ADEMCO VISTA-20P Series Manuale utente

Marca: ADEMCO

Modello: VISTA-20P Series

Categoria: Sistemi di controllo accessi di sicurezza

Tipo: Manuale utente

Questo manuale è adatto anche per

K5309-1V1 8/01

9,67$39,67$3&1

9,67$39,67$3&1

6HFXULW\6\VWHPV

VHU

V

XLGH

Technical Manuals Online! - http://www.tech-man.com

– 2 –

IMPORTANT!

PROPER INTRUSION PROTECTION

For proper intrusion coverage, sensors should be located at

every possible

point of entry

to a home or commercial premises. This would include any

skylights that may be present, and the upper windows in a multi-level building.

In addition, we recommend that radio backup be used in a security system so

that alarm signals can still be sent to the Central Monitoring Station in the event

that the telephone lines are out of order (alarm signals are normally sent over

the phone lines).

EARLY WARNING FIRE DETECTION

Early warning fire detection is important in a home. Smoke and heat detectors

have played a key role in reducing fire deaths in the United States. With regard

to the number and placement of smoke/heat detectors, we subscribe to the

recommendations contained in the National Fire Protection Association's

National Fire Alarm Code (NFPA 72). These recommendations can be found on

page 43 of this manual.

$ERXW7KLV0DQXDO

This manual is a step-by-step guide that will acquaint you with the system's

features and benefits. It defines the components and their functions, describes

their operation, and provides clear step-by-step instructions for normal and

emergency procedures. Keep this manual in a convenient place so that you can

refer to it as necessary.

Technical Manuals Online! - http://www.tech-man.com

– 3 –

7DEOHRI&RQWHQW V

System Overview....................................................................................................................5

Introduction ..........................................................................................................................5

System Basics .......................................................................................................................5

About The Keypads................................................................................................................8

General Information.............................................................................................................8

Functions of the Keypads...................................................................................................10

Entry/Exit Delays .................................................................................................................12

Exit Delay............................................................................................................................12

Entry Delay.........................................................................................................................12

Exit Alarms.........................................................................................................................13

Checking For Open Zones..................................................................................................13

Using the [

∗

] Key................................................................................................................13

Arming the System...............................................................................................................14

Stay Mode: Arms Perimeter Only, Entry Delay On.........................................................14

Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones .......................................14

Instant Mode: Arms Perimeter Only, Entry Delay Off....................................................14

Away Mode: Arms Entire System, Entry Delay On.........................................................14

Arming Commands.............................................................................................................15

Single Button Arming ........................................................................................................16

Single-Button “Step” Arming.............................................................................................16

Using the Keyswitch............................................................................................................17

Using the Keyswitch...........................................................................................................17

Disarming and Silencing Alarms......................................................................................18

Using the [OFF] key...........................................................................................................18

Bypassing Protection Zones..............................................................................................19

Using the BYPASS Key......................................................................................................19

Quick Bypass ......................................................................................................................20

Chime Mode...........................................................................................................................20

Viewing Current Date and Time ......................................................................................21

Viewing the Current Date and Time.................................................................................21

Setting the Date and Time.................................................................................................21

Panic Keys..............................................................................................................................22

Using Panic Keys................................................................................................................22

Technical Manuals Online! - http://www.tech-man.com

– 4 –

7DEOHRI&RQWHQWV

Macro Key Programming & Usage...................................................................................23

About Macro Keys...............................................................................................................23

Example of Macro Programming.......................................................................................24

Using a Programmed Macro Key.......................................................................................24

Using Device Commands....................................................................................................25

Paging Feature .....................................................................................................................26

About Automatic Paging ....................................................................................................26

Single Button Paging..........................................................................................................27

Latch Key Paging ...............................................................................................................27

Security Codes & Authority Levels..................................................................................28

About Security Codes .........................................................................................................28

Authority Level Definitions ...............................................................................................28

To assign User Codes and Attributes................................................................................29

Accessing Other Partitions (GOTO Command and Multi-Partition Arming)......30

About Accessing Partitions................................................................................................30

Using the GoTo Command.................................................................................................31

Multi-Partition Arming......................................................................................................31

Common Zone Operation....................................................................................................32

Scheduling .............................................................................................................................33

About Scheduling................................................................................................................33

Creating Schedules.............................................................................................................33

Event Logging Procedures.................................................................................................35

About Event Logging..........................................................................................................35

Viewing the Event Log.......................................................................................................35

Testing the System (To Be Conducted Weekly)............................................................36

Trouble Conditions..............................................................................................................37

Maintaining Your System...................................................................................................40

Fire Alarm System (If Installed).......................................................................................41

Quick Guide to Basic System Functions ........................................................................45

Summary of Audible/Visual Notifications......................................................................46

Regulatory Statements and Warnings............................................................................48

Charts of Your System's Features....................................................................................50

Technical Manuals Online! - http://www.tech-man.com

– 5 –

6\VWHP2YHUYLHZ

,QWURGXFWLRQ

Congratulations on your ownership of an ADEMCO Security System. You've made a wise

decision in choosing it, for it represents the latest in security protection technology today,

and millions of premises are protected by ADEMCO systems. This system provides:

•

Three forms of protection: burglary, fire* and emergency

•

At least one keypad which provides control of system and displays system status

•

Various sensors for perimeter and interior burglary protection

•

Smoke or combustion detectors* designed to provide early warning in case of fire.

Your system may also have been programmed to automatically send alarm or status

messages over the phone lines to a Central Monitoring Station.

* Commercial installations and some residential systems may not include fire

protection – check with your installer.

NOTE: The features and procedures described in this manual apply to both the

VISTA-20P and VISTA-15P security systems. Differences are noted where applicable.

6\VWHP%DVLFV

Burglary Protection

•

Several modes of burglary protection: Stay, Night-Stay, Away, Instant, Maximum.

STAY: arms perimeter zones only and entry delay is on

INSTANT: same as STAY, except entry delay is off

NIGHT-STAY: arms perimeter zones and selected interior zones; entry delay on

AWAY: arms perimeter and all interior zones, entry delay is on

MAXIMUM: same as AWAY, except entry delay is off

•

You can BYPASS selected zones while leaving the rest of the system armed.

•

CHIME mode alerts you to the opening of protected doors and windows while the

system is disarmed.

Fire Protection

•

Fire protection is always active (if installed) and an alarm sounds if a fire

condition is detected

•

If necessary, you can manually initiate a fire alarm using the keypad (if

programmed).

•

Refer to the Fire Alarm System section for information regarding fire protection,

smoke detectors and planning emergency exit routes.

Security Codes

•

You were assigned a 4-digit security code during system installation.

•

Use your security code when arming and disarming the system, and when

performing other system functions.

•

Other users can be assigned different security codes, each with different

authority levels, which define the system functions a particular user can perform.

Technical Manuals Online! - http://www.tech-man.com

– 6 –

6\VWHP2YHUYLHZ

&RQWLQXHG

Zones and Partitions

•

The system sensing devices have been assigned to various “zones,” which are

specific areas of protection (e.g., front door, kitchen window, etc.).

•

Zone numbers are displayed at the keypad when an alarm or trouble condition

occurs on a sensor.

•

Partitions (VISTA-20P) provide two independent areas of protection, with each

partition containing a group of zones that can be armed and disarmed without

affecting other zones or users.

•

Partitioned systems (VISTA-20P) can include a common zone area, which is an

area shared by users of both partitions (such as a lobby in a building).

Arming, Step-Arming and Disarming Burglary Protection

•

The system must be armed before the burglary protection can sense intrusions.

•

To arm your system, enter your user code followed by the desired arming key.

•

If programmed, the [#] key can be pressed instead of entering the security code

when arming the system.

•

You can also use the step-arming key, if programmed, to arm the system, which

lets you use a function key to arm the system in one of three modes by simply

pressing the key repeatedly.

•

To disarm the system, enter your user code then press the [OFF] key.

Alarms

•

When an alarm occurs, both the keypad and external sounders will sound, and

the keypad will display the zone(s) causing the alarm.

•

If your system is connected to a Central Monitoring Station, an alarm message

will also be sent.

•

To stop the alarm sounding, simply disarm the system.

Memory of Alarm

•

When an alarm condition occurs, the keypad displays the number(s) of the

zone(s) that caused the problem, and displays the type of alarm.

•

The message remains displayed even after disarming the system, but can be

cleared with another “off” sequence.

Technical Manuals Online! - http://www.tech-man.com

– 7 –

6\VWHP2YHUYLHZ

&RQWLQXHG

Phone Access

•

If included, a phone module permits you to access the system via a touch-tone

phone, either on-premises or by call-in when away.

•

You can receive synthesized voice messages over the telephone regarding the

status of the security system.

•

You can arm and disarm the system and perform most function commands

remotely via the telephone, with voice confirmation provided after each command

entry.

•

Complete information regarding the use of this feature is provided in a separate

manual entitled “Phone Access User's Guide” that is supplied with the voice

module.

Paging Feature

•

If programmed, the system can automatically send certain system condition

messages to up to four (VISTA-20P) or two (VISTA-15P) pagers.

•

The display consists of code numbers that indicate the type of condition that has

occurred.

Function Keys

•

The “A”, “B”, “C”, and “D” keys on the keypad can be programmed to perform

various functions.

•

Functions include: activate a Panic alarm; arm the system; provide step arming;

switch lights on/off; send a message to a pager; display Time/Date; start a Macro

Scheduling

•

Your system can be programmed to automatically perform certain functions (e.g.,

arm the system) at a predetermined time each day.

Technical Manuals Online! - http://www.tech-man.com

– 8 –

$ERXW7KH.H\SDGV

*HQHUDO,QIRUPDWLRQ

Your keypads allow you to control all system functions. The keypads feature the

following:

•

A telephone style (digital) keypad

•

Liquid Crystal Display (LCD) which shows the nature and location of all

occurrences

•

Built-in sounder which will sound during alarms and troubles. The sounder also

"beeps" during certain system functions and when depressing any of the keys (to

acknowledge the key press).

•

Backlighting of the LCD display windows. Backlighting turns on when entering the

premises through any assigned entry/exit door, or when any key is pressed. This

feature is helpful when a keypad is located in a dimly lit area.

IMPORTANT:

If the keypad beeps rapidly upon entering the premises, it indicates

that an alarm has occurred during your absence and an intruder may still be on the

premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe

location.

There are two basic types of keypads which are functionally the same, but they have

different types of displays.

Alpha Display 2-line alpha display keypads feature a 2-line, 32-character

alphanumeric LCD which can display system messages in

friendly English. These keypads can also be programmed

with custom zone descriptors. To access the keys on the

keypad, simply open the swing-down door.

Fixed-Word Display Fixed-Word display keypads are functionally identical to

Alpha display keypads, but the LCD display uses pre-

designated words to identify the nature and location of

occurrences. To access the keys on the keypad, simply open

the swing-down door.

OFF

MAX

INSTANT

READY

AWAY

TEST

CODE

STAY

BYPASS

CHIME

ARMED

READY

OFF

MAX

INSTANT

READY

AWAY

TEST

CODE

STAY

BYPASS

CHIME

ARMED

READY

6160_kypd

6150 FIXED-WORD KEYPAD 6160 ALPHA KEYPAD

Technical Manuals Online! - http://www.tech-man.com

– 9 –

$ERXW7KH.H\SDGV&RQWLQXHG

)L[HG:RUG'LVSOD\.H\SDG

AWAY:

All burglary zones, interior and

perimeter, are armed.

STAY:

Perimeter burglary zones, such as

protected windows and doors, are

armed.

INSTANT:

Entry delay is turned off:

Lit with STAY = Instant mode

Lit with AWAY = Maximum mode

ALARM

FIRE

AWAY

BYPASS

STAY

CHECK INSTANT CANCELED

NIGHT NO AC

NOT READY

CHIME BAT

PHONE TEST

6150disp

TYPICAL FIXED-WORD DISPLAY

(6150 shown)

BYPASS:

This appears when one or more burglary protection zones have been

bypassed.

NOT READY:

Appears when burglary portion of the system is not ready for arming

(due to open protection zones). The system is ready to arm when this

message disappears and the READY indicator light comes on.

NO AC:

Appears when AC power has been cut off. System is operating on

backup battery power.

AC:

Appears when AC power is present.

CHIME:

Appears when the CHIME feature is activated.

BAT:

Low battery condition in a wireless sensor (if zone number displayed)

or low system battery (if no zone number displayed).

ALARM:

Appears when an intrusion has been detected and the system is armed

(also appears during a fire alarm or audible emergency alarm).

Accompanied by the protection zone in alarm.

CHECK:

Appears when a malfunction is discovered in the system at any time or

if an open is detected in a FIRE zone at any time or a fault in a

DAY/NIGHT burglary zone during a disarmed period. Accompanied by

a display of zone number in trouble.

FIRE

: Appears when a fire alarm is present. Accompanied by a display of the

zone in alarm.

A FIRE display also appears when a fire alarm is manually activated,

accompanied by a display of emergency key zone number programmed

for fire.

Technical Manuals Online! - http://www.tech-man.com

– 10 –

)XQFWLRQVRIWKH.H\SDGV

DISPLAY WINDOW.

Alpha Display Keypads:

2-line, 32-

character Liquid Crystal Display (LCD)

keypads that display protection point

identification, system status, and messages.

Fixed-Word Display Keypads:

Display

protection zone ID and system status

messages using pre-designated words in the

LCD display.

OFF

Disarms burglary portion of the

system, silences alarms and audible trouble

indicators, and clears visual display after

problem's correction.

AWAY

Arms the entire burglary system,

perimeter and interior.

STAY

Arms perimeter portion of burglary

system only. Interior protection is not armed,

allowing movement within premises without

causing an alarm.

TEST

Tests the system and alarm

sounder if disarmed. Refer to Testing The

System section for test procedures.

BYPASS

Removes individual protection

zones from being monitored by the system.

CODE

Used to assign additional user

codes for other users of the system.

CHIME

Turns CHIME mode on and off.

When on, the opening of windows or doors

while the system is disarmed will sound 3

beeps at the keypad(s).

This key can be used for "Quick

Arming" of the system without use of a

security code (if programmed).

10.

KEYS 0–9:

Used to enter your security

code(s) and to perform their associated

system functions after the security code has

been entered.

11.

✱

READY

Used to display all open protection

zones.

12.

INSTANT

Arms in manner similar to the

STAY mode, but without the entry delay

feature. Entering via an entry/exit door will

cause an alarm.

13.

MAXIMUM

Arms the entire burglary system,

perimeter and interior, but without entry

delay feature. Entering via an entry/exit door

will cause an alarm.

14.

FUNCTION KEYS:

Keys A, B, C, D may

have been programmed for a variety of

functions, including panic (emergency)

functions. For details, see the Function Keys

section.

15.

READY INDICATOR:

(GREEN) Lit when

the system is

ready to be armed (no faults

present). While the system is disarmed, this

indicator will go on and off as protection

zones are closed and opened.

16.

ARMED INDICATOR:

(RED) Lit when the

system has been armed.

17.

INTERNAL SOUNDER:

The built-in

sounder mimics the alarm sounder during

alarms, and will also "beep" during certain

system functions.

Technical Manuals Online! - http://www.tech-man.com

– 11 –

)XQFWLRQVRIWKH.H\SDGV&RQWLQXHG

OFF

MAX

INSTANT

READY

AWAY

TEST

CODE

STAY

BYPASS

ARMED

READY

V20P-001-V0

CHIME

(Keypads shown without swing-down front door)

IMPORTANT!

•

When entering codes and commands, sequential key depressions must be made

within 4-5 seconds of one another. If 4-5 seconds elapse without a key depression, the

entry will be aborted and must be repeated from its beginning. Be sure to observe

this precaution when performing any of the procedures in this manual.

• If you make a mistake while entering a security code, stop, press the [

✱

] key, and

then start over. If you stop in the middle while entering a code, and then

immediately start the entry over, an erroneous code might be entered.

Technical Manuals Online! - http://www.tech-man.com

– 12 –

(QWU\([LW' HOD\V

Your system has preset time delays, known as exit delay and entry delay.

([LW'HOD\

Exit delay gives you time to leave through the designated exit door without setting

off an alarm. Exit delay begins immediately after arming your system in any

arming mode and Alpha Display keypads display the message “You May Exit Now.”

When “You may exit now” disappears, the system is fully armed.

If programmed, a slow

beeping will sound during the exit delay period until the last 5 seconds, which then

changes to fast beeping (alerting you to the end of exit delay). If you cannot leave by

this time, you should stop, disarm the system, and start over to avoid a false alarm.

Exit Delay Restart.

If you wish to open the entry/exit door to let someone in after arming

STAY, you can re-start the

exit

delay at any time –

simply press the

[

✱

]

key

, then let that

person in. The system automatically re-arms when exit delay expires, which avoids having to

disarm the system and then re-arm it again. In addition, when the system is armed AWAY,

re-entering the premises (e.g., forgot a wallet) through the entry/exit door before exit delay

time expires will reset the exit delay time.

(QWU\'HOD\

Entry Delays give you time to disarm the system when you re-enter through the

designated entrance door. You must disarm the system before the entry delay period

ends, or an alarm will occur. The keypad beeps during the entry delay period,

reminding you to disarm the system. There are two entry delays (if programmed). The

first is for your primary entrance and the second can be used for a secondary entrance,

where a longer delay is required to walk to the keypad to disarm the system.

You can also arm the system with no entry delay at all by using the INSTANT or

MAXIMUM arming mode. This mode provides greater security while on the

premises or while away for extended periods of time.

See your installer for your delay times.

Partition 1___________________________________________________________

Exit Delay:

seconds Entry Delay 1: seconds

Entry Delay 2:

seconds

NOTE:

Entry/Exit times set for partition 1 also apply to the common zone (VISTA-20P).

Partition 2 (VISTA-20P)______________________________________________

Exit Delay:

seconds Entry Delay 1: seconds

Entry Delay 2:

seconds

Technical Manuals Online! - http://www.tech-man.com

– 13 –

(QWU\([LW'HOD\V

&RQWLQXHG

([LW$ODUPV

Whenever you arm the system, the exit delay begins. If an entry/exit door or interior

zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds

an alarm and starts the entry delay timer. If you disarm the system before the entry

delay ends, the alarm sound stops and the message "CANCELED ALARM" or "CA" is

displayed on the keypad, along with a zone number indicating the faulted zone. No

message is sent to the Central Monitoring Station.

To clear the exit alarm condition, the open zone must be made intact; to clear the

display, enter your code plus OFF.

If you do not disarm the system before the entry delay ends, and an entry/exit door or

interior zone is still open, the alarm sound continues and an "exit alarm" message is

sent to the Central Monitoring Station. The message ""EXIT ALARM" or "EA" is

displayed on the keypad, along with a zone number indicating the faulted zone. To

stop the alarm, the system must be disarmed (your code plus OFF); to clear the

display, enter your code plus OFF a second time.

An “exit alarm” also results if an entry/exit door or interior zone is faulted within two

minutes after the end of the exit delay.

Your system may have been programmed for this feature to minimize false alarms sent to the Central

Monitoring Station. Ask your installer if "Exit Alarm" is active in your system. If so, check this box.

&KHFNLQJ)RU2SHQ=RQHV

8VLQJWKH>∗@.H\

efore arming your system, all protected doors, windows and other protection zones

must be closed or bypassed, otherwise the keypad will display a "Not Ready"

message.

Use the READY

key to display all faulted zones, making it easier for you to identify

and secure any open zone.

1. Press [

∗

] (do not enter code first) to display faulted

zones

2. Secure or bypass the zones displayed.

The keypad’s READY indicator lights when all

protection zones have been either closed or bypassed.

4. Arm the system as desired.

Alpha Display:

∗

Fixed-Word Display:

Zone no. and “NOT READY”

Technical Manuals Online! - http://www.tech-man.com

– 14 –

$UPLQJWKH6\VWHP

6WD\0RGH$UPV3HULPH WHU2QO\(QWU\'HOD\2Q

•

Used when you want to arm the system with persons staying inside (or if you have

pets that are moving throughout the premises).

•

The perimeter sensors are armed, but interior sensors are left disarmed.

•

Exit delay begins (you can leave through the entry/exit door, if desired).

•

An alarm sounds if any protected window or non-entry/exit door is opened.

•

You may otherwise move freely within the premises.

•

Persons entering later can enter through an entry/exit door, but they must disarm

the system within the entry delay period to avoid sounding an alarm.

1LJKW6WD\0RGH$UPV3HULPH WHU2Q O\3OX V6HOHFWHG=RQHV

•

Use Night-Stay mode to provide increased security while staying inside.

•

Arms same as Stay mode, but also arms pre-selected interior sensors (programmed

by your installer), while other interior sensors are left disarmed.

•

Persons entering later can use an entry/exit door but must not violate any of the

programmed interior zones to avoid sounding an alarm.

•

IMPORTANT: When Night-Stay mode is on, the selected interior zones are armed and cause an

alarm if anyone enters those areas (e.g., waking in the middle of the night). To avoid sounding an

alarm, you must disarm the system before any activity takes place in those interior zones.

,QVWDQW0RGH$UPV3HULPHWHU2QO\(QWU\'HOD\2II

•

Used when staying inside and do not expect anyone to use an entry/exit door.

•

Arms same as Stay mode.

•

An alarm sounds immediately if any protected perimeter window or any door is

opened, including entry/exit doors.

•

IMPORTANT: Arming in this mode greatly increases the chance of false alarms. Use extreme

care in selecting this mode of arming.

$ZD\0RGH$UPV(QWLUH6\VWHP(QWU\'HOD\2Q

•

Used when nobody will be staying inside (including pets).

•

The entire system (interior and perimeter) is armed.

•

Exit delay begins letting you leave through the entry/exit door.

•

An alarm sounds if a protected window or any door is opened, or if any movement

is detected inside your premises.

•

You can reenter through an entry/exit door, but you must disarm the system within

the entry delay period to avoid sounding an alarm.

0D[LPXP0RGH$UPV(QWLUH6\VWHP( QWU\ 'HOD\2II

•

Used when leaving the premises for extended periods (e.g., vacation).

•

Arms same as Away mode, but entry delay is off.

•

An alarm sounds same as Away mode, and sounds upon opening entry/exit doors.

Technical Manuals Online! - http://www.tech-man.com

– 15 –

$UPLQJWKH6\VWHP

$UPLQJ& RP PD QGV

Before arming, close all perimeter doors and windows and make sure the Ready to Arm

message is displayed.

Mode Press these keys… Keypad Confirms By…

Stay security code + [3] (STAY)

• three beeps

• armed STAY message displayed

• red ARMED indicator lights

Night-Stay security code + [3] + [3]

• three beeps

• NIGHT-STAY message displayed

• red ARMED indicator lights

Instant security code + [7] (INSTANT)

• three beeps

• armed STAY message displayed

• red ARMED indicator lights

Note that entry delay is turned off.

Away security code + [2] (AWAY)

• two beeps, or, if programmed, beeping

for duration of exit delay

• armed AWAY message displayed

• red ARMED indicator lights

Leave the premises through an entry/exit

door during the exit delay period to avoid

causing an alarm. The keypad beeps

rapidly during the last 5 seconds of the

exit delay to warn you that it is ending.

Maximum security code + [4] (MAXIMUM)

• same as Away (described above)

Note that entry delay is turned off.

Quick Arming

If "Quick Arming" was programmed by the installer, the

[#]

key can be pressed in

place of the security code when arming the system. However,

the security code

must always be used to disarm the system.

Function Key Arming

For any arming command, a function key may have also been programmed for your

system. If so, you can press and hold the appropriate function key for 2 seconds to arm

the system. See your installer for the designated functions (see

Single Button

Arming

section).

Refer to the

Accessing Other Partitions

section for information on multi-partiion

arming (VISTA-20P).

Technical Manuals Online! - http://www.tech-man.com

– 16 –

$UPLQJWKH6\VWHP

6LQJOH%XWWRQ$UPLQJ

The “A”, “B”, “C”, and/or “D” keys on your keypad may have been programmed for

single-button arming. Note that while it will not be necessary to use a security code

for arming, a security code must always be used to disarm the system.

If Single-Button Arming is programmed:

•

A function key has been assigned to a specific type of arming: STAY mode,

Night-STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming

paragraph).

•

You DO NOT need to enter your user code before pressing the function key

(you always need your user code to DISARM the system).

Before arming, close all perimeter doors and windows.

Press and hold the assigned function key for 2

seconds (no code is required). Function keys are

shown below.

321

654

987

READY

INSTANT

OFF

CODE

AWAY

TEST

CHECK

STAY

BYPASS

ADT3000-007-V0

Alpha Display:

Fixed-Word Display:

Green LED lit

The keypad begins beeping and displays the armed

message. The red ARMED indicator also lights.

Alpha Display:

Fixed-Word Display:

AWAY

6WHS$UPL QJ )H DWXUH

Single-Button “Step” arming may have been programmed into one of the lettered keys

(A, B, C, or D). Check with your installer to see if this has been done in your system.

If Step-Arming is programmed:

•

The assigned key provides a choice of three levels of security.

•

The selected key can be pressed once, twice, or three times, increasing the level

of security with each press, as follows

Key

First Press

Second Press

Third Press

A, B, C, D

Armed-STAY Armed Night-STAY

(if programmed)

Armed-AWAY

Technical Manuals Online! - http://www.tech-man.com

– 17 –

8VLQJWKH.H\VZLWFK

Your system may be equipped with a keyswitch for use when arming and disarming.

Red and green lights on the keyswitch plate indicate the status of your system as

follows:

Green Light: Lights when the system is disarmed and ready to be armed (no

open zones). If the system is disarmed and the green light is off, it

indicates the system is not ready (one or more zones are open).

Red Light: Lights or flashes when system is armed in AWAY or STAY mode.

See your installer for the meanings of the lit red light:

Lit Steady = system armed AWAY or

system armed STAY and exit delay has expired

Flashing = system armed STAY and exit delay timer active

Rapid flashing = an alarm has occurred (memory of alarm).

Before arming, close all perimeter doors and windows.

To arm in the AWAY mode:

Turn the key to the right for 1/2 second and release.

Keypads beep twice and the red indicator lights or

flashes.

To arm in the STAY mode:

Turn the key to the right and hold for longer than 1

second, then release. Keypads beep three times and

the red indicator lights or flashes.

To disarm the system:

Turn the key to the right and release. The red light

turns off

GREEN

RED

Technical Manuals Online! - http://www.tech-man.com

– 18 –

'LVDUPLQJDQG6LOHQFLQJ$ODUPV

8VLQJW KH >2 )) @NH\

The OFF key is used to disarm the system, silence alarm and trouble sounds, and

clear alarm memories.

IMPORTANT

If you return and the main burglary sounder is on,

DO NOT ENTER, but

CONTACT THE POLICE from a nearby safe location.

If you return after an alarm has occurred and the main sounder has shut itself off,

the keypad will

beep rapidly upon your entering,

indicating that an alarm has occurred during your

absence.

LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.

+ 1

(Security Code)

OFF

The “READY” indicator light will be lit if all zones

are secure, and the keypad will emit a single tone to

confirm that the system is disarmed.

Alpha Display:

Fixed-Word Display: READY

To Silence a Burglary Alarm and Clear a Memory of Alarm

Enter your security code and press the OFF key to silence the alarm (or warning

tones of a Memory of Alarm).

Note the zone in alarm on the keypad display, and make that zone intact (close

door, window, etc.). Now enter the security code plus OFF sequence again to clear

the keypad’s Memory of Alarm display.

To Silence a Fire Alarm and Clear Memory of Alarm

Simply press the OFF key to silence the alarm. Then enter the security code plus

OFF sequence to clear the keypad's Memory of Alarm display. See the Fire Alarm

System section.

Technical Manuals Online! - http://www.tech-man.com

– 19 –

%\SDVVLQJ3URWHFWLRQ=RQHV

8VLQJWKH%<3$66.H\

Use t

his key when you want to arm your system with one or more zones intentionally

unprotected. The system must be disarmed first.

Vent Zones:

Your system may have certain windows set as “vent” zones, which are

automatically bypassed if left open when arming the system (you do not need to

manually bypass them). However, if a vent zone window is closed

after

arming, it

becomes protected and will cause an alarm if opened again while the system is armed.

When bypassing zones:

•

The system must be disarmed before you can bypass zones.

•

Bypassed zones are unprotected and will not cause an alarm if violated.

•

The system will not allow fire zones to be bypassed.

•

Zones are automatically unbypassed when the system is disarmed.

+ 6 + zone numbers (see below)

(Security Code)

BYPASS

Enter the 2-digit zone number(s) for the zone(s) to be

bypassed (e.g., 06, 10, 13, etc.). Single digit zone

numbers must be preceded by a zero (e.g. 05, 06).

Alpha Display:

Fixed-Word Display:

NOT READY

When finished, the keypad will momentarily display

a "Bypass" message for each bypassed zone number.

Wait for all bypassed zones to be displayed.

Arm the system as usual. When armed, the arming

message is displayed with “ZONE BYPASSED.”

To display bypassed zones prior to arming, enter

your security code and press the [6] BYPASS key.

Alpha Display:

Fixed-Word Display:

BYPASS

Alpha Display:

Typical armed display after

bypassing zones.

Technical Manuals Online! - http://www.tech-man.com

– 20 –

%\SDVVLQJ3URWHFWLRQ=RQHV

4XLFN%\S DVV

If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones

without having to enter zone numbers individually. This feature is useful if, for

example, you routinely leave certain windows open when arming at night.

+ 6 + [#]

(Security Code)

BYPASS

In a few moments, all open zones will be displayed

and automatically bypassed.

Make sure that only those

zones that you wish to leave unprotected are bypassed, and

that there are no other zones unintentionally left open.

Alpha Display:

Fixed-Word Display:

NOT READY

Wait for all bypassed zones to be displayed, then arm

the system as desired.

Alpha Display:

Fixed-Word Display: BYPASS

Ask your installer if "Quick Bypass" is active for your system, and if so, check here:

&KLPH0RGH

CHIME mode alerts you to the opening of a perimeter door or window while the

system is disarmed.

When Chime mode is activated:

•

Three tones sound at the keypad whenever a perimeter door or window is opened.

•

Interior zones do not produce a tone when they are faulted.

•

Pressing the READY key will display the open protection points.

•

Chime mode can be used only while the system is disarmed.

To turn Chime Mode on:

+ 9

(Security Code)

CHIME

The CHIME message will appear. Perimeter zones

will cause a tone when faulted.

Alpha Display:

Fixed-Word Display:

READY

To turn Chime Mode off:

+ 9 again

(Security Code)

CHIME

The CHIME message will disappear.

Alpha Display:

Fixed-Word Display:

CHIME

Technical Manuals Online! - http://www.tech-man.com

La pagina sta caricando ...

ADEMCO VISTA-20P Series Manuale utente

Marca: ADEMCO

Modello: VISTA-20P Series

Categoria: Sistemi di controllo accessi di sicurezza

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: ADEMCO VISTA-20P Series User manual

ADEMCO VISTA-20P Series Manuale utente

Questo manuale è adatto anche per

ADEMCO VISTA-20P Series Manuale utente

in altre lingue

Documenti correlati

Altri documenti