Gigabyte GA-K8VT800 Manuale del proprietario

GA-K8VT800(Pro)

User's Manual

AMD Socket 754 Processor Motherboard

Rev. 1005

12ME-K8VT800P-1005

Copyright

Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any from

without the expressed, written permission of GBT.

Trademarks

Third-party brands and names are the property of their respective owners.

Notice

Please do not remove any labels on motherboard, this may void the warranty of this motherboard.

Due to rapid change in technology, some of the specifications might be out of date before publication of this booklet.

The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a

commitment to update the information ontained herein.

Mother Board

GA-K8VT800 / GA-K8VT800 Pro

September 2, 2003

Motherboard

GA-K8VT800 / GA-K8VT800 Pro

September 2 ,2003

- 4 -GA-K8VT800(Pro) Motherboard

English

When you installing AGP card, please make sure the following notice is fully understood and

practiced. If your AGP card has "AGP 4X/8X(1.5V) notch" (show below), please make sure your

AGP card is AGP 4X/8X(1.5V).

AGP 2X(3.3V) card is not supported by VIA K8T800 chipset. You might experience system unable

to boot up normally. Please insert an AGP 4X/8X(1.5V) card.

Read Me First !

AGP 4X/8X notch

5 Read Me First

English

Installing the motherboard to the chassis…

If the motherboard has mounting holes, but they don't line up with the holes on the base and there

are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the

mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off,

so be careful of your hands). In this way you can still attach the motherboard to the base without

worrying about short circuits. Sometimes you may need to use the plastic springs to isolate the

screw from the motherboard PCB surface, because the circuit wire may be near by the hole. Be

careful, don't let the screw contact any printed circuit write or parts on the PCB that are near the

fixing hole, otherwise it may damage the board or cause board malfunctioning.

Preparing Your Computer

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever

you work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

The manufacturer assumes no liability for any damage, caused directly or indirectly, by improper

installation of any comfortable performing the installation, consult a qualified computer technician.

Damage to system components, and injury to yourself may result if power is applied during

installation.

- 6 -GA-K8VT800(Pro) Motherboard

English

Table of Content

Read Me First ! ....................................................................................... 4

Chapter 1 Introduction ............................................................................ 8

1-1 Item Check List ............................................................................ 8

1-2 Features Summary ................................................................................ 8

1-3 GA-K8VT800(Pro) Motherboard Layout ............................................. 11

1-4 Block Diagram - GA-K8VT800(Pro).................................................... 12

Chapter 2 Hardware Installation Process ............................................. 15

Step 1: Installing Processor and CPU Cooling Fan.................................. 16

Step 2: Installing Memory Modules ........................................................... 18

Step 3: Installing expansion cards ............................................................ 20

Step 3-1: AGP Card Installation..................................................................................... 20

Step 4: Connect ribbon cables, cabinet wires and power supply ............ 21

Step 4-1: I/O Back Panel Introduction........................................................................... 21

Step 4-2: Connectors Introduction ................................................................................. 23

Chapter 3 BIOS Setup ......................................................................... 39

The Main Menu (For example: BIOS Ver. : F1a) ...................................... 40

Standard CMOS Features......................................................................... 42

Advanced BIOS Features .......................................................................... 45

Integrated Peripherals .............................................................................. 47

Power Management Setup ....................................................................... 52

PnP/PCI Configurations ............................................................................. 55

PC Health Status........................................................................................ 56

Table of Content

English

- 7 -

Frequency/Voltage Control ........................................................................ 58

Load Fail-Safe Defaults ............................................................................. 60

Load Optimized Defaults ........................................................................... 61

Set Supervisor/User Password .................................................................. 62

Save & Exit Setup ....................................................................................... 63

Exit Without Saving ................................................................................... 64

Chapter 4 Technical Reference ........................................................... 67

@BIOS™ Introduction ................................................................................. 67

EasyTune™ 4 Introduction ......................................................................... 68

Flash BIOS Method Introduction ............................................................... 69

2- / 4- / 6-Channel Audio Function Introduction ........................................ 79

Jack-Sensing Introduction......................................................................... 85

UAJ Introduction ........................................................................................ 87

Xpress Recovery Introduction ................................................................... 89

Chapter 5 Appendix ............................................................................. 97

- 8 -GA-K8VT800(Pro) Motherboard

English

1-1 Item Checklist

The GA-K8VT800(Pro) motherboard

CD for motherboard driver & utility

The GA-K8VT800(Pro) user's manual

Quick PC Installation Guide

GigaRAID manual(1)

GC-SATA Card (optional)

(Manual; SATA cable x 1; Power cable x 1)

IDE cable x 3 / Floppy cable x 1(1)

IDE cable x 1 / Floppy cable x 1(2)

Serial ATA cable x 2

USB & IEEE 1394 Cable x 1(1)

USB Cable x 1(2)

SPDIF Out Kit x 1(1)

I/O Shield

Motherboard Settings Label

Chapter 1 Introduction

Form Factor 30.5cm x 23.0cm ATX size form factor, 4 layers PCB

CPU Socket 754 for AMD AlthlonTM 64 processor (K8)

128K L1& 256K / 512K / 1M L2 cache on die

800MHz FSB

Support core frequencies in excess of 1.6 GHz(2800+) and faster

Chipset VIA K8T800 AGP/PCI Controller (PAC)

VIA VT8237 Integrated Peripheral Controller (PSIPC)

Memory 3 184-pin DDR DIMM sockets

Supports DDR400/DDR333/DDR266 DIMM

Supports unbuffered DIMMs with a 64-bit data bus with optional 8

bits of Error Correcting Code (ECC)

Supports 128MB/256MB/512MB/1GB DRAM

Supports up to 3GB DRAM (Max)

I/O Control ITE8705

Slots 1 AGP slot supports 8X/4X mode,

AGP3.0 8X interface at 533MHz

5 PCI slots support 33MHz & PCI 2.3 compliant

1-2 Features Summary

to be continued......

(1) For GA-K8VT800 Pro only (2) For GA-K8VT800 only

Introduction

English

- 9 -

On-Board IDE 2 IDE controllers provides IDE HDD/CD-ROM (IDE1, IDE2) with

PIO, Bus Master (Ultra DMA33/ATA66/ATA100/ATA133) operation

modes

IDE3 and IDE4 compatible with RAID, Ultra ATA133/100, IDE

Hardware Monitor CPU/System fan revolution detect

CPU/System temperature detect

CPU warning temperature

System voltage detect

CPU/System fan fail warning

CPU Smart Fan control (1)

Thermal shutdown function

On-Board Peripherals 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes

1 Parallel port supports Normal/EPP/ECP mode

2 Serial ports (COMA & COMB)

8 USB 2.0/1.1 ports (4 x Front by cable)

3 IEEE1394 ports (by cable) (1)

1 IrDA connector for IR

1 Front Audio connector

On-Board LAN RTL Gigabit LAN (RTL8110S)(1)

RTL 10/100 LAN (RTL8100C)(2)

1 RJ45 ports

On-Board Sound Realtek ALC658 CODEC (UAJ)

Supports Jack Sensing function

Line Out / 2 front speaker

Line In / 2 rear speaker (by s/w switch)

Mic In / center & subwoofer (by s/w switch)

SPDIF In / Out

CD In / AUX In / Game port

On-Board SATA RAID '*' Built-in VT8237

Supports Disk striping (RAID0) or DISK Mirroring (RAID1)

Supports UDMA up to 150 MB/sec.

Up to 2 SATA devices(Note)

to be continued......

(1) For GA-K8VT800 Pro only (2) For GA-K8VT800 only

'*' If you want to find the detailed information for SATA RAID setup installation,

please download the VT8237 SATA Manual from GIGABYTE’s website.

(Note) It is recommended to use SATA (1.5Gb/s) hard disks.

- 10 -GA-K8VT800(Pro) Motherboard

English

On-Board IDE RAID(1)Onboard GigaRAID IT8212F chipset

Supports data striping (RAID 0) or mirroring (RAID 1) or

striping+mirroring (RAID 0 + RAID 1)

Supports JBOD function

Supports concurrent dual ATA133 IDE controller operation

Support ATAPI mode for HDD

Supports IDE bus master operation

Support ATA133/RAID mode switch by BIOS

Displays status and error checking messages during boot-up

Mirroring supports automatic background rebuilds

Features LBA and Extended Interrupt 13 drive translation in

controller onboard BIOS

On-Board IEEE1394 (1)Built-in Ti TSB43AB23

PS/2 Connector PS/2 Keyboard interface and PS/2 Mouse interface

BIOS Licensed AWARD BIOS

Supports Dual BIOS (1)

Supports Face Wizard (1)

Supports Q-Flash

Additional Features PS/2 Keyboard power on by password

PS/2 Mouse power on

External Modem wake up

STR(Suspend-To-RAM)

Wake on LAN (WOL)

AC Recovery

Poly fuse for keyboard over-current protection

USB KB/Mouse wake up from S3

Supports Thermal Shutdown function

Supports Easy Tune4

Supports @BIOS

Overclocking Over Voltage (CPU/DDR/AGP) by BIOS

Over Clock (CPU/DDR/AGP) by BIOS

Please set the CPU host frequency in accordance with your processor's specifications.

We don't recommend you to set the system bus frequency over the CPU's specification because

these specific bus frequencies are not the standard specifications for CPU, chipset and most of the

peripherals. Whether your system can run under these specific bus frequencies properly will

depend on your hardware configurations, including CPU, Chipsets, SDRAM, Cards…etc.

(1) For GA-K8VT800 Pro only

Introduction

English

- 11 -

VIA VT8237

USB

(1) For GA-K8VT800 Pro only (2) For GA-K8VT800 only

CD_IN

GA-K8VT800(Pro)

KB_MS

COMB

LPT

USB

LAN

ATX_12V

SOCKET 754

CPU_FAN

IDE1

IDE2

DDR2

COMA

PWR_LED

BAT

PCI1

PCI2

PCI3

F_USB1

ITE8705

MAIN

BIOS

CODEC

PWR_FAN(1)

VIA K8T800

DDR3

PCI4

PCI5

GAME

F_AUDIO

AUX_IN

IR

IDE3(1)

GigaRAID

IT8212(1)

BACKUP

BIOS(1)

SATA1

RAM_LED

ATX

SYS_FAN

NB_FAN(1)

IDE4(1)

DDR1

SPDIF_IO

SUR_CEN

AUDIO

F_PANEL

1-3 GA-K8VT800(Pro) Motherboard Layout

F2_1394(1)

INFO_LINK

AGP

FDD

SATA0

F1_1394(1)

RTL8100C(2)

RTL8110S(1)

TSB43AB23(1)

F_USB2

CLR_PWD

- 12 -GA-K8VT800(Pro) Motherboard

English

1-4 Block Diagram - GA-K8VT800(Pro)

VIA

K8T800

VIA

VT8237

CPUCLK+/- (200MHz)

AGPCLK66MHz

33 MHz

14.318 MHz

48 MHz

AGP slot

4X/8X

AGPCLK

(66MHz)

5 PCI

PCICLK

(33MHz)

AC97 Link

8 USB

Ports

ATA66/100/133

IDE Channels

CLK

GEN

CPUCLK+/- (200MHz)

AGPCLK (66MHz)

PCICLK (33MHz)

USBCLK (48MHz)

14.318 MHz

33 MHz

IT8705

24 MHz

33 MHz

Game Port

Floppy

LPT Port

COM

Ports

AC97

CODEC

MIC

LINE-IN

LINE-OUT

Dual BIOS(1)

66MHz V_Link

V_Link (66MHz)

2 SATA

Ports

AMD

AlthlonTM 64

processor (K8)

System Bus

800MHz DDR400/333/266 DIMM

DDR RAM

RJ45

RTL8110S(1)

RTL8100C(2)

LAN

TSB43AB23(1)

3 IEEE1394(1)

IDE3

(1)

IDE4

(1)

GigaRAID

IT8212(1)

(1) For GA-K8VT800 Pro only (2) For GA-K8VT800 only

PS/2

KB/Mouse

Introduction

English

- 13 -

- 14 -GA-K8VT800(Pro) Motherboard

English

Hardware Installation Process

English

- 15 -

To set up your computer, you must complete the following steps:

Step 1- Installing Processor and CPU Cooling Fan

Step 2- Installing Memory Modules

Step 3- Installing Expansion Cards

Step 4- Connect ribbon Cables, Cabinet Wires, And Power Supply

Chapter 2 Hardware Installation Process

Step 2

Step 4

Step 3

Step 4

Step 1

Step 4

Congratulations! You have accomplished the hardware installation!

Turn on the power supply or connect the power cable to the power outlet. Continue with the

BIOS/software installation.

- 16 -GA-K8VT800(Pro) Motherboard

English

Step 1: Installing Processor and Heatsink

1.1 The installation of the processor and heatsink is performed in four main steps:

Step 1-1. Processor insertion

Step 1-2. Applying thermal grease

Step 1-3. Heatsink attachment

Step 1-4. Connecting processor fan power

These steps are described in detail in the following paragraphs.

Before installing the processor and heatsink, adhere to the following warning:

1. The processor will overheat without the heatsink and/or fan, resulting in permanent

irreparable damage.

2. Never force the processor into the socket.

3. Apply thermal paste between the processor and heatsink.

4. Please make sure the CPU type is supported by the motherboard.

5. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause improper

installation. Please change the insert orientation. Please use AMD approved cooling

fan.

Step 1-1. First, check the processor pins to see that none are bent. Move the socket lever to the

unlocked position as shown in Figure 1 & Figure 2.(90 to the plane of the motherboard) prior to

inserting the processor. The A1 pin location is designated on the processor by a copper triangle that

matches up to a triangle on the socket as shown in Figure 3. Align the processor to the socket and

gently lower it into place. Do not force the processor into the socket.

Figure 1.Angling the rod

to 65-degree maybe feel

a kind of tight , and then

continue pull the rod to 90-

degree when a noise

“cough” made.

Figure 2.Pull the rod to

the 90-degree directly.

Angling the

rod to 650Socket

Actuation

Lever

Figure 3. A1 pin location on the Socket and

Processor.Move the socket lever to the locked

position while holding pressure on the center of the

processor.

Hardware Installation Process

English

- 17 -

Step1-2. When the processor is installed in the socket, apply thermal grease to the processor(as

shown in Figure 4) prior to installing the heatsink. AMD recommends using a high thermal

conductivity grease (such as Shin-Etsu types G751 or G749, or an equivalent product) for

the thermal interface material rather than a phase change material. Phase change materials

develop strong adhesive forces between the heatsink and processor.

Removing the heatsink under such conditions can cause the processor to be

removed from the socket without moving the socket lever to the unlocked

position and then damage the processor pins or socket contacts.

** We recommend you to apply the thermal tape to provide better heat conduction between your

CPU and heatsink. (The CPU cooling fan might stick to the CPU due to the hardening of the

thermal paste. During this condition if you try to remove the cooling fan, you might pull the

processor out of the CPU socket alone with the cooling fan, and might damage the processor.

To avoid this from happening, we suggest you to either use thermal tape instead of thermal

paste, or remove the cooling fan with extreme caution.)

Figure 4. Application of Thermal Grease to the processor.

Step 1-4. Connect the fan power wires to the header on the motherboard as shown in Figure 7.

Figure 7. Connecting the Fan Power Wires

Step 1-3.Once the thermal grease has been applied to the processor, the heatsink can be attached to

the processor. Align the heatsink assembly with the support frame mating with the backer

plate standoffs as shown in Figure 5&6.

Figure 5&6 Alignment of Heatsink

Assembly with Standoffs

- 18 -GA-K8VT800(Pro) Motherboard

English

Before installing the memory modules, please comply with the following conditions:

1. Please make sure that the memory used is supported by the motherboard. It is

recommended that memory of similar capacity, specifications and brand be used.

2. Before installing or removing memory modules, please make sure that the computer

power is switched off to prevent hardware damage.

3. Memory modules have a foolproof insertion design. A memory module can be installed

in only one direction. If you are unable to insert the module, please switch the direction.

Step 2: Installing Memory Modules

The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory

capacity and specifications. Memory modules are designed so that they can be inserted only in one

direction. The memory capacity used can differ with each slot.

DDR

Notch

Fig.1

The DIMM socket has a notch, so the DIMM memory module can

only fit in one direction. Insert the DIMM memory module vertically

into the DIMM socket. Then push it down.

Fig.2

Close the plastic clip at both edges of the DIMM sockets to lock the

DIMM module.

Reverse the installation steps when you wish to remove the DIMM

module.

Hardware Installation Process

English

- 19 -

DDR Introduction

Established on the existing SDRAM infrastructure, DDR (Double Data Rate) memory is a high

performance and cost-effective solution that allows easy adoption for memory vendors, OEMs, and

system integrators.

DDR memory is a great evolutionary solution for the PC industry that builds on the existing SDRAM

architecture, yet make the awesome advances in solving the system performance bottleneck by doubling

the memory bandwidth. Nowadays, with the highest bandwidth of 3.2GB/s of DDR400 memory and

complete line of DDR400/333/266/200 memory solutions, DDR memory is the best choice for building

high performance and low latency DRAM subsystem that are suitable for servers, workstations, and full

range of desktop PCs.

Recommended Memory Configurations (SS: Single -Sided, DS:Double-Sided)

Number of DIMMs

1

2

3

DIMM Socket Max. Memory Speed

DDR1 DDR2 DDR3

SS -- -- DDR 400

-- SS -- DDR 400

-- -- SS DDR 400

DS -- -- DDR 400

-- DS -- DDR 400

-- -- DS DDR 400

SS SS -- DDR 400

-- SS SS DDR 400

SS -- SS DDR 400

DS DS -- DDR 400

-- DS DS DDR 333

DS -- DS DDR 400

SS SS SS DDR 400

DS DS DS DDR 333

Please refer to the recommended memory configuration table below before installing memory.

- 20 -GA-K8VT800(Pro) Motherboard

English

Step 3-1: AGP Card Installation

Step 3 Install expansion cards

1. Read the related expansion card's instruction document before install the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer's chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

Please carefully pull out the small white-drawable bar at the end of the AGP slot when you try

to install / uninstall the AGP card. Please align the AGP card to the onboard AGP slot and

press firmly down on the slot. Make sure your AGP card is locked by the small white-

drawable bar.

La pagina sta caricando ...

Gigabyte GA-K8VT800 Manuale del proprietario

Questo manuale è adatto anche per

Gigabyte GA-K8VT800 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti