Shindaiwa T2510X_C2510 Manuale utente

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

T2510X

C2510

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RE-GLES DE

SECURITE. LE NON-RESPECT DES REGLES DE SECU-RITE ENTRAINE UN

RISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE-

FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LA-VORARE

IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCA-TA OSSERVANZA

DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

2

1Cover

ENGLISH

(Original instructions)

OPERATOR'S MANUAL

GRASS-TRIMMER/BRUSHCUTTER

T2510X

C2510

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Important information

2Important information

Please ensure that you read the operator's manual before using your product.



Intended use of this product

 Shindaiwa Grass Trimmers/Brushcutters are lightweight, high-performance, petrol engined units designed for weed

control, grass trimming and brush cutting in areas difficult to control by any other means.

 Do not use this unit for any purpose other than aforementioned.



Users of the product

 You should not use this product until you have read the operator's manual carefully and fully absorbed its content.

 This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a

cold, tiredness or otherwise in poor physical condition, or children.

 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.



About your operator's manual

 This manual contains necessary information about the assembly, operation, and maintenance of your product. Please

read it carefully and absorb its contents.

 Always keep your manual in a place where it is readily accessible.

 If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your shindaiwa

dealer.

 The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,

and there may be a slight conversion error in some cases.



Loaning or assigning your product

 When loaning the product described in this manual to another party, ensure that the person borrowing and working with

the product receives the operator's manual along with the product. If you assign your product to another party, please

enclose the operator's manual with the product when handing it over.



Enquiries

 Please contact your shindaiwa dealer for requests regarding information about your product, the purchase of consum-

ables, repairs, and other such enquiries.



Notices

 The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

 This product requires the assembly of some parts.

 Please consult your shindaiwa dealer if anything is unclear or of concern.

Manufacturer:

YAMABIKO CORPORATION

7-2 SUEHIROCHO 1-CHOME, OHME, TOKYO 198-8760, JAPAN

Authorized Representative in Europe:

Atlantic Bridge Limited

Atlantic House, PO Box 4800, Earley, Reading RG5 4GB, United Kingdom

3

Contents

For safe use of your product...............................................................................................4

Warning notices.............................................................................................................4

Other indicators .............................................................................................................4

Symbols.........................................................................................................................4

Location in which a safety decal is attached..................................................................6

Handling fuel..................................................................................................................6

Handling the engine.......................................................................................................7

Handling the product .....................................................................................................8

Packing list........................................................................................................................13

Description........................................................................................................................14

Before you start ................................................................................................................15

Assembly.....................................................................................................................15

Adjusting the balance ..................................................................................................19

Preparing the fuel ........................................................................................................20

Engine operation...............................................................................................................21

Starting the engine ......................................................................................................21

Stopping the engine.....................................................................................................23

Trimming operation...........................................................................................................24

Basic trimming operation with nylon line cutting head.................................................24

Basic trimming operation with metal blade..................................................................26

Precautions to observe when working.........................................................................27

Maintenance .....................................................................................................................29

Daily Maintenance.......................................................................................................29

10- Hour Maintenance.................................................................................................29

10/15 Hour Maintenance .............................................................................................29

50-Hour Maintenance..................................................................................................30

139-Hour or Annual Maintenance................................................................................30

Carburettor adjustment................................................................................................31

Checking the blade......................................................................................................32

Long term storage .......................................................................................................32

Troubleshooting Guide ................................................................................................33

Specifications....................................................................................................................36

Declaration of conformity..................................................................................................37

4

For safe use of your product

Be careful to read this section before using your product.



The precautions described in this section contain important safety information. Please observe them carefully.



You must also read the precautions that appear in the body of the manual itself.

Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.

Warning notices

Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product

itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.

Other indicators

As well as warning notices, this manual uses the following explanatory symbols:

Symbols

In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what

each symbol means.

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual

The maximum speed of the

cutting attachment shaft in

r/min

Wear eyes, ears and head

protection

Keep bystanders away 15 m

Wear foot protection and

gloves

Petrol and oil mixture

Emergency stop Purge bulb (Primer)

Warning!

Thrown objects!

Carburettor adjustment

- Low speed mixture

5

For safe use of your product

Warning, side thrust

Carburettor adjustment

- High speed mixture

Usage without shield not per-

mitted

Carburettor adjustment

- Idle speed

Usage of metal blades not

permitted

U-handle

Usage of nylon line cutting

head not permitted

Loop handle

Do not use the product in plac-

es with poor ventilation

Beware of high-temperature

areas

Beware of fire

Guaranteed sound power lev-

el

Choke Control "Cold Start"

Position (Choke Closed)

Choke Control "Run" Position

(Choke Open)

Beware of electric shocks Engine start

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

6

For safe use of your product

Location in which a safety decal is attached

 The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

 If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

Handling fuel

1. Safety decal (Part number X505-003130)

DANGER

Always keep well away from fire when refuelling

 If you do so, the fuel could ignite and cause fire, leading to burns.

Fuel is highly inflammable and leads to a risk of fire if mishandled. Use extreme care when mixing, stor-

ing or handling or serious personal injury may result. Be careful to observe the following instructions.



Do not smoke or hold a flame near when refuelling.



Do not fuel up while the engine is hot or in operation.

About the container and refuelling place



Use an approved fuel container.



Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.



DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.

Fuel spills can cause fire

Observe the following precautions when refuelling:



Do not add so much fuel that it reaches the mouth of the fuel tank. Keep

the fuel within the prescribed level (up to the shoulder level of the fuel

tank).



Mop up any fuel that overflows or spills out due to overfilling.



Tighten the fuel tank cap securely after refuelling.

 Fuel spills can cause fire and burns when ignited.

7

For safe use of your product

Handling the engine

Do not start the engine in the area where you refueled



You must not start the engine in the place where you carried out the refuelling. Move at least

3m from the place where you refueled before starting the engine.

 Fuel leaks that occur while refuelling can cause fire if ignited.

Fuel leaks cause fire



After refuelling, always check that there are no leaks or discharges of fuel from the fuel pipe, fuel

system grommets, or around the fuel tank cap.



If you do find fuel leaks or discharges, stop using the product immediately and contact your dealer

to have it repaired.

 Any fuel leaks could cause fire.

DANGER

WARNING

Starting the engine

Be particularly careful to observe the following precautions when starting the engine:



Check that none of the nuts and bolts are loose



Check that there are no fuel leaks



Place the product in a flat, well ventilated place



Leave plenty of space around the product and do not allow people or animals near it



Start the engine with the throttle trigger in the idle speed position



Hold the product firmly to the ground when starting the engine

 Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

Once the engine has started, check for abnormal vibrations and sounds



Check that there are no abnormal vibrations or sounds once the engine starts. Do not use the product if there are

abnormal vibrations or sounds. Contact your dealer to have it repaired.

 Accidents involving parts that fall or shatter off can cause wounds or serious injury.

Do not touch high temperature or high voltage components while the product is running

Do not touch the following high temperature or high voltage components while the product is running or

for some time after it stops.



Silencer, spark plug, angle transmission, and other high temperature components

 You could burn yourself if you touch a high temperature component.



Spark plug, spark plug wire, and other high voltage components

 You could receive an electric shock if you touch a high voltage component while the product is running.

Put safety first in the case of fire or smoke



If fire comes from the engine or smoke appears from any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safety.



Use a shovel to throw sand or other such material on the fire to prevent it from spreading, or put it out

with a fire extinguisher.

 A panicked reaction could result in the fire and other damage becoming more extensive.

Exhaust fumes are toxic



The exhaust fumes from the engine contain toxic gases. Do not operate the product indoors or in other

ill ventilated places.

 The exhaust fumes could cause poisoning.

Turn off the engine when checking or maintaining the product

Observe the following precautions when checking and maintaining your product after use:



Turn the engine off and do not attempt to check or maintain the product until the engine has cooled

 You could burn yourself.



Remove the spark plug cap before performing checks and maintenance

 An accident could occur if the product starts unexpectedly.

8

For safe use of your product

Handling the product

General precautions

Precautions for use

Checking the spark plug

Observe the following precautions when checking the spark plug.



If the electrodesor terminals are worn, or if there are cracks in the ceramics, replace

them with new parts.



The spark test (for checking whether the spark plug is sparking) must be carried out

by your dealer.



The spark test must not be carried out in proximity of the spark plug hole.



The spark test must not be performed in places where there are fuel spills or inflammable gases



You must not touch the metal parts of the spark plug

 The spark plug could ignite a fire or give you an electric shock.

WARNING

Operator's manual



Be careful to read the operator's manual properly before using your product in order to ensure correct

operation.

 Failure to do so could lead to an accident or serious injury.

Do not use the product for anything other than its intended purpose



You must not use the product for any purpose other than those described in the operator's manual.

 To do so could lead to an accident or serious injury.

Do not modify the product



You must not modify the product.

 To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be

covered by the manufacturer's warranty.

Do not use the product unless it has been checked and maintained



You must not use the product unless it has been checked and maintained. Always ensure that the product is checked

and maintained on a regular basis.

 Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product



When loaning your product to another party, ensure that the person borrowing the product receives the operator's

manual along with it.



If you assign your product to another party, please enclose the operator's manual with the product when handing it

over.

 Failure to do so could lead to an accident or serious injury.

Being prepared in case of an injury

In the unlikely event of an accident or injury, please ensure that you are pre-

pared.



First aid kit



Towels and wipes (to stop any bleeding)



Whistle or mobile phone (for calling outside help)

 If you are unable to perform first aid or call for outside help, the injury could

worsen.

DANGER

Do not use the product when the trimmer blade is turning at idle speed



You must not use the product while the trimmer blade is turning if the Grass Trimmer is running with the throttle

trigger in the idle speed position.

 To do so could lead to an accident or serious injury.

9

For safe use of your product

Do not remove the shield



Do not operate the product without the shield in place.

 Any objects that ricochet off the trimmer blade could cause an accident or serious injury.

The area within a 15 m radius is a danger zone

The area within a 15 m radius of the product is a danger zone. Be careful to ob-

serve the following precautions while working with the product.



Do not allow children and other people or pets to enter the danger zone.



If another person enters the danger zone, turn off the engine to stop the blade

from rotating



When approaching the operator, signal to him by, for example, throwing twigs

from outside the danger zone, and then check that engine has been switched

off and the blade has stopped turning



If more than one person is working with the product, identify the way in which

you will signal to each other and work at least 15 m apart

 Any objects that ricochet off the trimmer blade, and any contact with the trimmer blade, could cause blindness or a fatal ac-

cident.

DANGER

WARNING

Users of the product

The product should not be used by:



people who are tired



people who have taken alcohol



people who are on medication



people who are pregnant



people who are in poor physical condition



people who have not read the operator's manual



children

 Failure to observe these instructions could lead to an accident.

Environment of use and operation



Do not use the product in places where there is no sure foothold, such as on steep slopes or after rainfall, as such

places are slippery and dangerous.



Do not operate the product at night or in dark places with poor visibility.



When using the product on a gentle slope, work in a level, contour-like motion.

 A serious injury could result if you fall or slip, or fail to operate the product correctly.



For your own health and your safe and comfortable work, operate the machine within the air temperature range of -

5

o

C to 40

o

C.

 Failure to observe these instructions could result in damage to your health.

Turn off the engine when moving around

When moving around in the situations described below, turn off the engine and ensure that the trimmer blade has

stopped rotating, then fit the trimmer blade cover and position the silencer away from yourself.



Moving to the place where you are working



Moving to another area while you are working



Leaving the place where you have been working

 Failure to observe these precautions could cause burns or serious injury.



When transporting the product by car, empty the fuel tank, fit the trimmer blade cover, and secure the product firmly

in place to prevent it from moving around.

 Travelling by car with fuel in the trimmer tank could lead to a fire.

10

For safe use of your product

Vibration and cold

It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning, fol-

lowed by loss of colour and numbness in the fingers. The following precautions are strongly recommended because

the minimum exposure which might trigger the ailment is unknown.



Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.



Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not

smoking.



Limit the number of hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-held

power equipment is not required.



If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, consult

your physician before exposing yourself further to cold and vibration.

 Failure to observe these instructions could result in damage to your health.

Repetitive stress injuries

It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness,

swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities may put

you at a high risk for developing a repetitive stress injury (RSI). To reduce the risk of RSI, do the following:



Avoid using your wrist in a bent, extended or twisted position.



Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the

repetitive movement.



Do exercises to strengthen hand and arm muscles.



See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-

nosed, the more likely permanent nerve and muscle damage can be prevented.

 Failure to observe these instructions could result in damage to your health.

WARNING

Proper training

Do not permit operation without proper training and protective equipment.

Be thoroughly familiar with the controls and proper use of unit.

Know how to stop the unit and shut off the engine.

Know how to unhook a harnessed unit quickly.

Never allow anyone to use the unit without proper instruction.

WARNING

Remove foreign objects and obstructions before working with the product



Before starting work, check the area where you will be working and remove any small

stones and empty cans likely to ricochet off the cutting attachment, as well as any

pieces of string or wire that might become twisted around the cutting attachment.

 An accident or serious injury can occur if foreign objects ricochet off the cutting attachment

or wire and other materials twisted round the product spring off it.

Do not hold the cutting attachment up when working with the product



Do not hold the cutting attachment up while you work. You must not work with the cutting attachments raised above

knee level.

 Raising the cutting attachment above knee level brings the plane of rotation closer to the face, and any objects that fly off the

cutting attachments could cause an accident or serious injury.

Turn off the engine immediately if anything goes wrong

In the following situations, turn off the engine immediately and ensure that the cutting attachments have stopped before

checking each area of the product. Replace any damaged parts.



If the cutting attachment hits a rock, tree, post, or other such obstruction while you work.



If the product suddenly starts to vibrate abnormally.

 Continuing to use parts when they are damaged could lead to an accident or serious injury.

11

For safe use of your product

Precautions concerning the cutting attachment

1.With metal blade

2.With nylon line cutting head

Kickback



The phenomenon that occurs if the trimmer blade comes into con-

tact with a tree, post, rock or other hard object while rotating at

high speed and reacts by recoiling powerfully and instantaneously

is known as kickback.



Causing kickback can result in a loss of control over the product

and is highly dangerous.



In particular, if the front-right quadrant of the trimmer blade (B)

strikes a shrub or other such object, the trimmer blade will cause

the product to recoil sharply backwards to the right.



To prevent kickback, do not trim from left to right. Be careful to en-

sure that the trimmer blade does not strike any hard objects.



When trimming, ensure that the object you are cutting meets the

portion of the blade 1/3 in from the front edge on the left-hand side

(A).

 Failure to do so could cause an injury or fatal accident.

WARNING

DANGER

Always stop the engine when a cutting attachment jam occurs. Do not attempt to remove an object causing a jam if the

engine is running. Severe injury can occur if a jam is removed and the cutting attachment suddenly starts.

WARNING

Use correct blades



Serious injury may result from the improper use of blades. Read and comply with all safety instructions listed in this

manual.



The 3 cutter blade is designed especially to cut weeds and grass. To avoid injury due to kickback or blade fracture,

do not use the 3 cutter blade to cut brush or trees.



Use only cutting attachments recommended by YAMABIKO CORPORATION.

 Damaged or shattered blades can cause accidents and serious injury.

Inspect blade before use

Pieces from a cracked metal blade can fly off during operation. Inspect metal blades for cracks before each use. Discard

cracked blades no matter how small the crack. Cracked blades can be the result of the misuse or improper sharpening.

 Damaged or shattered blades can cause accidents and serious injury.

Reaction forces

Be sure you understand the reaction forces of push and pull, and kickback described in this manual, and how these

forces may affect your balance in the operation of a unit.

 Failure to do so could cause an injury or fatal accident.

WARNING

Use correct cutting attachment



Serious injury may result from the improper use of cutting attachment. Read and comply with all safety instructions

listed in this manual.



Use only cutting attachments recommended by YAMABIKO CORPORATION.



Use only nylon line cutting head. Do not use any type of metal blade.

 Failure to do so could lead to an accident or serious injury.



Excessive nylon line beyond cut off knife could fly off when the nylon line cutting head starts rotating after adjust-

ment of nylon line length.

 Failure to do so could lead to an accident or injury.

12

For safe use of your product

Protective gear

Do not trim near cars or pedestrians

Use extreme caution when operating over bare spots and gravel, because the line can throw small rock particles at high

speeds. The shield on the unit cannot stop objects which bounce or ricochet off hard surfaces.

 Failure to do so could lead to an accident or serious injury.

Avoid wire

Do not trim in any area where there are broken strands of fencing wire. Remove the broken pieces of wire, or give the

area wide berth. Wear proper safety protection. Do not cut where you cannot see what the cutting device is cutting.

 Failure to do so could lead to an accident or serious injury.

WARNING

CAUTION

Use only flexible, non-metallic line recommended by YAMABIKO CORPORATION.

WARNING

Wear protective gear

Always wear the following protective gear when working with the trimmer.

1. Head protection (helmet): Protects the head

2. Ear muffs or ear plugs: Protect the hearing

3. Safety goggles: Protect the eyes

4. Face shield: Protects the face

5. Safety gloves: Protect the hands from cold and vibration

6. Work clothes that fit (long sleeves, long trousers): Protect the body

7. Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes

(with toecaps): Protect the feet

8. Shin guards: Protect the legs

 Failure to observe these precautions could result in damage to your sight or hearing, or

lead to a serious injury.

When necessary, please use the protective gear below.

 Dust mask: Protects the breathing apparatus

 Bee net: To deal with attacks by bees

Wear proper clothing.

Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the unit.

Do not wear open toed footwear, or go bare-foot or barelegged. In certain situations, total

face and head protection may be required. For heavy brush cutting with metal blade, log-

ger's trousers or leg chaps with protective inserts are added considerations.

 Failure to observe these precautions could result in damage to your sight or hearing, or lead

to a serious injury.

13

Packing list

 The following parts are packed separately in the packing box.

 When you have unpacked the box, please check the parts that it contains.

 Contact your dealer if anything is missing or broken.

1. Engine and shaft tube

2. Shield

3. Sub-shield

4. Handle

5. Shoulder harness

6. Blade cover

7. Tool set

 L-wrench

 Spanner

 Socket wrench

 Upper clamp

 Spacer

8. Safety goggles

9. Operator's manual

1. Engine and shaft tube

2. Shield

3. Sub-shield

4. Handle

5. Shoulder harness

6. Blade cover

7. Tool set

 L-wrench

 Spanner

 Socket wrench

 Upper clamp

 Spacer

 Band

8. Safety goggles

9. Operator's manual

14

Description

1. Angle transmission Having two gears to change to

angle of rotating axis.

2. Cutting attachment

3. Shield Device to protect the operator from accidental

contact with the cutting head and thrown objects.

4. Shaft tube Part of the unit that provides a casing for

power transmission shaft.

5. Loop-handle Light weight, suitable for nylon line trim-

mer.

6. U-handle Having the configuration of a bicycle handle

bar to reduce working effort compared to a loop-handle.

7. Suspension point Device on which the harness can

be hooked.

8. Shoulder harness An adjustable strap to suspend unit.

9. Throttle trigger Activated by the operator's finger for

controlling the engine speed.

10. Ignition switch

11. Throttle trigger lockout Locks throttle trigger in the

idling position until you have a proper grip with your right

hand around the handle.

12. Air cleaner cover Covers air filter.

13. Fuel tank cap For closing the fuel tank.

14. Fuel tank Contains fuel and fuel filter.

15

Before you start

Before yo u start

Assembly

Assembly of the handle

Loop handle version

1. Put the 4 square nuts into the frame of barrier.

2. Fit the handle and barrier over the outer pipe and tighten the

4 bolts.

3. Position the handle about 250 mm ahead of the throttle

housing end.

4. Secure the handle by alternately tightening the four bolts in

a diagonal or "crisscross" fashion.

U-handle

1. Use the 4 mm L-wrench to remove the lower cap retaining

screws from the handlebar bracket.

2. Position the handle on the outer tube forward of Handle po-

sitioning label as shown in figure. Reassemble the lower cap

to the handlebar bracket in the reverse order of disassembly.

3. Locate the handle in the best position for operator comfort.

4. Firmly tighten both lower cap retaining screws.

5. Secure the cable to the outer pipe with the 2 bands as the

illustration shows. The 2 bands are in the tool bag.

Adjust throttle lever free play

The throttle lever free play should be approximately 4-6 mm.

Make sure that the throttle lever operates smoothly without bind-

ing. If it becomes necessary to adjust the lever free play, follow

the procedures and illustrations that follow.

WARNING

Read the operator's manual carefully to ensure that you assemble the product correctly.

 Using a product that has been incorrectly assembled could lead to an accident or serious injury.

CAUTION



Install the handle so that it does not hide any of the safety decals.

1. Square nut

2. Barrier

3. Handle

4. About 250 mm

5. Bolt

1. Lower cap retaining

screw

2. Lower cap

3. Handle positioning la-

bel

4. Band

5. Handlebar

6. Engine

16

Before you start

1. Remove the air cleaner cover by loosening the two thumb-

screws.

2. Loosen the lock nut on the cable adjuster.

3. Turn the cable adjuster in or out as required to obtain proper

free play 4-6 mm.

4. Tighten the locknut.

5. Reinstall the air cleaner cover.

Cutting attachment shield assembly

Cutting Attachment Shield

1. Insert the cutting attachment shield between the outer tube

and the cutting attachment shield mounting plate.

2. Fit the two shims and the bracket over the outer tube and

loosely install the four socket-head cap screws.

3. Tighten the four socket-head cap screws to secure the cut-

ting attachment shield.

Sub-shield (when trimmer head is in use) (Consult

your dealer.)

1. Attach the shield extension to the cutting attachment shield.

1. Cable adjuster 2. Lock nut

1. Socket-head cap

Screw

2. Bracket

3. Shim

4. Clamp screw

5. Outer tube

6. Cutting attachment

shield

7. Shim

8. Cutting attachment

shield mounting plate

9. Retaining nut

NOTE

It may be necessary to loosen the retaining nut and clamp

screw to adjust cutting attachment shield mounting plate.

CAUTION

Make sure the clamp screw and retaining nut are securely

tightened before tightening the four socket-head cap

screws.

1. Cutting attachment

shield

2. Hook receiver

3. Sub-shield

4. Hook

WARNING

Never use this product without sub-shield when using a

trimmer head.

CAUTION

Make sure the sub-shield is completely hooked at the

hook receiver.

17

Before you start

Installing a trimmer head

1. With the gearcase output shaft facing up, rotate the output

shaft and Holder A until the hole in Holder A aligns with the

matching hole in the gearcase flange, and then lock the hold-

er to the gearcase by inserting the long end of the L- wrench

through both holes.

2. Using the socket wrench, remove the shaft bolt, bolt guard,

Holder B and the safety clip. (The bolt guard, shaft bolt and

safety clip are not used with a trimmer head).

3. Install Holder B on the gearcase shaft. The splined hole on

Holder B must engage with the gearcase shaft.

4. Using the L-wrench to secure Holder A, install and hand-

tighten the trimmer head (counter-clockwise to install).

5. Remove the L-wrench from the gearcase and holder.

Installing a blade

1. Shaft bolt (not used)

2. Bolt guard (not used)

3. Holder B

4. Safety clip (not used)

5. Holder A

6. Gearcase shaft

NOTE

This product is shipped with Holder A, the blade retainer (safe-

ty clip), Holder B, shaft bolt, and bolt guard installed. The shaft

bolt is a LEFT-HAND thread. Remove it by turning CLOCK-

WISE!.

1. L-wrench

WARNING



Do not attempt to fit the trimmer blade with one hand or without using the socket spanner. Fit the trimmer blade ac-

curately using the supplied socket spanner and tighten firmly in position.



The trimmer must not be used if the blade vibrates or is loose.



Wear heavy duty gloves when working with the trimmer blade. When replacing the trimmer blade during a trimming

task, ensure that the engine is switched off and that the blades have stopped.



Do not use any tools other than the proved socket spanner to tighten the blade, a pneumatic or electric tool may

tighten the blade more than necessary and cause the nut or the output shaft to break.



When turning the product over to replace the trimmer blade, ensure that the fuel tank cap is securely in place.

 Failure to do so could lead to an injury or serious accident, or cause a fire.

18

Before you start

1. Turn the product upside down so the gearcase output shaft

is facing UP and remove the shaft bolt, bolt guard and holder

B from the gearcase shaft.

2. Align the hole in blade holder A with the matching hole in the

gearcase flange and then temporarily lock the output shaft

by inserting a L-wrench through both holes.

3. Slide the safety clip off-center.

4. Fit the blade over the safety clip and then center it over the

flange on holder A.

1. Shaft bolt

2. Bolt guard

3. Holder B

4. Output shaft

5. Safety clip

6. Holder A

7. L-wrench

1. Safety clip

1. Blade

CAUTION

Install the blade so its printed surface is visible to the

operator when the brushcutter is in the normal operat-

ing position.

WARNING

The blade must fit flat against the holder flange. The

blade mounting hole must be centered over the raised

boss on blade holder A.

NOTE

When installing certain blades, it may be necessary to tempo-

rarily remove the safety clip.

La pagina sta caricando ...

Shindaiwa T2510X_C2510 Manuale utente

Shindaiwa T2510X_C2510 Manuale utente

in altre lingue

Documenti correlati

Altri documenti