Belkin F7D1401 Manuale utente

Marca: Belkin

Modello: F7D1401

Categoria: Router

Tipo: Manuale utente

Questo manuale è adatto anche per

Surf WIRELESS ROUTER WITH BUILT-IN MODEM

User Manual

8820ed00388_F7D1 401_v1

English

Français

DEutsch

nEDErlanDs

TABLE OF CONTENTS

Getting Started ........................................... 3

What’s in the Box ............................................. 3

Initial Setup .................................................. 3

Advanced Tools & Settings..................................... 8

The Belkin Router Manager .................................... 9

Manual Setup Using Your Browser ............................. 10

Adding Computers to Your Network ............................ 11

Getting to Know Your Router .............................. 13

Front Panel ................................................. 13

Back Panel ................................................. 14

Technical Features .......................................... 15

Technical Details ........................................ 16

System Requirements........................................ 16

Troubleshooting, Support, and Warranty ................... 17

Troubleshooting ............................................. 17

Belkin International, Inc., Limited 2-Year Product Warranty.........25

Regulatory Information ................................... 28

FCC Statement.............................................. 28

What’s in the Box

Surf Wireless Modem-Router

ADSL cable (attached to router)

In some regions, a phone-jack adapter (microfilter) will be included.

Power supply (attached to router)

Ethernet cable

Network information card (attached to router)

Belkin Setup CD with User Manual

Initial Setup

Where to Place Your Router

For the best results, place the Router in an open location

away from large metal objects and magnets such as those

found in speakers. Raising the Router above floor level

can improve the strength of your wireless signal.

GETTING STARTED

How to Set It Up

GETTING STARTED

1. Connect your Router’s ADSL cable to your phone jack or phone-

jack adapter (microfilter). If you are replacing an existing Router

or gateway, this may require unplugging the existing gateway.

Note: If required by your Internet Service Provider (ISP),

plug the included phone-jack adapter (microfilter) into your

wall-mounted phone jack. Please check with your provider

before connecting your Router if you are unsure whether or

not you need to use the included phone-jack adapter.

2. Plug the Router’s power supply into a wall outlet.

3. Put the CD into your computer. If the CD doesn’t

open automatically, please browse to your CD drive

and double-click on the Belkin Setup CD icon.

4. Click the Setup icon on the CD menu.

Setup

GETTING STARTED

5. After a brief installation, the setup software will ask you

for the network name and password from the network

information card that is attached to your Router. Store the

card under the base of your Router for future reference.

GETTING STARTED

6. A progress screen will appear while additional software is

installed. This may take a few minutes to complete. Once

finished, a “Success” message will appear indicating that you

are connected to the Internet via your new Belkin Router.

During setup you may be asked for additional information.

You may need to enter a username and password provided

by your ISP. This username and password is likely to be

found on materials that came from your ISP when you

signed up for service. If necessary, you may need to contact

your ISP to retrieve your username and password.

If you have a static IP address, you may need to enter

additional information also provided by your ISP.

If your computer doesn’t have a wireless adapter, or the

setup software is unable to control it, you may be asked to

connect your computer to the Router with a network cable.

If the setup software is unable to detect your VCI and VPI

settings based on your country, you may also need to enter

this information. Your ISP is likely to have provided it.

GETTING STARTED

Advanced Tools & Settings

After the initial setup is complete, you have the option to

change settings like your network name, security type, and

password. To make these changes and others, click on the

Advanced Tools icon at the CD Setup menu and select one

of the following settings that you would like to change:

Network Name & Security – Personalize your network name

(SSID), password, and strength of wireless security.

Internet Service Provider & Login Settings – Have

you moved or changed Internet Service Providers?

If you’d like to change these settings without running

through the setup process again, this is the place.

GETTING STARTED

The Belkin Router Manager

Belkin.2234

Router Settings

User Manual

Check for Updates

Options

Exit

The Belkin Router Manager appears in your system tray

(Windows) or menu bar (Mac). Its icon indicates the current

status of your Router and also allows you to access your

Router’s settings to make changes. It also provides quick

access to software that came bundled with your Router.

To access the Router settings, click on the icon

and select from the menu that appears.

The status of your Router is shown by the Belkin Router Manager

icon, which closely mimics the light on the front of the Router.

Green: You are connected to your Belkin Router

and it is connected to the Internet.

Amber: You are connected to your Belkin Router,

but it is not connected to the Internet.

GETTING STARTED

In your browser, type “http://router” (you do not need to type

in anything else such as “www”). Then press the Enter key. If

you’re still having trouble running the manual setup option, type

“192.168.2.1” in your browser (you do not need to type in anything

else such as “http://” or “www”). Then press the Enter key.

Manual Setup Using Your Browser

GETTING STARTED

Adding Computers to Your Network

Wireless devices such as computers, network printers, and gaming

systems can connect to your Router with a few simple steps.

Using the CD

1. Put the Setup CD into your computer. If the CD

doesn’t open automatically, browse to your CD

drive and open the Belkin Setup CD icon.

2. Click the Setup icon on the CD menu.

3. After a brief installation, the setup software will ask you for the

network name and password from the network information card

that came with your Router. This card is most likely now located

underneath the foot of your Router in the provided card slot.

4. A progress screen will appear while additional software is

installed. This may take a few minutes to complete. Once

finished, a “Success” message will appear indicating that you

are connected to the Internet via your new Belkin Router.

Note: The setup software runs only on

Windows and Mac OS X systems.

GETTING STARTED

Manually

If you choose not to use the included Setup CD for

adding additional computers or wireless devices, you

can manually add these items to your network.

1. Locate the wireless-network-connections option

on your computer or wireless device.

2. Select your Belkin Router from the list of available networks. You

can identify your Belkin Router by locating the network name

(SSID) from the card located underneath the foot of your Router.

3. Enter your network password (located on

your network information card).

Your wireless device will take a few moments to connect to your

network. If the connection is not made the first time, try this

process again. If you still have difficulty connecting to your network

after trying this process a few times, see the “Troubleshooting”

section in this manual for help with connecting to your network.

Note: In some cases you may be prompted to select the

security type. It is printed on the card for your convenience.

Using the WPS Button

1. Start WPS Push Button Connection (WPS PBC) on your

computer or other Wi-Fi device that you would like to connect

wirelessly to your Router. Often there will be a button for this

purpose in software that came with the device, or a physical

“WPS,” “PBC,” or “Security” button on the device itself.

2. Within two minutes, press the WPS button on your Router.

The WPS light (small light above WPS button) will blink green while

it listens for your Wi-Fi device. Once a connection is established, the

light will turn green and then go out. If a connection is not established,

the light will blink amber. You may repeat the process to try again.

You can repeat this process for each WPS-enabled

device you’d like to add to your network.

GETTING TO KNOW YOUR ROUTER

A) Router Status Light

Your Router’s status is shown by the light on the front.

Off: The Router is not plugged into a power source.

Blinking Green: The Router is starting up.

Solid Green: The Router is connected to the Internet.

Blinking Amber: Either the ADSL (RJ11) cable

is not plugged in, or there is no signal.

B) Wi-Fi Protected Setup (WPS) Light and Button

The WPS button on the front of your Router can be used to

help establish a secure connection between your Router and

other WPS-enabled Wi-Fi devices such as computers. To use

the WPS feature on your Router, see “Getting Started > Adding

Computers to Your Network > Using the WPS Button”.

The small light near the WPS button shows what is happening

while you are using WPS to establish a connection.

Off: Idle

Blinking Green: The Router is listening for a

WPS-enabled computer or other device.

Solid Green: The Router has made a secure

connection with the computer or other device.

Amber: A connection was not created.

Front Panel

(a)

(b)

GETTING TO KNOW YOUR ROUTER

A) ADSL Connector

Connect your Router to a

phone jack using a telephone

cord. In some areas, a

microfilter might be required.

B) Wired (LAN) Connectors

Connect computers and other

wired network devices to these

ports using Ethernet cables.

C) Reset Button

This button is used to restart

your Router in rare cases when it

functions incorrectly. Resetting

the Router will preserve your

settings. This button may also

be used to restore the factory

default settings. Please see

the Troubleshooting section

for more information.

D) Power Connector

Connect the included power

supply to this jack.

Back Panel

(a)

(b)

(c)

(d)

TECHNICAL DETAILS

Technical Features

Integrated ADSL2+ Modem

The integrated ADSL2+ modem allows you to connect to the

Internet via your local Internet Service Provider (ISP) without

installing and maintaining a separate DSL modem.

Integrated 802.11n Wireless Access Point

The N150 technology enhances your Router’s

wireless capabilities, allowing for data transfer speeds

of up to 150Mbps across your network.

NAT IP Address Sharing

To save you the cost of adding IP addresses per

computer in your house, your Belkin Router uses Network

Address Translation (NAT) technology, allowing you to

share a single IP address across your network.

SPI Firewall

Your Router is equipped with a firewall that will protect your

network from a wide array of common attacks and viruses.

Universal Plug-and-Play (UPnP) Compatibility

The UPnP (Universal Plug-and-Play) feature in your Router

offers seamless operation of voice and video messaging,

games, and other applications that are UPnP-compliant.

Web-Based Advanced User Interface

You can easily make changes to your Router’s advanced

settings through your web browser. These changes can

be made from any computer on your network.

Belkin Router Monitor

The Belkin Router Monitor application helps you to monitor

your Router’s status and change network settings.

Integrated 4-Port 10/100 Switch

Your Router has a built-in, 4-port network switch to

allow your wired computers to share: printers, data,

MP3 files, digital photos, and much more.

TECHNICAL DETAILS

System Requirements

Modem Router

Broadband ADSL Internet connection with

RJ11 (telephone) connection

At least one computer with an installed network interface adapter

TCP/IP networking protocol installed on each computer

RJ11 ADSL telephone cable

Internet browser

Setup Software

A computer running Windows

XP SP2 and higher,

Windows Vista

32 and 64 bit, or

Windows 7 32 and 64 bit;

or Mac OS

X, 10.5 and 10.6

Minimum 1GHz processor and 256MB RAM

600MB of free hard-drive space for installation

TROUBLESHOOTING, SUPPORT, AND WARRANTY

Troubleshooting

The Setup CD does not automatically start.

If Belkin Setup does not run when you insert the CD-ROM, your

computer may not be configured to open CDs automatically.

If Belkin Setup does not appear within 15 seconds, browse

to your CD-ROM drive and open the “Belkin Setup” icon.

Alternatively, you may visit http://router/ and perform the

setup manually. Please see “Manual Setup Using Your

Browser” earlier in this manual for more information.

Belkin Setup cannot find my Router.

If Belkin Setup is not able to communicate with your Router during

the installation process, please check the following items.

1. Make sure that the wireless hardware on your

computer is turned on, if available.

2. Try connecting your computer to one of the four “wired”

ports on the Router with an Ethernet cable.

3. Ensure that the Router is on. The front-panel light should be on.

4. Unplug the Router’s power supply for 10

seconds, then plug it back in.

5. There may be firewall software on your computer preventing

an outgoing connection. You may choose to temporarily

disable this software before attempting setup.

If Belkin Setup still cannot find the Router, you might choose

to do a manual setup. Refer to “Manually Configuring

Network Settings” in this manual for details.

TROUBLESHOOTING, SUPPORT, AND WARRANTY

Belkin Setup cannot connect my Router to the Internet.

If Belkin Setup is not able to connect the Router to

the Internet, please check the following items:

1. Use the troubleshooting suggestions within Belkin Setup.

2. If your ISP requires a user name and password, make sure that

you have typed in your user name and password correctly. Some

user names require that the ISP’s domain may be at the end of the

name. Example: “myname@myisp.com”. The “@myisp.com” part of

the user name may need to be typed as well as your user name.

3. If you continue to have no Internet connection, refer

to “Manually Configuring Network Settings” in this

manual for an alternative setup method.

Belkin Setup completed installation, but I cannot browse the

Web. The light on the front of my Router is blinking amber.

1. Make sure the Router is connected to your ADSL line with an

RJ11 (telephone) cable via the Router’s one gray ADSL port.

2. Check that the modem (ADSL) connection is

connected to your broadband (ADSL) socket on the

wall (via an ADSL filter if one is required).

3. Unplug your Router’s power supply, wait 10 seconds,

and plug it back in. This will cause the Router to try to

reestablish communication with the ADSL line.

TROUBLESHOOTING, SUPPORT, AND WARRANTY

I can’t connect to the Internet wirelessly.

If the light on the front of the Router is solid green, then your

Router is connected to the Internet. You may not be connected

to the Router’s wireless network. Please refer to “Adding

Computers to Your Network” in this manual for instructions.

I can’t connect to the Internet wirelessly and my

network name is not listed in Available Networks.

1. Verify that your Router is on and the

front-panel light shows solid green.

2. If you are far from the Router, you might try moving

closer to see if you might have been out of range.

3. Using a computer attached to the Router via a network cable,

visit http://router/ and ensure that “Broadcast SSID” is ON.

This setting is found on the “Channel and SSID” page.

TROUBLESHOOTING, SUPPORT, AND WARRANTY

My wireless network per formance is slow, inconsistent,

suffers from weak signal, or I’m having difficulty maintaining a

VPN connection.

Wireless technology is radio-based, which means connectivity

and the throughput performance between devices

decreases when the distance between devices increases.

Other factors that will cause signal degradation (metal is

generally the worst culprit) are obstructions such as walls

and metal appliances. Note also that connection speed may

decrease as you move farther away from the Router.

In order to determine if wireless issues are related to

range, we suggest temporarily moving the computer

within 10 feet from the Router if possible.

Changing the wireless channel—Depending on local

wireless traffic and interference, switching the wireless

channel of your network can improve performance and

reliability. See the section titled “Changing the Wireless

Channel” for instructions on how to choose other channels.

Limiting the wireless transmit rate—Limiting the wireless transmit

rate can help improve range and connection stability. Most wireless

cards have the ability to limit the transmission rate. To change this

property in Windows, go to the Windows Control Panel, open “Network

Connections”, and double-click on your wireless card’s connection. In

the properties dialog, select the “Configure” button on the “General”

tab, then choose the “Advanced” tab and select the rate property.

Wireless client cards are usually set to automatically adjust

the wireless transmit rate for you, but doing so can cause

periodic disconnects when the wireless signal is too weak; as

a rule, slower transmission rates are more stable. Experiment

with different connection rates until you find the best one

for your environment. Note that all available transmission

rates should be acceptable for browsing the Internet. For

more assistance, see your wireless card’s user manual.

La pagina sta caricando ...

Belkin F7D1401 Manuale utente

Marca: Belkin

Modello: F7D1401

Categoria: Router

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Belkin F7D1401 User manual

Belkin F7D1401 Manuale utente

Questo manuale è adatto anche per

Belkin F7D1401 Manuale utente

in altre lingue

Documenti correlati