Sanyo MDF-U74VC Manuale utente

- 46 -

MDF-U74

V

MDF-U74VC

MDF-U54V

MDF-U54VC

Ultra-Low Temperature Freezer

INSTRUCTION MANUAL

MDF-U74V

- 47 -

1

CONTENTS

INTRODUCTION P. 2

PRECAUTIONS FOR SAFE OPERATION P. 3

ENVIRONMENTAL CONDITIONS P. 7

FREEZER COMPONENTS P. 8

Control panel P. 10

INSTALLATION SITE P. 11

INSTALLATION P. 12

START-UP OF UNIT P. 13

CHAMBER TEMPERATURE SETTING P.14

KEY LOCK FUNCTION P. 14

ALARM TEMPERATURE SETTING P. 15

SETTING OF ALARM RESUME TIME P. 16

REMOTE ALARM TERMINAL P. 17

MONITOR OF FREEZER STATUS P. 18

CHANGE OF COMPRESSOR DELAY TIME P. 19

CHANGE OF DOOR ALARM DELAY TIME P. 20

ALARMS & SAFETY FUNCTIONS P. 21

ROUTINE MAINTENANCE

Cleaning of cabinet P. 22

Cleaning of condenser filter P. 22

Defrosting of inside wall P. 23

TROUBLESHOOTING P. 24

REPLACEMENT OF BATTERY P. 25

DISPOSAL OF UNIT P. 26

Recycle of battery P. 26

TEMPERATURE RECORDER (OPTION) P. 31

BACK-UP SYSTEM (OPTION) P. 32

INNER DOOR (OPTION) P. 33

DRAWER (OPTION) P. 33

MOUNTING OF INTERFACE BOARD (OPTION) P. 34

MOUNTING OF LAN INTERFACE BOARD (OPTION) P. 35

INVENTORY RACK (OPTION) P. 36

SPECIFICATIONS P. 37

PERFORMANCE P. 39

SAFETY CHECK SHEET P. 40

- 48 -

2

INTRODUCTION

Ŷ Read this manual carefully before using the appliance and follow the instructions for safety operation.

Ŷ Sanyo never guarantee any safety if the appliance is used for any objects other than intended use or

used by any procedures other than those mentioned in this manual.

Ŷ Keep this manual in an adequate place to refer to it as necessary.

Ŷ The contents of the manual will be subjected to change without notice due to the improvement of

performance or functions.

Ŷ Contact Sanyo sales representative or agent if any page of the manual is lost or page order is incorrect.

Ŷ Contact Sanyo sales representative or agent if any point in this manual is unclear or if there are any

inaccuracies.

Ŷ No part of this manual may be reproduced in any form without the expressed written permission of

Sanyo.

CAUTION

SANYO guarantees the product under certain warranty conditions. SANYO in no way shall be

responsible for any loss of content or damage of content.

- 49 -

3

PRECAUTIONS FOR SAFE OPERATION

It is imperative that the user complies with this manual as it contains

important safety advice.

Items and procedures are described so that you can use this unit correctly and safely.

If the precautions advised are followed, this will prevent possible injury to the user and

any other person.

Precautions are illustrated in the following way:

WARNING

Failure to observe WARNING signs could result in a hazard to personnel

possibly resulting in serious injury or death.

CAUTION

Failure to observe CAUTION signs could result in injury to personnel and

damage to the unit and associated property.

Symbol shows;

㩷

this symbol means caution.

㩷

this symbol means an action is prohibited.

㩷

this symbol means an instruction must be followed.

Be sure to keep this manual in a place accessible to users of this unit.

Some warning and/or caution labels are attached on the unit. Following shows the description of such

labels.

This label is on the cover in which the electrical components of high voltage are

enclosed to prevent the electric shock. The cover should be removed by a qualified

engineer or a service personnel only.

This symbol means attention or refer to document.

This symbol means earth.

This symbol means power switch “ON”.

This symbol means power switch “OFF”.

WARNING

As with any equipment that uses CO

2

gas, there is a likelihood of oxygen depletion in the vicinity

of the equipment. It is important that you assess the work site to ensure there is suitable and

sufficient ventilation. If restricted ventilation is suspected, then other methods of ensuring a

safe environment must be considered. These may include atmosphere monitoring and warning

devices.

- 50 -

4

PRECAUTIONS FOR SAFE OPERATION

Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to

rain water.

Only qualified engineers or service personnel should install the unit. The installation by

unqualified personnel may cause electric shock or fire.

Install the unit on a sturdy floor and take an adequate precaution to prevent the unit from

turning over. If the floor is not strong enough or the installation site is not adequate, this may result

in injury from the unit falling or tipping over.

Never install the unit in a humid place or a place where it is likely to be splashed by water.

Deterioration of the insulation may result which could cause current leakage or electric shock.

Never install the unit in a flammable or volatile location. This may cause explosion or fire.

Never install the unit where acid or corrosive gases are present as current leakage or electric

shock may result due to corrosion.

Always ground (earth) the unit to prevent electric shock. If the power supply outlet is not

grounded, it will be necessary to install a ground by qualified engineers.

Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such

grounding may cause electric shock in the case of an incomplete circuit.

Connect the unit to a power source as indicated on the rating label attached to the unit. Use

of any other voltage or frequency other than that on the rating label may cause fire or electric shock.

Never store volatile or flammable substances in this unit if the container cannot be sealed. These

may cause explosion or fire.

Do not insert metal objects such as a pin or a wire into any vent, gap or any outlet on the unit.

This may cause electric shock or injury by accidental contact with moving parts.

Use this unit in safe area when treating the poison, harmful or radiate articles. Improper use

may cause bad effect on your health or environment.

Turn off the power switch (if provided) and disconnect the power supply to the unit prior to any

repair or maintenance of the unit in order to prevent electric shock or injury.

Do not touch any electrical parts (such as power supply plug) or operate switches with a wet

hand. This may cause electric shock.

WARNING

- 51 -

5

PRECAUTIONS FOR SAFE OPERATION

Ensure you do not inhale or consume medication or aerosols from around the unit at the time of

maintenance. These may be harmful to your health.

Never splash water directly onto the unit as this may cause electric shock or short circuit.

Never put containers with liquid on the unit as this may cause electric shock or short circuit when

the liquid is spilled.

Never bind, process, or step on the power supply cord, or never damage or break the power

supply plug. A broken supply cord or plug may cause fire or electric shock.

Do not use the supply cord if its plug is loose. Such supply cord may cause fire or electric shock.

Never disassemble, repair, or modify the unit yourself. Any such work carried out by an

unauthorized person may result in fire, or electric shock or injury due to a malfunction.

Disconnect the power supply plug if there is something wrong with the unit. Continued

abnormal operation may cause electric shock or fire.

When removing the plug from the power supply outlet, grip the power supply plug, not the cord.

Pulling the cord may result in electric shock or fire by short circuit.

Disconnect the power supply plug before moving the unit. Take care not to damage the power

cord. A damaged cord may cause electric shock or fire.

Disconnect the power plug when the unit is not used for long periods. Keeping the connection

may cause electric shock, current leakage, or fire due to the deterioration of insulation.

If the unit is to be stored unused in an unsupervised area for an extended period, ensure that

children do not have access and that doors cannot be closed completely.

The disposal of the unit should be accomplished by appropriate personnel. Remove doors to

prevent accidents such as suffocation.

Do not put the packing plastic bag within reach of children as suffocation may result.

WARNING

- 52 -

6

PRECAUTIONS FOR SAFE OPERATION

Use a dedicated power source (a dedicated circuit with a breaker) as indicated on the rating label

attached to the unit. A branched circuit may cause fire resulting from abnormal heating.

Connect the power supply plug to the power source firmly after removing the dust on the plug.

A dusty plug or improper insertion may cause a heat or ignition.

Never store corrosive substances such as acid or alkali in this unit if the container cannot be

sealed. These may cause corrosion of inner components or electric parts.

Check the setting when starting up of operation after power failure or turning off of power

switch. The stored items may be damaged due to the change of setting.

Be careful not to tip over the unit during movement to prevent damage or injury.

Prepare a safety check sheet when you request any repair or maintenance for the safety of service

personnel.

CAUTION

- 53 -

7

ENVIRONMENTAL CONDITIONS

This equipment is designed to be safe at least under the following conditions (based on the IEC 61010-1):

Ŷ Indoor use;

Ŷ Altitude up to 2000 m;

Ŷ Ambient temperature 5

o

C to 40

o

C

Ŷ Maximum relative humidity 80% for temperature up to 31

o

C decreasing linearly to 50% relative humidity

at 40

o

C;

Ŷ Mains supply voltage fluctuations not to exceed 㫧10% of the nominal voltage;

Ŷ Other supply voltage fluctuations as stated by the manufacturer;

Ŷ Transient overvoltages according to Installation Categories (Overvoltage Categories) II; For mains

supply the minimum and normal category is II;

Ŷ Pollution degree 2 in accordance with IEC 60664.

- 54 -

8

FREEZER COMPONENTS

11(inside)

7 (inside)

16

17

15

14

Rear side

1

2

3

6

8

12

7

4

9

10

13

5

Power cord

16

17

15

- 55 -

9

FREEZER COMPONENTS

1. Control panel (on the upper front of the door): Used for temperature setting and indication of

operating status is displayed on the panel. See page 10 for details.

2. Outer door: To open the door, grip the handle. On closing, lock the outer door latch completely.

3. Inner door: The operation of the inner door should be quick to minimize the temperature rise in

chamber. Lock the inner door latch completely when the door is closed. The door is removable for

cleaning or defrosting. See page 23 “Routine maintenance”.

4. Outer door latch: Always lock the latch when the outer door is closed.

5. Inner door latch: Always lock the inner door latch when the inner door is closed.

6. Magnetic door gasket: This provides a tight door seal and prevents cold air leak. Keep clean.

7. Access port (rear and bottom): This is used for leading a cable and sensor of a measuring

equipment, or nozzle of back-up system to chamber.

8. Air intake vent (grille): Do not block this vent to keep the proper cooling performance.

9. Caster: 4 casters are provided to facilitate moving of the cabinet. For the installation, adjust the

leveling foot so that the front 2 casters cannot contact with the floor.

10. Leveling foot: The height of the freezer can be adjusted by this screw type foot. Keep the unit in

level at the installation.

11. Condenser filter (behind the grille): This filter prevents the dust from accumulating on the

condenser. The dusty filter may cause failure of refrigerating device. Clean the filter once a month.

See page 22 “Routine maintenance” for the cleaning.

12. Space for temperature recorder: An automatic temperature recorder (optional component) can be

attached here. See page 31“ Temperature recorder (Option)”.

13. Key lock: Turn clockwise to 180

o

with a key and the outer door is securely locked.

14. Fixture (on back side): 2 fixtures are provided as spacers between the cabinet and wall and also

serve as hooks to fix the unit. See page 12 “Installation”.

15. Power switch: This is for turning ON/OFF the power to the unit. ON – “I” OFF – “٤”

16. Remote alarm terminal: This is used to notice an alarm condition of the unit to remote location.

Refer to page 17 “Remote alarm terminal”.

17. Battery switch: This is a switch for a battery for power failure alarm. Normally, turn on this switch.

Be sure to turn off this switch if the freezer is not in operating for the long period (over one month).

18. Space for optional component:

19. Door switch: This switch detects the open/close status of outer door.

- 56 -

10

FREEZER COMPONENTS

Control panel

1. Digital temperature indicator: This indicator shows the present chamber temperature or set

temperature.

2. Status monitor lamp (STATUS): This lamp lights when environmental condition or status gets worse

or the unit is out of normal operation.

3. Battery check lamp (BATTERY): This lamp lights to recommend the battery replacement. This lamp

blinks when a fan motor is maintained. For the replacement, consult Sanyo sales representative or agent.

4. Door check lamp (DOOR): This lamp lights when the door is open.

5. Alarm lamp (ALARM): This lamp is flashed during alarm condition.

6. Filter check lamp (FILTER): This lamp lights when the excessive dust is accumulated on the

condenser filter. When this lamp lights, clean the condenser filter following the procedure on page 22.

7. Numerical value shift key ( ): Pressing this key in the setting mode causes the numerical value to

shift. “ON-OFF” of key lock can be selected by pressing this key in the key lock mode. By pressing this

key for more than 5 seconds in the temperature display mode leads setting mode for alarm temperature,

alarm resume time ,compressor delay time and door alarm delay time. Refer to page 14,15,16,19 and

20 for details respectively.

8. Digit shift key ( ): Pressing this key in the setting mode causes the changeable digit to shift. Key

lock is available by pressing this key for more than 5 seconds in the temperature display mode. Refer to

page 14 for details.

9. Set key (SET): Temperature setting mode is led by pressing this key and the changeable digit is

flashed. By pressing this key again, the setting is memorized. The set mode returns to the temperature

display mode automatically when 90 seconds has passed without any key operation. Refer to page 14

for details.

10. Status key (STATUS): By pressing this key in the event of the status monitor lamp ON, the status

code is displayed on the digital temperature indicator. This key is not effective when the freezer is

running normally. See page 18 for details.

11. Alarm test key (ALARM TEST): To check the alarm system during freezer operation. Pressing

this key with the battery switch ON gets the alarm lamp to flash, the remote alarm to operate, and the

buzzer to sound.

12. Buzzer stop key (BUZZER): To silence the audible alarm under alarm condition, press this key.

The buzzer during alarm test cannot be silenced by this key.

12

ULTRA LOW

BATTERY

STATUS

FILTER

A

LARM

DOOR

TEMPERATURE

(

o

C

)

BUZZER

ALARM

TEST

STATUS SET

11 10 9 8

7

1 32 654

- 57 -

11

INSTALLATION SITE

To operate this unit properly and to obtain maximum performance, install the unit in a location with the

following conditions:

Ŷ A location not subjected to direct sunlight

Do not install the unit under direct sunlight. Installation in a location subjected to direct sunlight cannot

obtain the intended performance.

Ŷ A location with adequate ventilation

Leave at least 10 cm around the unit for ventilation. Poor ventilation will result in a reduction of the

performance and consequently the failure.

Ŷ A location away from heat generating sources

Avoid installing the unit near heat-emitting appliances such as a heater or a boiler etc. Heat can

decrease the intended performance of the unit.

Ŷ A location with little temperature change

Install the unit under stable ambient temperature. The allowable ambient temperature is between +5

and +30

o

C.

Ŷ A location with a sturdy and level floor

Always install the unit on a sturdy and level floor. The uneven floor or tilted installation may cause failure

or injury. Install the unit in stable condition to avoid the vibration or noise. Unstable condition may

cause vibration or noise.

WARNING

Install the unit on a sturdy floor. If the floor is not strong enough or the installation site is not

adequate, this may result in injury from the unit falling or tipping over.

Select a level and sturdy floor for installation. This precaution will prevent the unit from tipping.

Improper installation may result in water spillage or injury from the unit tipping over.

Ŷ A location not prone to high humidity

Install the unit in the ambient of 80% R.H. or less humidity. Installation under high humidity may cause

current leakage or electric shock.

WARNING

Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to

rain water.

Never install the unit in a humid place or a place where it is likely to be splashed by water.

Deterioration of the insulation may result which could cause current leakage or electric shock.

Ŷ A location without flammable or corrosive gas

Never install the unit in a flammable or volatile location. This may cause explosion or fire or may result

in the current leakage or electric shock by the corrosion of the electrical components.

Ŷ A location without the possibility of anything fall

Avoid installing the unit in the location where anything can fall down onto the unit. This may cause the

breakdown or failure of the unit.

- 58 -

12

INSTALLATION

1. Removing the packaging materials and tapes

Remove all transportation packaging materials and tapes. Open the doors and ventilate the unit. If the

outside panels are dirty, clean them with a diluted neutral dishwashing detergent. (Undiluted detergent

can damage the plastic components. For the dilution, refer to the instruction of the detergent.) After

the cleaning with the diluted detergent, always wipe it off with a wet cloth. Then wipe off the panels with

a dry cloth.

2. Adjusting the leveling foot

Extend the leveling feet by rotating them counterclockwise to contact them to the floor. Ensure the unit

is level. (Fig. 1)

3. Fixing the unit

Two fixtures are attached to the rear of the frame. Fix the frame to the wall with these fixtures and rope

or chain. (Fig. 2)

4. Ground (earth) (Except for USA and CANADA)

The ground (earth) is for preventing the electric shock in the case of the electrical insulation is somehow

degraded. Always ground the unit at the time of installation.

WARNING

Use a power supply outlet with ground (earth) to prevent electric shock. If the power supply outlet is

not grounded, it is necessary to install a ground by qualified engineers.

Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such

grounding may cause electric shock in the case of an incomplete circuit.

Leveling foot

Fig.1

Fixture

Fig. 2

- 59 -

13

START-UP OF UNIT

Follow the procedures for the initial and consequent operations of the unit.

1. Turn off the switch of the back-up system (optional component) if it is installed.

2. Connect the power supply cord to the dedicated outlet having appropriate rating with the chamber

empty, and turn on the power switch on the freezer.

3. Turn on the battery switch.

4. Set the desired chamber temperature. See page 14 for the temperature setting.

5. Check that the chamber temperature reaches the desired temperature.

6. Turn on the switch of back-up system (optional component) if it is installed.

7. Make sure that the alarm lamp blinks and the buzzer sounds by pressing the alarm test key (ALARM

TEST). The remote alarm is also operated. E09 is displayed on the digital temperature indicator if the

battery switch is OFF. Make sure to turn on the battery switch.

8. After confirming the above, you can put articles into the freezer chamber in a small batch to prevent the

temperature rise.

9. An alarm function is to work normally, or push and confirm an alarm test key (the condition that a

battery switch is on). It is normal if alarm lamp blinking, remote alarm operation and a buzzer ring.

Operation after power failure

The set value is memorized by nonvolatile memory. Accordingly, the freezer resumes the operation with

setting before power failure.

When the freezer is recovered from power failure with the chamber temperature higher than the preset

temperature, then the high temperature alarm is activated and the buzzer sounds and the remote alarm is

also activated. Please push the buzzer stop key (BUZZER) to silence buzzer and take appropriate

actions if needed.

- 60 -

14

CHAMBER TEMPERATURE SETTING

Table 1 shows the basic procedure for setting the chamber temperature. Perform key operations in the

sequence indicated in the table. The example in the table is based on the assumption that the desired

temperature is -75

o

C.

Note: The unit is set at the factory that the chamber temperature -80

o

C.

Table 1. Basic operation sequence (Example: Chamber temperature -75

o

C)

Description of operation Key operated Indication after operation

1

Turn the power switch ON.

----

The current chamber temperature is

displayed.

2 Press set key. SET

The second digit is flashed.

When pressed, the figure of settable

digit changes.

3

Set to -75 with the numerical value

shift key and digit shift key.

When pressed, the settable digit

is shifted.

4 Press set key. SET

Set temperature is memorized and the

current chamber temperature is

displayed.

Note:

• The temperature set mode returns to the temperature display mode automatically when 90 seconds has

passed without any key operation.

• Although the value of the chamber temperature setting can range from -50

o

C to -90

o

C, the guaranteed

temperature when there is no load is -86

o

C when the ambient temperature is 30

o

C.

KEY LOCK FUNCTION

This unit is provided with the key lock function. When the key lock is ON, change of temperature setting

through the key pad is not available. The key lock is set in OFF at the factory.

Display Mode Function

L 0 Key lock is OFF Enable to change of temperature setting

L 1 Key lock is ON Disable to change of temperature setting

Table 2. Procedure for key lock setting (change from key lock OFF to key lock ON)

Description of operation Key operated Indication after operation

1 ----

The current chamber temperature is

displayed.

2 Press digit shift key for 5 seconds. The first digit is flashed.

3

Press numerical value shift key

and scroll the figure to 1.

When pressed, the figure of settable

digit changes.

4 Press set key. SET

The key lock is set to ON.

The current chamber temperature is

displayed.

• The temperature set mode returns to the temperature display mode automatically when 90 seconds has

passed without any key operation.

- 61 -

15

ALARM TEMPERATURE SETTING

This unit is provided with the high and low temperature alarm and the temperature at which the alarm is

activated is changeable.

The following procedure shows the setting of alarm temperature according to the condition below:

High temperature alarm: activates at the temperature 5

o

C higher than the set temperature

Low temperature alarm: activates at the temperature 5

o

C lower than the set temperature

Note:

The alarm temperature is set at the factory 10

o

C higher and lower than the set temperature.

The available range of alarm temperature is between 5

o

C and 20

o

C higher or lower than the set

temperature.

Table 3. Procedure for setting high temperature alarm

Description of operation Key operated Indication after operation

1 ----

The current chamber temperature is

displayed.

2

Press numerical value shift key for

about 5 seconds.

The first digit is flashed.

3

Press numerical value shift key

and scroll the figure to 1.

The first digit is flashed.

4 Press set key. SET The first digit is flashed.

When pressed, the figure of settable

digit changes.

5

Scroll the figure to 005 by using

digit shift key and numerical value

shift key

When pressed, the changeable digit

moves.

6 Press set key. SET

Alarm temperature is memorized and

the current chamber temperature is

displayed.

Table 4. Procedure for setting low temperature alarm

Description of operation Key operated Indication after operation

1 ----

The current chamber temperature is

displayed.

2

Press numerical value shift key for

about 5 seconds.

The first digit is flashed.

3

Press numerical value shift key

and scroll the figure to 2..

The first digit is flashed.

4 Press set key. SET

The first digit is flashed.

When pressed, the figure of settable

digit changes.

5

Scroll the figure to -05 by using

digit shift key and numerical value

shift key

When pressed, the changeable digit

moves.

6 Press set key. SET

Alarm temperature is memorized and

the current chamber temperature is

displayed.

• The temperature set mode returns to the temperature display mode automatically when 90 seconds has

passed without any key operation.

- 62 -

16

SETTING OF ALARM RESUME TIME

The alarm buzzer is silenced by pressing buzzer stop key (BUZZER) on the control panel during alarm

condition (The remote alarm is not silenced).

The buzzer will be activated again after certain suspension if the alarm condition is continued. The

suspension time can be set by following the procedure shown in the Table 5 below.

The example in the table is based on the assumption that the desired duration is 20 minutes.

Note: The duration is set in 30 minutes at the factory.

Table 5. Setting procedure for alarm resuming time (change from 30 minutes to 20 minutes)

Description of operation Key operated Indication after operation

1 ----

The current chamber temperature is

displayed.

2 Press digit shift key for 5 seconds. The first digit is flashed.

The settable digit is shifted.

3

Set the figure to F25 with the digit

shift key and numerical value shift

key.

When pressed, the figure of settable

digit changes.

4 Press set key. SET

The current resume time is displayed.

The second digit is flashed.

5

Set the figure to 020 with the

numerical value shift key.

When pressed, the figure of settable

digit changes.

6 Press set key. SET

The setting is memorized and

the current chamber temperature is

displayed.

• The settable alarm resume time is 10, 20, 30, 40, 50, or 60 minutes (The setting is 010, 020, 030, 040,

050, or 060). The buzzer would not resume if the resume time is set in 000.

• It is recommended to set the alarm resume time when the freezer is not under alarm condition. The

setting during alarm condition is effective on the next alarm condition.

• The setting cannot be changed during power failure.

• The remote alarm during power failure or buzzer and remote alarm during alarm test cannot be silenced.

• The set mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation. In this case, any setting before pressing set key (SET) is not memorized.

- 63 -

17

REMOTE ALARM TERMINAL

The terminal of the remote alarm is installed at the lower left side of the unit. The alarm is outputted from

this terminal. Contact capacity is DC 30 V, 2 A.

Contact output:

between COM. and N.O. between COM. and N.C.

At normal Open Close

At abnormal Close Open

Note:

The alarm is actuated when the power cord is disconnected from the outlet or the power switch is OFF.

REMOTE ALARM

N.C. COM N.O.

MAX DC30V 2A

- 64 -

18

MONITOR OF FREEZER STATUS

The freezer has a function to monitor the running status of the unit as shown in table 6 below. This is to

notice the running status getting worse (not failure).

1. The status monitor lamp is lit when one of the running status shown in table 6 is detected.

2. The S code (--X, X: 1 to 3) is displayed on the temperature indicator by pressing STATUS key when

the STATUS lamp is lit.

3. Pressing the STATUS key again returns to current chamber temperature on the temperature indicator.

(The indication returns to the chamber temperature display automatically when no key is operated for 90

seconds.)

Table 6. Monitor of running status

Kind of

function

Status Indication

If this status

continues

Remedy

Notice of

abnormal

ambient

temperature

When the ambient

temp. is over approx.

35

o

C or lower than

about 0

o

C.

STATUS lamp

lights.

“--1” is displayed.

Decrease of cooling

performance or

durability of

refrigerating circuit.

Recheck air-

conditioning of

installed site.

Notice of low

voltage

When the power

source voltage is

less than approx.

195 V when the rated

voltage is between

220 and 240 V.

STATUS lamp

lights.

“--2” is displayed.

Abnormal heat at

power supply outlet

or degrade of

starting performance

of refrigerating

circuit

Use dedicated

power source.

Notice of

overload

condition

When the running

rate of refrigerating

Circuit is higher than

usual.

STATUS lamp

lights.

“--3” is displayed.

Decrease of cooling

performance or

durability of

refrigerating circuit.

1. This is likely to

happen when a

large amount of

materials is stored.

2. Check ambient

temp., voltage, and

sealing of

outer/inner door.

Note:

• The S code displayed on the temperature indicator is changed every few seconds if two or three status

shown in the above table are detected at the same time. 㧔--1 Ј --2 Ј --3 Ј --1 repeated㧕

• The monitoring function does not trigger a buzzer or conduct a safety operation.

the case of multiple indication of S code, follow the remedy for each status.

• The status monitor lamp (STATUS) may be lit under normal running condition when the independent

inner door (MDF-U54V:MDF-5ID, MDF-U74V:MDF-7ID) is installed because of less cooling performance.

In this case, adjust the air conditioning so that the ambient temperature is around 23

o

C, or set the

chamber temperature 10

o

C higher than the current setting.

• The set mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation.

- 65 -

19

CHANGE OF COMPRESSOR DELAY TIME

The delay time of high and low stage side compressor can be changed to reduce the load on the power

line and to facilitate the start-up (reset) of the freezer after power failure.

The example in the table 7 is based on the assumption that the delay time is changed to 4 minutes.

(The delay time is set in 3 minutes at the factory.)

Note:

• The delay time should be the same for high stage side and low stage side compressors.

• The setting range for delay time is between 3 and 15 minutes. The cool down of chamber temperature

may be slow when the setting of delay time is over 5 minutes, depending on the installation environment.

There is no need of changing the delay time when the capacity of power source is adequate.

Table 7. Changing procedure for delay time (change from 3 minutes to 4 minutes)

Description of operation Key operated Indication after operation

1 ----

The current chamber temperature is

displayed.

2

Press numerical value shift key for

5 seconds.

The first digit is flashed.

3

Set the figure to F05 with the

numerical value shift key.

When pressed, the figure of settable

digit changes.

4 Press set key. SET

The current delay time is displayed.

The first digit is flashed.

5

Set the figure to 004 with the

numerical value shift key.

When pressed, the figure of the first

digit changes.

6 Press set key. SET

The delay time is memorized and

the current chamber temperature is

displayed.

• The compressor starts to operate with the delay time set by the above procedure at the time of power on

or after power failure. However, the start up of the low stage side compressor is affected by the

chamber temperature and the cascade condenser temperature. The delay time varies depending on

how they meet the start up conditions. It is more than four minutes in case of the above example.

• The set mode returns to the temperature display mode automatically when 90 seconds has passed

without any key operation.

La pagina si sta caricando...

Sanyo MDF-U74VC Manuale utente

Questo manuale è adatto anche per

Sanyo MDF-U74VC Manuale utente

in altre lingue

Documenti correlati

Altri documenti