LevelOne WNC-0610 Manuale utente

Categoria
Schede di interfaccia / adattatori
Tipo
Manuale utente
LevelOne
WNC-0610
300Mbps N_Max Wireless PCI Card
User Manual
V1.0
Regulatory notes and statements
Wireless LAN, Health and Authorization for use
Radio frequency electromagnetic energy is emitted from
Wireless LAN devices. The energy levels of these
emissions however are far much less than the
electromagnetic energy emissions from wireless devices
like for example mobile phones. Wireless LAN devices are
safe for use frequency safety standards and
recommendations. The use of Wireless LAN devices may
be restricted in some situations or environments for
example:
·On board of airplanes, or
·In an explosive environment, or
·In case the interference risk to other devices or services
is perceived or identified as harmful
In case the policy regarding the use of Wireless LAN
devices in specific organizations or environments (e.g.
airports, hospitals, chemical/oil/gas industrial plants,
private buildings etc.) is not clear, please ask for
authorization to use these devices prior to operating the
equipment.
Regulatory Information/disclaimers
Installation and use of this Wireless LAN device must be in
strict accordance with the instructions included in the user
documentation provided with the product. Any changes or
modifications made to this device that are not expressly
approved by the manufacturer may void the user’s
authority to operate the equipment. The Manufacturer is
not responsible for any radio or television interference
caused by unauthorized modification of this device, of the
substitution or attachment. Manufacturer and its
authorized resellers or distributors will assume no liability
for any damage or violation of government regulations
arising from failing to comply with these guidelines.
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. End users
must follow the specific operating instructions for satisfying
RF exposure compliance. To maintain compliance with
FCC RF exposure compliance requirements, please follow
operation instruction as documented in this manual.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
SAR compliance has been established in typical laptop
computer(s) with CardBus slot, and product could be used
in typical laptop computer with CardBus slot. Other
application like handheld PC or similar device has not
been verified and may not compliance with related RF
exposure rule and such use shall be prohibited.
The availability of some specific channels and/or
operational frequency bands are country dependent and
are firmware programmed at the factory to match the
intended destination. The firmware setting is not
accessible by the end user.
Europe EU Declaration of Conformity
This device complies with the essential requirements of
the R&TTE Directive 1999/5/EC. The following test
methods have been applied in order to prove presumption
of conformity with the essential requirements of the
R&TTE Directive 1999/5/EC:
EN 60 950-1: 2001 +A11: 2004
Safety of Information Technology Equipment
EN 50392: 2004
Generic standard to demonstrate the compliance of
electronic and electrical apparatus with the basic
restrictions related to human exposure to electromagnetic
fields (0 Hz - 300 GHz)
EN 300 328 V1.6.1 (2004-11)
Electromagnetic compatibility and Radio spectrum Matters
(ERM); Wideband transmission systems; Data
transmission equipment operating in the 2,4 GHz ISM
band and using wide band modulation techniques;
Harmonized EN covering essential requirements under
article 3.2 of the R&TTE Directive
EN 301 489-17 V1.6.1 (2005-08) and EN 301 489-1
V1.4.1 (2002-08)
Electromagnetic compatibility and Radio spectrum Matters
(ERM); ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 17: Specific conditions
for 2,4 GHz wideband transmission systems and 5 GHz
high performance RLAN equipment
This device is a 2.4 GHz wideband transmission system
(transceiver), intended for use in all EU member states
and EFTA countries, except in France and Italy where
restrictive use applies.
In Italy the end-user should apply for a license at the
national spectrum authorities in order to obtain
authorization to use the device for setting up outdoor radio
links and/or for supplying public access to
telecommunications and/or network services.
This device may not be used for setting up outdoor radio
links in France and in some areas the RF output power
may be limited to 10 mW EIRP in the frequency range of
2454 2483.5 MHz. For detailed information the end-user
should contact the national spectrum authority in France.
0560
Česky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede [fabrikantens navn] erklæ rer herved, at lgende udstyr [udstyrets
typebetegnelse] overholder de sentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Ü bereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
esolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp =
type of equipment] vastavust direktiivi 1999/5/EÜ hinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΣΗΝ ΠΑΡΟΤ΢Α [name of manufacturer] ΔΗΛΩΝΕΙ ΟΣΙ [type of equipment]
΢ΤΜΜΟΡΦΩΝΕΣΑΙ ΠΡΟ΢ ΣΙ΢ ΟΤ΢ΙΩΔΕΙ΢ ΑΠΑΙΣΗ΢ΕΙ΢ ΚΑΙ ΣΙ΢ ΛΟΙΠΕ΢ ΢ΥΕΣΙΚΕ΢
ΔΙΑΣΑΞΕΙ΢ ΣΗ΢ ΟΔΗΓΙΑ΢ 1999/5/ΕΚ.
Français
[French]
Par la présente [nom du fabricant] clare que l'appareil [type d'appareil] est conforme
aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Latviski
[Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment
/ iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.
Lietuvių
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius
[Lithuanian]
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van
richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-
ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... pus] megfelel a vonatkozó alapvetõ
vetelményeknek és az 1999/5/EC irányelv egyéb elõísainak.
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy
1999/5/EC.
Português
[Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a
všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
[Valmistaja = manufacturer] vakuuttaa ten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
rmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de
sentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Export restrictions
This product or software contains encryption code that
may not be exported or transferred from the US of Canada
without an approved US Department of Commerce export
license.
Safety Information
Your device contains a low power transmitter. When
device is transmitted it sends out radio frequency (RF)
signal.
CAUTION: To maintain compliance with FCC’s RF
exposure guidelines, this equipment should be installed
and operated with minimum distance 20cm between the
radiator and your body. Use on the supplied antenna.
Unauthorized antenna, modification, or attachments could
damage the transmitter and may violate FCC regulations.
The antenna(s) used for this transmitter must be installed
to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
CE Mark Warning
This is a Class B product. In a domestic environment, this
product may cause radio interference, in which case the
user may be required to take adequate measures.
Protection requirements for health and safety
Article 3.1a
Testing for electric safety according to EN 60950 has been
conducted. These are considered relevant and sufficient.
Protection requirements for electromagnetic
compatibility Article 3.1b
Testing for electromagnetic compatibility according to EN
301 489-1, EN 301 489-17 and EN 55024 has been
conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum Article 3.2
Testing for radio test suites according to EN 300 328-2
has been conducted. These are considered relevant and
sufficient.
CE in which Countries where the product may
be used freely:
Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal,
Greece, Ireland, Denmark, Luxembourg, Austria, Finland,
Sweden, Norway and Iceland.
France: except the channel 10 through 13, law prohibits
the use of other channels.
TABLE OF CONTENT
Introduction………………………………………….1
Overview of this User’s Guide………………….……….1
Unpacking and Setup………………………………3
Unpacking………………………………………………...3
Setup………………………………………………………3
Hardware Installation………………………………4
LED Indicator for CardBus…………………………..4
LED Indicator for PCI……………………………………4
Check the installation…………………………………..4
Software Installation……………………………….5
Windows Driver Installation…………………………….5
Windows Vista/7 Wireless Utility Setting……………..7
Technical Specifications…………………………15
INTRODUCTION
Congratulations on your purchase of this 300Mbps N_Max
Wireless PCI Card.
This manual contains detailed instructions regarding the
operation of this product. Please keep this manual for
future reference.
With the 300Mbps N_Max Wireless PCI Card, a desktop
or laptop computer can communicate with another
computer wirelessly. An easy-to-use utility is bundled with
the 300Mbps N_Max Wireless PCI Card for configuration,
monitoring, and diagnostic purposes.
The 300Mbps N_Max Wireless PCI Card can wirelessly
transmit and receive data, at a speed of up to 300
megabits per second.
The 300Mbps N_Max Wireless PCI Card provides users
with access to real-time information anywhere in their
organization. The mobility of the 300Mbps N_Max
Wireless PCI Card provides productivity and service,
which are not available under wired networks. The
300Mbps N_Max Wireless PCI Card can easily adapt from
peer-to-peer networks, suitable for a small number of
users, to full infrastructure networks of thousands of users
that allow roaming around a broad area.
Overview of this User’s Guide
Introduction. Describes the 300Mbps N_Max Wireless
PCI Card and its features.
Unpacking and Setup. Helps you get started with the
basic installation of the 300Mbps N_Max Wireless PCI
Card.
Hardware Installation. Describes the LED indicator on
the Adapter.
Software Installation. Describes how to setup the driver
and the utility setting.
Technical Specifications. Lists the technical (general,
physical and environmental) specifications of the 300Mbps
N_Max Wireless PCI Card.
UNPACKING AND SETUP
This section provides unpacking and setup information for
the 300Mbps N_Max Wireless PCI Card.
Unpacking
The box should contain the following items:
One WNC-0610 300Mbps N_Max Wireless PCI Card
One Driver & Utility CD-ROM
One QIG
If any item is found missing or damaged, please contact
your local reseller for replacement.
Setup
Before installation, check the following:
Make sure your computer is running at least a 300MHz
or above processor with 256MB RAM or above
Visually inspect the CardBus/PCI Adapter and make
sure that it is fully plugged in to the CardBus/PCI slot.
The operating system on your computer must be the
following: Windows 2000/XP/Vista/7
A 802.11n or 802.11b/g access point.
Make sure the environment has minimal interference
and obstructions.
4
HARDWARE INSTALLATION
LED Indicator for CardBus
Link
The Link LED indicator lighted green when the 300Mbps
N_Max Wireless PCI Card is connected to wireless
network successfully.
ACT (Activity)
The ACT LED indicator blinking green when the 300Mbps
N_Max Wireless PCI Card is transmitting or receiving data.
LED Indicator for PCI
Link
The Link LED indicator lighted green when the 300Mbps
802.11g Wireless LAN Adapter is connected to wireless
network successfully.
Check the installation
The LEDs of the Wireless LAN Adapter are clearly visible
and the status of the network link can be seen instantly:
1. Once the device is plugged to the station’s
CardBus/PCI slot, the LED of the Wireless LAN Adapter
will light up indicating a normal status.
2. When the device plugged to the station’s CardBus/PCI
slot and the driver was installed, the ACT will start
alternate blinking, it means that the device is starting to
scan the wireless devices near the Wireless LAN
Adapter.
3. While the Wireless LAN Adapter linked up and
transmitting data to the Access Point or to other
Wireless LAN station, the Link LED will lighted green.
5
SOFTWARE INSTALLATION
This section describes how to install the driver and utility
for the 300Mbps N_Max Wireless PCI Card.
Important note:
After you finished the installation of Win7 default
driver, please install LevelOne utility/driver additional
to let WNC-0610 works well.
Note: DO NOT install the 300Mbps 802.11g Wireless LAN
Adapter in the computer until instructed to do so.
Windows 98/ME/2000/XP/Vista/7 Utility and Driver
Installation
1) Insert the 300Mbps N_Max Wireless PCI Card Driver &
Utility CD-ROM and the Auto-run program will appear.
Alternatively, open a file browser and double click on
the autorun.exe file located in the CD directory. In
some specific setting on Windows system, you may
need to proceed the software manually, go to your
Windows Start menu and choose Run, type
“D:\Utility\Setup.exe” and click OK.
Note: (D:\ will depends on where the CD-ROM drive
is located and <Windows OS> will depend on the
Windows OS you are using)
2) If you need to install the driver manually, refer each
Windows OS to the following CD-Rom directory path:
D:\Driver\<Windows OS>.
Note: (D:\ will depends on where the CD-ROM drive
is located and <Windows OS> will depend on the
Windows OS you are using).
6
3) Click “Install Software (Utility)” to install the driver and
software. Select Windows XP / 2K / Vista” or
“Windows7” , depending on your operating system,
and the install wizard will begin installing the software.
Follow the install wizard instructions to complete the
installation.
4) Follow the Install Shield Wizard Instructions. Click
Next to continue and finish it.
The installation program will help you to setup the
Wireless LAN utility.
When the Wireless LAN Adapter was installed, you will
see the icon on the Windows task bar.
When the icon in the toolbar represents in full green color
then the signal strength has an excellent performance with
the AP, if it represents in yellow color then the signal
strength has a fair performance with the AP, and if the
7
icon represents no color, then the signal strength has a
worst performance with the wireless station.
Windows 2000/XP/Vista/7 Wireless Utility Setting
The user can configure the wireless settings using the
Wireless Adapter Configuration Utility. Double-click the
utility icon that appears in the taskbar.
8
Link Information
This is the default screen after launching the Utility
program.
Status: Shows the associated BSSID, which can be used
to identify the wireless access point.
SSID: Shows the current SSID, which must be the same
on the wireless client and AP in order for communication
to be established.
Wireless Mode: Shows the current wireless mode used
for wireless communication.
Encryption: Shows the current encryption mode used on
the wireless network.
TxRate: Shows the current data rate used for transmitting.
Channel: Shows the current channel for communication.
9
Signal Strength of Percentage: Shows the wireless
signal strength of the connection between the Wireless
LAN Adapter with the Access Point.
Tx/Rx: Shows the statistics of data transfer, and the
calculation is based on the number of packets transmitted
and received. It also shows the link quality of the Wireless
LAN Adapter with the Access Point when operating under
Infrastructure mode.
Configuration
This screen is where you set the basic wireless settings
for the Wireless LAN Adapter
SSID: Service Set Identifier, which is a unique name
shared among all clients in a wireless network. The SSID
must be identical for each client in the wireless network.
10
Wireless Mode: There are two modes available for
selection
Infrastructure to establish wireless communication
with the LAN and other wireless clients through the
use of Access Points.
Ad-Hoc to establish point-to-point wireless
communication directly with other wireless client
devices.
Authentication: The following options are available: Open
System, Shared Key, WPAPSK, WPA2-PSK, WPA EAP-
TLS, WPA2 EPA-TLS and WPA2-PSK. Select Open
System, Shared Key for WEP data encryption feature.
Open or Shared Key
Open System and Shared Key requires the user to set
a WEP key to exchange data with other wireless clients
that have the same WEP key.
Default Key: select one of the 4 keys to use.
Network Key: choose the encryption way, either in
HEX or ASCII formats, and enter the password in
the blank space.
Key Length: select 64 or 128 bits as the length of
the keys
Key Format: HEX or ASCII
11
WPA-PSK/WPA2-PSK
If WPA-PSK/WPA2-PSK is selected the below window
appears. Please enter a WPA Passphrase.
WPA-PSK/WPA2-PSK
If WPA/WPA2 is selected, configuration is enabled.
Please click the configuration” button. Select a
certification for drop down list.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

LevelOne WNC-0610 Manuale utente

Categoria
Schede di interfaccia / adattatori
Tipo
Manuale utente

in altre lingue