Sovereign 01016 Istruzioni per l'uso

Marca: Sovereign

Modello: 01016

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

SBV 3200

Operating Instructions

Petrol Blower Vac

SBV 3200

34.360.03

Art.-No.: 519920 I.-Nr.: 01016

Anleitung SBV 3200:_ 22.11.2006 11:13 Uhr Seite 1



Please read these instructions carefully

before installing and operating the

petrol blower vac!

Petrol Engine Quick Start Guide

Ensure correct fuel/oil mixture 40:1

STARTING

1. In “Vac” position, the collecting bag must be

attached to unit firmly. In “Blower” position,

the Vacuum/Blower slide has to be pulled to

the end position.

2. Pull the throttle trigger until auto locked.

3. Pump the “Primer Bulb” 10 times.

4. Move the choke lever to “ START”

position.

Note - the amount of Choke will vary slightly

depending on the weather conditions, a

small amount of experimentation is advised.

5. Grip handle firmly.

6. Pull starter rope briskly 4 times or until

engine tries to start.

7. Warm engine for 10 seconds.

8. After warm-up move choke lever to “ RUN”

position.

Note - this quick start guide is intended for

experienced users who have already

assembled the tool, please refer to the

manual for details.

If machine does not start after minimum 6 pulls

on starter cord refer to petrol Engine Q & A on

page 16.

Anleitung SBV 3200:_ 22.11.2006 11:13 Uhr Seite 2

11 12

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 3

1A 1B

4D 4E

4B 4C

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 4

5 6

.025 in.

(0,6 mm)

7A 7B 8 9

12 3 4 5

678910

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 5

Table of contents Page

1. General safety regulations 7

2. Machine layout and items supplied 8

3. Technical data 8

4. Intended use 8

5. Environmental protection 9

6. Assembly 9

7. Before starting the machine 9

8. Operation 9

9. Maintenance 11

10. Storage 11

11. Disposal 12

12. Ordering replacement parts 12

13. Troubleshooting 12

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 6

When using equipment, a few safety precautions

must be observed to avoid injuries and damage.

Read the operating instructions carefully and

comply with them. It is important to consult these

instructions in order to acquaint yourself with the

unit, its proper use and safety regulations.

Keep this manual in a safe place, so that the

information is available at all times.

If you give the equipment to any other person,

hand over these operating instructions as well.

We accept no liability for damage or accidents

which arise if these instructions have not been

adhered to.

1. GENERAL SAFETY REGULATIONS

Explanation of the information signs on the

machine (Fig. 10)

1. Read the operating instructions before you use

the blower vac.

2. Wear helmet, ear muffs and goggles!

3. Warning! Hazard!

4. Keep other people away.

5. Warning! Hot surface.

6. Fuel pump.

7. Never work if people – especially children - or

animals are in the danger area.

8. Never allow the blower to run without the blower

tube.

9. Sound power level with EC Directive

2000/14/EC!

10. After the unit is switched off, the motor continues

to run for a short while.

Note

1. WEAR CLOSE FITTING, TOUGH WORK

CLOTHING that will provide protection/without

restricting your movements, such as long slacks

or trousers, safety work shoes, heavy duty work

gloves, hard hat, a safety face shield, or safety

glasses for eye protection and a good grade of

ear plugs or other sound barriers for hearing

protection.

2. REFUEL IN A SAFE PLACE. Open fuel cap

slowly to release any pressure which may have

formed in fuel tank. Always wipe unit of fuel or oil

spills before starting. To prevent a fire hazard,

move at least 10 feet (3 meters) from fueling area

before starting.

3. TURN UNIT OFF before setting it down, and also

before installing or removing attachments.

4. KEEP ALL SCREWS AND FASTENERS TIGHT

and the unit in good operating condition. Never

operate this equipment if it is improperly adjusted

or not completely and securely assembled.

5. KEEP HANDLES DRY, clean and free of fuel

mixture.

6. STORE EQUIPMENT AWAY FROM POSSIBLE

IGNITION SOURCES, such as gas-powered

water heaters, clothes dryers, or oil-fired

furnaces, portable heaters, etc.

7. ALWAYS KEEP the engine free of debris build-

up.

8. OPERATION OF EQUIPMENT should always be

restricted to mature and properly instructed

individuals.

9. ALL PERSONS WITH RESPIRATORY

PROBLEMS and persons operating blower in

very dusty environments, should wear a dust

particle mask at all times. Paper dust masks are

available at most paint and hardware stores.

10. Use the blower vac only at reasonable times of

the day. Do not use early in the morning or late in

the evening when people could feel disturbed.

Pay attention to your local noise control

regulations.

11. Allow the machine to run at the lowest possible

motor speed required to carry out the work.

12. Before you start work, use a brush and scraper to

remove all dirt from the blower vac.

13. In case of dusty conditions, moisten the surface a

little.

14. Use the full-length blower nozzle extension so

that the air current can work near to the ground.

15. Watch out for children, pets, open windows etc.

and blow the dirt safely away from them.

앬WHAT NOT TO DO

WARNING: DO NOT USE ANY OTHER FUEL than

that recommended in your manual. Always follow

instructions in the Fuel and Lubrication section of this

manual. Never use fuel unless it is properly mixed

with 2-stroke engine lubricant. Permanent damage to

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 7

engine will result, voiding manufacturerʼs warranty.

1. DO NOT SMOKE while refueling or operating

equipment.

2. DO NOT OPERATE UNIT WITHOUT A

MUFFLER and properly installed muffler shield.

3. DO NOT TOUCH or let your hands or body come

in contact with a hot muffler or spark plug wire.

4. DUE TO THE DANGER of exhaust fumes, never

operate blower in a confined or poorly ventilated

area.

5. NEVER POINT BLOWER in the direction of

people, animals, buildings, automobiles, or

windows, etc.

6. DO NOT operate unit without inlet cover installed

to prevent contact with impeller.

7. DO NOT set a hot engine down where flammable

material is present.

8. DO NOT OPERATE UNIT FOR PROLONGED

PERIODS. Rest periodically.

9. DO NOT OPERATE UNIT WHILE UNDER THE

INFLUENCE OF ALCOHOL OR DRUGS.

WARNING: DO NOT ADD, REMOVE OR ALTER

ANY COMPONENTS OF THIS PRODUCT. Doing so

could cause personal injury and/or damage the unit

voiding the manufacturerʼs warranty.

10. DO NOT operate your unit near or around

flammable liquids or gases whether in or out of

doors. An explosion and/or fire may result.

11. DO NOT WEAR loose clothing, scarfs, neck

chains, unconfined long hair, and the like. Doing

so could cause injury associated with objects

being drawn into the rotating parts. Tie up long

hair and fasten it, for example with a head scarf,

cap, helmet, etc.

12. DO NOT refuel a running engine or an engine

that is hot

13. Never allow children to use the blower vac.

2. Machine layout and items supplied

(Fig. 1)

1. Rear Handle

2. Throttle Trigger

3. Throttle Lock

4. On/Off Switch

5. Front Handle

6. Muffler Cover (Exhaust)

7. Fuel Tank Window

8. Fuel Cap

9. Starter Handle

10. Air Filter Cover

11. Vacuum/Blower Tube

12. Choke Lever

13. Spark Plug Wire / Spark Plug

14. Vacuum/Blower Slide

15. Primer Bulb

16. Harness

17. Vacuum Bag

18. Speed Cleaner Head

3. Technical data

Engine 24 cm3

Max. Air Velocity ca. 145 km/h

Max. Air Volume 236 m3/h

Max. Engine Speed 7.800 ± 500 min-1

Collection Bag 55 Litre

Mulching Ratio 10:1

Fuel Capacity 650 ml

Weight 6.4 kg

Maximum Enquine Performance 0.8 kW

Sound power level 108 dB(A)

Sound pressure level at ear 95 dB(A)

Vibration 13.69 m/s2

4. Intended use

This unit is designed to vacuum up debris such as

leaves, small bits of paper, small twigs, weeds, grass

clippings, etc. Do not use this unit for any other

purpose.

Please note that our equipment has not been

designed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 8

5. Environmental protection

Dispose of soiled maintenance material and

operating materials at the appropriate collection

point.

Recycle packaging material, metal and plastics.

6. Assembly

1. Release the screws (A) and remove the screw

(B). Insert blower tube (C) into the blower

housing and replace screw (B). Tighten screws

(A). (Fig. 1A)

2. Insert speed cleaner head (D) to the tube (C).

(Fig. 1B)

앬HARNESS INSTALLATION

Attach the 2 harness clips to the 2 links in the

blower handle. (Fig. 2)

앬VACUUM ATTACHMENT ASSEMBLY

INSTRUCTIONS

To install vacuum bag:

Pull the slide (A) forward and fit bag (B) into the

vacuum housing. (See Fig. 3)

NOTICE: Vacuum bag installation

The vacuum bag connection tube MUST be scurely

and correctly fitted to the vacuum housing (see fig. 3

of the instructions) prior to the operation. To ensure

the tube is in place correctly, first line up with the

indentations either side of the opening. Push the

connector into place and turn to the right until a click

is heard and the unit locks securely.

This is a safety feature and if the connector is not in

place the blower vac will not start.

The vacuum bag can now be fitted over the open end

of the connection tube and secured with the velcro

strap.

7. Before starting the machine

7.1 Fuel and oil

앬FUEL

Use regular grade unleaded fuel mixed with 40:1

custom 2-stroke engine oil for best results.

WARNING:

Never use straight gasoline in your unit.

This will cause permanent engine damage and void

the manufacturerʼs warranty for that product. Never

use a fuel mixture that has been stored for over 90

days.

WARNING: Use only Class I 2-stroke oil suitable for

air-cooled engines.

앬MIXING FUEL

Mix the fuel with 2-stroke oil in a suitable

container. Shake the container to ensure that it is

properly mixed.

앬FUEL AND LUBRICATION

앬RECOMMENDED FUELS

Some conventional fuel are being blended with

oxygenates such as alcohol or an ether

compound to meet clean air standards. Your

engine is designed to operate satisfactorily on

any fuel intended for automotive use including

oxygenated fuel.

8. OPERATION

8.1 STARTING A COLD ENGINE

Fill fuel tank with proper gas and oil mixture. See

Fuel and Lubrication.

Set unit on ground so that it rests on housing feet.

1. Pull the throttle trigger (A). (It will auto lock) Fig.

4A.

2. Prime the carburettor. Pump the primer bulb (C)

10 times (Fig. 4B).

3. Your unit is designed with a 2 position choke (D):

START “ ” and RUN “ ”. Move choke lever to

START “ ” position (Fig. 4C).

4. Grip handle firmly .

5. Pull starter rope out a short way until resistance

is felt (approximately 100mm). Pull starter rope

quickly and evenly until engine starts or attempts

to run.Once engine starts, warm up at full throttle

for 10 seconds and release throttle.

6. Push down the throttle lock (B), the throttle

trigger (A) will back to the nomal position. (Fig.

4A)

7. Move the choke to RUN “ ” position (Fig. 4E).

Fuel and Oil

Mix 40:1

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 9

NOTE: If engine fails to start after repeated attempts,

refer to Troubleshooting section.

NOTE: Always pull starter rope straight out. Pulling

starter at an angle will cause rope to rub against the

eyelet. This friction will cause the rope to fray and

wear more quickly. Always hold starter handle when

rope retracts. Never allow rope to snap back from

extended position. This could cause rope to snag or

fray and also damage the starter assembly.

8.2 STOPPING THE ENGINE

Emergency Stopping Procedure. When it is

necessary to stop blower engine immediately,

DEPRESS the switch to stop.

Normal Stopping Method. For normal stopping,

push down the throttle lock, the throttle trigger will

back to the nomal position and allow engine to return

to idle speed. Then DEPRESS and HOLD the “OFF”

switch until the engine stops completely.

8.3 STARTING A WARM ENGINE (Engine has

been stopped for no more than 15-20

minutes)

1. Pull starter cord again. Engine should start with

ONE or TWO pulls. If engine fails to start after 6

pulls, repeat steps 2 through 6 (see Starting a

cold engine).

2. If engine does not start, or starts and then stops

after 5 cord pulls, follow procedure “STARTING A

COLD ENGINE”.

8.4 BLOWER OPERATIONS (Fig. 5)

Your blower is designed to easily remove debris from

patios, walkways, lawns, bushes, etc., and many

hard to reach areas where debris may accumulate.

WARNING: Because of flying debris, always wear

approved shielded safety glasses or face shield when

operating blower.

Before using your blower, review Safety Precautions

in your User Manual, and all regulations for operation

of the unit. These precautions and regulations are for

your protection.

CAUTION: Hold the blower so that hot exhaust does

not damage clothing and is not inhaled by operator.

DO NOT operate the blower with other people or

animals in the immediate vicinity. Allow a minimum of

30 feet (9 meters) between operator and other

people or animals.

We recommend that a face mask be worn when

operating blower in dusty areas.

Stand away from the debris, at a distance that will

easily allow you to control the direction of blown

debris. Never blow debris in direction of bystanders.

To control velocity of airstream, blower can be

operated at any speed between idle and full throttle.

Experience with the unit will help you determine the

amount of airflow necessary for each application.

8.5 VACUUM OPERATIONS

WARNING: NEVER OPERATE VACUUM WITHOUT

VACUUM BAG PROPERLY ATTACHED, AS

FLYING DEBRIS COULD CAUSE INJURY TO

OPERATOR AND BYSTANDERS. ALWAYS MAKE

SURE VACUUM BAG ZIPPER IS CLOSED BEFORE

OPERATING UNIT.

Do not vacuum hot or burning materials (e.g. hot ash,

glowing cigarettes) from outdoor fireplaces or

barbecue pits. always wait for these materials to be

cool enough. Do not vacuum lighted smoking

material such as discarded cigars or cigarettes. Do

not operate unit near open flame.

CAUTION: This unit is designed to vacuum up debris

such as leaves, small bits of paper, small twigs,

weeds, grass clippings, etc. Do not use this unit for

any other purpose.

Do not attempt to vacuum rocks, broken glass,

bottles, tin cans or other such objects. Damage to

impeller and unit as well as operator injury could

result.

If vacuum tube is level with power unit horizontal,

rocks or large objects may be drawn into tube,

damaging the impeller.

To Operate Vacuum:

1. Follow correct starting procedures as explained

in this manual.

2. Allow engine to return to idle. Put the shoulder

harness on so the strap is over your right

shoulder. Put the vacuum bag strap on so it is

over your left shoulder.

CAUTION: Do not allow shoulder harness to cover,

block, or come in contact with exhaust outlet during

operation. The muffler generates heat and could

burn, melt, or damage harness strap.

3. Place your left hand on the top handle and right

hand on side handle as shown (Fig. 6).

4. Swing unit side to side to vacuum debris.

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 10

CAUTION: To avoid clogging vacuum tube. DO NOT

FORCE OR PLACE SUCTION TUBE INTO A PILE

OF DEBRIS.

9. Maintenance

9.1 VACUUM TUBE CLOGGING

To Unclog Vacuum Tube:

1. Turn engine “OFF”. Promptly compress vacuum

bag while it is still inflated, expelling air out of the

suction tube.

This reverse airflow is usually sufficient to

dislodge most obstructions. If the obstruction

cannot be cleared by compressing vacuum bag,

follow this procedure:

2. Remove and inspect vacuum tubes.

3. Carefully clean out nozzle.

4. Reinstall vacuum tubes.

9.2 AIR FILTER

CAUTION: NEVER operate blower without the air

filter or dust and dirt will be sucked into the engine

and damage it. The air filter must be kept clean. If it

becomes damaged, install a new filter.

To Clean Air Filter:

1. Remove 2 screws (A) holding air filter cover in

place, remove cover (B) and lift filter (C) from

cover (Fig. 7A and B).

2. Wash filter in soap and water. DO NOT USE

FUEL!

3. Air dry filter.

4. Reinstall air filter and air filter cover.

NOTE: Replace filter if frayed, torn, damaged or

unable to be cleaned.

9.3 CARBURETOR ADJUSTMENT

The carburetor was pre-set at the factory for optimum

performance. If further adjustments are necessary,

please take your unit to the nearest professional.

9.4 SPARK PLUG

1. Spark plug gap = 0.025 in. (0.635mm) (Fig. 8).

2. Torque to 105 to 130 inch pounds (12 to 15 Nm).

Connect spark plug boot.

9.5 VACUUM BAG CLEANING

A dirty bag will obstruct airflow, thereby reducing

vacuum efficiency.

To Clean Bag:

1. Detach vacuum bag from unit.

2. Open zipper and remove contents.

3. Turn bag INSIDE OUT and shake vigorously.

This procedure should be performed on a regular

basis.

4. Turn bag RIGHT SIDE OUT, close zipper and

attach to unit.

NOTE: If vacuum bag is unusually dirty, it should be

washed by hand in warm water with a mild detergent.

Rinse thoroughly. Let dry before using.

10. Storage

10.1 Storing a unit

WARNING: Failure to follow these steps may cause

varnish to form in the carburetor and difficult starting

or permanent damage following storage.

1. Perform all the general maintenance

recommended in the Maintenance Section of

your User Manual.

2. Clean outside surface of unit.

3. Drain fuel from the fuel tank.

4. After fuel is drained, start engine.

5. Run engine at idle until unit stops. This will

purge the carburetor of fuel.

6. Allow engine to cool (approx. 5 minutes).

7. Using a spark plug wrench, remove the spark

plug.

8. Pour 1 teaspoon of clean 2-stroke oil into the

combustion chamber (Fig. 9). Pull starter rope

slowly several times to coat internal components.

Replace spark plug.

9. Store unit in a cool, dry place away from any

source of ignition such as an oil burner, water

heater, etc.

10.2 REMOVING A UNIT FROM STORAGE

1. Remove spark plug.

2. Pull starter rope briskly to clear excess oil from

combustion chamber.

3. Clean and gap spark plug or install a new spark

plug with proper gap.

4. Prepare unit for operation.

5. Fill fuel tank with proper fuel / oil mixture. See

Fuel and Lubrication Section.

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 11

PROBLEM PROBABLE CAUSE CORRECTIVE ACTION

Unit wonʼt start or starts but will not run. Incorrect starting procedures. Follow instructions in the User Manual.

Incorrect carburetor mixture adjustment

setting.

Have carburetor adjusted by an Authorized

Service Center.

Fouled spark plug. Clean / gap or replace plug.

Fuel filter plugged. Replace fuel filter.

Debris bag mounting not fitted correctly. Check the debris bag mounting.

Unit starts, but engine has low power. Incorrect lever position on choke. Move to RUN position.

Dirty air filter. Remove, clean and reinstall filter.

Incorrect carburetor mixture adjustment

setting.

Have carburetor adjusted by an Authorized

Service Center.

Engine hesitates.

No power under load.

Incorrect carburetor mixture adjustment

setting.

Have carburetor adjusted by an Authorized

Service Center.

Runs erratically. Incorrectly gapped spark plug. Clean / gap or replace plug.

Smokes excessively. Incorrect carburetor mixture adjustment

setting.

Have carburetor adjusted by an Authorized

Service Center.

Incorrect fuel mixture. Use properly mixed fuel (40:1 mixture).

11.Disposal

Important.

The petrol grass trimmer is made of several different

materials such as metal, liquids and plastics. Take

any defective components and fluids that are no

longer in use to special waste disposal points. Ask

your dealer or your local council.

12. Ordering replacement parts

Please quote the following data when ordering

replacement parts:

Type of machine

Article number of the machine

Identification number of the machine

Replacement part number of the part required

Helpline Numbers:

UK: 0151 649 1500

IRE: 189 094 6244

13. Troubleshooting

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 12

If after trying all of the above procedures please

call the help line for further assistance

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 13

Landau/Isar, den 30.06.2006

Wimmer

Product-Management

Weichselgartner

General-Manager

ISC GmbH

Eschenstraße 6

D-94405 Landau/Isar Konformitätserklärung

Art.-Nr.: 34.360.03 I.-Nr.: 01016 Archivierung: 3436000-02-4160270

Subject to change without notice

EN ISO 14982; KBV V

Petrol blower vac SBV 3200

98/37/EG

73/23/EWG_93/68/EEC

97/23/EG

89/336/EWG_93/68/EEC

90/396/EWG

89/686/EWG

87/404/EWG

R&TTED 1999/5/EG

2000/14/EG:

95/54/EG:

97/68/EG:

LWM = 107 dB; LWA = 108 dB

P = 0,8 kW

e4*97/68SH2G3*2002/88*0109*02

kerklärt folgende Konformität gemäß EU-Richtlinie

und Normen für Artikel

tdeclares conformity with the EU Directive

and standards marked below for the article

pdéclare la conformité suivante selon la

directive CE et les normes concernant l’article

verklaart de volgende conformiteit in overeen-

stemming met de EU-richtlijn en normen voor

het artikel

mdeclara la siguiente conformidad a tenor de la

directiva y normas de la UE para el artículo

Odeclara a seguinte conformidade de acordo

com a directiva CE e normas para o artigo

Uförklarar följande överensstämmelse enl. EU-

direktiv och standarder för artikeln

qilmoittaa seuraavaa Euroopan unionin direkti-

ivien ja normien mukaista yhdenmukaisuutta

tuotteelle

erklærer herved følgende samsvar med EU-

direktiv og standarder for artikkel

Tзаявляет о соответствии товара

следующим директивам и нормам EC

Bizjavljuje sljedeću uskladjenost s odredbama i

normama EU za artikl.

Qdeclarå urmåtoarea conformitate cu linia direc-

toare CE μi normele valabile pentru articolul.

Zürün ile ilgili olarak AB Yönetmelikleri ve

mas∂n∂ sunar.

z‰ËÏÒÓÂÈ ÙËÓ ·ÎﬁÏÔ˘ıË Û˘ÌÊˆÓ›· Û‡ÌÊˆÓ· ÌÂ

ÙËÓ √‰ËÁ›· ∂∂ Î·È Ù· ÚﬁÙ˘Ô ÁÈ· ÙÔ ÚÔ˚ﬁÓ

Cdichiara la seguente conformità secondo la

direttiva UE e le norme per l’articolo

lattesterer følgende overensstemmelse i

henhold til EU-direktiv og standarder for

produkt

jprohlašuje následující shodu podle směrnice

EU a norem pro výrobek.

Aa következő konformitást jelenti ki a termékek-

re vonatkozó EU-irányvonalak és normák

szerint

Xpojasnjuje sledečo skladnost po smernici EU

in normah za artikel.

deklaruje zgodność wymienionego poniżej

artykułu z następującymi normami na

podstawie dyrektywy WE.

Wvydáva nasledujúce prehlásenie o zhode podľa

smernice EÚ a noriem pre výrobok.

eдеклаpиpа следното съответствие съгласно

диpективите и ноpмите на ЕС за пpодукта.

1заявляє про відповідність згідно з Директивою

ЄС та стандартами, чинними для даного товару

deklareerib vastavuse järgnevatele EL direktiivi

dele ja normidele

Gdeklaruoja atitikti pagal ES direktyvas ir normas

straipsniui

izjavljuje sledeçi konformitet u skladu s odred

bom EZ i normama za artikl

HAtbilstības sertifikāts apliecina zemāk minēto preču

atbilstību ES direktīvām un standartiem

SCG

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 14

GUARANTEE CERTIFICATE

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the

unlikely event that your device develops a fault, please contact our service department at the address

shown on this guarantee card. Of course, if you would prefer to call us then we are also happy to offer our

assistance under the service number printed below. Please note the following terms under which guarantee

claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty

rights. We do not charge you for this guarantee.

2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to

the rectification of these defects or replacement of the device. Please note that our devices have not

been designed for use in commercial, trade or industrial applications. Consequently, the guarantee is

invalidated if the equipment is used in commercial, trade or industrial applications or for other

equivalent activities. The following are also excluded from our guarantee: compensation for transport

damage, damage caused by failure to comply with the installation/assembly instructions or damage

caused by unprofessional installation, failure to comply with the operating instructions (e.g. connection

to the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the

device or use of non-approved tools or accessories), failure to comply with the maintenance and safety

regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or

external influences (e.g. damage caused by the device being dropped) and normal wear resulting from

proper operation of the device.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

3. The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee

claims should be submitted before the end of the guarantee period within two weeks of the defect being

noticed. No guarantee claims will be accepted after the end of the guarantee period. The original

guarantee period remains applicable to the device even if repairs are carried out or parts are replaced.

In such cases, the work performed or parts fitted will not result in an extension of the guarantee period,

and no new guarantee will become active for the work performed or parts fitted. This also applies when

an on-site service is used.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by

the scope of this guarantee or for units which are no longer covered. To take advantage of this service,

please send the device to our service address.

Sovereign Customer Helpline 0044 (0) 151 649 1500

 Technical specifications subject to change

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 15



The reprinting or reproduction by any other means, in whole or in part,

of documentation and papers accompanying products is permitted only

with the express consent of ISC GmbH.

EH 11/2006

Anleitung SBV 3200:_ 22.11.2006 11:14 Uhr Seite 16

Sovereign 01016 Istruzioni per l'uso

Marca: Sovereign

Modello: 01016

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

SBV 3200

Scarica PDF

rapporto

in altre lingue

English: Sovereign 01016 Operating instructions

Sovereign 01016 Istruzioni per l'uso

Questo manuale è adatto anche per

Sovereign 01016 Istruzioni per l'uso

in altre lingue

Altri documenti