ProLights Single source multipurpose LED PAR available in TU, DY and UV version Manuale utente

Marca: ProLights

Modello: Single source multipurpose LED PAR available in TU, DY and UV version

Categoria: Proiettori

Tipo: Manuale utente

EN - IT

USER MANUAL

MANUALE UTENTE

ECLIPSEPAR

SINGLE SOURCE MULTIPURPOSE LED PAR

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV. 01-02/19

ECLIPSEPARTU-DY-UV

Packing content

• ECLIPSEPARTU-DY-UV

• User manual

• Power cable

• Additional optics: 24° (on board - for TU and DY

versions), 12° and 65° lens included (for TU and DY

versions); 40° lens optional (for TU and DY versions)

- gel frame holder included (for TU and DY versions),

egg crate optional

• Other: for the UV version only the 40 ° lens is included.

No other optics or accessories are available and

should not be mounted for this version

TABLE OF

CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description and specications

1. 2 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 DMX mode

3. 5 DMX conguration

3. 6 Setting

3. 7 Channels DMX

3. 8 Fixture settings

Led frequency

Factory Reload

3. 9 Fixture Information

3. 10 Operations in automatic mode

Master/Slave

Eects

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting

ECLIPSEPARTU-DY-UV

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

ECLIPSEPARTU-DY-UV

- 1 - INTRODUCTION

1.1 ECLIPSEPARTU-DY-UV - DESCRIPTION AND TECHNICAL SPECIFICATIONS

ECLIPSEPAR is a range of multipurpose LED xtures with a single source, delivering silent operation, high

quality of light and optical exibility, designed to redene the standard for theatrical, TVs and corporate

applications.

ECLIPSEPARTU and DY features a 177W white LED source (3200K TU; 6000K DY) delivering a tremendous

lumen output and superior light quality with CRI and R9 > of 95.

ECLIPSEPARUV is a real UV LED luminaire with a 365nm wavelength LED source.

The xture oers an extensive accessory range including barn doors, lter frame, egg crate and a multi-

tude of interchangeable lenses.

ECLIPSEPAR features a smooth 16bit dimming as well as RDM control and adjustable PWM to look good

in front of a camera.

LIGHT SOURCE

• Source: 177 W white LED / 108W UV LED

• CT: (TU) 3200K - (DY) 6000K

• CRI: > 96 for TU and DY versions

• R9: > 95 for TU and DY versions

• Luminous ux: (TU) 12°: 13526 lm - 24°: 13638 lm - 65°: 12376 lm; (DY) 12°: 13571 lm - 24°: 13453 lm -

65°: 12247 lm; (UV) 229.07lm

• Lux: (TU) 12°: 15200 lux - 24°: 6560 lux - 65°: 1220 lux; (DY) 12°: 16500 lux - 24°: 6860 lux - 65°: 1230 lux;

(UV) 15.9lux @3m

• Lux: (TU) 12°: 5472 lux - 24°: 2361.6 lux - 65°: 439.2 lux; (DY) 12°: 5940 lux - 24°: 2469.9 lux - 65°: 442.8

lux; (UV) 5.724lux @5m

• Source life expectancy: >70.000 h

• Other: >85 TLCI, 90/99 TM30 for TU and DY; 365nm for UV LED

OPTICS

• Beam angle: 10° / 23° / 69° with dierent lens included°

• Field angle: 27° / 40° / 97° with dierent lens included°

• Lens diameter: (24°) 162.5 - (65°) 163mm

• Lens type: fresnel lens

• Additional optics: 24° (on board - for TU and DY versions), 12° and 65° lens included (for TU and DY ver-

sions); 40° lens optional (for TU and DY versions) - gel frame holder included (for TU and DY versions),

egg crate optional

• Other: 40° lens only included on board in UV version; no other lens or accessories availables for UV

version

DYNAMIC EFFECTS

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of dimmer and strobe

• Auto mode: built-in programs with execution speed adjustment

BODY

• Body: aluminiumdie-casting

• Body colour: black

ECLIPSEPARTU-DY-UV

Fig.1 - Technical drawingECLIPSEPARTU-DY-UV

CONTROL

• Protocols: DMX512, RDM

• DMX channels: 1 / 2 / 3 / 6channel

• RDM: RDM ready for xture remote monitor and settings

• Display: OLED display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Dimmer curves: dierent dimming curves available

• Strobe / shutter: 0 - 30 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

• Selectable PWM: 600~25K Hz

ELECTRICAL

• Power consumption: (TU, DY) 207 W - (UV) 107 W

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): (TU, DY) 207 W - (UV) 127W

• Power consumption (at 120V): (TU, DY) 211 W - (UV) 134W

• Output (at 230V): (TU, DY) 12 - (UV) 16 pcs units on a single power line

• Output (at 120V): (TU, DY) 6 - (UV) 8 units on a single power line

• Power factor: pF 0.99 @ 120V - pF 0.94 @ 230V

PHYSICAL

• Cooling: forced air with low noise fan

• Sospension and xing: any position with quick-lock omega brackets

• Signal connection: Amphenol XLR 3p + 5p IN/OUT connectors

• Power connection: Neutrik powerCON IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 316x318x404mm

• Weight: 5.5kg

316mm/12,44in 318mm/12,52in

404mm/15,91in

ECLIPSEPARTU-DY-UV

Fig.2

ECLIPSEPARTU-DY-UV

1.2 OPERATING ELEMENTS AND CONNECTIONS

1. LOCKING KNOB for mounting bracket.

2. MOUNTING BRACKET.

3. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them.

4. DMX IN (3-pole XLR): 1 = ground, 2 = DMX -,

3 = DMX +.

5. DMX OUT (3-pole XLR): 1= ground, 2 = DMX

-, 3 = DMX +.

6. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3

= DMX+, 4 N/C, 5 N/C.

7. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-,

3 = DMX+, 4 N/C, 5 N/C.

8. POWER IN (PowerCON IN): for connection to a

socket (100-240V~/50-60Hz) via the supplied

mains cable.

9. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only.

10. POWER OUT (PowerCON OUT): power output

for connection of multiple units in series.

Fig.3

ECLIPSEPARTU-DY-UV

- 2 - INSTALLATION

2.1 MOUNTING

ECLIPSEPARTU-DY-UV may be set up on a solid and even surface. The unit can also be mounted upside

down to a cross arm. For xing, stable mounting clips are required. The mounting place must be of suf-

cient stability and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location by means of the mounting bracket .

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the knob to slightly release or tighten the locking mechanism of the

bracket if is necessary .

NOTE - For the installation of the projector ECLIPSEPARTU-DY-UV insert the hook to stare it to a suspended

system.

MENU UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

ECLIPSEPARTU-DY-UV

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

To turn on the ECLIPSEPARTU-DY-UV connect the supplied main cable to a socket (100-240 VAC-50/60

Hz). Then the unit is ready for operation and can be operated via a DMX controller or it independently

performs its show program in succession.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

It is the responsibility of the installer to ensure the electrical, mechanical and thermal compatibility of the

track system and the ttings. The connection to the main network of electric distribution must be carried

out by a qualied electrical installer.

ATTENTION - Make sure to remove the tension of feeding before beginning any intervention of mainte-

nance.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the LED Display

(g.4).

Fig.4- Functions of the buttons

1 CONNECT

DMX Address

Value (001-512)

DMX Mode

1 Ch

2 Ch

3 Ch

6 Ch

2 SETUP

Screen

Back Light

10S

20S

30S

Flip Display

NO-Yes

Key Lock

NO-Yes

3 ADVANCED

Dimmer Mode

O

Dimmer 1

Dimmer 2

Dimmer 3

Led Frequency

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Fan Mode

Auto

O

Silent

Factory Reload

NO-Yes

4 INFORMATION

Fixture Hours

0-9999

Version

V1.0

UID

15D0022****

5 STANDALONE

Master/Slave

Eects

Eect 1 Speed 1~100

Eect 2

Eect 3

Static

Dimmer (000-255)

Strobe (000-255)

ECLIPSEPARTU-DY-UV

3.3 MENU STRUCTURE

Number

DMX

channels

Address of

start (example)

DMX address

occupied

Next possible start address

for unit No. 1

Next possible start address

for unit No. 2

Next possible start address

for unit No. 3

6 33 33 - 38 39 44 49

ECLIPSEPARTU-DY-UV

3.4 DMX MODE

• Press the button MENU so many times until the display shows DMX ADDRESS, and press the button ENTER

to conrm.

• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the ECLIPSEPARTU-DY-UV with a light controller, adjust the DMX start address for the

rst a DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst

DMX channel, adjust the start address 33 on the ECLIPSEPARTU-DY-UV. The other functions of the light

eect panel are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

3.5 DMX CONFIGURATION

ECLIPSEPARTU-DY-UV is equipped with dierent DMX conguration.

• Press the button MENU so many times until shows DMX CHANNEL, and press the button ENTER to conrm.

• Select the desired DMX conguration ( 1CH - 2CH - 3CH - 6CH ) through the buttons UP/DOWN.

3.6 SETTINGS

You can change the parameters for the device by following these steps:

SCREEN

You can change the following parameters related to the display, following the same procedure:

• Press the MENU button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight

after a specied time that you can set using the arrow buttons. To have the display always on select

On or choose another value to turn o the display after the amount of time you choose.

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select YES to activate or NO to dis-

able this function.

- Key Lock - With this function, you can lock the buttons on the control panel. If this functionis activat-

ed, the keys are automatically locked. To disable or temporarily disable the key lock function, press

the buttons in the following order to regain access to menu commands: UP, DOWN, UP, DOWN,

ENTER. Select ON to activate or OFF to disable

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

3 CHANNELS

MODE

FUNCTION DMX

Value

3 Ch

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

6 CHANNELS

MODE

FUNCTION DMX

Value

6 Ch

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

AUTO PROGRAMS

No Function

Auto Program 1

Auto Program 2

Auto Program 3

000 - 010

011 - 085

086 - 170

171 - 255

AUTO SPEED

Auto speed slow to fast 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

2 CHANNELS

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

ECLIPSEPARTU-DY-UV

3.7 CHANNELS DMX

ECLIPSEPARTU-DY-UV

3. 8 FIXTURE SETTINGS

It is possible to change the parameter value in the following way:

DIMMER

• Enter in Dimmer mode to select specic dimming curve, press the button MENU so many times until

shows DIM MODE, and press the button ENTER to conrm.

• Press the button UP/DOWN to select OFF - DIM1 - DIM2 - DIM3.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

LED FREQUENCY

• To adjust the frequency of the LEDs, press the MENU button repeatedly until the display shows LED

Frequency, and then press the ENTER button.

• Select the frequency (600Hz - 1200Hz - 2000Hz - 4000Hz - 6000Hz - 25kHz) using the UP/DOWN buttons.

• To conrm, press the ENTER key.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

FAN MODE

• Select this function to set the fans operation mode. Use the arrow buttons to select Auto, On, O, Silent.

Press the ENTER button to conrm your choice

FACTORY RELOAD

Select this function to reset the unit to the factory settings:

- To activate Reset Factory display press the button MENU so many times until shows Factory Reload, and

press the button ENTER to conrm.

• Press ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3. 9 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER but-

ton to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Hours - Through the Fixture Time function you can display the operating time of the projector.

- Software Version - Through Version function you can display the currently installed software version.

- UID - This option shows the RDM identication number

• Press the MENU button repeatedly to exit the menu.

3. 10 OPERATIONS IN AUTOMATIC MODE

MASTER SLAVE

Press the UP/DOWN button to scroll through the menu, select Master/Slave and press ENTER to conrm your

choice.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Slave, if the unit is not connected to other units.

• Press the ENTER button to conrm your choice.

ECLIPSEPARTU-DY-UV

EFFECTS

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the MENU button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Eects icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to select the mode of operation: Eects 1, Eects 2, Eects 3

• Press the ENTER button to conrm your choice.

• Press the MENU button repeatedly to exit the menu and save changes.

The unit will go into automatic mode by executing the program automatically.

ECLIPSEPARTU-DY-UV

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• Faulty LED

• Check the power supply voltage

• Increase the value of the dimmer channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Check for power on power outlet

• Check power cord

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

ECLIPSEPARTU-DY-UV

• ECLIPSEPARTU-DY-UV

• Manuale utente

• Cavo di alimentazione

• Ottiche aggiuntive: 24° (inclusa - per versioni TU e DY),

lenti 12° e 65° incluse (per versioni TU e DY); lente 40° op-

tional (per versioni TU e DY) - telaio porta gelatina inclu-

so (per versioni TU e DY), optional egg crate

• Altro: per la versione UV è inclusa solo l'ottica a 40°.

Nessuna altra ottica o accessorio è disponibile e non deve

essere montata per questa versione

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generali

Attenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 Descrizione e speciche tecniche

1. 2 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento

3. 2 Impostazione base

3. 3 Struttura menù

3. 4 Modalità DMX

3. 5 Congurazione canali

3. 6 Impostazioni del proiettore

3. 7 Canali DMX

3. 8 Funzioni del dispositivo

Frequenza led

Factory Reload

3. 9 Informazioni sul dispositivo

3. 10 Modalità Automatica

Master/Slave

Eects

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Risoluzione dei problemi

ECLIPSEPARTU-DY-UV

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qualsi-

asi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel paese

di utilizzo.

• La distanza minima tra il proiettore e le pareti circostanti deve essere superiore a 50 cm e non devono

• essere ostruite, in nessun caso, le aperture di aerazione.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• La temperatura massima raggiungibile sulla supercie esterna dell’unità, in condizioni di regime termi-

co, è elevata. Dopo lo spegnimento, attendere 15 minuti per il rareddamento.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

• Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in questa docu-

mentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare la funzionalità

del prodotto e/o rappresentare fonte di pericolo.

• Si declina qualsiasi responsabilità derivata dall’uso improprio del prodotto.

ECLIPSEPARTU-DY-UV

- 1 - INTRODUZIONE

1.1 ECLIPSEPARTU-DY-UV - DESCRIZIONE E SPECIFICHE TECNICHE

ECLIPSEPAR is a range of multipurpose LED xtures with a single source, delivering silent operation, high

quality of light and optical exibility, designed to redene the standard for theatrical, TVs and corporate

applications.

ECLIPSEPARTU and DY features a 177W white LED source (3200K TU; 6000K DY) delivering a tremendous

lumen output and superior light quality with CRI and R9 > of 95.

ECLIPSEPARUV is a real UV LED luminaire with a 365nm wavelength LED source.

The xture oers an extensive accessory range including barn doors, lter frame, egg crate and a multitu-

de of interchangeable lenses.

ECLIPSEPAR features a smooth 16bit dimming as well as RDM control and adjustable PWM to look good

in front of a camera.

SORGENTE LUMINOSA

• Sorgente: 177 W white LED / 108W UV LED

• CT: (TU) 3200K - (DY) 6000K

• CRI: > 96 for TU and DY versions

• R9: > 95 for TU and DY versions

• Flusso luminoso: (TU) 12°: 13526 lm - 24°: 13638 lm - 65°: 12376 lm; (DY) 12°: 13571 lm - 24°: 13453 lm

- 65°: 12247 lm; (UV) 229.07lm

• Lux: (TU) 12°: 15200 lux - 24°: 6560 lux - 65°: 1220 lux; (DY) 12°: 16500 lux - 24°: 6860 lux - 65°: 1230 lux;

(UV) 15.9lux @3m

• Lux: (TU) 12°: 5472 lux - 24°: 2361.6 lux - 65°: 439.2 lux; (DY) 12°: 5940 lux - 24°: 2469.9 lux - 65°: 442.8

lux; (UV) 5.724lux @5m

• Durata media sorgente: >70.000 h

• Altro: >85 TLCI, 90/99 TM30 for TU and DY; 365nm for UV LED

OTTICA

• Angolo di proiezione: 10° / 23° / 69° with dierent lens included°

• Angolo di campo: 27° / 40° / 97° with dierent lens included°

• Diametro: (24°) 162.5 - (65°) 163mm

• Tipo lente: lente fresnel

• Ottiche aggiuntive: 24° (on board - for TU and DY versions), 12° and 65° lens included (for TU and DY

versions); 40° lens optional (for TU and DY versions) - gel frame holder included (for TU and DY ver-

sions), egg crate optional

• Altro: 40° lens only included on board in UV version; no other lens or accessories availables for UV

version

EFFETTI DINAMICI

• Modalità colore statico: riproduzione statica di un colore

• Modalità colore manuale: regolazione manuale dimmer e strobo

• Auto mode: programmi integrati con regolazione della velocità di esecuzione

CORPO

• Corpo: alluminio pressofuso

• Colore: nero

ECLIPSEPARTU-DY-UV

CONTROLLO

• Protocolli: DMX512, RDM

• Canali DMX: 1 / 2 / 3 / 6channel

• RDM: RDM ready per controllo e impostazioni remote della xture

• Display: display OLED

• Aggiornamento rmware: si, con interfaccia USB-DMX (UPBOX1) non inclusa

• Master/Slave: per il controllo di più unità collegate in catena

ELETTRONICA

• Dimmer: 0~100% lineare, elettronico

• Curve dimmer: curve dimmer regolabili

• Strobo / shutter: 0 - 30 Hz, elettronico

• Temperatura d’esercizio: -10° ~ +45°

• Flicker: funzionamento senza sfarfallio

• PWM selezionabile: 600~25K Hz

ALIMENTAZIONE

• Potenza assorbita: (TU, DY) 207 W - (UV) 107 W

• Alimentazione elettrica: 100-240V – 50/60Hz

• Potenza assorbita (a 230V): (TU, DY) 207 W - (UV) 127W

• Potenza assorbita (a 120V): (TU, DY) 211 W - (UV) 134W

• Output (a 230V): (TU, DY) 12 - (UV) 16 pcs unità connesse in serie

• Output (a 120V): (TU, DY) 6 - (UV) 8 unità connesse in serie

• Fattore di potenza: pF 0.99 @ 120V - pF 0.94 @ 230V

CARATTERISTICHE FISICHE

• Rareddamento: aria ltrata forzata con ventole silenziate

• Sospensione e ssaggio: qualsiasi posizione con supporti omega (inclusi) “quicklock”

• Connessione di segnale: Amphenol XLR 3p + 5p IN/OUT connectors

• Connessione di alimentazione: Neutrik powerCON IN/OUT connectors

• Grado IP: 20

• Dimensioni (LxAxP): 316x318x404mm

• Peso: 5.5kg

Fig.1 - Technical drawing

ECLIPSEPARTU-DY-UV

316mm/12,44in 318mm/12,52in

404mm/15,91in

La pagina sta caricando ...

ProLights Single source multipurpose LED PAR available in TU, DY and UV version Manuale utente

Marca: ProLights

Modello: Single source multipurpose LED PAR available in TU, DY and UV version

Categoria: Proiettori

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights Single source multipurpose LED PAR available in TU, DY and UV version User manual

ProLights Single source multipurpose LED PAR available in TU, DY and UV version Manuale utente

ProLights Single source multipurpose LED PAR available in TU, DY and UV version Manuale utente

in altre lingue

Documenti correlati