Lutron Electronics QS Timeclock Quick Installation And Operation Manual

QS Timeclock

(for lights and window treatments/shades)

Quick Installation

and Operation Guide

Please Read

The QS Timeclock is a premier energy-saving astronomic timeclock for lights

and window treatments, which integrates seamlessly with the Lutron Energi

Savr Node components and QS window treatments.

Model Number: QSGR-TC-3S-WH

Rating: 120 –240 V~ 50 / 60 Hz 100 mA

Output: 24 V- 150 mA IEC PELV/NEC® Class 2 supply

English

®

Français Español Português Deutsch Italiano Nederlands 中文

Contents

Features and Functions ..................2

Line Voltage Wiring .....................3

Terminations ..........................3

Line Voltage Wiring Details ...............4

Overview of IEC PELV/NEC® Class 2 Wiring ..5

QS Link Wiring ........................6

Completing Installation ..................8

Programming Mode ....................9

Timeclock Operation

Setting Time and Date .................10

Setting Location .....................11

Setting Daylight Saving Time ...........11

Adding an Event .....................12

Deleting / Viewing an Event .............13

Setting / Viewing / Deleting a Holiday ......14

Copying / Deleting a Schedule ...........15

Troubleshooting .......................16

Warranty, Contact Information ...........18

For additional features and advanced functions,

see the complete installation and operation guide

(P/N 032383) at www.lutron.com

OK

12

3

4

5

6

Info screen

Displays programming

functions

Program buttons

Shade (window treatment)

button groups

Preset and raise/lower

buttons with integral LEDs

(maximum of 3 button

groups)

Timeclock button

Displays current

timeclock info

OK button

Used for programming,

navigation

USB type mini B

For programming via PC

Features and Functions

QS Timeclock Quick Installation and Operation Guide 2

®

QS Timeclock Quick Installation and Operation Guide 3

®

D1 D1 D2 D2

• Pull power wiring from distribution panel to QS Timeclock.

• Each line voltage terminal can accept one 12 AWG (4.0 mm²) wire.

Line Voltage Wiring

D1 D1 D2 D2

NOT USED

Rear of

QS Timeclock

1234

12

ABC

123456LN

Line voltage (Line / Hot)

is labeled L.

100–240 V~ only

Distribution Panel

1234

12

ABC

123456LN

Terminations

QS Communication link

Contact closure input and 24 V- power

NOT

USED

Input Power

L: Line / Hot

N: Neutral

: Ground

Line Voltage Wiring Details

• Use properly certified cable for all line

voltage/mains cables.

• Proper short-circuit and overload

protection must be provided at the

distribution panel.

• Install in accordance with all local and

national electrical codes.

• IEC PELV/NEC® Class 2 terminals may

be temporarily unplugged for ease of

contact closure and control wiring.

• Notice: Risk of damage to unit. Do not

connect line voltage/mains cable to IEC

PELV/NEC® Class 2 terminals.

Step 1: Install wallbox. Mount a 3` in

(89 mm) deep 4-gang U.S. wallbox on a

dry, flat indoor surface that is accessible

and allows for system programming and

operation. Allow at least 4` in (110 mm)

clearance above and below the faceplate

to ensure proper heat dissipation. Allow

1 in (25 mm) for faceplate overhang on

all sides.

Note: 4-gang wallbox available from

Lutron; P/N 241400.

Step 2: Check wiring.

• Earth/ground terminal connection must

be made as shown in wiring diagrams

(see page 3).

• Follow all local and national electrical

codes when installing IEC PELV/NEC®

Class 2 wiring with line voltage/mains

wiring.

WARNING! Electric Shock hazard.

May result in Serious Injury or

Death. Always turn off circuit

breaker or remove main fuse from

power line before doing any work.

Step 3: Connect line voltage.

• Strip 9 in (8 mm) of

insulation off the line

voltage/mains cables in

the wallbox.

• Connect the line voltage/mains and

ground wires to the appropriate terminals

on the back of the timeclock.

L: Line / Hot

N: Neutral

: Ground

The recommended installation torque is

5.0 in∙lb (0.6 N∙m) for line voltage/mains

connections and 5.0 in∙lb (0.6 N∙m) for

the earth/ground connection.

Notice: Risk of damage to unit.

The QS Timeclock must be in stalled by

a qual i fied electrician in accordance with

all applica ble reg u la tions and building

codes. Im prop er wiring can result

in dam age to the timeclock or oth er

equipment.

QS Timeclock Quick Installation and Operation Guide 4

®

Faceplate overhangs

wallbox on all sides;

allow 1 in (25 mm)

4` in

(110 mm)

9 in

(8 mm)

Contact Closure Input Wiring

24 V- 50 mA

For settings, see CCI Setup.

12

ABC

N H123456

1234

Note: Use appropriate wire

connecting devices as

specified by local codes.

Example:

Third-party contact

closure to enable /

disable timeclock

1: COM

2: 24 V-*

3: MUX

4: MUX

Control Wiring

24 V- 100 mA

Overview of IEC PELV/NEC® Class 2 Wiring

18 AWG (1.0 mm

2

)

each terminal

A: CCI SIG

B: 24 V-

C: CCI COM

To other

QS devices

Data (terminals 3 and 4):

Twisted, shielded pair 22 AWG (0.5 mm

2

) each terminal

Common and power (terminals 1 and 2):

Two 18 AWG (1.0 mm

2

) each terminal (for link <500 ft/153 m)

Two 12 AWG (4.0 mm

2

) each terminal (for link 500–2000 ft/153–610 m)

* Do not connect terminal 2

between a QS Timeclock

and any other power supply.

QS Timeclock Quick Installation and Operation Guide 5

®

IEC PELV/NEC® Class 2 control wiring

(2) 18 AWG (1.0 mm

2

)

1: Common

2: 24 V-

Wiring Detail

For links 500–2000 ft (153–610 m)

4

3

2

1

Data link: (1) twisted, shielded pair

22 AWG (0.5 mm

2

)

3: MUX

4: MUX

(2) 12 AWG

(4.0 mm

2

)

(2) 12 AWG

(4.0 mm

2

)

NOT

USED

QS Timeclock Quick Installation and Operation Guide 6

®

• Each IEC PELV/NEC® Class 2 terminal

accepts up to two 18 AWG (1.0 mm²)

wires.

• Connect the terminal 1, 3, and 4

connections to all control units,

wallstations, and control interfaces.

• Total length of control link must not

exceed 2000 ft (610 m).

• Do not allow IEC PELV/NEC® Class 2

wires to contact line/mains wires.

• The QS Timeclock provides 3 PDUs

(Power Draw Units) on the QS Link.

For more information, see Lutron

P/N 369405, “Power Draw Units on the

QS Link” at www.lutron.com

QS Communication Link

Terminal Detail

QS Link Wiring

D1 D1 D2 D2

_

MUX

24 V-

COM

LUTRON

LUTRON LUTRON LUTRON

Energi Savr Node

Sivoia QS

smart

power

panel

Sivoia QS

shade

Sivoia QS

shade

QS Timeclock

Wallstation

Wallstations

Connect all 4

terminals within a

power group:

1: Common

2: 24 V-

3 and 4: Data

Connect only 3

terminals between

power groups:

1: Common

3 and 4: Data

Do not connect

Terminal 2: 24 V-

A

B

A

B

Power Group 1

Power Group 2

Power Group 3

Power Group 4

Energi Savr Node

Wiring Example

• System communication uses

IEC PELV/NEC® Class 2 wiring.

• Follow all local and national electrical

codes when installing IEC PELV/NEC®

Class 2 wiring with line voltage/

mains wiring.

• Make all connections in the control

unit’s wallbox.

• Wiring can be T-tapped or daisy-chained.

• 24 V- 100 mA IEC PELV/NEC® Class 2.

QS Link Wiring (continued)

QS Timeclock Quick Installation and Operation Guide 7

®

T-Tap Wiring Example

LUTRON LUTRONLUTRON LUTRON

LUTRON LUTRON LUTRON

LUTRON

LU

TRON

LUTRON LUTRON LUTRON

QS Timeclock

seeTouch QS

Sivoia QS

Shade

Sivoia QS

smart panel

Energi Savr Node

LUTRON LUTRONLUTRON LUTRON

LUTRON LUTRON LUTRON

LUTRON

LU

TRON

LUTRON LUTRON LUTRON

Sivoia QS

smart panel

QS Timeclock

Sivoia QS

Shade

seeTouch QS

Daisy-Chain Wiring Example

Energi Savr Node

Note: The QS Timeclock provides

3 power draw units on the QS link.

For more information on PDUs, see

“Power Draw Units on the QS Link”,

PN 369405 at www.lutron.com

Wire Sizes (check compatibility in your area)

QS Link Wiring Length Wire Gauge Lutron Cable Part Number

Less than 500 ft (153 m) Power (terminals 1 and 2)

1 pair 18 AWG (1.0 mm

2

) GRX-CBL-346S (non-plenum)

GRX-PCBL-346S (plenum)

Data (terminals 3 and 4)

1 twisted, shielded pair 22 AWG (0.5 mm

2

)

500 to 2000 ft

(153 to 610 m)

Power (terminals 1 and 2)

1 pair 12 AWG (4.0 mm

2

) GRX-CBL-46L (non-plenum)

GRX-PCBL-46L (plenum)

Data (terminals 3 and 4)

1 twisted, shielded pair 22 AWG (0.5 mm

2

)

Completing Installation

1. Mount the QS Timeclock in the wallbox

as shown using the four screws pro vid ed.

Note: Follow all local and national

electrical codes when installing IEC PELV/

NEC® Class 2 wiring with line voltage/

mains wiring.

2. Verify installation.

3. Restore power.

4. Apply the protective overlay to the QS

Timeclock.

QS Timeclock Quick Installation and Operation Guide 8

Note: When tightening mounting

screws, make sure that the hinged

cover and faceplate will open fully,

as shown.

Wall

7.9 in

(200 mm)

3.5 in

(87 mm)

3.75 in

(95 mm)

Protective overlay

(apply after installation)

Faceplate

(apply after installation)

®

Entering and Exiting Programming Mode

To enter programming mode:

Press and hold the top and bottom

programming buttons simultaneously for

3 seconds. The LEDs in the scene buttons

will scroll from top to bottom, confirming

that you are in programming mode, and the

info screen will display the main menu.

To exit programming mode:

Press and hold the top and bottom

programming buttons simultaneously for

3 seconds.

Navigating Menus in Programming Mode

Master Buttons

The Master buttons allow you to move through the menu

choices. The current choice is highlighted on the info screen.

OK Button

The OK button chooses the current highlighted menu choice.

This will either take you to the next menu or accept a setting you

have selected. When the screen displays a Yes / No question, the

OK button is “Yes”.

Timeclock Button

The timeclock button functions as a “back” button during

programming mode. Pressing the timeclock button takes you

back one step in the current menu. Pressing it repeatedly

will eventually return you to the main menu, but will not exit

programming mode. When the screen displays a Yes / No

question, the Timeclock button is “No”.

Programming Mode

Main menu

CCI setup

Timeclock

QS Timeclock Quick Installation and Operation Guide 9

®

OK

12

3

4

5

6

Press and hold the top

and bottom buttons for

3 seconds to enter or exit

programming mode

Master buttons

OK button

Timeclock (back) button

QS Timeclock Quick Installation and Operation Guide 10

®

Timeclock Operation

Setting Time and Date

1. Enter programming mode.

2. Use the Master buttons to highlight “Timeclock” and press the

OK button to accept.

3. Use the Master buttons to highlight “Time & date” and press

the OK button to accept.

4. Use the Master buttons to highlight either “12 Hr” or “24 Hr”

format for time display and press the OK button to accept.

5. Use the Master buttons to highlight the current hour and press

the OK button to accept. Repeat for the current minutes.

6. Use the Master buttons to highlight the current year and press

the OK button to accept. Repeat for the current month and

date.

7. The info screen will confirm that your time and date have

been saved.

8. Exit programming mode.

Main menu

Timeclock

Scene setup

Timeclock

End afterhours

Time & date

Set time

: 00 AM

08

Timeclock

Set date

: 00

2009

Set date

Set format

12 Hr

March

Set date

17

Set time

08 : AM

30

Saved

OK

1 2 3 4 5 6

Master

buttons

OK

button

Timeclock

(back) button

QS Timeclock Quick Installation and Operation Guide 11

®

Setting Daylight Saving Time

1. Enter programming mode and

select “Timeclock”. Use the Master

buttons to highlight “Set DST” and

press the OK button to accept.

2. Use the Master buttons to highlight

“YES” if your location observes

daylight saving time, or “NO” if it

does not. Press the OK button to

accept.

3. If yes, use the Master buttons to

choose either “USA 2007” (the

second Sunday in March to the first

Sunday in November), or “Other.”

For “Other,” follow the screens to

set start and end dates and amount

of time.

4. Press the OK button to accept. The

info screen will confirm that your

time and date have been saved.

5. Exit programming mode.

Timeclock Operation (continued)

Setting Location

1. Enter programming mode.

2. Use the Master buttons to highlight

“Timeclock” and press the OK button to

accept.

3. Use the Master buttons to highlight

“Location” and press the OK button to

accept.

4. Use the Master buttons to set your

location by either country and city

or latitude and longitude. Press the

OK button to accept.

5. Use the Master buttons to highlight

the country and press the OK button

to accept. Repeat for the state and

closest city.

6. The info screen will confirm that your

time and date have been saved.

7. Exit programming mode.

Main menu

Timeclock

Scene setup

Timeclock

Time & date

Location

Location by

Lat/Longitude

Country, City

Timeclock

State

Pennsylvania

City

Philadelphia

Country

08 : 00

USA

Timeclock

Location

Set DST

DST

: 00

Yes

Saved

OK

1 2 3 4 5 6

Master

buttons

OK

button

Timeclock

(back) button

QS Timeclock Quick Installation and Operation Guide 12

®

Timeclock Operation (continued)

Adding an Event

1. Enter programming mode.

2. Use the Master buttons to highlight “Timeclock” and press the OK

button to accept.

3. Use the Master buttons to highlight “Add events” and press the

OK button to accept.

4. Use the Master buttons to highlight the recurrence for this event:

day of the week, holiday, weekdays or weekends. Press the OK

button to accept.

5. Use the Master buttons to highlight the type of the event (fixed time of day or a relative time to sunrise or

sunset). Press the OK button to accept.

6. For a fixed-time event, use the Master buttons to highlight the hour for your event to begin; press the OK

button to accept. Repeat for the minutes.

For a relative-time event, use the Master buttons and the OK button to set the hour, then the minutes relative

to sunrise or sunset (maximum of 1 hour, 59 minutes before or after sunrise or sunset).

7. Use the Master buttons to highlight the desired action for the timeclock event:

• Scenes 1-16, Off

• Window Treatment Groups 1-3 open, preset, or close

• Start/End Afterhours

8. The info screen will confirm that your event has been saved.

9. Repeat steps 4 through 9 for additional events.

10. Exit programming mode.

Main menu

Timeclock

Scene setup

Timeclock

Add events

Monday

Add events

Time of day

Add events

Scene

Scene 1

Set time

: 00 AM

08

Saved

Timeclock

View events

Add events

OK

1 2 3 4 5 6

Master

buttons

OK

button

Timeclock

(back) button

QS Timeclock Quick Installation and Operation Guide 13

®

Timeclock Operation (continued)

Deleting an Event

1. Enter programming mode.

2. Use the Master buttons to highlight

“Timeclock” and press the OK button to

accept.

3. Use the Master buttons to highlight

“Delete events” and press the OK button

to accept.

4. Use the Master buttons to highlight the

day of the week (or holiday) when the

event occurs; press the OK button to

accept.

5. Use the Master buttons to highlight the

event to delete; press the OK button to

accept.

6. A screen will appear, verifying you wish to

delete the event. Press the OK button to

accept and delete; otherwise, press the

timeclock button to go back.

7. The info screen will confirm that your

event has been deleted.

8. Exit programming mode.

Main menu

Timeclock

Scene setup

Timeclock

Copy schedule

Timeclock

Delete?

Delete

8:00 AM

Scene 5

Delete

Monday

01/03

Viewing an Event

1. Enter programming mode, select

“Timeclock,” and select “View events”.

2. Use the Master buttons to highlight the

day of the week (or holiday) when the

event occurs; press the OK button to

accept.

3. Use the Master buttons to highlight the

event to view; press the OK button to

accept.

4. Press the OK button to return to the

Timeclock menu.

5. Exit programming mode.

Timeclock

Delete events

Add events

View events

Monday

View

8:00 AM

Scene 5

View events

Monday

1/3

R

Delete events

Deleted

OK

12

3

4

5

6910

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

QS Timeclock Quick Installation and Operation Guide 14

®

Timeclock Operation (continued)

Setting a Holiday

1. Enter programming mode.

2. Use the Master buttons to highlight

“Timeclock” and press the OK button

to accept.

3. Use the Master buttons to highlight

“Holiday” and press the OK button to

accept.

4. Use the Master buttons to highlight

“Set holiday” and press the OK button

to accept.

5. Use the Master buttons to highlight

the month of the holiday and press the

OK button to accept. Repeat for the

date.

6. The info screen will confirm that your

holiday has been set.

7. Exit programming mode.

Note: The QS Timeclock supports up

to 25 unique holidays. Follow the

steps in “Adding an Event” to

add Holiday timeclock events.

Timeclock

Delete schedule

Holiday

Add event

View holiday

Set holiday

Holiday

Set holiday

1/25

1

Feb

Monday

Set holiday

1/25

Feb

14

Deleting a Holiday

1. Enter programming mode, select

“Timeclock,” select “Holiday,” and

select “Delete holiday”.

2. Use the Master buttons to highlight the

holiday you wish to delete (or delete all

holidays) and press the OK button to

accept.

3. Press the OK button to delete the

selected holiday. The info screen

will confirm that your holiday has

been deleted.

4. Exit programming mode.

Holiday

View holiday

Delete holiday

Monday

Saved

Deleted

Viewing a Holiday

1. Enter programming mode, select

“Timeclock,” select “Holiday,” and select

“View holiday”.

2. Use the Master buttons to scroll through

the dates of the programmed holidays.

3. If no holidays are programmed, the

info screen will display a screen

informing you.

4. Exit programming mode.

View Holiday

1/25

Feb 14

Monday

No Holidays

OR

Delete holiday

1/2

Feb 14

Delete holiday

1/2

Delete?

OK

1 2 3 4 5 6

Master

buttons

OK

button

Timeclock

(back) button

QS Timeclock Quick Installation and Operation Guide 15

®

Timeclock Operation (continued)

Copying a Schedule

1. Enter programming mode.

2. Use the Master buttons to highlight

“Timeclock” and press the OK button

to accept.

3. Use the Master buttons to highlight

“Copy Schedule” and press the

OK button to accept.

4. Use the Master buttons to highlight the

day you want to copy the schedule from

and press the OK button to accept.

5. Use the Master buttons to highlight the

day you want to copy the schedule to

and press the OK button to accept.

6. The info screen will ask you to confirm

overwriting all events occurring on the

selected day to copy to; press the OK

button to accept.

7. Exit programming mode.

Timeclock

Delete schedule

Delete events

Copy schedule

Copy from

Monday

Timeclock

Overwrite

all events?

Deleting a Schedule

1. Enter programming mode,

select “Timeclock,” and select

“Delete schedule”.

2. Use the Master buttons to highlight the

day of the schedule you wish to delete

and press the OK button to accept.

3. The info screen will confirm that your

event has been deleted.

4. The info screen will ask you to confirm

deleting the schedule on the selected

day; press the OK button to accept.

5. Exit programming mode.

Timeclock

Delete events

Delete schedule

Saved

Delete

Sunday

schedule?

Monday

Copy to

Tuesday

Monday

Delete schedule

Sunday

OK

1 2 3 4 5 6

Master

buttons

OK

button

Timeclock

(back) button

QS Timeclock Quick Installation and Operation Guide 16

®

Symptom Possible Causes Remedy

Unit does not power up

Circuit breaker is tripping

Circuit Breaker is off Switch circuit breaker on

Miswire Verify wiring to unit and loads

System short circuited Find and correct shorts

Integral (direct-wired) contact closure input does not

work

Miswire Check wiring on contact closure input

Input CCI signal is not received Verify the input device is operating properly

Unit is in wrong CCI mode and/or type Change to correct CCI mode and/or type for your application

QS devices on link are not working Miswire or loose connection on QS link Verify QS link wiring to all devices

QS device programming is incorrect Verify the functionality and programming on the QS devices

Timeclock events do not occur

Sunrise or sunset events do not occur at the correct

time

Timeclock is disabled Enable the timeclock

Time/date is not set correctly Set the time/date

Location is not set correctly Set the latitude and longitude of the unit’s location

Holiday schedule is in effect Normal schedule will resume when the holiday ends

Security lockout from programming mode Security password set incorrectly Call Lutron Technical Support to reset password

Window treatment EDU (electronic drive unit) will not

move

EDU is not powered Connect power to EDU

Window treatment fabric is caught on something Check and unbind window treatment fabric

EDU is not assigned to a shade button group Assign the EDU to a shade button group

Shade button group will not control any window

treatment

All limits are set to the same height Verify limit settings

Communications link is not wired to the EDU Check and wire the EDU link

EDU has been unassigned from shade button group Reassign the EDU to the shade button group

Window treatment EDU does not fully open or fully

close

Limits have been set incorrectly Set limits correctly

Window treatment fabric is caught on something Check and unbind window treatment fabric

Window treatment moves in the opposite direction

when raise/lower buttons are pushed

Open and close limits have been reversed Set limits correctly

Shade button group does not operate all the window

treatments it is assigned to

EDU has been unassigned from shade button group Reassign the EDU to the shade button group

All limits are set to the same height Verify limit settings

EDU is not wired correctly Check and rewire EDU

Shade button group is not wired correctly Check and rewire shade button group

Window treatments in a room move on their own EDUs are assigned to a shade button group in

another room

Reassign the EDU to the correct shade button group

Troubleshooting

QS Timeclock Quick Installation and Operation Guide 17

®

Notes

®

Warranty

For full warranty information, see www.lutron.com/TechnicalDocumentLibrary/Warranty_CommercialSystems.pdf

®

Lutron, Lutron, Energi Savr Node, GRAFIK Eye, seeTouch, and Sivoia are trademarks or registered trademarks of Lutron Electronics Co., Inc. in

the US and/or other countries.

NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.

Contact Information

Internet: www.lutron.com

E-mail: product@lutron.com

WORLD HEADQUARTERS

USA

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299

TEL +1.610.282.3800

FAX +1.610.282.1243

Customer Assistance:

1.844.LUTRON1

[email protected]

www.lutron.com/support

North and South America

Customer Assistance

USA, Canada, Caribbean:

1.844.LUTRON1 (1.844.588.7661)

Mexico: +1.888.235.2910

Central/South America: +1.610.282.6701

EUROPEAN HEADQUARTERS

United Kingdom

Lutron EA Limited

125 Finsbury Pavement

4th floor, London EC2A 1NQ

United Kingdom

TEL: +44.(0)20.7702.0657

FAX: +44.(0)20.7480.6899

FREEPHONE (UK): 0800.282.107

Customer Assistance:

+44.(0)20.7680.4481

[email protected]

ASIAN HEADQUARTERS

Singapore

Lutron GL Ltd.

390 Havelock Road

#07-04 King’s Centre

Singapore 169662

TEL: +65.6220.4666

FAX: +65.6220.4333

Customer Assistance: 800.120.4491

lutronsea@lutron.com

Asia Customer Assistance

Northern China: 10.800.712.1536

Southern China: 10.800.120.1536

Hong Kong: 800.901.849

Indonesia: 001.803.011.3994

Japan: +81.3.5575.8411

Macau: 0800.401

Singapore: 800.120.4491

Taiwan: 00.801.137.737

Thailand: 001.800.120.665853

Other countries: +65.6220.4666

Lutron Electronics Co., Inc.

P/N 032535 Rev. A 03/2019

L'horloge QS

(pour éclairage et traitements de fenêtres/stores)

Guide rapide d’installation

et de fonctionnement

À lire attentivement

L'horloge QS est une horloge astronomique de premier ordre pour

l'économie d'énergie des éclairages et des stores et rideaux, qui s'intègre

harmonieusement avec les composants de Lutron Energi Savr Node et les

stores et rideaux QS.

Numéro de Modèle : QSGR-TC-3S-WH

Valeurs nominales : 120 –240 V~ 50 / 60 Hz 100 mA

Sortie : 24 V- 150 mA IEC PELV/NEC® Class 2 alimentation

Contenu

Caractéristiques et fonctions .............2

Câblage d’alimentation secteur ...........3

Raccordements ........................3

Détails du câblage d’alimentation secteur ...4

Aperçu du câblage IEC PELV/NEC® Class 2 . 5

Câblage du bus QS .....................6

Compléter de l’installation ...............8

Mode de programmation ................9

Fonctionnement de l'horloge

Réglage Temps et Date ................10

Réglage Endroit ......................11

Réglage Heure Avancée ...............11

Ajouter un Événement .................12

Supprimer / Visualiser un événement ......13

Régler / Visualiser / Supprimer

un Jour férié ........................14

Copier / Supprimer une Cédule ..........15

Dépistage de défauts ..................16

Garantie, Information de contact .........18

Pour connaître les fonctionnalités supplémentaires et

les fonctions avancées, consultez le guide complet

d’installation et d’utilisation (no de pièce032383) sur

www.lutron.com

®

Français

Guide rapide d’installation et de fonctionnement l'horloge QS 2

®

OK

12

3

4

5

6

Écran d’information

Affiche les fonctions de

programmation

Touches programme

Groupes de bouton pour

Stores (traitements de

fenêtres)

Boutons de rappel et

d’ajustement de niveau avec

DEL intégrées (maximum de

3 groupes de boutons)

Bouton d’horloge

Affiche l’information

courante de l’horloge

Bouton OK

Utilisée pour la

programmation,

navigation

USB type mini B

Pour programmer à l’aide

d’un PC

Caractéristiques et fonctions

La pagina sta caricando ...

Lutron Electronics QS Timeclock Quick Installation And Operation Manual

Questo manuale è adatto anche per

Lutron Electronics QS Timeclock Quick Installation And Operation Manual

in altre lingue

Documenti correlati

Altri documenti