EPOX EP-BX5 Manuale utente

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 2.1

August 16, 1999

EP-BX5EP-BX5

EP-BX5

A PA P

A P

entiumentium

entium

®®

®

II/III/Celer II/III/Celer

II/III/Celer

onon

on

Slot1 Processor based AGPSlot1 Processor based AGP

Slot1 Processor based AGP

mainboarmainboar

mainboar

d (100/66MHz)d (100/66MHz)

d (100/66MHz)

EP-BX5

User Notice

No part of this product, including the product and software may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any

language in any form without the express written permission of EPoX Computer

Company (hereinafter referred to as EPoX) except for documentation kept by the

purchaser for backup purposes.

We provide this manual “as is” without warranty of any kind, either expressed or

implied, including but not limited to the implied warranties or conditions of

merchantability or fitness for a particular purpose. In no event shall EPoX be

liable for any loss of profits, loss of business, loss of use or data, interruption of

business or for indirect, special incidental, or consequential damages of any kind,

even if EPoX has been advised of the possibility of such damages arising from any

defect or error in the manual or product. EPoX may revise this manual from time

to time without notice. For updated BIOS, drivers, or product release information

you may visit our websites at http://www.epox.com or http://www.epox.com.tw.

Products mentioned in this manual are mentioned for identification purposes only.

Product names appearing in this manual may or may not be registered trademarks

or copyrights of their respective companies. The product name and revision

number are both printed on the mainboard itself.

Handling Procedures

Static electricity can severely damage your equipment. Handle the EP-BX5 and

any other device in your system with extreme care and avoid unnecessary contact

with system components on the mainboard. Always work on an antistatic surface

to avoid possible damage to the mainboard from static discharge. Always have the

power supply unplugged and powered off when inserting and removing devices

within the computer chassis. EPoX assumes no responsibility for any damage to

the EP-BX5 mainboard that results from failure to follow instruction or failure to

observe safety precautions.

CAUTION

The EP-BX5 mainboard is subject to

damage by static electricity. Always

observe the handling procedures.

EP-BX5

Technical Support Services

If you need additional information, help during installation or normal use of this

product, please contact your retailer. Your retailer will have the most current

information about your configuration. If your retailer cannot help, you may visit

our online technical support website and/or contact our support technicians at the

locations listed below.

Record your serial number before installing your EP-BX5 mainboard. (The serial

number is located near the ISA slots at the edge of the board.)

EP-BX5 serial number: _________________________________

Contacting Technical Support

EPoX technical support is working hard to answer all of your questions online.

From our website you can find answers to many common questions, drivers, BIOS

updates, tech notes, and important technical bulletins. If you are still unable to

locate the solution you are seeking, you always have the option to contact our

support technicians directly.

North American website (English language)

http://www.epox.com

[email protected]

European website (Multi-language)

http://www.epox.nl

[email protected]

Taiwan website (Chinese language)

http://www.epox.com.tw

[email protected]

Thank you for using EPoX mainboards!

EP-BX5

Table of Contents

Section 1 Introduction

Components Checklist ................................... 1-1

Overview

Pentium

®

II or Pentium

®

III Processor.......... 1-2

S.E.C. Cartridge Terminology ........................1-3

Accelerated Graphics Port............................. 1-4

Hardware Monitoring .....................................1-4

EP-BX5 Form-Factor.....................................1-5

I/O Shield Connector .....................................1-6

Power-On/Off (Remote)................................1-6

System Block Diagram................................... 1-7

Section 2 Features

EP-BX5 Features............................................2-1

Section 3 Installation

EP-BX5 Detailed Layout ...............................3-2

Easy Installation Procedure

Configure Settings.......................................... 3-3

System Memory Configuration .....................3-5

Installing a Pentium

®

II/III Processor............3-8

Device Connectors ......................................... 3-10

External Modem Ring-in Power ON and

Keyboard Power ON Function (KBPO) ........ 3-12

Section 4 Award BIOS Setup

BIOS Instructions ........................................... 4-1

Standard CMOS Setup ....................................4-2

BIOS Features Setup ...................................... 4-3

Chipset Features Setup................................... 4-8

Power Management Setup.............................. 4-12

PNP/PCI Configuration ................................. 4-16

Load Setup Defaults .......................................4-17

Integrated Peripherals .................................... 4-18

Sensor and CPU Speed Setting ......................4-23

Page

EP-BX5

Change Supervisor or User Password ...........4-26

IDE HDD Auto Detection ..............................4-27

Save & Exit Setup ...........................................4-29

Exit Without Saving........................................4-29

Section 5 Appendix

Appendix A

Memory Map ..................................................A-1

I/O Map ...........................................................A-1

Timer & DMA Channels Map ........................ A-2

Interrupt Map .................................................. A-2

RTC & CMOS RAM Map ...............................A-3

Appendix B

POST Codes.................................................... A-5

Unexpected Errors ......................................... A-8

Appendix C

Load Setup Defaults .......................................A-9

Appendix D

GHOST 5.1 Quick User’s Guide....................A-11

EP-BX5

Page Left Blank

IntroductionEP-BX5

Page 1-1

Section 1

INTRODUCTION

Components Checklist

üü

ü A. (1) EP-BX5 mainboard

üü

ü B. (1) EP-BX5 user’s manual

üü

ü C. (1) Floppy ribbon cable

üü

ü D. (1) Hard driver ribbon cables

üü

ü E. (1) Foldable Retention Module

F. (1) Heatsink Support Unit (Optional)

G. (1) PS/2 to AT keyboard connector adapter (optional)

üü

ü H. (1) Bus master drivers

(1) USDM

USER’S

MANUAL

EP-BX5

B

A

G

C

D

F

Top Half

Bottom Half

E

H

or

Introduction EP-BX5

Page 1-2

Overview

Pentium

®

II or Pentium

®

III Processor

The Pentium

®

II or Pentium

®

III Processor (The Pentium

®

III Processor as 300/

100MHz, 350/100MHz, 400/100MHz, 450/100MHz, 500/100MHz and 550/

100MHz speed with 512K-L2 cache Versions.) is the follow-on to the Pentium

®

Processor. The Pentium

®

II or Pentium

®

III Processor, like the Pentium

®

Pro

processor, implements a Dynamic Execution micro-architecture -- a unique

combination of multiple branch prediction, data flow analysis, and speculative

execution. This enables the Pentium

®

II Processor to deliver higher performance

than the Pentium

®

processor, while maintaining binary compatibility with all

previous Intel architecture processors.

A significant feature of the Pentium

®

II or Pentium

®

III Processor, from a system

perspective, is the built-in direct multiprocessing support. In order to achieve

multiprocessing, and maintain the memory and I/O bandwidth to support it, new

system designs are needed. For systems with dual processors, it is important to

consider the additional power burdens and signal integrity issues of supporting

multiple loads on a high speed bus. The Pentium

®

II or Pentium

®

III Processor

card supports both uni-processor and dual processor implementations.

The Pentium

®

II or Pentium

®

III Processor utilizes Single Edge Contact (S.E.C.)

(Figure 1) cartridge packaging technology. The S.E.C. cartridge allows the L2

cache to remain tightly coupled to the processor, while maintaining flexibility

when implementing high performance processors into OEM systems. The second

level cache is performance optimized and tested at the cartridge level. The S.E.C.

cartridge utilizes surface mounted core components and a printed circuit board

with an edge finger connection. The S.E.C. cartridge package introduced on the

Pentium

®

II Processor will also be used in future Slot 1 processors.

The S.E.C. cartridge has the following features: a thermal plate, a cover and a PCB

with an edge finger connection. The thermal plate allows standardized heatsink

attachment or customized thermal solutions. The thermal plate enables a reusable

heatsink to minimize fit issues for serviceability, upgradeability and replacement.

The full enclosure also protects the surface mount components. The edge finger

connection maintains socketabilty for system configuration. The edge finger

connector is denoted as ‘Slot 1 connector’ in this and other documentation.

IntroductionEP-BX5

Page 1-3

The entire enclosed product is called the Pentium

®

II or Pentium

®

III Processor.

The packaging technology and each of the physical elements of the product are

referred to using accurate technical descriptions. This allows clear reference to

the products as just a processor. This is the model used in past packaging tech-

nologies like PGA, TCP, PQFP, DIP, etc.

S.E.C. Cartridge Terminology

• Pentium

®

II or Pentium

®

III Processor

The new enclosed card packaging technology is called a “Single Edge

Contact cartridge.” This is similar to previous names for packaging

technology such as PGA or TCP.

• Processor card

The green PCB (with or without components on it)

• Processor core

The silicon on the PLGA package on the PCB

• Cover

The plastic cover on the opposite side from the thermal plate.

• Slot 1

The slot that the S.E.C. cartridge plugs into, just as the Pentium

®

Pro

processor uses Socket 8.

• Retention mechanism

Formerly ‘retention module’ the dual posts, etc. that holds the cartridge in

place.

• Thermal plate

The heatsink attach-

ment plate.

• Heat sink supports

The support pieces that

are mounted on the

mainboard to provide

added support for

heatsinks.

Figure 1: Pentium

®

II/III Processor CPU

with S.E.C.C. or S.E.C.C.2 Package

Pentium

®

II Processor

in an S.E.C.C. Package

Pentium

®

III Processor

in an S.E.C.C.2 Package

Introduction EP-BX5

Page 1-4

The L2 cache (TagRAM, PBSRAM) components keep standard industry names.

The Pentium

®

II or Pentium

®

III Processor is the first product to utilize the S.E.C.

cartridge technology and Slot 1 connector. Unless otherwise noted, any refer-

ences to “Pentium

®

II Processor,” “Pentium

®

II or Pentium

®

III Processor/Slot 1

processor” or “Pentium III Processor” will apply to both the Pentium

®

II Proces-

sor desktop processors.

Accelerated Graphics Port

(AGP or A.G.P.)

Typically, 3D graphics rendering requires a tremendous amount of memory, and

demands ever increasing throughput speed as well. As 3D products for the

personal computer become more and more popular, these demands will only

increase. This will cause a rise in costs for both end users and manufacturers.

Lowering these costs as well as improving performance is the primary motivation

behind AGP. By providing a massive increase in the bandwidth available between

the video card and the processor, it will assist in relieving some of these pres-

sures for quite sometime.

Hardware Monitoring

Hardware monitoring allows you to monitor various aspects of your systems

operations and status. The features include CPU temperature, voltage and RPM

of fan.

IntroductionEP-BX5

Page 1-5

EP-BX5 Form-Factor

The EP-BX5 is designed with ATX form factor - the new industry standard of

chassis. The ATX form factor is essentially a Baby-AT baseboard rotated 90

degrees within the chassis enclosure and a new mounting configuration for the

power supply. With these changes the processor is relocated away from the

expansion slots, allowing them all to hold full length add-in cards. ATX defines a

double height aperture to the rear of the chassis which can be used to host a wide

range of onboard I/O. Only the size and position of this aperture is defined,

allowing PC manufacturers to add new I/O features (e.g.; TV input, TV output,

joystick, modem, LAN, etc.) to systems. This will help systems integrators

differentiate their products in the marketplace, and better meet your needs.

• Smaller size promotes a smaller system size.

• I/O shield does not need to be retooled in an ATX 2.01 or later. The

mainboard should be used in an ATX 2.01 (or later) compliant case.

• A smaller power supply can be used. High integration on mainboard

reduces the system costs.

Full length

slots

Expandable I/O

5 1/4"

Bay

3 1/2"

Bay

Figure 2: Summary of ATX chassis features

CPU located near

Power Supply

Single chassis

fan for system

Micro

ATX/

ATX

Power

Supply

MicroATX/ATX

power connector

Floppy / IDE

connectors

close to

peripheral

bays

Introduction EP-BX5

Page 1-6

I/O Shield Connector

The EP-BX5 is equipped with an I/O back panel. Please use the appropriate I/O

shield (figure 3).

ATX

POWER SUPPLY

Power-On/Off (Remote)

The EP-BX5 has a single 20-pin connector for ATX power supplies. For ATX

power supplies that support the Remote On/Off feature, this should be connected

to the systems front panel for system Power On/Off button. The systems power

On/Off button should be a momentary button that is normally open.

The EP-BX5 has been designed with “Soft Off" functions. You can turn Off the

system from one of two sources: The first is the front panel Power On/Off the

button, and the other is the "Soft Off" function (coming from the EP-BX5’s

onboard circuit controller) that can be controlled by the operating system.

Windows 95/98 will control this when the user clicks that they are ready to

Shutdown the system.

Figure 4: Case (chassis) Power ON/OFF button

Figure 3: I/O back panel layout

J3

PS/2 Mouse

PS/2 Keyboard

Parallel Port

COM1USB

COM2

(J3: PW-ON)

IntroductionEP-BX5

Page 1-7

Figure 5: System Block Diagram

System Block Diagram

Pentium II or

Processor

Pentium III

PAC

PCI Bridge

and memory

controller

443BX

PllX4E

I/O Bridge

100/66MHz

66MHz

Introduction EP-BX5

Page 1-8

Page Left Blank

FeaturesEP-BX5

Page 2-1

Section 2

FEATURES

EP-BX5 Features:

• EP-BX5 is based on the Pentium

®

II or Pentium

®

III Processor operating

at 233 ~ 400MHz (66MHz) or 300 ~ 550MHz (100MHz) on Slot 1.

There are no jumper setting for CPU Speed Setup but detected automati-

cally through the BIOS.

• Designed with Intel’s 82443 BX AGPset.

• Supports up to 1 GB of SDRAM (minimum of 8 MB) on board, You can

use 168-pin DIMM x 4. It will automatically detect Extended Data Output

(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM)

at 66MHz or 100MHz (please see Section 3-2).

• EP-BX5 will not support Error Checking and Correcting (ECC) when using

paritys DRAM memory modules.

• Supports (2) 16 bit ISA slots, (5) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The EP-BX5 supports (5) PCI

Bus Master slots and a jumperless PCI INT# control scheme which reduces

configuration confusion when plugging in PCI card(s).

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

• Designed with Winbond W83977TF/EF Multi I/O: (1) floppy port, (1)

parallel port (EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported.

• Includes a PS/2 mouse connector.

• Allows use of a PS/2 keyboard.

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.epox.com

please visit our Technical Support section for the latest updates).

Features EP-BX5

Page 2-2

• EP-BX5 utilizes a Lithium battery which provides environmental protec

tion and longer battery life.

• Supports the Universal Serial Bus (USB) connector. The onboard PIIX4E

chip provides the means for connecting PC peripherals such as; keyboards,

joysticks, telephones, and modems.

• Built-in ATX 20-pin power supply connector.

• Software power-down when using Windows

®

95/98.

• Supports ring-in feature (remote power-on through external modem,

allow system to be turned on remotely).

• Resume by Alarm - Allow your system to turn on at a preselected time.

• Power Loss Recovery - In the event of a power outtage your system will

automatically turn itself back on without user intervention.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports Desktop Management Interface (DMI) facilitating the manage-

ment of desktop computers, hardware and software components and

peripherals, whether they are stand-alone systems or linked into networks.

(optional)

• Supports Hot key, Any key or password Keyboard power ON function

(KBPO).

• Supports USDM software to allow the status monitoring of various aspects

of the system when using Windows

®

95/98 or Windows

®

NT 4.0.

• Supports the CPU, PWR and Chassis fan Auto stop in the sleep mode.

• Supports the System Power LED (PANEL) blinks in the sleep mode.

• Built-in WOL (Wake On Lan) Connector.

Installation

EP-BX5

Page 3-1

Section 3

INSTALLATION

Installation EP-BX5

Page 3-2

Figure 1

EP-BX5 Detailed Layout

Installation

EP-BX5

Page 3-3

Easy Installation Procedure

The following must be completed before powering on your new system:

3-1. Configure Jumpers

3-2. System memory Configuration

3-3. Install Pentium

®

II/III/Celeron Processor

3-4. Device Connectors

3-5. External Modem Ring-in Power ON and Keyboard Power ON

Functions (KBPO)

Section 3-1

Configure Settings

The following will describe all of the setting that you are required to set before

moving on to step 3-2.

ROM PCI/ISA BIOS(2A69KPAG)

SENSOR & CPU SPEED SETTING

AWARD SOFTWARE, INC.

Auto Detect DIMM/PCI Clk : Enabled

Spread Spectrum Modulated : Disabled

CPU Host/PCI Clk : Default

CPU/AGP Clk Ratio : Default

CPU Int Clk Ratio : x3

CPU Clk Frequency : 300(100x3) MHz

CPU:AGP (Clk:Clk) : 3:2 (100:66)

CPU Vcore Voltage : +0.10V

CPU Vcore Voltage : 2.10V

** BIOS Writer Utility **

Checksum Error Detect : Both

Source : A:

Target : Mater

Go : Enter

CPU Warning Temperature : Disabled

Extended JP2 Temperature :0

O

C/32

O

C

Current CPU Temperature : 0

O

C/32

O

C

Current System Temperature : 0

O

C/32

O

C

Current POWER FAN Speed :4900 RPM

Current CPU FAN Speed :4900 RPM

Current CHASSIS FAN Speed : 4900 RPM

Vcore : 2.10V Vtt(V) : 1.55V

Vio(V) : 3.47V +5V :5.02V

+12V : 12.40V -12V : -11.95V

-5V : -5.50V VBAT (V) : 3.44V

5VSB (V) : 5.08V

Shutdown Temperature : 60

O

C/140

O

C

Esc:Quit : Select Item

F1 : Help PU/PD/+/-: Modify

F5 : Old Values (Shift) F2 : Color

F7 : Load Setup Defaults

éé

é

êê

ê

èè

è

çç

ç

Installation EP-BX5

Page 3-4

Note: Based on the implementation of the Intel 440BX AGPset, the EP-BX5

is able to provide multiple front side bus (FSB) frequencies for Slot 1

processors and memory operations. The mainboard's FSB is easily se-

lected by BIOS Setup listed above to match the FSB required by your

processor. When using the 100MHz FSB (or higher) you must use

PC100 (or better) compliant SDRAM.

Memory is an important component of any motherboard. When

selecting memory for use on the EPoX brand motherboard we

recommend use only the finest quality modules. EPoX would like to

stress that using non-compliant PC100 SDRAM modules with a

100MHz (or higher) FSB severely compromises the integrity of the

system.

epyTUPCkcolClanretxEoitaR

epyT1tolS

IImuitneP

IIImuitneP

noreleC

draCtrevnoC+073S

66

ro

001

0.2

5.2

0.3

5.3

0.4

5.4

0.5

5.5

0.6

5.6

0.7

5.7

0.8

JP1 = 1-2 - Normal (Default)

= 2-3 - Clear CMOS (momentarily)

JP1 Chassis (Case) intruder detect

1

JP2 The 3th Thermal Connector

1

JP4 Keyboard Power-ON function

JP4 = 1-2 - Enabled

= 2-3 - Normal (Default)

1

La pagina sta caricando ...

EPOX EP-BX5 Manuale utente

Questo manuale è adatto anche per

EPOX EP-BX5 Manuale utente

in altre lingue

Documenti correlati

Altri documenti