Tascam MD-350 Manuale del proprietario

Marca: Tascam

Modello: MD-350

Categoria: Lettori minidisc

Tipo: Manuale del proprietario

MD-350

Minidisc Deck

ESPAÑOL ITALIANO DEUTSCH FRANÇAIS ENGLISH

This appliance has a serial number located

on the rear panel. Please record the model

number and serial number and retain them

for your records.

Model number

Serial number

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

OWNER'S MANUAL / MANUEL DU PROPRIETAIRE

BEDIENUNGSANLEITUNG / MANUALE DI ISTRUZIONI

MANUAL DEL USUARIO / GEBRUIKSAANWIJZING

D00602210A

IMPORTANT SAFETY INSTRUCTIONS

– 2 –

CAUTION:

●Read all of these Instructions.

●Save these Instructions for later use.

●Follow all Warnings and Instructions marked on the audio

equipment.

1) Read Instructions — All the safety and operating instructions should

be read before the product is operated.

2) Retain Instructions — The safety and operating instructions

should be retained for future reference.

3) Heed Warnings — All warnings on the product and in the operating

instructions should be adhered to.

4) Follow Instructions — All operating and use instructions should be

followed.

5) Cleaning — Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

6) Attachments — Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

7) Water and Moisture — Do not use this product near water

for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a

wet basement; or near a swimming pool; and the like.

8) Accessories — Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall, causing serious

injury to a child or adult, and serious damage to the product. Use only

with a cart, stand, tripod, bracket, or table recommended by the

manufacturer, or sold with the product. Any mounting of the product

should follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9) A product and cart combination should be moved with care. Quick

stops, excessive force, and uneven surfaces may cause the product

and cart combination to overturn.

10) Ventilation — Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not be blocked or

covered. The openings should never be blocked by placing the product

on a bed, sofa, rug, or other similar surface. This product should not be

placed in a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instructions have

been adhered to.

11) Power Sources — This product should be operated only from the

type of power source indicated on the marking label. If you are not sure

of the type of power supply to your home, consult your product dealer

or local power company. For products intended to operate from battery

power, or other sources, refer to the operating instructions.

12) Grounding or Polarization — This product may be equipped with

a polarized alternating-current line plug (a plug having one blade wider

than the other). This plug will fit into the power outlet only one way.

This is a safety feature. If you are unable to insert the plug fully

into the outlet, try reversing the plug. If the plug should still fail to fit,

contact your electrician to replace your obsolete outlet. Do not defeat

the safety purpose of the polarized plug.

13) Power-Cord Protection — Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords at plugs,

conve-nience receptacles, and the point where they exit from the

product.

14) Outdoor Antenna Grounding — If an outside antenna or cable

system is connected to the product, be sure the antenna or cable

system is grounded so as to provide some protection against voltage

surges and built-up static charges. Article 810 of the National

Electrical Code, ANSI/NFPA 70, provides information with regard to

proper grounding of the mast and supporting structure, grounding of

the lead-in wire to an antenna discharge unit, size of grounding

conductors, location of antenna-discharge unit, connection to

grounding electrodes, and re-quirements for the grounding electrode.

"Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention

to Section 820-40 of the NEC which provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point

of cable entry as practical.

grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point

of cable entry as practical.

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

NEC - NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

Example of Antenna Grounding as per

National Electrical Code, ANSI/NFPA 70

GROUND

CLAMP

15) Lightning — For added protection for this product during a

lightning storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet and disconnect the

antenna or cable system. This will prevent damage to the product due

to lightning and power-line surges.

16) Power Lines — An outside antenna system should not be located

in the vicinity of overhead power lines or other electric light or power

circuits, or where it can fall into such power lines or circuits. When

installing an outside antenna system, extreme care should be taken to

keep from touching such power lines or circuits as contact with them

might be fatal.

17) Overloading — Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in risk of fire or

electric shock.

18) Object and Liquid Entry — Never push objects of any kind into

this product through openings as they may touch dangerous voltage

points or short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19) Servicing — Do not attempt to service this product yourself as

opening or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service personnel.

20) Damage Requiring Service — Unplug this product from the wall

outlet and refer servicing to qualified service personnel under the

following conditions:

a) when the power-supply cord or plug is damaged.

b) if liquid has been spilled, or objects have fallen into the product.

c) if the product has been exposed to rain or water.

d) if the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operating instructions as an improper adjustment of other controls may

result in damage and will often require extensive work by a qualified

technician to restore the product to its normal operation.

e) if the product has been dropped or damaged in any way.

f ) when the product exhibits a distinct change in performance

this

indicates a need for service.

21) Replacement Parts — When replacement parts are required, be

sure the service technician has used replacement parts specified by

the manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other

hazards.

22) Safety Check — Upon completion of any service or repairs to this

product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

23) Wall or Ceiling Mounting — The product should be mounted to a

wall or ceiling only as recommended by the manufacturer.

24) Heat — The product should be situated away from heat sources

such as radiators, heat registers, stoves, or other products (including

amplifiers) that produce heat.

SAFETY INFORMATION

– 3 –

This product has been designed and manufactured according to FDA regulations "title 21, CFR, chapter 1, subchapter J, based on the Radiation

Control for Health and Safety Act of 1968", and is classified as class 1 laser product. There is no hazardous invisible laser radiation during

operation because invisible laser radiation emitted inside of this product is completely confined in the protective housings.

The label required in this reguration is shown 1.

… CAUTION

- DO NOT REMOVE THE PROTECTIVE HOUSING USING SCREWDRIVER.

- USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

- IF THIS PRODUCT DEVELOPS TROUBLE, MAKE A CONTACT WITH OUR SERVICEMAN, AND DO NOT USE THE PRODUCT IN A

TROUBLED STATE.

CERTIFICATION

THIS PRODUCT COMPLES WITH DHHS

RULES 21 CFR SUBCHAPTER J APPLI-

CABLE AT DATE OF MANUFACTURE

TEAC CORPORATION

3-7-3 NAKA-CHO, MUSASHINO-SHI, TOKYO, JAPAN

MANUFACTURED TIF

Optical pickup: Type : KMS-260A

Manufacturer : SONY Corporation

Laser output : 4.55 mW

Wavelength : 785±20 nm

For U.S.A.

TO THE USER

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user

is encouraged to try to correct the interference

by one or more of the following measures.

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the

equipment and receiver.

c) Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

d) Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

Changes or modifications to this equipment

not expressly approved by TEAC

CORPORATION for compliance could void the

user’s authority to operate this equipment.

For U.S.A

Before UseContents

… Place the unit on a hard flat surface.

… Avoid placing it in direct sunlight or

close to a source of heat. Also avoid

locations subject to vibrations and

excessive dust, heat, cold or moisture.

… Do not open the cabinet, as this might

result in circuitry damage or electrical

shock.

… Do not attempt to clean the unit with

chemical solvents, as this might

damage the finish. Use a clean, dry

cloth.

… When removing the power plug from the

wall outlet, always pull directly on the

plug, never yank the cord.

… Keep this manual in a safe place for

future reference.

IMPORTANT SAFETY INSTRUCTIONS ................................................................ 2-3

Before Use ................................................................................................................ 4

Read This Before Operating .............................................................................. 4

Handling MDs .............................................................................................. 5

Memory back-up function........................................................................... 5

When "Protected !!" is displayed................................................................ 5

While "UTOC Writing" is blinking............................................................... 5

When "D-IN UNLOCK !" blinks.................................................................... 5

Remote Control Unit........................................................................................... 5

Rack Mounting.................................................................................................... 6

Voltage Conversion (For general export models)............................................ 6

Connections .............................................................................................................. 6

Connection .................................................................................................. 6

Name of Each Control .............................................................................................. 7

Recording .................................................................................................................. 8

Recording an MD ............................................................................................... 8

Notes on Recording ........................................................................................... 9

Playback .................................................................................................................. 10

Normal Playback .............................................................................................. 10

Useful Tips for Recording ...................................................................................... 11

Monitoring the Input Signal ............................................................................ 11

Adjusting the Recording Level ....................................................................... 11

Assigning Track Numbers During Recording ................................................ 11

Recording Over Existing Tracks (Over Write) ................................................ 11

Sync Recording ................................................................................................ 12

Checking the Remaining MD Recording Time .............................................. 12

Checking the Recorded Tracks ....................................................................... 12

Timer Recording .............................................................................................. 12

Useful Tips for Playback ........................................................................................ 13

Using the Display Window ............................................................................. 13

Selecting the Desired Track ............................................................................. 13

Playing Tracks in Random Order (Shuffle Playback) .................................... 13

When Recording to Analog Tape .............................................................. 13-14

Playing Tracks in the Desired Order (Program Playback) ....................... 14-15

Repeating Track(s) (Repeat Playback) ............................................................ 15

Timer Playback ................................................................................................ 15

Pitch control ..................................................................................................... 15

Play modes ....................................................................................................... 15

Editing Recorded MDs ........................................................................................... 16

Notes on Editing .............................................................................................. 16

Erasing Track(s) (ERASE Function) ............................................................... 16

Dividing a Track (DIVIDE Function) ................................................................ 17

Combining Tracks (COMBINE Function) ........................................................ 17

Moving a Track (MOVE Function) .................................................................. 17

Assigning Titles (TITLE Function) ................................................................... 18

Assigning Titles to the Disc and All Tracks Successively

(TITLE AUTO INC Function)........................................................................ 18-19

Changing entered characters.................................................................... 19

Copying a Title (TITLE COPY Function) .......................................................... 19

Canceling the Last Operation (UNDO Function) ............................................ 19

Optional Functions.................................................................................................. 20

Correspondence between deck buttons and keyboard keys.................. 20

Editing keys ................................................................................................ 20

Title entry keys........................................................................................... 20

System Restrictions .......................................................................................... 20-21

Display Messages ................................................................................................... 21

Guide to the Serial Copy Management System .................................................. 22

Serial Copy Management System .................................................................. 22

Troubleshooting ..................................................................................................... 23

Specifications ......................................................................................................... 23

– 4 –

IMPORTANT (for U.K. Customers)

DO NOT cut off the mains plug from this

equipment. If the plug fitted is not

suitable for the power points in your

home or the cable is too short to reach

a power point, then obtain an

appropriate safety approved extension

lead or consult your dealer.

If nonetheless the mains plug is cut off,

remove the fuse and dispose of the plug

immediately, to avoid a possible shock

hazard by inadvertent connection to the

mains supply.

If this product is not provided with a

mains plug, or one has to be fitted,

then

follow the instructions given below:

IMPORTANT. DO NOT make any

connection to the larger terminal which

is marked with the letter E or by the

safety earth symbol ç or coloured

GREEN or GREEN-and-YELLOW.

The wires in the mains lead on this

product are coloured in accordance

with the following code:

BLUE: NEUTRAL

BROWN: LIVE

As these colours may not correspond

with the coloured markings identifying

the terminals in your plug proceed as

follows:

The wire which is coloured BLUE must

be connected to the terminal which is

marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN

must be connected to the terminal

which is marked with the letter L or

coloured RED.

When replacing the fuse only a

correctly rated approved type should

be used and be sure to re-fit the fuse

cover.

IF IN DOUBT — CONSULT A

COMPETENT ELECTRICIAN.

Read This Before Operating

ª Handling MDs

The MiniDisc (MD) measures 64 mm in

diameter. Although the MD is housed in a

protective cartridge (68 mm x 72 mm x 5

mm) and can be handled easily, deck

malfunc-tions may result if the cartridge

gets dust on it or is damaged. To protect

the disc, always take the following

precautions:

… Be sure that the MD is taken out of the

deck and put back in its MD case after

using it.

… Do not touch the disc inside the

cartridge. Do not open the shutter to

expose the MD.

… Do not place MDs in direct sunlight, high

temperatures, or high levels of humidity.

… Use a dry, soft cloth to clean the

cartridge.

… When attaching a label to the MD

cartridge, be sure to apply it correctly to

the specified position. If the label is

rolled up or partially detached, the MD

cartridge may get stuck inside the deck.

… Do not place one label on top of another.

ª Memory back-up function

This unit is provided with a memory back-

up function. When you use the deck for the

first time, leave it on for about 5 minutes to

allow the back-up circuit to be charged

and become operational. When not using

the deck for a while, try to turn the power

on every 3 or 4 days.

ª Serial Copy Management System

This deck complies with the SCMS (Serial

Copy Management System). As a result, it

is not possible to digitally record from a

source MD which has been recorded

digitally.

Cartridge

Shutter

ª When "Protected !!" is

displayed

… A playback-only MD is loaded.

… The MD is record-protected against

accidental erasure. To make recording

(or editing) possible, slide the record-

protect tab to close the hole.

ª While "UTOC Writing" is

blinking:

"UTOC Writing" blinks while the MD is

being ejected after recording (or

editing). While it is blinking, the recorded

data is being written on the MD. Do not

pull out the power cord or vibrate the

deck. Otherwise the recorded data may

not be written correctly on the MD.

If the power is turned off with the MD

left in the deck (" " lights up)

after recording, the UTOC cannot be

recorded. Turn the power back on

within 3 or 4 days and eject the MD. The

recorded data might be lost if the MD is

left in the deck for a long time.

ª When "D-IN UNLOCK !" blinks

… The program source is not connected to

the [DIGITAL INPUT 1] or [DIGITAL IN 2]

terminal even though you have selected

[DIGITAL 1] or [DIGITAL 2] with the

[INPUT SELECTOR]. Either make the

digital connection or select [ANALOG]

with the [INPUT SELECTOR] and perform

analog recording.

… This message also appears when the

digital signal input is interrupted during

digital recording. To continue recording,

restart the digital program source.

– 5 –

When operating the remote control unit,

point it towards the remote sensor on the

front panel of the unit.

ª Battery installation

1. Remove the battery compartment

cover.

2. Insert two "AA" (R6, SUM-3) dry

batteries.

Make sure that the batteries are

inserted with their positive ± and

negative — poles positioned correctly.

3. Close the cover until it clicks.

Battery replacement

If you notice that the distance between

the remote control unit and the player for

correct operation becomes shorter, it

indicates that the batteries are exhaust-

ed. In this case replace the batteries with

new ones.

Precautions concerning batteries

… Be sure to insert the batteries with

correct positive ± and negative —

polarities.

… Use batteries of the same type. Never

use different types of batteries

together.

… Rechargeable and non-rechargeable

batteries can be used. Refer to the

precautions on their labels.

… When the remote control unit is not to

be used for a long time (more than a

month), remove the batteries from the

remote control unit to prevent them from

leaking. If they leak, wipe away the

liquid inside the battery compartment

and replace the batteries with new

ones.

… Do not heat or disassemble batteries

and never dispose of old batteries by

throwing them in fire.

Remote Control Unit

ENGLISH

– 6 –

Connections

… Turn off power for all equipment before

making connections.

… Read instructions of each component

you intend to use with the MD deck.

ª Connection

ANALOG INPUT/OUTPUT

(BALANCED/UNBALANCED) terminals

Use these terminals to connect the deck to

a mixer, cassette tape recorder or other

components.

… Be sure to insert each plug securely. To

prevent hum and noise, do not bundle

the connection cords with the power

cord or speaker cord.

ª Power cord

Be sure to connect the power cord to an

AC outlet which supplies the correct

voltage.

… Hold the power plug when plugging or

unplugging the power cord.

Rack Mounting

Install this deck with the provided

mounting screw kit as illustrated.

DIGITAL INPUT 1/OUTPUT terminals

Use these terminals to connect the deck to

a digital component (such as a CD player,

DAT deck, digital amplifier, or another MD

deck).

… Use a digital optical (TOS) cable

(optional) for digital recording. Connect

the [DIGITAL IN 2] terminal located on

the front panel to a digital component

such as a DAT/MD deck.

… When making a digital connection,

remove the caps from the terminals.

When the terminals are not in use, leave

the caps in place.

Be sure to remove the power cord from the

AC outlet before repositioning the voltage

converter switch.

1. Locate the voltage selector on the rear

panel.

2. Using a flat-bladed screwdriver, set to

the appropriate 230 V or 120 V position

according to your area.

Voltage Conversion

(For general export models)

IN NORTH AMERICA DANSL'AMERIQUE

USE ONLY ON 120 V DU NORD:

SUPPLY. UTILISABLE SUR 120 V

D'ALIMENTATION

UNIQUEMENT.

– 7 –

ENGLISH

Name of Each Control

1 [POWER] button

2 [TIMER PLAY/OFF/REC] switch

3 PITCH CONTROL ON/OFF switch

4 [INPUT] control

5 Remote sensor

6 Disc insertion slot

7 [

ø EJECT] button

8 [

º RECORD] button

9 [DISPLAY] button

0 [

∆ SEARCH˚] buttons

q [PLAY MODE] button

w [

µ TRACK≤] dial / [PUSH ENTER]

e [EDIT/NO] button

r [YES] button

t [INPUT SELECTOR] switch

y [PHONES] jack

u PHONES level control

i Display window

o [

ª STOP] button

p [

¥ PLAY] button

a [

π READY] button

s [DIGITAL IN 2] terminal

d [KEYBOARD] terminal

f Numeric buttons (1 to 9, 0, +10)

g [REPEAT/A-B] buttons

h [TITLE EDIT] button

j [CLEAR] button

k [INSERT] button

l [DELETE] button

; [SYNC RECORD] button

z Upper/Lower case button [A

ß∑a]

x [AUTO SPACE] button

c [SCROLL] button

v Character select button [CHAR SELECT]

b [ENTER] button

n [

µ TRACK≤] buttons

– 8 –

Recording

1. Press the [POWER] button.

… "NO DISC" appears on the display.

… Turn on the source component and the

amplifier. Set the input selector to the

source component.

2. Insert a recordable MD.

… When a blank MD is inserted, the

display shows "Disc Loading", "TOC

Reading", "No Track !!" and "Blank Disc"

in sequence.

… When a partially recorded MD is

inserted, the deck will automatically

start recording from the end of the last

recorded track.

3. Select the input with the [INPUT

SELECTOR].

Display Selected Input

ANALOG ANALOG INPUT

DIGITAL 1 DIGITAL INPUT 1

(OPTICAL)

DIGITAL 2 DIGITAL IN 2 (OPTICAL)

(front panel)

4. Select the recording mode following the

steps below:

The MD-350 is capable of recording and

playing back in standard stereo mode

(SP), monaural standard speed (MON),

double long-play (LP2) and quadruple

long-play (LP4) modes.

Recording an MD

Insert in the direction of

the arrow.

Hold the MD with the

label side up.

As the name suggests, LP2 provides

long-play facilities giving twice the

usual recording/playback time, and LP4

provides four times the usual

recording/playback time.

All modes are stereo, except for MONO,

when recording will be performed using

only the left (L) channel. "L" appears on

the level meter, but the output is sent to

both channels.

To select a mode (SP, MON, LP2 or LP4)

for recording:

a) With the unit in stop mode, press the

[EDIT/NO] button repeatedly until “REC

MODE?” is displayed.

b) Press the [YES] button. ("RecMode>

XXX" is displayed.)

c) Use the [µTRACK≤] dial to select

the recording mode shown on the

display.

d) Press the [YES] button to confirm the

setting.

… Note:that when the time remaining on a

disc for further recording is shown, this

refers to the remaining time using the

current mode.

… It is possible to include tracks recorded

in different modes (SP,MONO, LP2 and

LP4) on one disc.

… Also note that while the LP4 (quadruple

long-play) mode provides exceptional

recording time thanks to advanced

compression technology, very

occasionally you may hear some slight

noise, depending on the material being

recorded. We therefore recommend that

if sound quality is more important for

your recording project than recording

time, you use either the SP (stereo) or

LP2 (double long-play) mode.

… The maximum amount of time available

with monaural recording is twice that of

stereo recording.

Buttons used on this page

ª Indication of recording mode

When the recording mode is shown, the

last three characters of the display are

used, and it is displayed as SP, MON, LP2

or LP4.

… In stop mode, the recording mode is

shown when the remaining time display

is selected.

… In record or record-ready mode, the

recording mode is always shown

… In play or in play-pause mode, the

recording mode is shown when the

remaining time is selected. In this case,

the display shows the recording mode

of the current material, not the

currently-selected recording mode.

5. Press the [

º RECORD] button.

… The deck enters the Record-Ready

mode ("

lights up).

… "Disc Full !!" or "Track Full !!" is

displayed when no room is available on

the MD for recording.

6. Adjust the recording level.

… If [ANALOG] was selected above,

adjust the recording level with the

[INPUT] control.

… When adjusting the recording level,

adjust so that the "OVER" segments of

the peak level meter do not light up.

7. Start recording.

Press the [

¥PLAY] button or the

[

π READY] button ( "¥

lights up).

Start playing the source program.

8. To stop recording, press the [

ª STOP]

button.

ª To stop recording temporarily (ready)

Press the [

π READY] button.

… Press the [

¥PLAY] or [π READY]

button to resume recording.

… Whenever you pause recording, the

track number increases by one.

ª To eject the MD

Press the [ø EJECT] button in stop mode.

If the power is turned off with the MD left

in the deck (" " lights up) after

recording, the UTOC cannot be recorded.

Turn the power back on within 3 or 4 days

and eject the MD. The recorded data

might be lost if the MD is left in the deck

for a long time.

Notes on Recording

ª To protect an MD against

accidental erasure

… After recording an MD, slide the record-

protect tab to open the hole.

… To record on the MD again, slide the tab

to close the hole.

ª When "Disc Full !!" or "Track

Full !!" is displayed

The MD has no more available space for

recording or the MD has used up all its

track numbers. Erase unnecessary tracks

or record music on another MD.

– 9 –

ENGLISH

ª The way track numbers are

assigned varies depending on

the source

When a CD or MD is played and recorded

digitally by selecting [DIGITAL 1/2] with

the [INPUT SELECTOR]:

… Track numbers on the recorded MD are

assigned to match those on the source

CD or MD. However, in the circum-

stances listed below only one track

number may be assigned to a recorded

section.

· A section composed of the repeated

playback of a single track on a disc

(e.g. using single track repeat

playback).

· A section composed of the succes-

sive recording of tracks with the

same track number from more than

one disc. Also, if the source is an

MD, track numbers may not be

marked for tracks shorter than 3

seconds.

When the source is recorded with

[ANALOG] or when a digital source other

than a CD or MD is recorded with

[DIGITAL 1] or [DIGITAL 2] while the Auto

Track function is OFF:

… The entire recording may be counted as

a single track with only one track

number assigned to it.

· Track numbers can be assigned

manually at the desired points by

pressing the [

º RECORD] button

during recording.

· Track numbers can be assigned

automatically by switching the Auto

Track function to "A_TRACK > ON"

before starting recording.

1. Press the [POWER] button.

… "NO DISC" appears on the display.

… Turn on the amplifier and set the input

selector to MD.

2. Insert an MD.

… After the TOC (Table Of Contents) data

has been read, the disc title (when the

disc has a title assigned to it), the total

number of tracks and the total playing

time of the disc are displayed.

Total number of tracks Disc title

Music calendar

Playback

Insert in the direction

of the arrow.

Hold the MD with the

label side up.

Normal Playback

… The disc or track title can be scrolled on

the display with the [SCROLL] button on

the remote control unit. After scrolling,

the title returns to its original display.

3. Start playback.

Press the [

¥PLAY] button ("¥" lights

up). Playback starts from the first track

and "001" appears on the "TRACK NO."

display.

… When the disc finishes playback, the

track numbers disappear from the music

calendar.

… If the total number of tracks exceeds 20

(" " lights up), the track number

should be confirmed on the TRACK NO.

display.

… Press the [

¥PLAY] button immediately

after recording is stopped (within 10

seconds) to play back a track which has

just been recorded from the beginning.

… If ten seconds or more have passed

after recording is stopped, or if the

[

¥PLAY] button is pressed after

pressing the [

ª STOP] button, playback

starts from the first track of the disc.

4. To stop playback, press the [

ª STOP]

button.

ª To stop playback temporarily (ready)

Press the [

π READY] button ("π" lights up).

… Press the [

¥PLAY] or [π READY] button

to resume playback.

ª To play a track located before or after

the current track

Turn the [

µ TRACK≤] dial.

… If you are operating the remote control

unit, select the desired track by pressing

the [

µ TRACK≤] buttons or entering

the track number with the numeric

buttons.

… The selected track number starts

playing.

ª To eject the MD

Press the [ø EJECT] button.

ª Headphones

When using headphones, connect the

headphone plug into the PHONES jack.

… Adjust the level of the signals output

from the phones jack.

Condensation

When the deck is moved directly from

a cold to a warm location or when the

temperature is raised suddenly in the

room where the deck is installed,

moisture may condense inside the

mechanism. This will prevent the deck

from operating normally and may result

in damage to the MD or to precision

parts. If condensation occurs, turn on

the deck and leave it for an hour or two

until the moisture evaporates.

Buttons used on this page

– 10 –

Useful Tips for Recording

– 11 –

You can monitor the input signal of the

component connected to each input

terminal before recording.

1. Press the [

ø EJECT] button to eject the

disc.

2. Select the input source with the [INPUT

SELECTOR].

3. Press the [

º RECORD] button.

("Monitor Mode" appears.)

… Even when the [REC MODE] is set to

[MONO], the output is sent to both

channels.

… Insert an MD or press the [

ª STOP]

button to cancel the Monitor mode.

ª Recording an analog signal

1. Insert a recordable MD and press the

[

º RECORD] button to enter the Record-

Ready mode (" " lights up).

2. Play the highest-level section of the

program source and turn the [INPUT]

control so that the "OVER" segments of

the peak level meters do not light.

3. Play the program source again.

… Press the [

¥PLAY] or [π READY] button

to start recording.

ª Recording a digital signal

1. In Record-Ready mode, press the

[EDIT/NO] button until “D-LEV 0.0dB”

appears.

2. Turn the [

µTRACK≤] dial to adjust

the recording level. The recording level

can be set in 0.5 dB steps within a range

between -6.0 dB and +6.0 dB.

3. Press the [YES] button after making the

adjustment.

Adjusting the Recording Level

Monitoring the Input Signal

Assigning track numbers at specific points

will make it easy to quickly locate those

points later using the playback or editing

functions.

ª To assign track numbers automatically

(Auto Track function)

Track numbers can be assigned automati-

cally during recording by setting the Auto

Track function to ON.

1. In the Record or Record-Ready mode,

press the [EDIT/NO] button until

"A_TRACK > XXX" appears.

2. Turn the [

µTRACK≤] dial to select

"A_TRACK > ON".

3. Press the [YES] button to end the setting

function.

… While the Auto Track function is "ON",

the signal level must remain low for 4 or

more seconds before a new track

number is advanced.

… During digital recording from a CD or

MD, the track numbers are advanced

automatically according to the CD or

MD data.

… Once the Auto Track function is "ON",

this mode will not be released even after

the power is turned off.

Press the [YES] button after selecting

"A_TRACK > OFF" to release it.

ª To assign track numbers manually

Press the [

º RECORD] button at every point

where you want to assign a track number

during recording. Each press of the button

advances the track number.

ª To assign track numbers after recording

A track number is added when a track is

divided in editing. (See "Dividing a track" on

page 16.)

Note:

Changing the input with the [INPUT

SELECTOR] switch during recording

activates the Record-Ready mode.

Assigning Track Numbers During

Recording

The Over Write function allows you to

record music by erasing a previously

recorded track.

1. Perform steps 1 to 4 of "Recording an

MD" on page 8.

2. Turn the [

µTRACK≤] dial (or press

the [

µTRACK≤] buttons on the

remote control unit) until the track

number to be recorded over appears.

3. Press the [

º RECORD] button (" "

lights up).

… After "Over Write" appears, the remain-

ing recording time is displayed.

… The track numbers which come after the

track being recorded over blink on the

music calendar.

4. Adjust the recording level.

… If [ANALOG] was selected above, adjust

the recording level with the [INPUT]

control.

5. Press the [

¥PLAY] button or [π READY]

button to start recording.

… The deck records over the existing

track. The track number is updated.

ª Recording over an existing track from

the middle

1. Select the track number to be erased

then press the [

¥PLAY] button to start

playback.

2. Press the [

π READY] button where you

want to start recording.

3. Press the [

º RECORD] button.

… The track number is updated and blinks

on the music calender.

4. Press the [

¥PLAY] or [π READY] button

to start recording.

… The deck records over the existing

track.

[CAUTION]

… It is not possible to record from the

middle of an existing track when

" " or " " is lit.

Recording Over Existing Tracks

(Over Write)

Buttons used on this page

ENGLISH

– 12 –

The deck starts recording when the input

audio exceeds a certain level and pauses

when the input audio has dropped below a

certain level continuously for 4 seconds or

more.

1. Perform steps 1-4 of "Recording an MD"

on page 8.

2. Press the [SYNC RECORD] button on the

remote control unit. The deck enters the

Sync Record-Ready mode.

(" " and " " light up.)

… The remaining recording time appears

after "S_SYNC ON" is displayed.

3. Start playing the source component.

… The deck starts sync recording upon

detection of the input audio signal.

It pauses when the input audio level

drops below a certain level.

… You cannot start recording manually

by pressing the [

¥ PLAY] button or

[

π READY] button in the Sync Record-

Ready mode.

… Press the [SYNC RECORD] button again

to cancel sync recording.

Notes:

… Pressing the [

π READY] button during

sync recording aborts the Sync Record

operation.

… Changing the input with the [INPUT

SELECTOR] switch during sync

recording aborts the Sync Record

operation.

Sync Recording

With each press of the [DISPLAY] button,

the display changes as follows:

In the Stop /Record mode:

… The remaining recording time (REMAIN)

is only displayed in the Record-Ready

mode.

… The disc title can be displayed only

when it has been recorded onto the MD.

ª Press the [¥PLAY] button immediately

after stopping recording.

The track which has just been recorded

will be played from the beginning.

∑∑

ª To play from the first track of the MD

after recording:

Press the [

ª STOP] button again

immediately after stopping recording then

press the [

¥PLAY] button.

∑∑∑

PLAY

STOP

Recording

PLAY

STOP

Recording

Checking the Recorded Tracks

Checking the Remaining MD

Recording Time

By connecting this deck with a timer

(commercially available), you can start and

stop recording operations at a preset time.

1. Perform steps 1 to 6 of "Recording an

MD" on page 8.

2. Set the [TIMER] switch to [REC].

3. Set the [TIMER] so that it starts and

stops power supply at the desired start

time and end time.

… As the actual recording starts after the

"TOC Reading" operation, set the timer

recording start time to slightly before

the time when you want to start

recording.

… Each component power is turned off.

… When the start time comes, power is

supplied to the components and

recording starts.

[CAUTION]

… When timer recording is performed in

the "SHUFFLE" mode or "PROGRAM"

mode, the deck automatically enters the

"CONTINUE" mode.

… Be sure to turn the deck on again and

eject the MD within 3 or 4 days of timer

recording. When the MD is ejected, the

recorded contents will be written on the

MD. If the deck is left off for a long time

after the timer recording has finished,

the contents may disappear.

… During timer recording, recording starts

from the end of the previously-recorded

portion on the MD.

… Set the [TIMER] switch to [OFF] after

timer recording. If the timer is left in

[REC], the deck will automatically start

recording the next time the power is

turned on.

Timer Recording

Buttons used on this page

Useful Tips for Recording

ENGLISH

Useful Tips for Playback

1. In the Stop mode, press the [PLAY

MODE] button repeatedly until "SHUFFLE

MODE" is displayed (" " lights

up).

2. Press the [

¥PLAY] button.

… To play the next track, turn the

[

µ TRACK≤] dial clockwise (or press

the [

≤] button on the remote control

unit) during shuffle playback.

… To play from the beginning of the

current track, turn the [

µ TRACK≤]

dial counterclockwise (or press the

[

µ ] button on the remote control unit)

during shuffle playback.

… The Shuffle mode will not be canceled

even when the power is turned off.

… To cancel the Shuffle mode, press the

[PLAY MODE] button repeatedly until

"CONTINUE MODE" is displayed.

ª Playing a track by direct search

Specify the desired track by pressing the

numeric buttons (1 to 9, 0, +10) on the

remote control unit. The specified track

starts to play.

… Examples of operation for direct search

of track number 10 or more:

To search track number 10:

Press +10 once then 0.

To search track number 25:

Press +10 twice then 5.

… Press the [CLEAR] button while "TRACK

NO." is blinking to cancel it.

ª To skip to the previous or next track

Turn the [

µ TRACK≤] dial clockwise

or counterclockwise (or press the

[

µ TRACK≤] buttons on the remote

control unit) during playback to skip to a

track located after or before the current

track.

ª To search a desired section

During playback, press and hold the

[

∆/˚] (or [∆ SEARCH˚]) buttons to

search the desired section.

… In the Play-Ready mode, the desired

section can be searched by observing

the elapsed playing time or remaining

playing time on the display.

… Normal search may not be possible if

there are several successive short

tracks of only a few seconds in length.

Selecting the Desired Track

– 13 –

The information shown on the display

allows you to check the disc title, track

title, the total track number in an MD, total

playing time, remaining recordable time of

the MD.

… Each press of the [DISPLAY] button

changes the display as shown below.

In the Stop mode:

In the Play mode:

… The total number of tracks appears on

the TRACK NO. display.

… The disc title and track titles are

displayed only when they have been

recorded onto the MD.

… When a track has been selected in the

Stop mode ("TRACK" is lit), pressing the

[DISPLAY] button displays the track title.

… When a track title is composed of more

than 100 characters, the 100th character

and beyond cannot be displayed.

… The disc or track title can be scrolled on

the display with the [SCROLL] button on

the remote control unit. After scrolling,

the title returns to its original display.

Using the Display Window

Buttons used on this page

Each track on the disc is played once in

random order.

Playing Tracks in Random Order

(Shuffle Playback)

ª To play tracks with spaces inserted

after every track (Auto Space playback)

The Auto Space playback function inserts

a 3-second blank space between each

track. This makes possible music scan

operations when recording from MDs to

analog tape.

1. Press the [AUTO SPACE] button on the

remote control unit once so that

"A_SPACE ON" is displayed. ("

" lights up.)

2. Press the [

¥PLAY] button.

… To release Auto Space Playback, press

the [AUTO SPACE] button repeatedly

until " " disappears.

ª To pause after each track

(Auto Ready playback)

The deck can enter the Ready mode after

playing each track. This feature is

convenient when copying a single MD

track onto tape or when the tracks to be

copied are not continuous.

1. Press the [AUTO SPACE] button on the

remote control unit twice so that

"A_READY ON" is displayed.

(" " lights up.)

When Recording to Analog Tape

Each press clears the current last track

in the program.

3. Press the [

¥PLAY] button to start

Program playback.

… The program is held in memory after

Program playback has been stopped by

pressing the [

ª STOP] button or it has

stopped automatically at the end.

… Pressing the [

ª STOP] button in the Stop

mode clears the program memory.

… When the total program playback time is

longer than 159 minutes and 59 seconds,

"---m--s" appears on the time counter.

… When the 25th track has been

programmed, "PGM Full !!" is displayed

and no more tracks can be programmed.

… Pressing the [PLAY MODE] button in the

Stop mode cancels the Program Play

mode and clears the program memory.

… The Program mode will not be canceled

even when the power is turned off, and

the programmed data will remain in the

deck.

… If you attempt program playback when

no programmed data is entered, normal

playback will start after "PGM Empty !!"

is displayed.

ª To check the program contents

In the Play or Play-Ready mode, turn the

[

µTRACK≤] dial or press the [µ ] or

[

≤] button on the remote control unit to

display the program contents.

ª To delete a programmed track

In the Stop mode, press the [CLEAR] button.

Each press clears the current last track in

the program.

– 14 –

2. Press the [¥PLAY] button.

… When playback is finished, the deck

pauses at the beginning of the next

track.

3. Press the [

¥PLAY] or [π READY] button

to start playing the next track.

… To release Auto Ready playback, press

the [AUTO SPACE] button repeatedly

until " " disappears.

… A

SPACE and A

READY playback cannot

be used together.

ª Auto cue mode

(tracks recorded in SP mode only)

The auto cue function lets the unit

automatically start playback at the audio

start of each track. The trigger level which

determines the point at which playback

starts is set as follows:

1 In stop, play or pause mode, press the

[EDIT/NO] button until “AUTO CUE?”

appears.

2 Press [YES].

3 Turn the [

µ TRACK≤ ] dial to

cycle the threshold level between the

following values: “-54dB”, “-60dB”,

“-66dB”, “-72dB” and “OFF”.

4 Press the [YES] button after making the

adjustment.

… When the Auto Cue mode is on (the

value is anything except “OFF”), and the

unit is in STOP, moving to the next or

previous track will automatically cue the

playback point to the first point in the

track where the sound level rises above

the trigger level as set above and the

unit will pause.

… When Auto Cue is on, and Auto Ready is

also on, moving to the next or previous

track will automatically cue the

playback point to the first point in the

track where the sound level rises above

the trigger level as set above and the

unit will pause at this point. If the

desired start of the track is cut off using

this function, the trigger level should be

adjusted to a lower level.

… Note that if Auto Cue and Auto Ready

are both off, moving to the next track

will enter stop mode as usual.

… If the Auto Cue mode is on, the Auto

Space function is unavailable.

Buttons used on this page

… If the Auto Space function is on when

Auto Cue is turned on, the Auto Space

function and the Auto Ready function (if

this is on) will be turned off.

… If the Auto Cue function is on, and the

[AUTO SPACE] button is pressed, the

only effect is to turn the Auto Ready

function on or off.

… The function does not work with tracks

recorded in any mode other than SP

mode. With any non-SP tracks, the cue

point is the top of the track, not the cue

point.

… This cue is made to ±1 frame accuracy

(in SP mode, this is ±64 ms).

Up to 25 tracks can be programmed in the

desired order and played.

ª To program tracks

1. In the Stop mode, press the [PLAY

MODE] button repeatedly until "PGM

MODE" appears in the display. After

"PGM MODE", the display shows "0m 00s

00p" (" " lights up).

2. Turn the [

µTRACK≤] dial so that the

desired track number indicator lights on

the music calendar, and press [PUSH

ENTER] on the dial.

… The track number blinks.

… Repeat this operation to program other

tracks.

… Tracks can be programmed

automatical-ly by simply pressing the

numeric buttons (1 to 9, 0, +10) on the

remote control unit to display their

numbers sequentially.

… When a track number of 21 or more is

selected, the " " indicator blinks.

However, the track number can still be

checked on the TRACK NO. display.

… The same track can be programmed

repeatedly.

… If you make a mistake in the track

number entry, press the [CLEAR] button.

Playing Tracks in the Desired

Order (Program Playback)

Useful Tips for Playback

ENGLISH

All or one of the tracks, or a specified

portion (A-B) of an MD can be played

repeatedly. Program playback and Shuffle

playback can also be repeated.

ª To repeat all MD tracks

(All-track repeat)

1. In the Stop mode, press the [PLAY

MODE] button to select one of the

following repeat play modes.

Play Mode Repeat

CONTINUE Normal repeat

SHUFFLE MODE Shuffle repeat

PGM MODE Program repeat

2. Press the [REPEAT] button on the

remote control unit once to display

"REPEAT ALL".

… " " lights up.

3. Press the [

¥PLAY] button.

The tracks will be played repeatedly in

the specified mode.

… To release REPEAT playback and

resume normal playback, press the

[REPEAT] button repeatedly until

"REPEAT OFF" appears.

… The Repeat Playback mode will not be

canceled even when the power is

turned off.

ª To repeat a single track

(Single-track repeat)

1. During playback in the "CONTINUE

MODE", press the [REPEAT] button on

the remote control unit twice.

Repeating Track(s)

(Repeat Playback)

… "REPEAT 1" appears (" " and

" " light up).

2. Press the [

¥PLAY] button. The current

track will be repeated.

3. The track to be repeated can be

changed by turning the [

µ TRACK≤]

dial or by pressing the [

µ TRACK≤]

buttons or numeric buttons (1 to 9, 0,

+10) on the remote control unit.

… Single-track repeat is unavailable in the

"SHUFFLE MODE" or "PGM MODE".

ª To repeat a section within a track

(A-B repeat)

A specified portion (between A and B) of a

track can be played repeatedly.

1. During playback, press the [A-B] button

on the remote control ("REPEAT A–" is

displayed, and " " lights up,

" " blinks) at the starting point (A) of

the portion you want to repeat.

2. Press the [A-B] button again ("REPEAT

A-B" is displayed, and " " and

" " light steadily) at the ending point

(B). The portion (A-B) will be played

repeatedly.

… A-B repeat playback of portions

extending over more than one track is

not possible during programmed

playback or shuffle playback.

… To cancel Repeat playback and resume

normal playback, press the [A-B] button

or [REPEAT] button again.

("REPEAT OFF" is displayed.)

… Press the [

ª STOP] button to erase the

specified portion (between A-B).

3. Set the timer to the desired start time

and turn off the power.

When the set time comes, each

component will be turned on and

playback will start.

… Set the [TIMER] switch back to [OFF]

after timer playback.

– 15 –

Buttons used on this page

ª To add a track to the program

In the Stop mode, turn the [

µTRACK≤]

dial to select the desired track number and

press [PUSH ENTER] on the dial.

A track can also be added from the remote

control unit by simply entering the track

number with the numeric buttons

(1 to 9, 0, +10).

… The new track is appended to the end of

the existing program.

By connecting this deck with a timer

(commercially available), playback can be

started at a specified time.

1. Insert a pre-recorded MD and set the

[TIMER] switch to [PLAY].

2. Select the amplifier's input which

allows this deck to play back.

… Timer playback is available when

"SHUFFLE MODE", "PGM MODE", "ALL

REPEAT" or "REPEAT SINGLE" playback

is selected.

Timer Playback

You can use the pitch control feature to

play back material at ±12.0% relative to the

normal playback pitch. This feature is not

available in LP2 mode.

To set the pitch change which will be

operative when the PITCH ON/OFF switch

is on:

1 In stop, play or pause mode, press the

[EDIT/NO] button until "Pitch?" appears.

2 Press the [YES] button.

3 Turn the [

µ TRACK≤] dial to adjust

the pitch in 0.1% steps.

4 Press the [YES] button after making the

adjustment.

… The value set in this way does not take

effect until the PITCH ON/OFF switch is

set to ON.

… Note that when the position of the

PITCH ON/OFF switch is changed, the

sound is momentarily muted.

Pitch control

Tracks recorded in different modes (SP,

MONO, LP2 and LP4) can be combined on

one disc. When playing back a disc, the

appropriate mode is automatically

selected as each track is played back, and

this is shown on the display.

Play modes

Editing Recorded MDs

1. Specify the track to be erased with the

[

µTRACK≤] dial.

2. Press the [EDIT/NO] button repeatedly

until "ERASE TRK ?" is displayed.

3. Press the [YES] button.

("Track OK ?" is displayed.)

… Pressing the [EDIT/NO] button or the

[

ªSTOP] button while "Track OK ?" is

displayed aborts the operation.

4. Press the [YES] button again.

… "COMPLETE" is displayed. Once the

specified track has been erased, the

subsequent track is decreased by one

and all tracks following are renumbered.

… Repeat this procedure to erase

additional tracks.

ª To erase a part of a track

This operation consists of dividing the

track, erasing one of the tracks obtained

by division and combining the remaining

tracks. A part of a track can be erased

using these three functions.

(Example): To erase a part of A with track

number 1

– 16 –

Available editing operations include

erasing, moving, dividing and combining

tracks. It is also possible to assign disc and

track titles.

ª When "Protected !!" is displayed

The MD is record-protected against

accidental erasure. To make recording or

editing possible, slide the record-protect

tab to close the hole.

ª While "UTOC Writing" is blinking

This message indicates that the recorded

data is being written on the MD. Do not

pull out the power cord or vibrate the deck.

Otherwise the recorded data may not be

written correctly on the MD.

Notes on Editing

The data written on an MD can be erased

in the following ways.

… Erasing all tracks simultaneously

… Erasing a single track

… Erasing parts of a track

ª To erase all tracks at once (DISC

ERASE)

1. In the Stop mode, press the [EDIT/NO]

button repeatedly until "ERASE DISC ?" is

displayed.

2. Press the [YES] button.

("Sure ?" is displayed.)

… Pressing the [EDIT/NO] button or the

[

ªSTOP] button while "Sure ?" is

displayed aborts the operation.

3. Press the [YES] button again.

"COMPLETE" is displayed and then

"Blank Disc" is displayed to indicate that

all recorded data on the MD has been

erased.

… If "ERASE DISC ?" is selected with the

[EDIT/NO] button while "Blank Disc" is

displayed, and then the [YES] button is

pressed, UNDO (which cancels the

most recent operation) cannot be

performed.

ª To erase a single track (TRACK ERASE)

(Example): To erase B in track number 2

Erasing Track(s)

(ERASE Function)

Buttons used on this page

ENGLISH

A recorded track can be divided into two

tracks and a track number can be assigned

to the second track. This function is

designed for use when a single track

contains several musical pieces (for

example with an analog-recorded MD), or

when you want to mark a point for use in

track location.

(Example): To divide C and D contained in

track number 3 into two tracks

1. During playback, press the [

π READY]

button at the point where you want to

divide the current track into two.

2. Press the [EDIT/NO] button repeatedly

until "DIVIDE ?" is displayed.

3. Press the [YES] button.

… "Rehearsal" and "Point OK ?" are

displayed alternately while the first 4

seconds of the portion which becomes

the second track after division are

played repeatedly.

4. If the original track is not divided as

precisely as desired, you can fine-adjust

the division point by turning the

[

µTRACK≤] dial while monitoring

the sound.

… The division point can be adjusted

within an offset range of –128 ~ +127

(±1 corresponds to approx. 0.06 sec.).

… Press the [

ª STOP] button or [EDIT/NO]

button to abort the operation.

5. When the track is divided at the desired

point, press the [YES] button again.

… The track numbers of the new track

(second track after division) and

subsequent tracks are increased by one

but these new numbers are still

continuous.

… "COMPLETE" is displayed and the track

is divided. The deck will pause at the

beginning of new track obtained after

division.

tracks which have been recorded in

… Tracks obtained after division do not

have track titles, regardless of whether

the original track had one or not.

… The beginnings of tracks cannot be

divided.

Dividing a Track

(DIVIDE Function)

The order of tracks can be changed by

moving a track to another position. After

the track has been moved, track numbers

are automatically renumbered.

(Example): To move D from track number 4

to track number 2

1. During playback or pause, select the

track to be moved by turning the

[

µTRACK≤] dial.

2. Press the [EDIT/NO] button until

"MOVE ?" is displayed.

3. Press the [YES] button.

… "Move to 001?" is displayed. ("001"

blinks.)

Track number Destination track

to be moved number

4. Select the destination track number with

the [

µTRACK≤] dial.

… "Move to 002 ?" is displayed.

("002" blinks.)

… When you specify the destination track

number with the numeric buttons,

"COMPLETE" is displayed, then the track

is moved and the track numbers

are automatically changed. Playback

resumes from the track’s new location.

… Press the [

ª STOP] button or [EDIT/NO]

button to abort the operation.

5. Press the [YES] button again.

… "COMPLETE" is displayed, then the track

is moved and the track numbers

are automatically changed. Playback

resumes from the track’s new location.

Moving a Track (MOVE Function)

– 17 –

Two consecutive tracks can be combined

into a single track. This function is

designed for use when you want to play

several songs continuously or you want to

make a single track from many separately

recorded parts of music.

(Example): Combining B and C

1. Select a track number by turning the

[

µTRACK≤] dial.

… The selected track number will be

combined with the track before it.

For example, to combine track numbers

2 and 3, select track number 3 in this

step.

… If you select track 1, it will not be

combined into a single track.

2. Press the [EDIT/NO] button until

"COMBINE ?" is displayed.

3. Press the [YES] button.

… "Rehearsal" is displayed. The beginning

of the selected track is played back

repeatedly.

… If the combination point between the

two tracks is not played properly, press

the [EDIT/NO] button to stop playback

and restart the operation from the

beginning.

… Press the [

ª STOP] or [EDIT/NO] button

to abort the operation.

4. If the combination point is correct, press

the [YES] button again.

… "COMPLETE" is displayed for a few

seconds and the tracks are combined.

… When both tracks have titles assigned,

the title of the track before the selected

track is assigned to the combined

track. Subsequent track numbers are

decreased by one.

… Note that it is impossible to combine

tracks which have been recorded in

different modes (SP, MONO, LP2 and

LP4).

Combining Tracks

(COMBINE Function)

6. Select each character by turning the

[

µTRACK≤] dial and pressing

[PUSH ENTER] on the dial.

… If you are using the remote control unit,

select each character with the

[

µ TRACK≤] buttons and press the

[ENTER] button to enter it.

7. Repeat steps 5-6.

8. Press the [YES] button after assigning

the disc title.

… The title entry mode for track 1 is

automatically engaged ("001 > _" is

displayed) and the cursor blinks on the

display.

9. Repeat steps 5-6.

10. Press the [YES] button again.

… When the title entry mode for track 2 is

engaged ("002 > _" is displayed), repeat

steps 5-8.

… Repeat the character entry procedure

until all titles have been entered. The

disc title is then displayed if the deck is

in the Stop mode, or if the deck is in the

Play mode, the current track title is

displayed.

… Confirm titles by turning the

[

µTRACK≤] dial.

… Press the [

ª STOP] button to abort the

operation.

Press the [EDIT/NO] button for more

than 3 seconds (or press the [TITLE

EDIT] button on the remote control unit)

to cancel the title function and resume

playback.

Notes:

… Up to 100 characters can be entered per

track title. However, when the total

number of characters of all track titles

exceeds 1700, no more track titles can

be written onto the MD.

… If the TITLE AUTO INC function is

canceled before all titles have been

assigned, the track title currently being

entered will be erased. Only track titles

which have already been assigned will

be kept.

… If UNDO is performed after TITLE AUTO

INC is completed, the last edited track

title will be canceled.

… Disc and track titles can be assigned

during recording.

… If a track title is assigned while in the

Record-Ready mode during the

overwrit-ing of a track, the track title

will be erased when you resume

recording.

… "DISC" lights while a disc title is being

entered, and "TRACK" lights while a

track title is being entered.

… Assigning titles is unavailable in the

"SHUFFLE MODE" or "PGM MODE".

– 18 –

Titles can be assigned to each disc or

each track using uppercase and

lowercase letters, numbers, " "

(Katakana) and symbols.

1. Press the [EDIT/NO] button so that

"TITLE ?" is displayed.

2. Press the [YES] button.

… Press the [TITLE EDIT] button if you are

using the remote control unit.

3. Select "DSC" or a track number using the

[

µTRACK≤] dial.

… To assign a disc title, select "TITLE >

DSC" ("DSC" blinks).

… To assign a track title, select "TITLE >

XXX (track number)" (Track number

blinks).

4. Press the [YES] button.

"DSC > _ " or "XXX > _ " is displayed.

… The character entry mode is engaged

and the cursor blinks on the display.

5. Press the [DISPLAY] button to select the

character type.

… When " " is lit: Katakana (square

Japanese syllabary) can be entered.

… When " " is lit: Capital alphabet

letters, numerals and symbols can be

entered.

… When no indicator is lit: Small alphabet

letters, numerals and symbols can be

entered.

6. Select each character by turning the

[

µTRACK≤] dial and pressing [PUSH

ENTER] on the dial.

Assigning Titles (TITLE Function)

7. Repeat steps 5-6.

… Press the[

ª STOP] button to abort the

operation.

… Press the [EDIT/NO] button for more

than 3 seconds (or press the [TITLE

EDIT] button on the remote control unit)

to cancel the title function and resume

playback

8. Press the [YES] button again.

… The disc or track title is displayed again.

… Repeat steps 1-8 to assign titles to other

track numbers.

Select the "CONTINUE" mode with the

[PLAY MODE] button. Titles can be

assigned to the disc and all tracks

successively.

1. Press the [EDIT/NO] button so that

"TITLE ?" is displayed.

2. Press the [YES] button.

… Press the [TITLE EDIT] button if you are

using the remote control unit.

3. Select "TITLE > AINC" with the

[

µTRACK≤] dial ("AINC" blinks).

4. Press the [YES] button.

… The disc title entry mode is engaged

("DSC > _" is displayed) and the cursor

blinks on the display.

… The cursor blinks at the first character

position even if a title has already been

assigned.

5. Press the [DISPLAY] button to select the

character type.

Assigning Titles to the Disc and

All Tracks Successively

(TITLE AUTO INC Function)

Buttons used on this page

Editing Recorded MDs

ENGLISH

ª Character types selectable

… When " " is lit: Katakana (square

Japanese syllabary) can be entered.

… When " " is lit: Capital alphabet

letters, numerals and symbols can be

entered: A B C D E F G H I J K L M N O P

Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9 : ; <

= > ? @ ! " # $ % & ‘ ( )

+ , – . / _ (space)

… When no indicator is lit: Small alphabet

letters, numerals and symbols can be

entered: a b c d e f g h i j k l m n o p q r s

t u v w x y z 0 1 2 3 4 5 6 7 8 9 : ; < = > ? @

! " # $ % & ‘ ( )

+ , – . / _ (space)

ª Changing entered characters

Move the cursor to the character to be

corrected in the character entry mode.

… Select a new character to change the

character at the cursor position.

ª To move the cursor

Deck ® Press the [∆ SEARCH˚ ]

buttons.

Remote Control Unit ® Press the

[∆ SEARCH˚] buttons.

ª To select a character at the cursor

position

Deck ® Turn the [µTRACK≤] dial.

Remote Control Unit ® Press the

[µ TRACK ≤] buttons.

ª To change the character type at the

cursor position

Deck ® Press the [DISPLAY] button.

Remote Control Unit ® Press either the

[DISPLAY] button or [CHAR SELECT]

button.

ª To change the character at the cursor

position to an upper/lower case letter

Deck ® Press the [DISPLAY] button.

Remote Control Unit ® Press the [Aß∑a]

button.

ª To insert a space at the cursor position

Deck ® Press [PUSH ENTER] on the dial

for 3 seconds or more.

Remote Control Unit ® Press the [INSERT]

or [ENTER] button for more than 3 seconds.

ª To enter a number

Deck ® Turn the [µTRACK≤] dial.

Remote Control Unit ® Press the numeric

buttons.

ª To erase a character at the cursor

position

Deck ® Press the [EDIT/NO] button.

Remote Control Unit ® Press either the

[DELETE] button or [EDIT/NO] button.

ª To move the cursor to the right after

selecting a character

Deck ® Press [PUSH ENTER] on the dial.

Remote Control Unit ® Press the [ENTER]

button.

ª To erase all the characters at once

Deck ® Unavailable.

Remote Control Unit ® Press the [CLEAR]

button.

1. In the Stop mode, display the disc title

or track title (number) that you want to

copy with the [µTRACK≤] dial.

(Example): To copy the track 4 title

2. Press the [EDIT/NO] button repeatedly

until "TITLE COPY ?" appears.

3. Press the [YES] button.

"Copy to 001 ?" is displayed.

("001" blinks)

(Example): To copy the track 4 title to track 6

Source track Destination

number track number

4. Select the track to copy the title to with

the [µTRACK≤] dial.

"Copy to 006 ?" is displayed ("006" blinks).

… Press the [ª STOP] button or [EDIT/NO]

button to cancel the TITLE COPY mode.

5. Press the [YES] button.

… The title is copied to track number 006.

… Pressing the [¥PLAY] button or

[π READY] button releases the title copy

operation.

Copying a Title

(TITLE COPY Function)

1. In the Stop mode, press the [EDIT/NO]

button repeatedly until "UNDO ?"

appears.

2. Press the [YES] button.

"Undo OK ?" is displayed.

… To cancel this function, press the

[ª STOP] button or [EDIT/NO] button.

3. Press the [YES] button.

… The last operation is undone and

"COMPLETE" is displayed.

… Pressing the [¥PLAY] button or

[π READY] button releases the UNDO

mode.

Notes:

"UNDO ?" will not be displayed in the cases

below, even if you press the [EDIT/NO]

button (cannot undo).

… When the operation has already been

undone (cannot undo an undo), or no

operation has been performed to undo.

… When the editing mode is released by

pressing the [YES] button.

… During recording or when the

Recording-Ready mode is engaged.

… When "DISC ERASE" is performed on a

blank disc.

… When the power is cut off.

Canceling the Last Operation

(UNDO Function)

– 19 –

Buttons used on this page

Optional Functions

If you connect an IBM-compatible

personal computer keyboard (101 or 106

keys) to the KEYBOARD terminal of this

deck, you can operate the deck control,

track selection, editing and title entry

directly from the keyboard.

… Place the provided lettering guide

around the keyboard function keys for

your reference.

ª Correspondence between deck

buttons and keyboard keys

Deck Buttons Keyboard Keys

[µ] F1 key

[≤] F2 key

STOP button F4 key

PLAY button F5 key

READY button F6 key

RECORD button F8 key

AUTO SPACE button F9 key

REPEAT button F10 key

PLAY MODE button F11 key

DISPLAY button F12 key

YES button Enter key

+10 button + key

Numeric buttons Numeric keys

CLEAR button Shift + F10 keys

EJECT button Shift + F12 keys

∆ßkey

˚∑key

ª Editing keys

Function Key Operation

ERASE TRACK Shift + F1 keys

ERASE DISC Shift + F2 keys

MOVE Shift + F4 keys

DIVIDE Shift + F5 keys

COMBINE Shift + F6 keys

TITLE COPY Shift + F7 keys

TITLE Shift + F8 keys

UNDO Shift + F9 keys

Mode cancellation Esc key

ª Title entry keys

Operation Key Operation

Move cursor ß key, ∑ key

Change track number ™ key, ≈ key

to be edited

Switch uppercase/ Caps key

lowercase

Erase character BS (Back Space)

before cursor key

Erase character on DEL (Delete) key

cursor

Insert character INS (Insert) key

End title entry Esc key

… Characters can be entered directly from

the keyboard.

… When the track number to be edited is

changed using [™] or [≈], the track title

will remain the same.

… " " and " " cannot be used at

the same time.

… When using a keyboard, do not turn the

power on and off rapidly, as this may

sometimes cause the keyboard to

become unoperational.

– 20 –

System Restrictions

Because of the different recording systems

used by Compact Cassette, DAT, etc., the

MD (Mini Disc) is subjected to some

system restrictions. These restrictions may

result in the following problems. These are

normal and are not malfunctions.

… "Track Full" is displayed before the

available recording time expires.

"Track Full" is displayed whenever the

number of allowable tracks is reached,

regardless of the recording time still

available. With the MD system, it is not

possible to record more than 254 tracks.

If you want to record more tracks, erase

unnecessary tracks, record them on

another MD, or use the editing proce-

dure to combine existing tracks.

… "Track Full" is displayed even though

both the number of tracks and the

recording time have not been filled.

Whenever emphasis data or other

signal enhancements are switched on-

off in the middle of tracks, the track is

separated at that point and "Track Full"

may be displayed regardless of the

recording time and number of tracks.

… The remaining recording time of an MD

does not increase although you have

erased several tracks.

The remaining recording time display

ignores tracks shorter than 12 seconds.

Therefore, the time may not increase if

you have erased several short tracks.

… The total elapsed recording time and

remaining recording time does not

coincide with the available recording

time as calculated from the stated time

on the disc, and the recording mode.

The minimum unit for recording data is

usually 6 clusters (approx. 12 seconds).

Data of less than 12 seconds still uses

the 12-second space, so actual

available recording time becomes

shorter than rated. Also, if the MD is

scratched, the scratched sections are

automatically deleted and the time

available is decreased accordingly.

La pagina sta caricando ...

Tascam MD-350 Manuale del proprietario

Marca: Tascam

Modello: MD-350

Categoria: Lettori minidisc

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Tascam MD-350 Owner's manual
français: Tascam MD-350 Le manuel du propriétaire
español: Tascam MD-350 El manual del propietario
Deutsch: Tascam MD-350 Bedienungsanleitung

Documenti correlati

Tascam CD-A630 Manuale del proprietario

Tascam MD-350 Manuale del proprietario

Tascam MD-350 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti