MATSONIC MS7122A Manuale utente

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 5.0

October 11, 1999

MS7122AMS7122A

MS7122A

ISA/PCI AGP Mainboard with OnboardISA/PCI AGP Mainboard with Onboard

ISA/PCI AGP Mainboard with Onboard

PCI IDE and Super Multi-I/OPCI IDE and Super Multi-I/O

PCI IDE and Super Multi-I/O

MS7122A

Table of Contents

Section 1 Introduction

Components Checklist ....................................... 1-1

Overview

MS7122A Form-factor ...................................... 1-2

I/O Shield Connector......................................... 1-3

Power-On/Off (Remote).................................... 1-3

System Block Diagram ...................................... 1-4

Section 2 Features

MS7122A Features............................................ 2-1

Section 3 Installation

MS7122A Detailed Layout................................ 3-1

Easy Installation Procedure

Configure DIP Switch........................................ 3-3

System Memory Configuration .......................... 3-4

Device Connectors ............................................ 3-7

External Modem Ring-in Power On and

Keyboard Power On Function (KBPO) ............. 3-9

Section 4 Award BIOS Setup

BIOS Instructions .............................................. 4-1

Standard CMOS Setup....................................... 4-2

BIOS Features Setup ......................................... 4-3

Chipset Features Setup ...................................... 4-8

Power Management Setup ................................. 4-11

PNP/PCI Configuration ..................................... 4-15

Load Setup Defaults .......................................... 4-17

Integrated Peripherals........................................ 4-17

Sensor and CPU Speed Setup ............................ 4-22

MS7122A

Change Supervisor or User Password ............... 4-24

IDE HDD Auto Detection.................................. 4-25

Save & Exit Setup ............................................. 4-27

Exit Without Saving ........................................... 4-27

Section 5 Appendix

Appendix A

Memory Map ..................................................... A-1

I/O Map ............................................................. A-1

Timer & DMA Channels Map ........................... A-2

Interrupt Map..................................................... A-2

RTC & CMOS RAM Map ................................. A-3

Appendix B

POST Codes...................................................... A-4

Unexpected Errors............................................. A-7

Appendix C

Load Setup Defaults .......................................... A-9

Appendix D

GHOST 5.1 Quick User’s Guide ....................... A-11

MS7122A

Page Left Blank

Introduction

MS7122A

Page 1-1

Section 1

INTRODUCTION

Components Checklist

üü

ü A. (1) MS7122A mainboard

üü

ü B. (1) MS7122A user’s manual

üü

ü C. (1) Floppy ribbon cable

üü

ü D. (1) Hard drive ribbon cables

üü

ü E. (1) Driver and utility

USER’S

MANUAL

MS7122A

B

A

C

D

E

Introduction

MS7122A

Page 1-2

MS7122A Form-Factor

The MS7122A is designed with ATX form factor - the new industry standard of

chassis. MicroATX form factor is essentially a Baby-AT baseboard rotated 90

degrees within the chassis enclosure and a new mounting configuration for the

power supply. With these changes the processor is relocated away from the

expansion slots, allowing them all to hold full length add-in cards. ATX defines a

double height aperture to the rear of the chassis which can be used to host a wide

range of onboard I/O. Only the size and position of this aperture is defined,

allowing PC manufacturers to add new I/O features (e.g.; TV input, TV output,

joystick, modem, LAN, etc.) to systems. This will help systems integrators

differentiate their products in the marketplace, and better meet your needs.

• By integrating more I/O down onto the board and better positioning the hard

drive and floppy connectors material cost of cables and add-in cards is

reduced.

• By reducing the number of cables and components in the system, manufac-

turing time and inventory holding costs are reduced and reliability will

increase.

• By using an optimized power supply, it's possible to reduce cooling costs and

lower acoustical noise. An ATX power supply, which has a side-mounted fan,

allows direct cooling of the processor and add-in cards making a secondary

fan or active heatsink unnecessary in most system applications.

Full length

slots

Expandable I/O

5 1/4"

Bay

3 1/2"

Bay

Figure 2: Summary of MicroATX chassis features

CPU located near

Power Supply

Single chassis

fan for

system

ATX

Power

Supply

ATX power

connector

Floppy / IDE

connectors

close to

peripheral

bays

Introduction

MS7122A

Page 1-3

ATX

POWER SUPPLY

MS7122A Board

Power-On/Off (Remote)

The MS7122A has a single 20-pin connector for ATX power supplies. For ATX

power supplies that support the Remote On/Off feature, this should be connected

to the systems front panel for system Power On/Off button. The systems power

On/Off button should be a momentary button that is normally open.

The MS7122A has been designed with “Soft Off" functions. You can turn Off the

system from one of two sources: The first is the front panel Power On/Off

button, and the other is the "Soft Off" function (coming from the MS7122A’s

onboard circuit controller) that can be controlled by the operating system. Win-

dows 95 will control this when the user clicks that they are ready to Shutdown the

system.

Figure 4: Simple ATX Power ON/OFF Controller

Case (chassis) Power

ON/OFF button (J 3)

J 3

I/O Shield Connector

The MS7122A is equipped with an I/O back panel. Please use the appropriate I/

O shield (figure 3).

PS/2 Mouse

PS/2

KEYBOARD

USB port

COM1 COM2

parallel port

Speaker

Line_in

MIC

Figure 3: I/O back panel layout

Joystick/Midi port

Introduction

MS7122A

Page 1-4

Figure 5: System Block Diagram

System Block Diagram

PAC

PCI Bridge

and memory

controller

VT82C693

VT82C686A

I/O Bridge

100/66MHz

66MHz

AC

97

Pentium II

socket 370

Processor

USB 0,1 USB 2,3

FeaturesMS7122A

Page 2-1

Section 2

FEATURES

MS7122A Features:

• MS7122A is based on the Mendocino Processor operating at 300 ~

466MHz on PGA370. The board is configured by an ESSJ (Easy-Setting-

Single-Jumper) to match your CPU clock speed.

• Designed with VIA Apollo Pro PCIset.

• Supports up to 768MB of DRAM (minimum of 8 MB) on board (please

see Section 3-2).

• MS7122A will support Error Checking and Correcting (ECC) when using

parity SDRAM memory modules. This will detect multiple bit errors and

correct 1-bit memory errors.

• Supports (1) 16 bit ISA slots, (4) 32 bit PCI slots, (1) AGP slot, (1) AMR

slot and provides (2) independent high performance PCI IDE interfaces

capable of supporting PIO Mode 3/4 and Ultra DMA 33/66 devices.

The MS7122A supports (4) PCI Bus Master slots and a jumperless PCI

INT# control scheme which reduces configuration confusion when plugging

in PCI card(s).

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

• Designed with on chip Multi I/O: (1) floppy port, (1) parallel port (EPP,

ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released.

• MS7122A utilizes a Lithium battery which provides environmental protec

tion and longer battery life.

• Supports the (4) Universal Serial Bus (USB) Ports. The onboard

VT82C686A chip provides the means for connecting PC peripherals such

as; keyboards, joysticks, telephones, and modems.

Features

MS7122A

Page 2-2

• Built-in ATX 20-pin power supply connector.

• Software power-down when using Windows

®

95/98.

• Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely).

• Resume by Alarm - Allows your system to turn on at a preselected time.

• Power Loss Recovery - In the event of a power outtage your system will

automatically turn itself back on without user intervention.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports Keyboard power ON function (KBPO).

• Built-in WOL (Wake-up On Lan) Connector.

• Built-in AC97 PCI Audio.

Installation

MS7122A

Page 3-1

Section 3

INSTALLATION

Installation

MS7122A

Page 3-2

Figure 1

MS7122A Detailed Layout

Installation

MS7122A

Page 3-3

Easy Installation Procedure

The following must be completed before powering on your new system:

3-1. Configure DIP Switch and Jumper to match your hardware

3-2. System memory Configuration

3-3. Device Connectors

3-4 External Modem Ring-in Power ON and Keyboard Power ON

Functions (KBPO)

Section 3-1

Configure DIP Switch

We design this motherboard with a DIP Switch to make your install fast and easy.

The following will describe all of the DIP Switch that you are required to set

before moving on to step 3-2.

Note: The DIP Switch as depicted as shown (Figure 1) in their correct

physical orientation.

1

2

34

ON

1WS)zHM(UPC

1234 oitaRzHM66zHM001

NONONOX4662004

NONOX5.4003054

NONOX5333005*

NOX5.5663055*

NONONOX6004006*

NONOX5.6334056*

NONOX7664007*

NOX5.7005*057*

NONOX8335*008*

*reserved

JP1 Clear COMS

1-2 : Run Mode(default)

2-3 : Clear CMOS

JP4 Keyboard Power-ON Function Selection

1-2 : Disabled

2-3 : Enabled

Installation

MS7122A

Page 3-4

Section 3-2

System Memory Configuration

Memory Layout

The MS7122A supports (3) 168-pin DIMMs (Dual In-line Memory Module).

The DIMMs can be either EDO (Enhanced Data Out) or SDRAM

(Synchronized DRAM).

• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or

125MHz (8ns) bus speed.

• If you use both 50ns and 60ns memory you must configure

your BIOS to read 60ns.

• When using Synchronous DRAM we recommend using the

4 clock variety over the 2 clock.

Figure 2 and Table 1 show several possible memory configurations using both

SIMM and DIMM.

* SDRAM only supports 8, 16, 32, 64, 128, 256MB DIMM modules.

Table 1

DIMM 1

DIMM 2

Bank 0

Bank 1

-Synchronous

-EDO

DIMM 3

Bank 2

yromeMlatoT

1MMID

)0knaB(

2MMID

)1knaB(

3MMID

)2knaB(

BM652=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

enoNenoN

BM215=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

enoN

BM867=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

Installation

MS7122A

Page 3-5

DIMM Module Installation

Figure 3 displays the notch marks and what they should look like on your

DIMM memory module.

DIMMs have 168-pins and two notches that will match with the onboard DIMM

socket. DIMM modules are installed by placing the chip firmly into the socket

at a 90 degree angle and pressing straight down (figure 4) until it fits tightly into

the DIMM socket (figure 5).

Figure 3

Figure 4

DIMM Module clip before installation

LEFT KEY ZONE

(UNBUFFERED)

CENTER KEY ZONE

(3.3 V DRAM)

Installation

MS7122A

Page 3-6

Figure 5

DIMM Module clip after installation

To remove the DIMM module simply press down both of the white clips on either

side and the module will be released from the socket.

Installation

MS7122A

Page 3-7

Section 3-3

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your

connections (figure 6).

J2: Chassis Panel Connector

• Power LED, Speaker, Reset

J3: Turbo LED, HDD LED, IR Conn., Sleep/Power_ON

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J6: Chassis Fan Power

• A plug-in for the chassis Fan Power

J7: WOL Connector

IDE1: Primary IDE

IDE2: Secondary IDE

FDD1:Floppy Controller Connector

PW1: ATX Power Connector

• 20-pin power connector

CD1: CD Audio Connector

AUX1:AUX Audio Connector

Figure 6

PS/2 Mouse

PS/2

KEYBOARD

USB port

COM1 COM2

parallel port

Speaker

Line_in

MIC

Joystic/Midi port

Installation

MS7122A

Page 3-8

Power On/Off - This is connected to the power button on the case.

Using the Soft-Off by Pwr-BTTN feature, you can choose either

Instant Off (turns system off immediatly), or 4 sec delay (you need

to hold the button down for 4 seconds before the system turns off).

When the system is in 4 sec delay mode, we has added a special

feature to make the system go into suspend mode when the button

is pressed momentarily.

J2

Device Connectors (continued)

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Turbo LED indicator - LED ON when higher speed is selected

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

IDE LED indicator - LED ON when Onboard PCI IDE Hard

disks is activate

Power LED connector

1. Power LED(+) 4. NC

2. N/C 5. GND

3. GND

J3

1

+

1

Installation

MS7122A

Page 3-9

Section 3-4

External Modem Ring-in Power

ON and Keyboard Power ON

Functions (KBPO)

On the basis of bounded functions in I/O chipset, the two serial ports are able to

support the External Modem Ring-in Power ON function. Once users connect

the external modem to COM1 or COM2, the MS7122A mainboard allows users

to turn on their system through the remote and host's dial-up control.

Exclusive Keyboard Power ON Function

To innovate a unique feature to benefit users, we devoted the easiest and most

convenient way to turn on your system based on the the ATX power supply.

How to work with it

Step 1: Please check JP4 at the position 2-3 after you finished the system

installation.

Step 2: You can enjoy the Keyboard Power ON function (KBPO) by pressing

any 2 key and BUTTON only to turn on your system. Your system will

be turned on automatically, after releasing the keys. To power off you

system, you can use the Soft-OFF function under Windows 95.

Notes: Intel ATX version 2.0 specification has recommended you use the

power supply with 0.72A(720mA) in 5.0VSB. With our MS7122A

mainboard, the 5.0VSB standby power only has to be > = 0.2A (200mA)

then you can enjoy this unique benefit. However, the ATX power

supply which is < 0.2 (200mA) is still applicable to your system by

placed JP4 at the position 1-2 to disable this feature.

JP4 Keyboard Power-ON Function Selection

1-2 : Disabled

2-3 : Enabled

(Default)

Installation

MS7122A

Page 3-10

Page Left Blank

La pagina sta caricando ...

MATSONIC MS7122A Manuale utente

MATSONIC MS7122A Manuale utente

in altre lingue

Documenti correlati

Altri documenti