Lexmark 6500E Manuale utente

Lexmark

™

6500e

4036-310

4036-311

• Table of contents

• Start diagnostics

• Safety and notices

• Trademarks

• Index

Lexmark and Lexmark with diamond design are

trademarks of Lexmark International, Inc., registered

in the United States and/or other countries.

Edition: September 2, 2011

The following paragraph does not apply to any country where such provisions are inconsistent with local law:

LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND,

EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or

implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the

information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the

programs described may be made at any time.

Comments may be addressed to Lexmark International, Inc., Department D22X/002-1, 740 West New Circle Road,

Lexington, Kentucky 40550, U.S.A or e-mail at ServiceInfoAndTraining@Lexmark.com. Lexmark may use or distribute any

of the information you supply in any way it believes appropriate without incurring any obligation to you.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these

available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or

imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that

does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in

conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the

user’s responsibility.

Lexmark, Lexmark with diamond design, and are trademarks of Lexmark International, Inc., registered in the United States

and/or other countries.

PCL® is a registered trademark of the Hewlett-Packard Company.

All other trademarks are the property of their respective owners.

UNITED STATES GOVERNMENT RIGHTS

This software and any accompanying documentation provided under this agreement are commercial computer software

and documentation developed exclusively at private expense.

12G0476 Rev 001

4036-310, -311

Table of contents iii

4036-310, -311

Go Back

Table of contents

Table of contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Navigation buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii-x

Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Understanding the ADF and scanner glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Tools required for service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Diagnostic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Power-On Self Test (POST) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Symptom tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Error codes and messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Paper jam error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Service checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Frequent paper jam, multifeed or skew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

False multifeed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

The power does not come on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Voided line in scanned image (ADF or flatbed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Voids in flatbed scanned image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Image blank or distorted (flatbed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Image blank or distorted (ADF-front side of scanned page) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Image blank or distorted (ADF-back side of scanned page) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Strange sound generated (ADF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Strange sound generated (flatbed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

900.xx System software error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

Diagnostic aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Understanding the operator panel and menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Operator panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Understanding the home screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Using the touch screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Power On Reset (POR) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Administrative menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Accessing the service menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Configuration menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

USB Scan to Local . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Print Quality Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

SIZE SENSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Panel Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

PPDS Emulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Energy Conserve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Fax Low Power Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Min Copy Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

NumPad Job Assist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Format Fax Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

iv Service Manual

4036-310, -311

Go Back

Fax Storage Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11

ADF Edge Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11

FB Edge Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Scanner Manual Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Disable Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Paper Prompts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Envelope Prompts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Action for Prompts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Jobs On Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

Disk Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Erase All Information on Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Font Sharpening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Require Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

UI Automation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Key Repeat Initial Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Key Repeat Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

Clear Custom Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

USB Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

USB PnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14

Automatically Display Error Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14

Exit Config Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14

Diagnostics mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15

Diagnostic mode menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15

SCANNER CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

Adjust Calibration Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

Reset Flatbed Calibration Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

PRINT TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

Print Tests (input sources) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17

Print Quality Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

HARDWARE TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

Panel Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

Button Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

DRAM Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

Serial Wrap Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19

USB HS Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20

DEVICE TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20

Quick Disk Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20

Disk Test/Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20

Input Tray Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-21

PRINTER SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-21

Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-21

PERM PAGE COUNTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22

Engine Setting (1-16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22

Model Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22

Configuration ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22

REPORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22

EVENT LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23

Display Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23

Print Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . .3-23

Clear Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23

SCANNER TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23

Scanner Calibration Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23

ASIC Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23

Feed Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-23

Sensor Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-24

ADF Magnification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-24

Table of contents v

4036-310, -311

Go Back

EXIT DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Calibrating the scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Resetting the calibration values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Adjusting the scanner black and white levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Calibrating the multifeed sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28

Repair information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Handling ESD-sensitive parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Service guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Removal procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Removals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Pick roller removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Separator pad removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Front operator panel cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Left side operator panel cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

Right side operator panel cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

User interface controller card (UICC) access cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Operator panel assembly removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

UICC card removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Touch screen removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Main operator panel cover with key buttons removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22

Operator panel speaker removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

Flatbed document cover cushion removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Complete flatbed document cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Controller cage fans removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

ADF top cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31

ADF latch handle removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

ADF exit tray removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

Upper ADF scanner module removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35

ADF entry idle roller removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38

Multifeed sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39

ADF paper present sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45

ADF front and rear entry guides removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47

Flatbed cover removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-48

Flatbed scanner removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-51

Flatbed home position sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-55

Controller board removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-58

CPU cooling fan removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60

Flatbed scanner cables removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61

Power supply removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65

Engine board removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-67

Complete ADF scanner assembly removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-70

Power supply cooling fan removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-74

ADF feed roller drive belts removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-75

Lower ADF scanner module removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-78

Feed roller motor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-80

Pick roller motor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-82

Media sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-84

Paper jam sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-86

Feed rollers removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-88

Cover open sensor removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-94

vi Service Manual

4036-310, -311

Go Back

Connector locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Scanner mechanism overview and locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

External view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Card reader view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Cable locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3

Paper path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

Scanner controller board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

Engine board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-12

Power supply board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Safety inspection guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Scheduled maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Device specific scheduled maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Preventive maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2

Device specific preventive maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2

Parts catalog. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

How to use this parts catalog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Assembly 1: Covers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

Assembly 2: Operator panel and flatbed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

Assembly 3: Automatic document feeder (ADF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6

Assembly 4: Electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I-1

Part number index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I-3

Safety information vii

4036-310, -311

Go Back

Safety information

• The safety of this product is based on testing and approvals of the original design and specific

components. The manufacturer is not responsible for safety in the event of use of unauthorized

replacement parts.

• The maintenance information for this product has been prepared for use by a professional service person

and is not intended to be used by others.

• There may be an increased risk of electric shock and personal injury during disassembly and servicing of

this product. Professional service personnel should understand this and take necessary precautions.

• CAUTION: When you see this symbol, there is a danger from hazardous voltage in the area of the

product where you are working. Unplug the product before you begin, or use caution if the product

must receive power in order to perform the task.

Consignes de sécurité

• La sécurité de ce produit repose sur des tests et des

agréations portant sur sa conception d'origine et sur des composants particuliers. Le fabricant n'assume

aucune responsabilité concernant la sécurité en cas d'utilisation de pièces de rechange non agréées.

• Les consignes d'entretien et de réparation de ce produit s'adressent uniquement à un personnel de

maintenance qualifié.

• Le démontage et l'entretien de ce produit pouvant présenter certains risques électriques, le personnel

d'entretien qualifié devra prendre toutes les précautions nécessaires.

• ATTENTION : Ce symbole indique la présence d'une tension dangereuse dans la partie du

produit sur laquelle vous travaillez. Débranchez le produit avant de commencer ou faites preuve

de vigilance si l'exécution de la tâche exige que le produit reste sous tension.

Norme di sicurezza

• La sicurezza del prodotto si basa sui test e sull'approvazione del progetto originale e dei componenti

specifici. Il produttore non è responsabile per la sicurezza in caso di sostituzione non autorizzata delle

parti.

• Le informazioni riguardanti la manutenzione di questo prodotto sono indirizzate soltanto al personale di

assistenza autorizzato.

• Durante lo smontaggio e la manutenzione di questo prodotto,

il rischio di subire scosse elettriche e danni alla persona è più elevato. Il personale di assistenza

autorizzato deve, quindi, adottare le precauzioni necessarie.

• ATTENZIONE: Questo simbolo indica la presenza di tensione pericolosa nell'area del prodotto.

Scollegare il prodotto prima di iniziare o usare cautela se il prodotto deve essere alimentato per

eseguire l'intervento.

viii Service Manual

4036-310, -311

Go Back

Sicherheitshinweise

• Die Sicherheit dieses Produkts basiert auf Tests und Zulassungen des ursprünglichen Modells und

bestimmter Bauteile. Bei Verwendung nicht genehmigter Ersatzteile wird vom Hersteller keine

Verantwortung oder Haftung für die Sicherheit übernommen.

• Die Wartungsinformationen für dieses Produkt sind ausschließlich für die Verwendung durch einen

Wartungsfachmann bestimmt.

• Während des Auseinandernehmens und der Wartung des Geräts besteht ein zusätzliches Risiko eines

elektrischen Schlags und körperlicher Verletzung. Das zuständige Fachpersonal sollte entsprechende

Vorsichtsmaßnahmen treffen.

• ACHTUNG: Dieses Symbol weist auf eine gefährliche elektrische Spannung hin, die in diesem

Bereich des Produkts auftreten kann. Ziehen Sie vor den Arbeiten am Gerät den Netzstecker des

Geräts, bzw. arbeiten Sie mit großer Vorsicht, wenn das Produkt für die Ausführung der Arbeiten

an den Strom angeschlossen sein muß.

Pautas de Seguridad

• La seguridad de este producto se basa en pruebas y aprobaciones del diseño original y componentes

específicos. El fabricante no es responsable de la seguridad en caso de uso de piezas de repuesto no

autorizadas.

• La información sobre el mantenimiento de este producto está dirigida exclusivamente al personal

cualificado de mantenimiento.

• Existe mayor riesgo de descarga eléctrica y de daños personales durante el desmontaje y la reparación de

la máquina. El personal cualificado debe ser consciente de este peligro y tomar las precauciones

necesarias.

• PRECAUCIÓN: este símbolo indica que el voltaje de la parte del equipo con la que está

trabajando es peligroso. Antes de empezar, desenchufe el equipo o tenga cuidado si, para

trabajar con él, debe conectarlo.

Informações de Segurança

• A segurança deste produto baseia-se em testes e aprovações do modelo original e de componentes

específicos. O fabricante não é responsável pela segunrança, no caso de uso de peças de substituição

não autorizadas.

• As informações de segurança relativas a este produto destinam-se a profissionais destes serviços e não

devem ser utilizadas por outras pessoas.

• Risco de choques eléctricos e ferimentos graves durante a desmontagem e manutenção deste produto.

Os profissionais destes serviços devem estar avisados deste facto e tomar os cuidados necessários.

• CUIDADO: Quando vir este símbolo, existe a possível presença de uma potencial tensão

perigosa na zona do produto em que está a trabalhar. Antes de começar, desligue o produto da

tomada eléctrica ou seja cuidadoso caso o produto tenha de estar ligado à corrente eléctrica para

realizar a tarefa necessária.

Safety information ix

4036-310, -311

Go Back

Informació de Seguretat

• La seguretat d'aquest producte es basa en l'avaluació i aprovació del disseny original i els components

específics.

El fabricant no es fa responsable de les qüestions de

seguretat si s'utilitzen peces de recanvi no autoritzades.

• La informació pel manteniment d’aquest producte està orientada exclusivament a professionals i no està

destinada

a ningú que no ho sigui.

• El risc de xoc elèctric i de danys personals pot augmentar durant el procés de desmuntatge i de servei

d’aquest producte. El personal professional ha d’estar-ne assabentat i prendre

les mesures convenients.

• PRECAUCIÓ: aquest símbol indica que el voltatge de la part de l'equip amb la qual esteu

treballant és perillós. Abans de començar, desendolleu l'equip o extremeu les precaucions si, per

treballar amb l'equip, l'heu de connectar.

x Service Manual

4036-310, -311

Go Back

Preface

This manual contains maintenance procedures for service personnel. It is divided into the following chapters:

1. General information contains a general description of the printer and the maintenance approach used to

repair it. Special tools and test equipment, as well as general environmental and safety instructions, are

discussed.

2. Diagnostic information contains an error indicator table, symptom tables, and service checks used to

isolate failing field replaceable units (FRUs).

3. Diagnostic aids contains tests and checks used to locate or repeat symptoms of printer problems.

4. Repair information provides instructions for making printer adjustments and removing and installing

FRUs.

5. Connector locations uses illustrations to identify the connector locations and test points on the printer.

6. Preventive maintenance contains the lubrication specifications and recommendations to prevent

problems.

7. Parts catalog contains illustrations and part numbers for individual FRUs.

Appendix A contains service tips and information.

Appendix B contains representative print samples.

Navigation buttons

This manual contains navigation buttons in the right margin of each page, making it easier and quicker to

navigate.

Button Description

Go Back

Click to return to the last page viewed.

Conventions xi

4036-310, -311

Go Back

Conventions

Note: A note provides additional information.

Warning: A warning identifies something that might damage the product hardware or software.

Caution statement::

CAUTION

This type of caution indicates there is a danger from hazardous voltage in the area of the

product where you are working. Unplug the product before you begin, or use caution if the

product must receive power in order to perform the task.

xii Service Manual

4036-310, -311

Go Back

General information 1-1

4036-310, -311

Go Back

1. General information

Overview

The Lexmark™ 6500e option is a multifunction solution that offers integrated print, copy, fax, and network-

scanning capabilities for large workgroups. The Lexmark™ 6500e option enables a user to make quick copies,

to change the settings on the touch screen to perform specific copy jobs, to send faxes to multiple fax

destinations at the same time, to scan documents to send to an e-mail address, computer, a USB flash memory

drive, or FTP destination, and to scan documents and send them to another printer (PDF by way of FTP). When

the printer is converted into a multifunction device, all printer messages will appear on the Lexmark™ 6500e

option touch screen.

1-2 Service Manual

4036-310, -311

Go Back

Features

Understanding the ADF and scanner glass

The ADF is used for multiple pages, including duplex pages.

To use the ADF:

• Load letter- and A4-size documents into the ADF facedown, long edge first.

• Load legal- and A3-size documents into the ADF facedown, short edge first.

• Load up to 100 sheets of plain paper in the ADF tray.

• Scan sizes from 50.8 x 76.2 mm (2 x 3 in.) to 299.7 x 431.8 mm (11.8 x 17 in.).

• Scan documents with different paper sizes (letter and legal).

• Scan media weights from 52 to 120 g/m2 (12 to 34 lb).

• Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as

magazine clippings) into the ADF. Place these items on the scanner glass.

General information 1-3

4036-310, -311

Go Back

The scanner glass is used for singles pages or book pages, small items (such as postcards or photos),

transparencies, photo paper, or thin media (such as magazine clippings).

To use the scanner glass:

• Place a document facedown on the scanner glass in the lower left corner.

• Scan or copy documents up to 114 mm x 140 mm (4.5 x 5.5 in.) to 216 x 356 mm (8.5 x 11 in.).

• Copy books up to 25 mm (1 in.) thick.

For information on the operator panel, see “Understanding the operator panel and menus” on page 3-1.

1-4 Service Manual

4036-310, -311

Go Back

Tools required for service

Flat-blade screwdriver

#1 Phillips screwdriver, magnetic

#2 Phillips screwdriver, magnetic

#2 Phillips screwdriver, magnetic short-blade

Torx screwdrivers

Needlenose pliers

Diagonal side cutters

Spring hook

Feeler gauges

Analog or digital multimedia

Acronyms

ADF Automatic Document Feeder

CCD Charge-Couple Device

CCFL Cold Cathode Fluorescent Lamp

CDB Command Descriptor Blocks

CRU Customer Replaceable Unit

ESD Electrostatic Discharge

FRU Field Replaceable Unit

HV High Voltage

LCM Liquid Crystal Module

LED Light-Emitting Diode

LV Low Voltage

MFD Multi Function Device

PCBA Printed Circuit Board Assembly

PPM Page per minute

SPM Sides per minute

V ac Volts alternating current

V dc Volts direct current

Diagnostic information 2-1

4036-310, -311

Go Back

2. Diagnostic information

Start

This chapter describes two methods to solve the operational problems. The first relies on the scanner internal

diagnostics to report error codes. The second uses troubleshooting techniques to isolate the problem. In many

cases, the internal error codes will help you to locate the source of the problem quickly. If no error codes are

reported, or if the error codes do not locate the source of the problem, refer to the Symptom Tables.

• If you have an error message or user message, check the following:

— “Error codes and messages” on page 2-3

— “Service checks” on page 2-5

• Does the POR stop? Check the “Power-On Self Test (POST) sequence” on page 2-2.

• Do you have a symptom, rather than an error message? Check the “Symptom tables” on page 2-2.

• Additional information can be found at the following locations:

— “Understanding the operator panel and menus” on page 3-1

— “Accessing the service menus” on page 3-7

— “Service checks” on page 2-5

Note: There may be scanner error messages that are not contained in this service manual. Call your next level

of support for assistance.

CAUTION

Unplug all power from the electrical outlet before you connect or disconnect any cable or

electronic board or assembly for personal safety and to prevent damage to the scanner.

Disconnect any connections between the scanner and the printer.

2-2 Service Manual

4036-310, -311

Go Back

Power-On Self Test (POST) sequence

When you turn the printer and scanner on, it performs a Power-On Self Test. Check for correct POST functioning

by observing the following:

1. The printer LED (green light) turns on.

2. The operator panel turns on.

3. The operator panel displays counting the memory.

4. The operator panel displays a progression bar with the Lexmark splash logo.

5. You can hear the scanner doing a scanner calibration.

6. You can hear the printer starting up. It takes the printer longer to start up from a cold start rather than from

a warm start.

Symptom tables

The tables in this section provide detailed troubleshooting information.

Frequent paper jam, multifeed or skew See “Frequent paper jam, multifeed or skew” on page 2-5.

False multifeed See “False multifeed” on page 2-6.

The power does not come on, or

communication lost

See “The power does not come on” on page 2-7.

Voided line in scanned image (ADF or

Flatbed)

See “Voided line in scanned image (ADF or flatbed)” on

page 2-8.

Voids in flatbed scanned image See “Voids in flatbed scanned image” on page 2-8.

Image blank or distorted (flatbed) See “Image blank or distorted (flatbed)” on page 2-9.

Image blank or distorted (ADF-front side of

scanned page)

See “Image blank or distorted (ADF-front side of scanned

page)” on page 2-10.

Image blank or distorted (ADF-back side

of scanned page)

See “Image blank or distorted (ADF-back side of scanned

page)” on page 2-11.

Strange sound generated (ADF) See “Strange sound generated (ADF)” on page 2-11.

Strange sound generated (flatbed) See “Strange sound generated (flatbed)” on page 2-12.

Diagnostic information 2-3

4036-310, -311

Go Back

Error codes and messages

For information on error codes 910-999, refer to the printer’s service manual.

Error code Type Description Action

840.01 Scanner The scanner has been manually

disabled.

Enter the configuration menu to re-

enable the scanner.

840.02 Scanner The scanner has automatically

been disabled by the controller.

Enter the configuration menu to re-

enable the scanner.

841.XX Scanner The scanner image ASIC has

failed.

1.Check all connections on the

scanner engine board.

2.Replace the scanner engine

board assembly if problem

remains. See “Engine board

removal” on page 4-67.

3.Replace the controller board.

See “Controller board

removal” on page 4-58.

842.XX Scanner The controller board has lost

communication with the scanner

engine board.

1.Check all connections on the

scanner engine board.

2.Replace the scanner engine

board assembly if problem

remains. See “Engine board

removal” on page 4-67.

3.Replace the controller board.

See “Controller board

removal” on page 4-58.

843.XX Scanner The scanner carriage home

position detection failed.

1.Turn the machine off/on.

2.See the home position service

check.

844.00 Scanner The lower ADF scanner module

exposure lamp has failed.

Replace the lower ADF scan

module.

844.01 Scanner The upper ADF scanner module

exposure lamp has failed

Replace the upper ADF scan

module.

845.02 Scanner Lower scanner module cable has

failed

Replace the lower scanner module

cable.

845.03 Scanner Upper scanner module cable has

failed

Replace the upper scanner module

cable.

900.00-900.99

(except for

900.05)

Scanner An unrecoverable controller

board software error occurred

while an unknown process was

running.

See “900.xx System software

error” on page 2-13.

955.XX Scanner The Code ROM or NAND flash

failed the Cyclic Redundancy

Check (CRC), or the NAND

experienced an uncorrectible

multi-bit failure.

Replace the controller board. See

“Controller board removal” on

page 4-58.

2-4 Service Manual

4036-310, -311

Go Back

Paper jam error codes

For information on error codes 200-279, refer to the printer’s service manual.

Error code Type Description Action

280.06 Scanner Paper missing This error is caused by paper not

being detected at the ADF paper

present sensor. Check the sensor

for proper connection and possible

damage.

283.01 Scanner Scanner jam This is caused by paper being

detected by the media sensor at

start up. See “Frequent paper

jam, multifeed or skew” on

page 2-5.

283.03 Scanner Scanner jam This is caused by the paper jam

sensor not detecting movement of

reluctor wheel connected to the

paper jam idler roller at the right

time. See “Frequent paper jam,

multifeed or skew” on page 2-5.

283.05 Scanner Scanner jam This is caused by the paper jam

sensor detecting movement of the

reluctor wheel connected to the

paper jam idler roller for too long.

See“Frequent paper jam,

multifeed or skew” on page 2-5.

290.11 Scanner Scanner ADF cover open jam Occurs when the ADF cover open

sensor is opened during the middle

of a scan. Check sensor for proper

connection and possible damage.

295.20 Scanner Multifeed sensor on This is caused by the multifeed

sensor detecting the presence of

more than one sheet of paper. See

“False multifeed” on page 2-6.

La pagina si sta caricando...

Lexmark 6500E Manuale utente

Lexmark 6500E Manuale utente

in altre lingue

Documenti correlati

Altri documenti