Tyan S7012 Manuale utente

1

http://www.tyan.com

S7012

Version 1.1

Copyright

®

is a

registered trademark of MiTAC International Corporation.

Trademark

All registered and unregistered trademarks and company names contained in this

manual are property of their respective owners including, but not limited to the

following.

TYAN

®

is a trademark of MiTAC International Corporation.

Intel

®

Nehalem-EP Series and combinations thereof are trademarks of Intel

Corporation.

AMI, AMI BIOS are trademarks of AMI Technologies.

Microsoft, Windows are trademarks of Microsoft Corporation.

SuSE is a trademark of Novell.

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.

Notice

Information contained in this document is furnished by MiTAC International

Corporation and has been reviewed for accuracy and reliability prior to printing.

MiTAC assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN products including liability or

warranties relating to fitness for a particular purpose or merchantability. MiTAC

retains the right to make changes to product descriptions and/or specifications at

any time, without notice. In no event will MiTAC be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

2

http://www.tyan.com

Table of Contents

Check the box contents! 3

Chapter 1: Introduction

1.1 Congratulations 5

1.2 Hardware Specifications 5

1.3 AST2050 Application 6

Chapter 2: Board Installation

2.1 Board Image 8

2.2 Block Diagram 9

2.3 Board Parts, Jumpers and Connectors 10

2.4 Installing the Processor and Heatsink 20

2.5 Thermal Interface Material 23

2.6 Finishing Installing the Heatsink 24

2.7 Tips on Installing Motherboard in Chassis 25

2.8 Installing the Memory 26

2.9 Attaching Drive Cables 29

2.10 Installing Add-in Cards 30

2.11 Installing I/O Shield 31

2.12 Connecting External Devices 32

2.13 Installing the Power Supply 33

2.14 Finishing up 33

Chapter 3: BIOS Setup

3.1 BIOS Main Menu 37

3.2 Advanced Menu 38

3.3 PCI PnP Menu 64

3.4 Boot Menu 66

3.5 Security Menu 70

3.6 Chipset Menu 71

3.7 Exit Menu 76

Chapter 4: Diagnostics

4.1 Beep Codes 77

4.2 Flash Utility 77

4.3 AMI BIOS Post Code 78

Glossary

81

Technical Support

87

3

http://www.tyan.com

Check the box contents!

1x S7012 motherboard

2 x mini SAS Cable (optional)

6 x Serial ATA Cable

1 x USB2.0 cable

1 x S7012 User’s Manual

1 x S7012 Quick Reference Guide

1 x I/O Shield Installation Guide

1 x TYAN Installation CD

1 x I/O shield

If any of these items are missing, please contact your vendor/dealer for

replacement before continuing with the installation process.

4

http://www.tyan.com

NOTE

5

http://www.tyan.com

Chapter 1: Introduction

1.1 - Congratulations

You have purchased one of the most powerful server solutions. Based on Intel

®

5520 and ICH10R chipsets, the S7012 is designed to support up to two Nehalem-

EP Series processors and up to 144GB DDR3-800/1033/1066/1333 memory,

providing a rich feature set and incredible performance. Leveraging advanced

technology from Intel, the S7012 is capable of offering scalable 32 and 64-bit

computing, high-bandwidth memory design, and lightning-fast PCI-E bus

implementation.

The S7012 not only empowers your company in today’s demanding IT environment

but also offers a smooth path for future application usage. All of this provides the

S7012 the power and flexibility to meet the needs of nearly any server application.

Remember to visit TYAN’s Website at http://www.tyan.com. There you can find

information on all of TYAN’s products with FAQs, online manuals and BIOS

upgrades.

1.2 - Hardware Specifications

Supported CPU Series

Intel Xeon Processor 5500 Series

Socket Type / Q'ty LGA1366 / (2)

Thermal Design

Power (TDP) wattage

Max up to 130W

Processor

System Bus

Up to 4.8/ 5.86/ 6.4GT/s with Intel QuickPath Interconnect

(QPI) support

IOH / ICH Intel 5520 / ICH10R

Chipset

Super I/O Winbond W83627DHG

Supported DIMM Qty (18) DIMM slots

DIMM Type / Speed

DDR3 800/1066/1333* RDIMM/UDIMM / * limit 1 per

channel for 1333MHz speed

Capacity Up to 144GB at launch w/ dual rank RDIMMs

Memory channel 3 Channels per CPU

Memory

Memory voltage 1.5V

Expansion

Slots

PCI-E (1) PCI-E x8 slot (w/ x4 link) / (4) PCI-E Gen.2 x8 slots

Port Q'ty (4)

LAN

Controller Intel 82574L / Intel 82576EB

Connector (2) Mini-SAS connectors (totally support 8 ports)

Controller LSI SAS1068E

Speed 3.0 Gb/s

SAS

(optional)

RAID RAID 0/1/1E (LSI Integrated RAID)

Connector (6) SATA

Controller ICH10R

Speed 3.0 Gb/s

Storage

SATA

RAID RAID 0/1/10/5 (Intel Matrix RAID)

Graphic Connector type D-Sub 15-pin

6

http://www.tyan.com

Resolution 1600x1200@60Hz

Chipset Aspeed AST2050

USB (7) USB2.0 ports (4 at rear, 2 via cable, 1 type A onboard)

COM (1) port (rear)

SAS (2) Mini-SAS (4-in-1) connectors

VGA (1) D-Sub 15-pin VGA port

RJ-45 (4) GbE ports

Power SSI 24-pin + 8-pin + 8-pin power connectors / EPS12V

Front Panel (1) 2x12-pin SSI front panel header

Input /Output

SATA (6) SATA-II connectors

Chipset Winbond W83793G

Voltage Monitors voltage for CPU, memory, chipset & power supply

Fan Total (5) 4-pin headers / Total (5) 8-pin headers

Temperature Monitors temperature for CPU & system environment

System

Monitoring

Others Chassis intrusion detection / Watchdog timer support

Onboard Chipset Onboard Aspeed AST2050

AST2050 IPMI

Feature

IPMI 2.0 compliant baseboard management controller

(BMC) / Supports storage over IP and remote platform-

flash/ BIOS update / USB 2.0 virtual hub

Server

Management

AST2050 iKVM

Feature

24-bit high quality video compression / Dual 10/100 Mb/s

MAC interfaces

Brand / ROM size AMI / 4MB

BIOS

Feature

Plug and Play (PnP) /PCI2.3 /WfM2.0 /SMBIOS2.3 /PXE

boot / ACPI 2.0 power management /Power on mode after

power recovery / User-configurable H/W monitoring / Auto-

configurable of hard disk types / Multiple boot options

Form Factor SSI EEB

Form Factor

Board Dimension 12"x13" (305x330mm)

Operating

System

OS supported list

Please refer to our OS supported list.

http://www.tyan.com/tech/os_support1.aspx

FCC (DoC) Class B

Regulation

CE (DoC) Yes

Operating Temp. 10° C ~ 35° C (50° F~ 95° F)

Non-operating Temp. - 40° C ~ 70° C (-40° F ~ 158° F)

Operating

Environment

In/Non-operating

Humidity

90%, non-condensing at 35° C

RoHS RoHS 6/6 Complaint Yes

Motherboard (1) S7012 Motherboard

Manual (1) User's manual / (1) Quick Ref. Guide (1) IO Shield QR

Installation CD (1) TYAN installation CD

I/O Shield (1) I/O Shield

SATA (6) SATA signal cables

SAS (2) Mini-SAS (2x SFF-8470) cables

Package

Contains

Cable

USB (1) CCBL-035J, 2-port USB bracket cable

Riser Card M2091, PCI-E 1U riser card (left)

Optional

accessories for

future

upgrade

Cable

(1) CCBL-0615, COM port bracket cable / (1) CCBL-0311,

SATA 1-to-2 power cable / (1) CCBL-035J, 2-port USB

bracket cable

1.3 - AST2050 Application

Please visit the TYAN Web Site at http://www.tyan.com to download the latest

AST2050 User’s Guide.

7

http://www.tyan.com

Chapter 2: Board Installation

You are now ready to install your motherboard. The mounting hole pattern of the

S7012 matches the SSI EEB specification. Before continuing with installation,

confirm that your chassis supports an SSI EEB motherboard.

How to install our products right… the first time

The first thing you should do is reading this user’s manual. It contains important

information that will make configuration and setup much easier. Here are some

precautions you should take when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the

antistatic bag. Unplug the power from your computer power supply and

then touch a safely grounded object to release static charge (i.e. power

supply case). For the safest conditions, TYAN recommends wearing a

static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the

board, or flex the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors,

memory modules, and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic

bag that the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your

chassis, as well as installing the processor, memory, disk drives and cables.

NOTE

DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN

DAMAGED.

8

http://www.tyan.com

2.1- Board Image

S7012

This picture is representative of the latest board revision available at the time of

publishing. The board you receive may or may not look exactly like the above

picture.

9

http://www.tyan.com

2.2 - Block Diagram

S7012

10

http://www.tyan.com

2.3 - Board Parts, Jumpers and Connectors

This diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above diagram.

Jumper Legend



OPEN - Jumper OFF, without jumper cover



CLOSED – Jumper ON, with jumper cover

11

http://www.tyan.com

Jumper/Connector Function

J9 (TYFP1) Standard Front Panel Connector

J16 BMC I

2

C Bus Header

J34 USB Front Panel Header (blue)

J18 COM2 Connector

J24 PSMI Connector

J6 Chassis Intrusion Header

J35 CPLD JTAG Header

USB3 Type-A USB Connector

J33 ICH SGPIO Header

J15 Port 80 Header

J41/J42/J43/J44/J45 8-pin 4056 Fan Connector (reserved for BB)

J2/J8/J36/J37/J38 4-pin Fan Connector

J39/J40 Reset Switch/Power Switch

J3

LSI 1068E Enable/Disable Jumper

Pin 1-2 closed: Enable (Default)

Pin 2-3 closed: Disable

J7

BMC Reset Jumper

NC: Default

Pin 1-2 closed: Disable BMC

JP3

Clear CMOS Jumper

Pin 1-2 closed: Normal (Default)

Pin 2-3 closed: Clear

JP1/JP2

COM2 Switch Jumper

Pin 1-2 closed: SIO to COM2 (Default)

Pin 2-3 closed: BMC UART2 to COM2

JP4

LSI 1068E Device ID Select Jumper

Pin 1-2 closed: (Default)

Pin 2-3 closed: Device ID bit [0]=0b1

12

http://www.tyan.com

J18

(From left to right)

SATA5/SATA4/SATA3/SATA2/SATA1/SATA0

J34

J16

J15

13

http://www.tyan.com

J18: COM2 Connector

1

2

1

0

9

Pin Signal Pin Signal

1 DCD 2 DSR

3 RXD 4 RTS

5 TXD 6 CTS

7 DTR 8 RI

9 GND 10 KEY

J15: PORT 80 Header

1

2

1

3

1

4

Pin Signal Pin Signal

1 NC 2 V3P3

3 NC 4 FRAME

5 CLK_33M 6 GND

7 GND 8 LAD3

9 PLTRST 10 LAD2

11 NC 12 LAD1

13 NC 14 LAD0

J16: BMC I

2

C Header

1

Pin Signal Pin Signal

1 IPMB_DAT 2 GND

3 IPMB_CLK 4 NC

J34: USB Front Panel Header (Blue)

10

9

2

1

Pin Signal Pin Signal

1 +5V 2 +5V

3 USB D- 4 USB D-

5 USB D+ 6 USB D+

7 GND 8 GND

9 KEY 10 GND

SATA0/1/2/3/4/5: Serial ATA Connector

7 GND

6 RXP

5 RXN

4 GND

3 TXN

2 TXP

7

1

1 GND

Connects to the Serial ATA ready drives via the

Serial ATA cable.

SATA0: J30 SATA1: J29

SATA2: J26 SATA3: J23

SATA4: J22 SATA5: J21

14

http://www.tyan.com

J6: Chassis Intrusion Header

1

Pin Signal Pin Signal

1 INTRUDER# 2 GND

J24

J38

J36

J9

J37

J8

J2

J6

J41

J42

J43

J44

J45

15

http://www.tyan.com

J9 (TYFP1): Standard Front Panel Connector

24

23

2

1

NOTE1: +3.3V power rail is IDLED, WLED (Warning LED), LANLED

NOTE2: +5V power rail is PWRLED, HDLED

J24: PSMI Connector

1

Pin Signal Pin Signal

1 SMB_CLK 2 SMB_DAT

3 SMBALERT 4 GND

5 V3P3

J2/J8/J36/J37/J38: 4-pin Fan Header

+12V

PWM Control

GND

Tachometer

1

+12V

PWM Control

GND

Tachometer

1

Use this header to connect the cooling

fan to your motherboard to keep the

system at optimum performance levels.

J2: Rear 1 FAN

J8: CPU0FAN

J36: Front 2 FAN

J37: Front 1 FAN

J38: CPU1FAN

J41/J42/J43/J44/J45: 8-pin 4056 Fan Header (reserved for barebone)

J41: Sys5 FAN & Sys10 FAN

J42: Sys4 FAN & Sys9 FAN

J43: Sys3 FAN & Sys8 FAN

J44: Sys2 FAN & Sys7 FAN

J45: Sys1 FAN & Sys6 FAN

Pin Signal Pin Signal

1 PWM1 2 +12V

3 TACH1 4 GND

5 GND 6 TACH2

7 +12V 8 PWM2

PIN1 PIN3 PIN5 PIN7

PWRLED+ KEY PWRLED- HDLED+

PIN2 PIN4 PIN6 PIN8

+5VSB IDLED+ IDLED- WLED-

PIN9 PIN11 PIN13 PIN15

HDLED- PWRSW+ GND RSTSW

PIN10 PIN12 PIN14 PIN16

PSI_BMC_R- LAN1LED+ LAN1LED- SMBDAT

PIN17 PIN19 PIN21 PIN23

GND IDLED_SW TEMP-SENSOR NMI_SW-

PIN18 PIN20 PIN22 PIN24

SMBCLK INTRD# LAN2LED+ LAN2LED-

16

http://www.tyan.com

J35

USB3 J33

JP3

JP2

JP1

17

http://www.tyan.com

USB3: Type-A USB Connector

Pin Signal Pin Signal

1 +5V 2 USB D-

3 USB D+ 4 GND

J33: ICH SGPIO Header

1

0

2

9

1

Pin Signal Pin Signal

1 SMBCLK 2 SDATAOUT0

3 SMBDAT 4 SDATAOUT1

5 GND 6 SLOAD

7 KEY 8 SCLOCK

9 NC 10 NC

J35: CPLD JTAG Header

1

0

9

2

1

Pin Signal Pin Signal

1 JTAG_TCK 2 GND

3 JTAG_TDO 4 +3.3V

5 JTAG_TMS 6 NC

7 NC 8 KEY

9 JTAG_TDI 10 GND

JP3: Clear CMOS Jumper

3

1

Normal

(Default)

1

3

Clear

Use this jumper when you forgot your system/setup

password or need to clear system BIOS setting.

How to clear the CMOS data

- Power off system and disconnect power

supply from AC source

- Use jumper cap to close Pin_2 and 3 for

several seconds to Clear CMOS

- Replace jumper cap to close Pin_1 and 2

Reconnect power supply to AC source

Power on system

JP1/JP2: COM2 Switch Jumper

3

1

Pin 1-2 Closed: SIO to COM2 (Default)

1

3

Pin 2-3 Closed: BMC UART2 to COM2`

18

http://www.tyan.com

J1

J7

J3

19

http://www.tyan.com

J7: BMC Reset Jumper

1

Pin 1-2 Open: Enable BMC(Default)

1

Pin 1-2 Closed: Disable BMC

J1: LSI 1068E Device ID Select Jumper

1

3

Pin 1-2 Closed: LSI 1068E Device ID (Default)

1

3

Pin 2-3 Closed: :LSI 1068E Device ID – Device ID bit

[0] =0b1

J3: LSI 1068E Enable/Disable Jumper

3

1

Pin 1-2 Closed: Enable LSI 1068E (Default)

1

3

Pin 2-3 Closed: Disable LSI 1068E

20

http://www.tyan.com

2.4 - Installing the Processor and Heat Sink

Your S7012 supports the latest processor technologies from Intel

®

. Check the

TYAN website for latest processor support:

http://www.tyan.com

Processor Installation (LGA1366 Socket)

The processor should be installed carefully. Make sure you are wearing an antistatic

strap and handle the processor as little as possible. Please note that both

processors of the same type and frequency are required for optimal system

performance.

NOTE: TYAN is not liable for damage as a result of operating an unsupported

configuration.

Follow these instructions to install your processor.

The diagram is provided as a visual guide to help you install the socket processor

and may not be an exact representation of the processor you have.

Step 1: Take off the CPU protection cap.

Step 2: Pull the CPU lever up to unlock the CPU socket (A). Then open the

socket in the direction as shown (B).

Step 3: Place the CPU on the CPU socket, ensuring that pin 1 is located in the

right direction.

La pagina sta caricando ...

Tyan S7012 Manuale utente

Questo manuale è adatto anche per

Tyan S7012 Manuale utente

in altre lingue

Documenti correlati

Altri documenti