 36” range 110 - - 14000 BTU

(4.1 kW)

Remove the nozzle D and replace it with an

appropriate nozzle for the new type of gas.

Standard-output burner/high-output burner

Double-ring high-output burner

Place the burner cup B onto the burner C and place

the burner cover A onto the burner cup B.

Refit the grates.

Setting the minimum gas flow

Remove the control knob and knob ring.

Turn the inner setting screw clockwise gently until it

bottoms out.

Note: In case of conversion from propane gas to

natural gas, turn out all bypass nozzles for 1/2 turn.

Small burner/large burner

Dual-flame burner:

Replace the control knobs.

Light each burner individually and check for flame

stability on low setting.

If required, loosen the setting screw to increase the

gas flow.

Ensure that the flame does not go out when the gas

flow is quickly changed between maximum and

minimum, and vice versa. The optimum setting is

achieved when the height of the small flame is

approx. 1/8" (3to 4 mm).

Refit the control knob and knob ring for the gas

burner.

Repeat steps 2to 8until all of the gas burners have

been set.

Connect the appliance to the power supply.









La pagina sta caricando ...

Bosch HGS8645UC Guida d'installazione

Marca: Bosch

Modello: HGS8645UC

Categoria: Fornelli

Tipo: Guida d'installazione

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Bosch HGS8645UC Installation guide
français: Bosch HGS8645UC Guide d'installation

Bosch HGS8645UC Guida d'installazione

Questo manuale è adatto anche per

Bosch HGS8645UC Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti