Aqara Motion Sensor Guida utente

54*67mm

80g

V5

pantone cool gray 11c

Motion Sensor P1User Manual

Bedienungsanleitung für den Bewegungsmelder P1

Manuel d'utilisation du détecteur de mouvement P1

Manual de uso del sensor de movimiento P1

Manuale Utente del Sensore di Movimento P1

Датчик движения P1 Руководство пользователя

모션�센서 P1 사용자�설명서

人體傳感器P1使用說明書

. 01

. 14

. 26

. 39

. 51

. 62

. 73

. 82

01

*

An Aqara Zigbee 3.0 Hub or device with the function of Zigbee 3.0 Hub is

required for use.

If using with Apple HomeKit, an Apple Home Hub is required. Please visit

www.aqara.com/support for more details.

Motion Sensor P1 detects body motion and the state of

ambient light.

If there are any people moving or any change in the ambient

light state in the areas under detection, the motion sensor

will send notice to the Aqara Home app through the

connected Aqara Zigbee 3.0 Hub or link to other devices.

Product Introduction

Reset button

Long press 5s: Reset/Pairing mode

Click: Verification of eﬀective

communication distance/device

searching

Lens (with red/blue dual-color indicator

light inside)

Light detection window

Battery cover

02

*If adding fails, please move the product closer to thehub

and try again.

1.

2.

3.

4.

Before activating the accessory, please make sure you

have the Aqara Home app downloaded and an Aqara

Zigbee 3.0 hub installed.

Remove the insulating pull tab.

Pull the tab out from under the battery contact to the

direction of the arrow to activate the product.

Please open the app, tap “Home” and then tap “+” in the

top right corner to enter the “Add Device (Accessory)”

page. Select “Motion Sensor P1” and add it according to

instructions in the Aqara Home app.

Please see www.aqara.com/support for additional information.

Quick Setup

Please confirm that communication between the motion

sensor and the Aqara Zigbee 3.0 Hub works normally, and

then install and fix it in position.

Installation and Usage

03

1.

2.

3.

4.

Please do not install on tile, glass, marble, or other

smooth and easy-to-moisten objects to avoid the sticker

from loosening.

Please do not install on the surface of a lighting tube or

other high-temperature and heating objects to avoidthe

sticker from loosening.

Please do not install on the surface of wall coverings and

other rough and uneven objects to avoid the sticker from

loosening.

Please do not face it against electrical appliances and

other heating sources to prevent infrared jamming from

causing a false trigger.

Installation Instructions:

Eﬀective detection area--Lateral view

2m

7m4.5m2m0m

04

1.Choose an appropriate installation position and make

sure the installation surface is clean and flat.

Direct Installation

*Recommended installation height is 1.2-2m. The detection scope gets

smaller if it is lower than 1.2m. There will be a blind zone at the bottom of

the motion sensor if it is installed higher than 2m.

Eﬀective detection area--Top view

2.Put the sticker on the bottom of the battery cover,

determine the detection direction, stick it to the desired

installation position, and press hard and evenly for 30 s to

make sure it sticks firmly.

170°

7m

05

3.Stick holder pedestal in the required area, and press hard

and evenly for 30 s to make sure it sticks firmly. In the case

of installing on a wall surface, it is recommended that the

holder gap faces upward to facilitate adjusting detection

direction.

1.Choose an appropriate installation position and make

sure installation surface is clean and flat.

Installation with Holder

2.Stick the sensor to the installation pedestal, and press

hard and evenly for 30 s to make sure it sticks firmly.

06

1.Take oﬀ the battery cover from its gap with screw driver,

and stretch the screw driver into battery compartment

lever opening and take oﬀ the battery compartment.

Battery Replacement

07

2.Install two brand-new CR2450 button batteries into the

battery compartment, with one firmly sticking the

compartment top on the polar front and the other firmly

sticking to the compartment bottom on the polar front.

3.Align to and install the battery compartment based on

arrow directions, and then put on the battery cover.

Alignment of

battery

compartment Alignment of

battery cover

Alignment of

battery cover

Alignment of

battery

compartment

08

Online Customer Service:www.aqara.com/support

Manufacturer:LumiUnited Technology Co., Ltd.

Address: Room 801-804, Building 1, Chongwen Park,

Nanshan iPark, No. 3370, Liuxian Avenue, Fuguang

Community, Taoyuan Residential District, Nanshan District,

ShenzhenChina.

Model:MS-S02

Battery:CR2450

WirelessProtocols:Zigbee 3.0

Dimensions:33.1×33.1×41.6mm

Operating Temperature: -10°C ~ 55°C (14°F ~ 131°F )

Operating Humidity:0~95%RH, no condensation

Zigbee Operation Frequency: 2405-2480 MHz

Zigbee Maximum Output Power ≤ 13 dBm

What is in the Box:Motion Sensor P1 × 1, Holder × 1, Sticker

× 1, User Manual × 1

Product Specifications

1.

2.

This product is not a toy, please keep children away from

this product.

This product is designed for indoor use only. Do NOT use

in humid environments or outdoors.

Warnings

09

Under normal use of condition, this equipment should be

kept a separation distance of at least 20cm between the

antenna and the body of the user.

Hereby, [Lumi United Technology Co., Ltd]

EU Declaration of Conformity

declares that the radio equipment type [Motion Sensor

P1,MS-S02] is in compliance with Directive 2014/53/EU. The

full text of the EU declaration of conformity is available at the

following internet address: https://www.aqara.com/DoC/

Beware of moisture, do NOT spill water or other liquids

onto the product.

Do not place this product near a heat source.

Do not attempt to repair the product by yourself. All

repairs should be performed by authorized personnel.

This product is designed only for improving the

convenience of household life, and for status

notifications. If the user violates the product instructions

and this warning, the manufacturer is not responsible for

any risks and property losses caused thereby.

3.

4.

5.

6.

10

Hereby, [Lumi United Technology Co., Ltd]

UK Declaration of Conformity

declares that the radio equipment type[Motion Sensor

P1,MS-S02] is in compliance with Directive 2017 (SI 2017 No.

1206, as amended by SI 2019 No. 696).

The full text of the UK declaration of conformity is available at

the following internet address: http://www.aqara.com/DoC/.

All products bearing this symbol are waste

electrical and electronic equipment (WEEE as in

WEEE Disposal and Recycling Information

directive 2012/19/EU) which should not be mixed with

unsorted household waste. Instead, you should protect

human health and the environment by handing over your

waste equipment to a designated collection point for the

recycling of waste electrical and electronic equipment,

appointed by the government or local authorities. Correct

disposal and recycling will help prevent potential negative

consequences to the environment and human health.

Please contact the installer or local authorities for more

information about the location as well as terms and

conditions of such collection points.

11

Federal Communications Commission (FCC) compliance

statement:

1.This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired operation.

2.Changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment oﬀ and on, the user is

FCC ID:2AKIT-MSS02

12

encouraged to try to correct the interference by one or

more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and

receiver.

—Connect the equipment into an outlet on a circuit

diﬀerent from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician

for help.

RF Exposure statement:

This equipment complies with FCC radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance of

20 cm between the radiator and your body. This transmitter

must not be co-located or operating in conjunction with any

other antenna or transmitter.

IC NOTICE TO CANADIAN USERS

This device contains licence-exempt transmitter(s)/receiv-

er(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is

subject to the following two conditions:

(1) This device may not cause interference.

IC:22635-MSS02

13

*

Please read this manual carefully and keep it in a safe place.

If necessary, the contents of this manual will be modified or adjusted

without special notice.

Scan to get the Zigbee 3.0 Install Code on the last page of

the manual.

(2) This device must accept any interference, including

interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian

ICES003.

This device complies with RSS247 of Industry Canada.

Operation is subject to the condition that this device does

not cause harmful interference.

This equipment complies with IC radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance of

20 cm between the radiator and your body. This transmitter

must not be co-located or operating in conjunction with any

other antenna or transmitter.

14

*

Für die Verwendung dieses Produkts ist ein Aqara Zigbee 3.0 Hub oder ein

Gerät mit Zigbee 3.0 Hub Funktion erforderlich.

Bei Verwendung mit dem HomeKit ist ein spezielles Modell des Hubs

erforderlich. Weitere Details finden Sie unter www.aqara.com/support.

Bewegungsmelder P1 erfasst Körperbewegungen und den

Zustand des Umgebungslichts.

Wenn sich jemand im Erfassungsbereich bewegt oder sich

der Umgebungslichtzustand ändert,sendet der

Bewegungsmelder eine Benachrichtigung an die Aqara

Home App über den angeschlossenen Aqara Zigbee 3.0 Hub

oder eine Verbindung zu anderen Geräten.

Produktbeschreibung

Reset-Taste

5 s lang drücken: Reset/Netzwerkzugriﬀ

Klick auf: Überprüfung der eﬀektiven

Kommunikationsentfernung/Gerätesuch-

funktion

Batterieabdeckung

Lichterkennungsfenster

Objektiv (mit zweifarbigem

Rot/Blau-Indikator innen)

15

*Wenn das Hinzufügen fehlschlägt, bringen Sie das Produkt

näher an den Hub und versuchen Sie es erneut.

1.

2.

3.

4.

Bevor Sie das Produkt aktivieren, bestätigen Sie bitte,

dass Sie die Aqara Home App heruntergeladen und den

Aqara Zigbee 3.0 Hub installiert haben.

Isolierstreifen entfernen: Aktivieren Sie das Produkt,

indem Sie den Isolierstreifen in Pfeilrichtung unter den

Batteriekontakten herausziehen.

Öﬀnen Sie die App, klicken Sie auf „Home“ und dann auf „+“

in der oberen rechten Ecke, um die Seite „Gerät hinzufügen“

aufzurufen . Wählen Sie "Bewegungsmelder P1" und fügen

Sie gemäß den Anweisungen auf der Seite hinzu.

Für weitere Informationen besuchen Sie bitte

www.aqara.com/support.

Schnelle Einrichtung

Stellen Sie sicher, dass die Kommunikation zwischen dem

Bewegungsmelder und dem Aqara Zigbee 3.0 Hub normal

ist, und installieren und befestigen Sie den

Bewegungsmelder in der Einsatzposition.

Installation und Verwendung

16

1.

2.

3.

4.

Bitte montieren Sie den Bewegungsmelder nicht auf der

Oberfläche von Fliesen, Glas, Marmor oder anderen

glatten und feuchten Objekten, um zu verhindern, dass

sich der Aufkleber löst.

Installieren Sie den Bewegungsmelder nicht auf der

Oberfläche von Lampenröhren oder anderen

hitzebeheizten Objekten, um zu verhindern, dass sich der

Aufkleber löst.

Bitte montieren Sie den Bewegungsmelder nicht auf der

Oberfläche von rauhen und unebenen Gegenständen wie

Wandverkleidungen, um zu verhindern, dass sich der

Aufkleber löst.

Stellen Sie den Bewegungsmelder nicht auf eine

Wärmequelle wie ein elektrisches Gerät, um eine

Fehlauslösung durch Infrarot-Interferenz zu verhindern.

Hinweise zur Installation

La pagina si sta caricando...

Aqara Motion Sensor Guida utente

Aqara Motion Sensor Guida utente

in altre lingue

Documenti correlati

Altri documenti