NAMRON ZIGBEE PLUGG MED TERMOSTAT 70110005

Important: Read All Instructions P rior to Installation

Pro du c t Data

3. Z igbee Network Pairing through C oordinator o r Hu b ( Added to a Zigbee Network)

4. T o u c hLin k to a Zigbee Remo te

< 10cm

Note: 1 ) Di rec tly To u c hLin k ( both n ot added to a Z igBee n etwork), eac h d evic e c an l ink with 1 r emote.

4 ) After Tou c hLin k, the devic e c an b e c ontrolled b y the l inked remotes .

2 ) Touc hL ink after b oth added to a Z igBee n etwork, eac h d evic e c an l ink with m ax. 3 0 remo tes .

fail. Plea se refer to the part " F ac to ry Res et Manu all y".

S tep 2 : From your ZigBee Controller or hub interfa ce, choose to add lighting device and enter P airing mode a s

instructed by the controller.

S tep 3 : S hort press “Program” button 5 times continuously to set the device to network pa iring mode, LED

indica tor will fla sh white fast.

S tep 1 : Short press “P rog” button 4 times ( Or re- power on the device 4 times) to sta rt Touchlink commissioning,

180S timeout. Once timeout, repeat the operation.

S tep 2 : Bring the remote or touch panel within 10cm of the lighting device.

S tep 3 : S et the remote or touch pa nel into Touchlink commissioning,

Func tion i ntrodu c tio n

Radio Frequency

Relative humidity

Over Current Protection

16A

2.4G Hz

114.8×54.8×74.7(mm)

0x000A(Plug-in Unit)

Over current

Stays solid ora nge

Flashes red slowly

Stays solid cya n

• Z igBee sma rt plug ba sed on la test ZigBee 3.0 protocol

• S upports find and bind mode to bind a Z igBee remote

• Supports zigbee green power and can bind max. 20 zigbee green power switches

• Supports temperature measurement

• S upports over current protection a nd power metering, ena bles to report power consumption to gatewa y

• ZigBee end device that supports Touchlink commissioning

• Waterproof gra de: IP 20

• E nables to control ON/OF F o f the loa d, supports max. 16 scenes

S afety & Warn ings

Operation

6. F actory R es et Manu ally

S tep 1 : Short press the “progra m” button 5 times continuously, the plug will enter into network pairing mode.

8. F ind and B ind Mode

S tep 1 : Short press “P rog.” button 3 times to sta rt Find a nd Bind mode (LE D indica tor fla shes white slowly) to

find and bind target node, 180 seconds timeout, repea t the opera tion.

S tep 2 : Set the remote or touch pa nel (ta rget node) i nto find a nd bind mode, and enable it

S tep 3 : There shall be indication on the remote or touch pa nel that it bind the device

Note: Make sure the device already a dded to a n etwork, the remote added to the same one or not added to any

network.

Zigbee

Remote

S tep 1 : Short press “P rogra m” button 4 times to start Learning to GP switch mode ( LED indica tor flashes twice) ,

180 seconds timeout, repeat the operation.

Step 1: S hort press “P rogra m” button 3 times to sta rt delete Learning to GP switch mode ( LE D indicator fla shes

slowly), 180 seconds timeout, repeat the operation.

50/60Hz

Inpu t Clu s ters

• 0x0000: Basic • 0x0003: Identify • 0x0004: Groups • 0x0005: Scenes • 0x0006: On/off

• 0x0702: S imple Metering • 0x0b04: Electrical Measurement

• 0x0b05: Diagnostics

Output Clu s ters

• 0x0003: Identify

1 2. Z igB ee C lus ters t h e d evic e s upports a re as f ollows :

1 3. O TA

The device supports firmwa re upda ting through OTA, and will a cquire new firmware from zigbee controller or

hub every 10 minutes automa tically.