ASROCK 939SLI32-ESATA2 Manuale del proprietario

11

1

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published February 2006

22

2

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 20 System Panel Header (PANEL1)

2 ATX Power Connector (ATXPWR1) 21 USB 2.0 Header (USB67, Blue)

3 ATX 12V Power Connector (ATX12V1) 22 Southbridge Controller

4 CPU Fan Connector (CPU_FAN1) 23 USB 2.0 Header (USB45, Blue)

5 939-Pin CPU Socket 24 Front Panel IEEE 1394 Header (FRONT_1394)

6 CPU Heatsink Retention Module 25 Infrared Module Header (IR1)

7 2 x 184-pin DDR DIMM Slots 26 Floppy Connector (FLOPPY1)

(Dual Channel A: DDR1, DDR2; Blue) 27 Game Port Header (GAME1)

8 2 x 184-pin DDR DIMM Slots 28 Front Panel Audio Header (HD_AUDIO1)

(Dual Channel B: DDR3, DDR4; Black) 29 Internal Audio Connector: CD1 (Black)

9 Northbridge Controller 30 PCI Slots (PCI1- 3)

10 Flash Memory 31 PCI Express x 16 Slot (PCIE3)

11 Primary IDE Connector (IDE1, Blue) 32 PCI Express x 4 Slot (PCIE2)

12 Secondary IDE Connector (IDE2, Black) 33 J9 / J10 Jumpers

13 Serial ATAII Connector (SATAII_BLACK) 34 PCI Express x 16 Slot (PCIE1)

14 Serial ATAII Connector (SATAII_BLUE) 35 SLI / XFIRE Power Connector

15 Chassis Fan Connector (CHA_FAN1) 36 Future CPU Port (FUTURE_CPU_PORT1)

16 Serial ATAII Connector (SATAII_RED) 37 J11 Jumper

17 Serial ATAII Connector (SATAII_ORANGE) 38 eSATAII Connector (eSATAII_BOTTOM)

18 Chassis Speaker Header (SPEAKER 1) 39 eSATAII Connector (eSATAII_TOP)

19 Clear CMOS Jumper (CLRTC1) 40 J1 / J2 / J3 / J4 / J5 / J6 / J7 / J8 Jumpers

33

3

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

ASRASR

ASR

ock eSock eS

ock eS

AA

A

TT

T

AII+1394 I/OAII+1394 I/O

AII+1394 I/O

1 Parallel Port 7 eSATAII Ports

2 IEEE 1394 Port 8 USB 2.0 Ports (USB01)

3 RJ-45 Port 9 USB 2.0 Ports (USB23)

4 Line In (Light Blue) 10 COM Port

5 Line Out (Lime) 11 PS/2 Keyboard Port (Purple)

6 Microphone (Pink) 12 PS/2 Mouse Port (Green)

44

4

ASRock 939SLI32-eSATA2 Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock 939SLI32-eSATA2 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock

website as well.

ASRock website http://www.asrock.com

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

1 x ASRock 939SLI32-eSATA2 Motherboard

(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)

1 x ASRock 939SLI32-eSATA2 Quick Installation Guide

1 x ASRock 939SLI32-eSATA2 Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

4 x Serial ATA (SATA) Data Cables (Optional)

2 x Serial ATA (SATA) HDD Power Cables (Optional)

1 x ASRock eSATAII+1394 I/O Shield

1 x ASRock SLI Bridge

EnglishEnglish

English

55

5

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm

CPU - 939-Pin Socket Supporting AMD Athlon

TM

64 / 64FX / 64X2

Processor

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

(see CAUTION 1)

- FSB 1000 MHz (2.0 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 2)

- Supports Hyper-Transport Technology

Chipset - Northbridge: ULi

®

M1695

- Southbridge: ULi

®

M1697

Memory - Dual Channel DDR Memory Technology (see CAUTION 3)

- 4 x DDR DIMM slots

- Support DDR400/333/266

- Max. capacity: 4GB

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 4)

- ASRock U-COP (see CAUTION 5)

- Boot Failure Guard (B.F.G.)

Expansion Slot - 1 x Future CPU Port (Supports CPU upgrade from AMD K8

939-Pin CPU to AM2 940-Pin CPU through AM2CPU Board)

(see page 11 for details)

- 3 x PCI slots

- 2 x PCI Express x 16 slots

- 1 x PCI Express x 4 slot

- Supports NVIDIA SLI

TM

Audio - Realtek ALC 660 5.1channel CODEC with High Definition

Audio

LAN - Gigabit LAN 10/100/1000 Mb/s

- PCIE x 1 Realtek RTL8111B

- Supports Wake-On-LAN

Rear Panel I/O ASRock eSATAII+1394 I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x IEEE 1394 Port

- 2 x eSATAII Ports

- 1 x RJ-45 LAN Port

- Audio Jack: Line in / Line out / Microphone

66

6

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

Connector - 4 x Serial ATAII 3.0Gb/s connectors, support RAID

(RAID 0, 1, 0+1, JBOD, 5) and “Hot Plug” functions

(see CAUTION 6)

- 2 x eSATAII 3.0Gb/s connectors (shared with 2 SATAII

connectors), support “Hot Plug” function (see CAUTION 7)

- 2 x ATA133 IDE connectors (support 4 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Game header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- SLI/XFIRE power connector

- CD in header

- Front panel audio connector

- Front panel IEEE 1394 header

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 8)

BIOS Feature - 2Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Hardware - CPU Temperature Sensing

Monitor - Motherboard Temperature Sensing

- CPU Overheat Shutdown to Protect CPU Life

- CPU Fan Tachometer

- Chassis Fan Tachometer

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

2000 / XP / XP 64-bit compliant

Certifications - FCC, CE, Microsoft

®

WHQL Certificated

77

7

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

CAUTION!

1. For power-saving’s sake, it is strongly recommended to enable AMD’s Cool ‘n’

Quiet

TM

technology under Windows system. See APPENDIX on page 51 of

“User Manual” in the Support CD to enable AMD’s Cool ‘n’ Quiet

TM

technology.

Since not all K8 939-pin CPU can support AMD’s Cool ‘n’ Quiet

TM

technology,

please check AMD’s website for details.

2. This motherboard supports Untied Overclocking Technology. Please read “Un-

tied Overclocking Technology” on page 28 for details.

3. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 9 for proper installation.

4. Although this motherboard offers stepless control, it is not recommended to

perform over-clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

5. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the motherboard

functions properly and unplug the power cord, then plug it back again. To

improve heat dissipation, remember to spray thermal grease between the

CPU and the heatsink when you install the PC system.

6. Before installing SATAII hard disk to SATAII connector, please read the

“SATAII Hard Disk Setup Guide” on page 24 to adjust your SATAII hard disk

drive to SATAII mode. Besides, you are allowed to downgrade the SATAII

hard disk to SATA hard disk (from SATAII 3Gb/s down to SATA 1.5Gb/s),

and connect it to the SATAII connector. You can also connect SATA hard

disk to SATAII connector directly.

7. This motherboard supports eSATAII interface, the external SATAII

specification. Please read “eSATAII Interface Introduction” on page 21 for

details about eSATAII and eSATAII installation procedures. (Port Multiplier

Technology is not supported with eSATAII interface on this motherboard.)

8. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 or SP2 / 2000 SP4.

88

8

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the car-

pet or the like. Also remember to use a grounded wrist strap or

touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a

grounded antstatic pad or in the bag that comes with the

component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the screws!

Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90° angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

99

9

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

2.2 Installation of Memory Modules (DIMM)2.2 Installation of Memory Modules (DIMM)

2.2 Installation of Memory Modules (DIMM)

939SLI32-eSATA2 motherboard provides four 184-pin DDR (Double Data Rate)

DIMM slots, and supports Dual Channel Memory Technology. For dual channel

configuration, you always need to install identical (the same brand, speed,

size and chip-type) DDR DIMM pair in the slots of the same color. In other words,

you have to install identical DDR DIMM pair in Dual Channel A (DDR1 and

DDR2; Blue slots; see p.2 No.7) or identical DDR DIMM pair in Dual Channel B

(DDR3 and DDR4; Black slots; see p.2 No.8), so that Dual Channel Memory

Technology can be activated. This motherboard also allows you to install four

DDR DIMMs for dual channel configuration, and please install identical DDR

DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration

Table below.

Dual Channel Memory Configurations

DDR1 DDR2 DDR3 DDR4

(Blue Slot) (Blue Slot) (Black Slot) (Black Slot)

(1) Populated Populated - -

(2) - - Populated Populated

(3)* Populated Populated Populated Populated

* For the configuration (3), please install identical DDR DIMMs in all four slots.

1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of blue slots

(DDR1 and DDR2), or in the set of black slots (DDR3 and DDR4).

2. If only one memory module or three memory modules are installed

in the DDR DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in DDR1

and DDR3, it is unable to activate the Dual Channel Memory Tech-

nology .

1010

10

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

STEP 1: Unlock a DIMM slot by pressing the retaining clips outward.

STEP 2: Align a DIMM on the slot such that the notch on the DIMM matches the

break on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

STEP 3: Firmly insert the DIMM into the slot until the retaining clips at both ends

fully snap back in place and the DIMM is properly seated.

1111

11

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

2.32.3

2.3

Expansion SlotsExpansion Slots

Expansion Slots

(Future CPU Port, PCI Slots and PCIE Slots)(Future CPU Port, PCI Slots and PCIE Slots)

(Future CPU Port, PCI Slots and PCIE Slots)

There are 1 Future CPU Port, 3 PCI slots and 3 PCI Express slots on 939SLI32-

eSATA2 motherboard.

Future CPU Port (Yellow-Colored Port):

Future CPU Port allows you to upgrade your AMD K8 939-Pin CPU to AM2 940-Pin

CPU by installing an add-on ASRock AM2CPU Board into this future CPU Port on

939SLI32-eSATA2 motherboard. Before you upgrade the K8 939-Pin CPU to AM2

940-Pin CPU, it is necessary to adjust the jumper settings for those required jumpers

on 939SLI32-eSATA2 motherboard. Please refer to the table below for the correct

jumper settings.

This yellow-colored Future CPU Port is not an AGP slot! Please do

NOT insert any AGP card into it!

CPU Type Jumper Settings

K8 939-Pin CPU

(Default)

AM2 940-Pin CPU

(Using add-on

ASRock AM2CPU

Board)

NOTE

When adjusting the jumper settings, you may use the tool, Jumper Cap Remover, to help you

removing the jumper caps more easily. This Jumper Cap Remover is bundled in your motherboard

package, and please follow the “Jumper Cap Remover Instruction” to use it properly.

J1 J2 J3 J4

J11

J9

J10

J5 J6

J7 J8

J1 J2 J3 J4

J11

J9

J10

J5 J6

J7 J8

1212

12

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots: PCIE1 / PCIE3 (PCIE x 16 slot) is used for PCI Express cards with x16

lane width graphics cards. PCIE2 (PCIE x 4 slot) is used for PCI

Express cards, such as Gigabit LAN card, SATA2 card, etc.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in

a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

This motherboard supports NVIDIA SLI

TM

technology. You can install one PCI Ex

press x 16 graphics card to PCIE1 and the other PCI Express x 16 graphics card

to PCIE3 to enable SLI

TM

feature. NVIDIA SLI

TM

technology is only supported with

Windows XP and XP 64-bit OS on this motherboard.

1313

13

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

2.4 SLI2.4 SLI

2.4 SLI

TMTM

TM

Operation Guide Operation Guide

Operation Guide

This motherboard supports NVIDIA SLI

TM

(Scalable Link Interface) technology that

allows you to install two identical NVIDIA SLI

TM

enabled PCI Express x 16 graphics

cards. Currently, NVIDIA SLI

TM

technology supports Windows XP and XP 64-bit

operating system. Please follow the installation procedures in this section.

SLI

TM

Technology Requirements

1. You should have two identical SLI

TM

-ready graphics cards that are NVIDIA

certified.

2. Make sure that your graphics card driver supports the NVIDIA

SLI

TM

technology. Download the latest driver from the NVIDIA website (www.

nvidia.com).

3. Make sure that your power supply unit (PSU) can provide at least the

minimum power required by your system.

Enjoy the benefit of SLIEnjoy the benefit of SLI

Enjoy the benefit of SLI

TMTM

TM

Step 1. Install the identical SLI

TM

-ready graphics cards that are NVIDIA certified

because different types of graphics cards will not work together properly.

(Even the GPU chips version shall be the same.) Insert one graphics card

into PCIE1 slot and another graphics card to PCIE3 slot. Make sure that the

cards are properly seated on the slots.

Step2. If required, connect an auxiliary power source to the PCI Express graphics

cards.

Step3. Align and insert the SLI Bridge to the goldfingers on each graphics card.

Make sure that the SLI Bridge is firmly in place.

1414

14

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

Step4. Connect a VGA cable or a DVI-I cable to the monitor connector and the DVI

connector of the graphics card that is inserted to PCIE1 slot.

Step5. Connect a 4-pin ATX power cable to SLI/XFIRE power connector.

Step6. Power on your computer and boot into OS. Install the “SLI Enabled” driver

of our support CD to your system. Then, reboot your system.

Step7. Install the graphics card drivers to your system. After that, you can enable

the Multi-Graphics Processing Unit (GPU) feature in the NVIDIA nView sys-

tem tray utility. Please follow the below procedures to enable the multi-GPU

feature.

A. Click the NVIDIA Settings icon on your Windows taskbar.

B. From the pop-up menu, select nView Desktop Manager, and then

click nView Properties.

C. From the nView Desktop Manager window, select the Desktop

Management tab.

D. Click Properties to display the Display Properties dialog box.

1515

15

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

E. From the Display Properties dialog box, select the Settings tab then click

Advanced.

F. Select the NVIDIA GeForce tab.

G. Click the slider to display the following screen, then select the SLI

multi-GPU item.

H. Click the Enable SLI multi-GPU check box.

I. Click OK when done.

* SLI

TM

appearing here is a registered trademark of NVIDIA Technologies Inc., and is used only

for identification or explanation and to the owners’ benefit, without intent to infringe.

1616

16

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

Short Open

Clear CMOSDefault

2.52.5

2.5

Jumpers SetupJumpers Setup

Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper

(CLRTC1)

(see p.2, No. 19)

Note: CLRTC1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3

on CLRTC1 for 5 seconds.

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

•

Floppy Connector

(33-pin FLOPPY1)

(see p.2 No. 26)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

the red-striped side to Pin1

1717

17

ASRock 939SLI32-eSATA2 Motherboard

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

connect the black end

to the IDE devices

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2 No. 11) (39-pin IDE2, see p.2 No. 12)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

SATAII_RED and SATAII_ORANGE connectors can be used for internal

storage devices or be connected to eSATAII_BOTTOM and eSATAII_TOP

connectors with corresponding color to support eSATAII devices. Please

read “eSATAII Interface Introduction” on page 21 for details about eSATAII

and eSATAII installation procedures.

eSATA II Connectors These two eSATA II

(eSATAII_TOP: see p.2, No. 39) connectors support SATA

(eSATAII_BOTTOM: see p.2, No. 38) data cables for external

SATAII function. The current

eSATA II interface allows up to

3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA /

SATAII hard disk or the SATAII

connector on the motherboard.

You can also use the SATA data

cable to connect SATAII connec-

tors and eSATAII connectors

with corresponding color.

Serial ATA II Connectors These four Serial ATA II

(SATAII_BLUE: see p.2, No. 14) (SATAII) connectors support

(SATAII_BLACK: see p.2, No. 13) SATA data cables for internal

(SATAII_RED: see p.2, No. 16) storage devices. The current

(SATAII_ORANGE: see p.2, No. 17) SATA II interface allows up to

3.0 Gb/s data transfer rate.

eSATAII_TOP

eSATAII_BOTTOM

SATAII_BLACK

SATAII_BLUE

SATAII_ORANGE

SATAII_RED

EnglishEnglish

English

1818

18

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

CD1

connect to the

power supply

connect to the SATA

HDD power connector

Front Panel Audio Header This is an interface for front

(9-pin HD_AUDIO1) panel audio cable that allows

(see p.2 No. 28) convenient connection and

control of audio devices.

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header ASRock eSATAII+1394 I/O

(9-pin USB67) accommodates 4 default USB

(see p.2 No. 21) 2.0 ports. Ifthose USB 2.0 ports

on the I/O panel are not sufficient,

thisUSB 2.0 header is available

to support 2 additional USB 2.0

ports.

USB 2.0 Header ASRock eSATAII+1394 I/O

(9-pin USB45) accommodates 4 default USB

(see p.2 No. 23) 2.0 ports. Ifthose USB 2.0 ports

on the I/O panel are not sufficient,

thisUSB 2.0 header is available

to support 2 additional USB 2.0

ports.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 25) and receiving infrared module.

Internal Audio Connectors This connector allows you

(4-pin CD1) to receive stereo audio input

(CD1: see p.2 No. 29) from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

1919

19

ASRock 939SLI32-eSATA2 Motherboard

ATX 12V Connector Please connect an ATX 12V

(4-pin ATX12V1) power supply to this connector.

(see p.2 No. 3)

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 20) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 18)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 15) match the black wire to the

ground pin.

CPU Fan Connector Please connect a CPU fan cable

(3-pin CPU_FAN1) to this connector and match

(see p.2 No. 4) the black wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 2)

1. High Definition Audio supports Jack Sensing, but the panel wire on the

chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio

header as below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

D. Enter BIOS Setup Utility. Enter Advanced Settings, and then select

Chipset Configuration. Set the Front Panel Control option from

[Auto] to [Enabled].

E. Enter Windows system. Click the icon on the lower right hand

taskbar to enter Realtek HD Audio Manager. Click “Audio I/O”, select

“Connector Settings” , choose “Disable front panel jack

detection”, and save the change by clicking “OK”.

EnglishEnglish

English

2020

20

ASRock 939SLI32-eSATA2 Motherboard

EnglishEnglish

English

SLI/XFIRE_POWER1

SLI/XFIRE Power Connector It is not necessary to use this

(4-pin SLI/XFIRE_POWER1) connector, but please connect it

(see p.2 No. 35) with a hard disk power connecor

when two graphics cards are

plugged to this motherboard at

the same time.

Game Port Header Connect a Game cable to this

(15-pin GAME1) header if the Game port bracket

(see p.2 No. 27) is installed.

IEEE 1394 Header This motherboard accommo-

(9-pin FRONT_1394) dates 2 IEEE 1394 ports, includ-

(see p.2 No. 24) ing 1 Ready-to-UseIEEE 1394

port on ASRock eSATAII+1394

I/O and 1 onboard header sup-

porting 1 extra IEEE 1394 port.

La pagina sta caricando ...

ASROCK 939SLI32-ESATA2 Manuale del proprietario

ASROCK 939SLI32-ESATA2 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti