Aritech CS350 Installation Instructions Manual

Marca: Aritech

Modello: CS350

Categoria: Antincendio

Tipo: Installation Instructions Manual

14 1791 999 1

This manual contains installation details for

the CS350 control panels.

It provides the basic programming and instal-

lation information required by technicians and

engineers.

CS350

Installation Instructions

Downloaded from: http://www.guardianalarms.net

14 1791 9992

14 1791 999 3

CONTENTS

FEATURES .................................................................................................................................... 3

KEYPAD INSTALLATION ........................................................................................................... 4-5

WIRING SPECIFICATIONS ...........................................................................................................5

POWERING UP PANEL ................................................................................................................. 6

HOW TO PROGRAMME ................................................................................................................7

PROGRAMMING MAP ................................................................................................................... 8

PROGRAMMING FUNCTIONS ................................................................................................... 11

PERIDIAX FEATURE ................................................................................................................... 19

PROGRAMMING TEXT ............................................................................................................... 20

RETURNING TO FACTORY DEFAULT ...................................................................................... 21

QUICK CODES ............................................................................................................................ 21

ZONE WIRING OPTIONS ............................................................................................................ 22

WIRING OF SIRENS .................................................................................................................... 23

WIRING OF OUTPUTS

RELAYS ........................................................................................................................... 24

DIGITAL COMMUNICATORS ......................................................................................... 24

FIRE DETECTORS ......................................................................................................... 24

LIST WITH SHORT CODES ........................................................................................................ 25

DEFAULT CHART ........................................................................................................................ 26

PROBLEM SOLVING ................................................................................................................... 27

TECHNICAL SPECIFICATION .................................................................................................... 29

MAIN PANEL WIRING DIAGRAM ............................................................................................... 30

FEATURES

The CS350 is a microcomputer based alarm control panel operating from remote keypads, and has

the following features:

l Facility for up to 4 CD3008 remote keypads... one CD3008 is supplied with the panel.

l 6 freely programmable dual zones.

l Auxiliary tamper input.

l Supervised bell tamper input.

l Digital communicator fault input... reprogrammable to include remote engineer reset.

l New perimeter system capability which provides local alarms for perimeter zone activations.

This can reduce false alarms considerably. Exremely useful with inertia shock sensors.

l 4 freely programmable open collector outputs.

l 2 freely programmable high current outputs (eg. to control sirens).

l LCD with freely programmable zone names... up to 12 characters.

l Battery input monitored.

l Four user codes.

See Programming Functions on page 14 for zone (Input) and page 15 for output types.

Features

14 1791 9994

Keypad Installation

✓

1234

ON SD

MIN MAX

CABLE ENTRY

FROM TOP

CABLE ENTRY

FROM BACK

CABLE ENTRY

FROM BOTTOM

MOUNTING HOLE

DIPSWITCHES

FOR KEYPAD ID

SPARE SCREW

TO FIX COVER

ONTO BASE

ADJUSTMENT

DISPLAY-CONTRAST

CD3008

PUSH CLAMP

GENTLY TO

REMOVE PCB

CD3008

LIFT

REMOVE SCREW

IF FITTED

PUSH

PUSH IN CLIP WITH

SCREW DRIVER AND

LIFT UP LID

Figure 1.

Figure 2.

14 1791 999 5

Keypad Installation

Wiring Specifications

Connect the additional keypads either using a STAR or MULTIDROP configuration.

MULTIDROP the keypads are 'daisy chained' together, each keypad being connected in parallel

to the one before it.

STAR each keypad is wired back separately to the control panel terminals.

Any combination of the above wiring methods is allowed with the restriction that the total cable length

on each of the wiring loops (either multidrop or star) is restricted to 100m.

The following diagram shows how 4 RKPs may be connected using both methods.

✓

1234

ON SD

MIN MAX

SW1

CD3008

Control panel

Terminal 5

1234

OFF

1234

Keypad 1

(all off)

Keypad 2

12341234

Keypad 3 Keypad 4

Figure 3.

Figure 4.

Figure 5.

14 1791 9996

Connection of the control panel and the remote keypad in the following sequence allows the engineer

to establish that the control panel is working correctly.

Connection sequence:

1. Before installing the remote keypad (RKP) at it's designated position, it may be connected at

the control panel, to enable the engineer to commission the system.

2. Check that the ID for the RKP is set correctly... one keypad has to have ID1 (refer to Diagram

2).

3. Connect the RKP to the panel as shown in Diagram 3.

4. Replace the cover of the RKP and ensure that the tamper switch in the panel is closed.

5. Apply mains power to the panel. The system will power up in armed state (Factory Programme

Setting). If any zones are open at power up, the audibles will activate. The panel

defaults to the language select prompt when switched on for the first time [ UK/IRL Press é

1]. Enter [é] and [1] to select English language. Note that this also happens after returning to

factory default. See page 21 for more details.

6. Enter the Default User Security Code [1][1][2][2] at the keypad to disarm the system. The keypad

display shows DISARMING and the audibles, if sounding, will stop. Display then shows

any zones which are open and caused it to alarm. If [0] key is pressed at this stage, the display

will show FINISHED? . Enter ACCEPT [ü] to finish with operator menu.

7. The display shows Time/Date and the system is now disarmed.

8. Enter [1][2][7][8] (Default Engineer Code) to enter Engineer Mode and to change programme

parameters. See the Programming Map and Programming Functions for operational details.

How to programme is detailed on page 7.

9. Each time the system is powered down the panel memorizes it's current state, i.e. whether

armed, disarmed, partguard, etc. and will restore to that state when powered-up again.

Powering Up Panel

14 1791 999 7

All programmed features can be changed. The structure and position of the programming options

are illustrated in the Programming Map on the next page. Features and options are grouped together

and allocated to 6 main menu blocks:

1 MAINTENANCE 4 ZONES

2 TIMERS 5 OUTPUTS/REMOTES

3 USERS 6 MISCELLANEOUS

Once in Engineer Mode, the blocks can be accessed by 'stepping' through the menu blocks and

accepting the option shown in the display. The keys used for programme selections are defined as

follows:

[ê] stepping forward to next block or programming option

[é] returning to previous block or programming option

[ü] enter programming block - enter programming option - confirm changes - accept option

[X] quit programming block - quit programming option - reject changes

After have installed the additional keypads - mind the correct dipswitch ID setting - go to the Engineer

Programming Mode and proceed as follows:

1. Use the [ê] key till OUTPUTS/REMOTES is displayed then enter [ü] .

2. Use the [ê] key till INSTALL REMOTE is displayed then enter [ü] .

3. The display shows the keypads connected, eg. REMOTE k k ✱ ✱ . Confirm [ü] these changes

when they are correct. If not correct, verify the wiring to the keypad and dipswitch ID settings.

The keypad must be powerless when changing dipswitch settings.

4. The display now shows INSTALL REMOTE . Quit programming blocks [X] till GOODBYE is

displayed. Now accept [ü] to leave the Engineer Programming Mode.

HOW TO PROGRAMME

Adding Additional Keypads

PROGRAMMING EXAMPLE

14 1791 9998

CS350 PROGRAMMIMG MAP V1.0

1 1 Engineer Log Display Log

Clear Log

Maintenance Menu

2 Output Test nn Low

nn High

MAINTENANCE 3 Show Open Zones All Closed

nn Zone

4 Walk Test Walk Test nn

5 LED Test Testing LEDs

Main Menu

2 1 Entry Time nn

2 Exit Time nn

3 Split Time OFF/ON

4 Bell Times Bell Cutout nn

Bel Delay nn

All Bells Cut ON/OFF

TIMERS Dig Cutout ON/OFF

Perim.Bell Cutout nn

Timers Menu

5 Time hh:mm Time hh:mm

6 Date dd/mm/yy Date dd/mm/yy

7 Summertime Forward Date

Backward Date

Summertime ON/OFF

Main Menu Timers Menu

3 1 Change Codes xx Code In Use

xx Code Unused

New Code

Verify

Error

2 Code Privilege 01 Fs Us . . . . . . OK USER ATTRIBUTES

02 . . . . . . . . . . . OK

03 . . . . . . . . . . . OK Mn=Manager

04 . . . . . . . . . . . OK In=Inhibit

USERS Leave this Ps=Part Set

Us=Unset

3 Engineer Code New Code Fs=Full Set

Verify

Error

4 Duress Code New Code

Verify

Error

5 Code Count nn

êê

Open Zones ON/OFF

Main Menu

14 1791 999 9

4 1 Zone Type 01 Alarm ZONE TYPES

0x . . . . . . . . . . . .

06 . . . . . . . . . . . . Unused

Leave this Tamper

2 Zone Attributes 01 In Key

0x . . . . . . . . . . . . Fire

06 . . . . . . . . . . . . Exit/Entry

Leave this Alarm

Keypad Lock

Key Inf=Infinite Entry

Exit Trm=Exit Terminator

ZONES 3 Shock Zones nn Gross. x Pls y ZONE ATTRIBUTES

nn Wrong Type

Ls=Local Alarm Shock

4 Zone Name La=Local Alarm Contact

In=Inhibit

5 Loop Type : Alarm 24=24 hours

Loop Type : Dual Pg=Partguard

So=Soak Test

Ac=Access

Ch=Chime

KEY ZONE ATTRIBUTES

Fs=Full Set

Ps=Part Set

Us=Unset

Pu=Pulsed

Main Menu Qs=Quick Set

5 1 Output Type 01 Disarm/Arm OUTPUT TYPES

0x . . . . . . . . . . . .

06 . . . . . . . . . . . . Disarm/Arm

Alarm

P.A.

Fire

Tamper

OUTPUTS / 2 Install Remote Remote kk** Latch

REMOTES Fire Detect Reset

k=CD3008 Buzzer

Int.Bell

Ext.Bell

Partguard

System Clear

Trouble

Main Menu Perim.Alarm

Unused

Clear

CS350 Programming Map

14 1791 99910

CS350 Programming Map

6 1 Arm/Disarm Menu User Walk ON/OFF No Forced Arming

Forced Arm Opts Keep Inhibits

Rearm Options Clear when closed

ArmedDisplay ON/OFF Clear after exit

Exit Fault Buzzer/Bell

Final Door ON/OFF

Miscellaneous Menu Always rearm

Never rearm

Rearm 1 to 8 Times

2 P.A. Menu P.A. Silent/Bells

PA, LF Silent/Bells

éê PA ON/OFF

Miscellaneous Menu

3 Partgd/Chime Timed Partgd ON/OFF

Access>EE/Access

Partgd Digi ON/OFF

Latched Chime ON/OFF

Int.Bell Chime ON/OFF

Miscellaneous Menu

4 Eng. Reset Menu Reset Code/FTC or Code Only

P.A. Reset ON/OFF

Tamper Reset ON/OFF

MISCELLANEOUS Alarm Reset ON/OFF

Clear Engineer Reset

Miscellaneous Menu

5 Warnings PF Buzzer ON/OFF

LF Buzzer ON/OFF

Miscellaneous Menu

6 Factory Prog Menu Engineer Lock ON/OFF

Miscellaneous Menu

7 Change Language English

Nederlands

Francais

Italiano

8 SysClear Inputs System Clear Mains ON/OFF

System Clear Battery ON/OFF

System Clear Fuse ON/OFF

System Clear Accs+EE ON/OFF

Main Menu Miscellaneous Menu

GOODBYE

14 1791 999 11

CS350 Programming Functions

1. MAINTENANCE MENU

1.1 Engineer Log

1.1.1 Display Log

Use this function to consult the 40 event log

1.1.2 Clear Log

Will clear all events in the Engineer Log

1.2 Output Test

Use the [é ] and [ê ] keys to select the desired output. Use the [ü]

key to toggle the output polarity. Will return to its programmed status

when you move to the next output.

1.3 Show Open Zones

Will show any zone which is open. This is a useful test function.

1.4 Walk Test

Used to test individual inputs. Triggering the input will activate the

interior bell for 4 seconds,as well as latch and walk test outputs.

1.5 Led Test

This option will perform a sequential test of all keypad LED's

2. TIMERS

2.1 Entry Time

Programmable between 0 to 99 seconds.

2.2 Exit Time

Programmable between 0 to 99 seconds.

2.3 Split Entry Time

When this option is set and the entry time is exceeded, then only the

interior bells will sound. Only after the additional entry time expired,

which is half the time programmed in 2.1, will a full alarm be created.

2.4 Bell Times

2.4.1 Bell Cutout

Programmable between 0-99 minutes for exterior bell. When a

time limit is required for interior bell then see 2.4.3.

2.4.2 Bell Delay

Programmed delay in minutes for interior and exterior bells which

becomes operational only when the system is set and no digi

fault condition prevails (negative to terminal 20).

2.4.3 All Bells Cut

Select for ON if interior bell must be timed for duration of 'Bell Cutout'

time

Engineer Log

Output Test

Show open zones

Walk Test

Led Test

Entry Time

Exit Time

Split Entry Time

Bell Times

14 1791 99912

Bell Times

Time

Date

Change Codes

Code Privileges

Engineer Code

2.4.4 Digi Cutout

Select for ON if the output type 'Alarm' must reset with the Bell

cutout time. If set to OFF then this output resets when the system

is disarmed.

2.4.5 Perimeter Bell Cutout

Programmed alarm time in minutes for the 'Perim.Alarm' output

type. The exterior bell and Perimeter bell output types will reset

after this time alarm expired. See also Peridiax feature on page

19.

2.5 Time

Programme time in Hours and Minutes: hh:mm

2.6 Date

Programme date: dd / mm / yy

2.7 Summertime

2.7.1 Forward date

Date at which clock is advanced with 1 hour (start of summer-

time).

2.7.2 Backward date

Date at which clock is returned with 1 hour (start of wintertime).

2.7.3 Summertime ON/OFF

Select for ON if automatic correction to summertime is required.

3. Users

3.1 Change Codes

Programme here user code 01 to 04. Use from 4 up to 6 digits with

the exception of '0'. Deleting a code is achieved by entering [ü]

after appearance of [New code _ ]. Code 4 can be used with a

code counter (see 3.5). Factory default code for user code01is

[1122].

3.2 Code Privileges

Allocate operational functions to each code.

Attribute Function

. Mn change codes, time, date, read engineeer memory,

access to chime function

. In inhibit zones

. Ps part set of system

. Us unset of system

. Fs full set of system

3.3 Engineer Code

Programme here new Engineer code. Factory default is [1278].

CS350 Programming Functions

14 1791 999 13

3.4 Duress Code

Programme here the code which will disarm the panel and activate

the Personal Attack output. The output restores after entering a

user code.

3.5 Code Count

Programme the amount of times code 4 can be introduced. When set

to '99' code 4 is always operational. Setting to '0' disables the code.

3.6 êêOpen Zones On/Off

When this option is programmed to 'On' then a keyswitch user will

be able to view any open zones by pushing twice the [ê ] button.

3.7 Quick codes On/Off

When this option is programmed to 'On' it is possible to fast arm the

panel.

The following three keystroke sequences are possible :

[0] [ê] [4] Arms system with exit time.

[0] [ê] [5] Arms system immediately (no exit time).

[0] [ê] [7] Arms system partially (Part Set).

4. ZONES

4.1 Zone Type

Define here the typical function of each input.

TYPE FUNCTION

. Unused Input is not operational

. Tamper Input is 24Hrs operational. Activation of input causes

'internal bell' alarm in disarmed state and full alarm in

armed state. The input is automatically bypassed after

an alarm till the second valid entry of a user code.

output : tamper, alarm, int.bell, ext.bell, system clear, fire

reset

. P.A. Input is 24Hrs operational. Silent or audible Personal

Attack alarm is determined in function 6.2.1.

output : P.A., system clear, fire reset

. Key Input is 24Hrs operational to arm/disarm system. The

exact operation will be determined by the attributes allo-

cated in function 4.2. Use Pulse keyswitches if more

than one input is to be used as Key zone.

output : disarm/arm, buzzer, latch

. Fire Input is 24Hrs operational. Activation of zone will cause

the sirens to pulse on and of. The input is automatically

bypassed after an alarm till the second entry of a valid

user code.

output : fire, interior bell, exterior bell, system clear, fire

reset

Duress Code

Code Count

Open Zones

Quick Codes Off

Zone Type

CS350 Programming Functions

14 1791 99914

Zone Type

Zone Attributes

Key Zones

CS350 Programming Functions

TYPE FUNCTION

. Exit/Entry Input is bypassed during exit time when arming the

system. If after the exit time the zone is still open, the

panel will not arm and act as programmed in

function 6.1.5. During the entry procedure the entry

timeris started which allows disarming.

output : buzzer, alarm, interior bell, exterior bell, fire

reset

. Alarm Input is only active when the system is armed and

it will act according to its programmed attributes.

outputs : alarm, interior bell, exterior bell, system

clear, fire reset

. Keypad Lockopening this input will disable access to the keypad.

. Key Infinite creates an infinite exit time. Only after opening and

closing this zone will the panel arm after four

seconds. Re-activation starts an infinite entry time.

. Exit The exit time stops and system arms 4 seconds

after Terminator closing the input.

4.2 Zone Attributes

Attributes define the operation of the zone type. Some types

have attributes inherent to them. Others can not be changed

which will be displayed by [No Option].

ATTRIBUTE FUNCTION

. In Allows inhibiting of alarm and exit/entry zones

. 24 Creates a 24Hrs zone. Only applicable for Alarm types.

. Pg Partguard. Zone is inhibited during partguard protection.

. So Soak Test. The related input will not activate any alarm output

but only log its events.

. Ac Access zone. Follows the exit/entry input. Will create a direct

alarm when triggered prior to the exit/entry input, except if pro-

grammed for Access/EE and the panel is in Partguard mode (see function

6.3.2.).

. Ch Chime. Input activates buzzer/ interior bell when in disarmed

state.

. Ls Local Shock. Shock sensor alarm triggers 'perimeter' output

instead of 'alarm' output. See also Peridiax programming on p.19.

. La Local Alarm. Both shock sensor and/or contact activation will

trigger the perimeter output. See also Peridiax programming on p.19.

14 1791 999 15

KEY ZONE ATTRIBUTES

. Fs Full set. Keyswitch fully arms system.

. Ps Part set. Keyswitch partially arms system.

. Us Unset.Keyswitch disarms system.

. Pu Pulse.Keyswitch used must be a pulse type. Allows

arming/disarming with multiple keyswitches in a sys-

tem.

. Qs Quick set. Keyswitch arms panel without exit time.

4.3 Shock Zones

Input 1 to 4 can be programmed to analyse enertia shocks (e.g. GS610).

Two types of attack can be calibrated for. Heavy attacks ( 'gross'

level) and small repetitive attacks ('pulse' count). The pulse count

ismonitored after the first triggering in a window of 30s with 1s

intervals.

4.4 Zone Names

Programme here personalised names for each input.

(See page. 20 for example.)

4.5 Loop Type

Inputs can be configured to detect alarm contact activations only

('Alarm') or alarm and tamper violations within the same loop ('Dual').

5. OUTPUTS / REMOTES

5.1 Output Type

Define here the typical function of each output (1 to 6).

TYPE FUNCTION

. Disarm/Arm Reflects the control panel's arm/disarm status.

. Alarm Switches with intrusion and tamper alarm

(Tamper only when armed).

. PA Switches with PA alarm and / or Duress alarm.

. Fire Switches with a fire alarm.

. Tamper Switches with a 24Hrs and / or a tamper alarm.

. Latch Switches after exit time and / or walk test. Resets

with disarm or start of entry time.

Used withlatching sensors.

. Fire Reset Switches with second entry of a valid user code

after an alarm or after leaving the user log.

. Buzzer Follows the buzzer operation of the keypad.

. Interior Bell Follows the interior bell status.

. Exterior Bell Follows the exterior bell alarm time.

. Partguard Switches when control panel is part set.

. System Clear Reflects the system status according to the

optionsprogrammed in function 6.8.

. Trouble Indicates a system error : E²PROM error, line fault,

RKP fault, low battery, mains failure. The RKP will

display the cause of trouble.

Zone Attributes

Shock Zones

Zone Names

Loop Type : Alarm

Output Type

CS350 Programming Functions

14 1791 99916

Output Type

Install Remotes

Arm/Disarm Menu

TYPE FUNCTION

. A Alarm Switches with a perimeter alarm for the duration as

programmed in function 2.4.5. In this case the

exterior bell follows the A Alarm.

. Unused Output is not used.

5.2 Install Remotes

Only one keypad is installed when the panel is powered-up from

factory default. Additional keypads must be initialised by the panel

before they become active. When selecting [ü] install remotes, the

display will show the keypads which it recognizes, for example two

keypads: [Remote kk**]. Now enter [ü] again to initialize the other

keypad(s).

CS350 Programming Functions

6. MISCELLANEOUS

6.1 Arm / Disarm Menu

Programming of options associated with arming / disarming.

6.1.1 User Walk On/Off

When an input is open during arming of the panel, the interior

bell will give a short activation each time a zone is closed.

6.1.2 Forced Arm Opts

Determine here the' forced arming' conditions. Input(s) and

code(s) must have the 'In' attribute to be able to force arming of

the panel. Forced arming can be achieved in three ways.

a) Go to the [Forced Arm ] menu in the user mode and accept.

b) Arm the panel and enter [éé] when the display shows [Open

Zone(s)].

c) Arm the panel with a keyswitch while a 'forced arm' option

has been programmed.

Option Operation

. No forced arming Forced arming is not possible.

. Keep inhibits Open zones are omitted till the panel is dis-

armed.

. Clear when closed Open zones are omitted till they close

again. From that moment on they can detect

again.

. Clear after exit Open zones are omitted till the exit time has

expired, after which they can detect again.

6.1.3 Rearm Options

Define the condition of retriggering of bells.

Option Operation

. Always Rearm The same input when activated, will al-

ways retrigger sirens.

. Never Rearm The same input will not re-trigger the sirens.

. Rearm 1 to 8 times Limits the number of re-triggerings as

programmed.

14 1791 999 17

6.1.4 Armed Display On / Off

Determines if the display will show the armed status or time & date

when armed.

6.1.5 Exit Fault Buzzer/Bell

Deterines if the buzzer only or buzzer + interior bell will activate

with an exit fault.

6.1.6 Final Door On / Off

After introducing the code, the panel will arm 4s. after having opened

and closed the exit zone or access zone even before the exit time

has expired.

6.2 P.A. Menu

6.2.1 P.A. Silent/Bells

Programme if a PA alarm must be silent or loud.

6.2.2 PA,LF Silent/Bells

Programme if a PA alarm must be silent or loud when a phone line

fault is present.

6.2.3 éê PA On/Off

Programme if the keypad panic buttons are operational or not.

6.3 Partguard / Chime

6.3.1 Timed Partguard On/Off

Define if the panel is armed with or without exit time.

6.3.2 Access zones with Partguard

Define if an access zone becomes an entry/ exit zone when

partially armed or not.

6.3.3 Partguard Digi On/Off

Define if the alarm output operates when partially armed or not.

6.3.4 Latched Chime On/Off

If Latched Chime is set to On, the chime will remain operational

each time the system is disarmed untill manually canceled by user.

6.3.5 Interior Bell Chime On/Off

Define if the interior bell follows the chime function or not.

6.4 Engineer reset menu

Define the conditions which will call for an engineer reset. When

a panel asks for [Call Engineer nn], were nn is a number, the user

can't arm his panel.

6.4.1 Reset Code/FTC input or Code only

When made negative,Input 20 (Fail To Communicate or Digi Fault)

may be used to clear engineer reset. When only a code is allowed

to reset, programme for [Reset Code Only].

CS350 Programming Functions

Armd/Disarm Menu

P.A. Menu

Partguard/Chime

Engineer reset

14 1791 99918

6.4.2 P.A. Reset On/Off

Define if PA alarm requires engineer reset or not.

6.4.3 Tamper Reset On/Off

Define if Tamper alarm requires engineer reset or not.

6.4.4 Alarm Reset On/Off

Define if Alarm type input (including Tamper when armed)

requires engineer reset or not.

6.4.5 Clear Engineer Reset

Clear an engineer reset request. [Reset Cleared !] will be

displayed.

6.5 Warnings

6.5.1 PF Buzzer On/Off

Define if a 230V mains failure must trigger the buzzer output.

6.5.2 LF Buzzer On/Off

Define if a Digi Fault (via input 20) must trigger the buzzer output.

6.6 Engineer Lock

Define if an engineer code is required to factory default the

panel. See also the chapter returning to factory default.

6.7 Change Language

Change the language used by the panel to Dutch, French or Italian.

6.8 System Clear Inputs

Define the parameters which will determine the function of the

System Clear output.

6.8.1 System Clear Mains On/Off

Will a 230V mains failure switch the output off or not.

6.8.2 System Clear Battery On/Off

Will a battery failure switch the output off or not.

6.8.3 System Clear Fuse On/Off

Will a fuse failure switch the output off or not.

6.8.4 System Clear Access + EE On/Off

Will an open access or EE zone switch the output off or not.

P.A. Menu

Warnings

Engnr. Lock Off

Change Language

System Clear

Inputs

CS350 Programming Functions

14 1791 999 19

The CS3503 control panel has been equipped with Aritech's new Perimeter and Dialler eXtended

programming option.

How It Works

When the panel is armed and not in alarm state, activating a perimeter zone will cause a Perimeter-

Alarm or Local Alarm. This means that both internal and external bells sound for a programmable

number of minutes (perimeter bell time).

l A Perimeter Alarm digi output will turn on and reset at the end of the perimeter bell cutout time.

l The main alarm digi will not turn on.

l Engineer reset and rearm option are not activated by Perimeter-Alarm.

l Perimeter-Alarms that occur during exit time, after silent PA etc. are treated like normal alarms.

l Perimeter-Alarms that occur during bell delay/cutout will merely set Perimeter-Alarm digi output.

l The output functionality is fixed... both bells go for the Perimeter-Time when a Perimeter-Alarm

happens.

Typical Application Example

WIRING

PROGRAMMING

OPERATION

Inertia Activation

'Perimeter' Alarm

'Full' Alarm

'Perimeter' Alarm

For programming see Programming

Map:

Zones è Zone attributes Ls for Shock (Zone 1-4)

La for Contacts(Zone 1-6)

Timers

è Bell times è perim. bell cutout ON/OFF

WEAPON AGAINST FALSE ALARMS

Consider, for example, the situation where the inertia sensor and magnetic contact are wired in series

and mounted on a window. When only the zone attributes Ls is added , then the panel will cause

a local alarm for inertia sensor activations and a full alarm when the window opens.

Shock Option

No Ls

Contact Activation

'Full' Alarm

'Perimeter' Alarm

PROGRAMMING AND OPERATION

Figure 6.

Zone Attribute

NO La

Peridiax Feature

14 1791 99920

EXAMPLE

Reprogram zone 1 01 zone to 01 Door .

l Enter engineer mode [0][1][2][7][8]

l Jump to zones - zone name [4][4] - display shows 01 zone

l Confirm to reprogram 4 - display shows 01 _

l Start programming capital letter'D' [2] - display shows 01 2

Repeat steps till 'D' appears [2]+[2]+.. - display shows 01 D

l Move to next character ê - display shows 01 D_

l Repeat programming sequence for all characters.

l Confirm new name when the last character shows on the display 4 you can now proceed with

the next name ê or return to the previous menu section X .

Literal text is available for programming customized zone and user names. The keypad digits each

represent a set of characters.

KEYPAD CHARACTER SET

HOW TO PROGRAM NAMES

Function keys used:

ê key Move to next character.

é key Move to previous character.

4 key . Confirm to reprogram current text

. Confirm changes to the description shown on the

display after programming.

key . Restart the programming of a name

. Return to previous menu section.

Programming Text

✓

ABC DEF GHI

JKL

MNO

PQR

STU

VWX YZ

CURSOR

RIGHT

HOME

CURSOR

LEFT

SCROLL

DOWN

The [9] key has a blank space and

punctuations (eg. full stop, comma,

etc.).

The [0] key has a blank space.

La pagina si sta caricando...

Aritech CS350 Installation Instructions Manual

Marca: Aritech

Modello: CS350

Categoria: Antincendio

Tipo: Installation Instructions Manual

Scarica PDF

rapporto

in altre lingue

English: Aritech CS350

Aritech CS350 Installation Instructions Manual

Aritech CS350 Installation Instructions Manual

in altre lingue

Documenti correlati

Altri documenti