CARLO GAVAZZI EM511DINAV81XS1X Manuale del proprietario

EM511

Energy analyzer for single-phase systems

30/05/2023

USER MANUAL

Contents

2 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

This manual 3

EM511 4

Introduction 4

Description 4

Available versions 5

UCS (Universal Configuration Software) 5

Use 6

Interface 6

Introduction 6

Push buttons 6

Menu Overview 7

Measurement page 8

Information and warnings 8

SETUP menu 9

INFO menu 9

RESET menu 9

Commissioning 10

Introduction 10

QUICK SETUP menu 10

Menu description 15

Measurement pages 15

SETTINGS menu 16

INFO menu 17

RESET menu 18

Input, output and communication 19

Digital input 19

Digital output (version O1) 19

Modbus RTU port (version S1) 19

M-Bus port (version M1) 19

Essential information 20

Alarms 20

Introduction 20

Variables 20

Alarm types 20

DMD values 21

Average value calculation (dmd) 21

Integration interval 21

Example 21

LCD display 21

Home page 21

Backlight 21

Screensaver 22

Page filter 22

Restoring the factory settings 22

Restoring the settings using the RESET menu 22

Offset function 22

Setting some target values using the total reset function 22

Tariff management 24

Tariff management via digital input 24

Tariff management Modbus RTU 24

Maintenance and disposal 25

Troubleshooting 25

Alarms 25

Communication problems 25

Display problem 25

Download 26

Cleaning 26

Responsibility for disposal 26

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 3

This manual

Information property

CARLO GAVAZZI Controls SpA reserves the right to apply modifications or make improvements to the relative documentation

without the obligation of advance notice.

Safety messages

The following section describes the warnings related to user and device safety included in this document:

NOTICE: indicates obligations that if not observed may lead to damage to the device.

CAUTION! Indicates a risky situation which, if not avoided, may cause data loss.

IMPORTANT: provides essential information on completing the task that should not be neglected.

General warnings

This manual is an integral part of the product and accompanies it for its entire working life. It should be consulted for all

situations tied to configuration, use and maintenance. For this reason, it should always be accessible to operators.

NOTICE: no one is authorized to open the analyzer. This operation is reserved exclusively for CARLO GAVAZZI technical

service personnel.

Protection may be impaired if the instrument is used in a manner not specified by the manufacturer.

Service and warranty

In the event of malfunction, fault, requests for information or to purchase accessory modules, contact the CARLO GAVAZZI

branch or distributor in your country.

Installation and use of analyzers other than those indicated in the provided instructions and removal of the MABC module void the

warranty.

EM511

Introduction

EM511 is an energy analyzer for direct connection up to 45 A, for single-phase systems up to 240 V L-N. In addition to a digital

input, the unit is can be equipped, according to the model, with a static output (pulse or alarm), a Modbus RTU communication port

or an M-Bus communication port.

Description

N

345

12

B

F

A

D

A

D

C

G

E

Figure 1 EM511

Area Description

AVoltage inputs/Current inputs

BDIN - rail mounting bracket

CDisplay

DDigital input, digital output and communication connections

ELED

FSealable covers

GBrowsing and configuration buttons

4 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 5

Available versions

Part number Connection Output MID approval Swiss MID

approval

cULus

approval

EM511DINAV81XO1X Direct connection up to 45 A Digital output x

EM511DINAV81XS1X Direct connection up to 45 A RS485 Modbus

RTU

x

EM511DINAV81XM1X Direct connection up to 45 A M-Bus x

UCS (Universal Configuration Software)

UCS is available in desktop and mobile versions.

It may connect to EM511 via RS485 (RTU protocol, desktop version only).

UCS allows to:

lset up the unit (online or offline);

ldisplay the system state for diagnostic and setup verification purposes

Overview of the UCS functions:

lSetting up the system with energy meter connected (online setup)

lDefining the setup with energy non connected, then applying it later (offline setup)

lDisplaying the main measurements

lDisplaying the state of inputs and outputs

lDisplaying the state of the alarms

lRecording the measurements of selected variables

Use

Interface

Introduction

EM511 is organized into two menus:

lMeasurement pages: pages allowing to display the energy meters and the other electrical variables

lMain menu, divided into three sub-menus:

o» SETUP: pages allowing to set the parameters

o» INFO: pages displaying general information and the set parameters

o» RESET: pages allowing to reset the partial counters and the dmd calculation, or to restore the factory settings

Push buttons

Button Action

AlNext page

lIncrease value

lHome/previous menu (long press >3 s)

BlEnter menu

lConfirm

6 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 7

Menu Overview

Measurement page

Part Description

AMeasured values/data

BUnit of measurement

CInformation and diagnostics

Button Action

Information and warnings

Symbol Description

ALARM (blinking icon): the value of the variable has exceeded the threshold set.

COMMUNICATION: reading or writing command is addressed to EM511 serial communication state

(reception / transmission)

Total ON time

Partial meters

Exported energy (kWh-)

Imported energy (kWh+)

Unit of measurement

8 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 9

SETUP menu

Part Description

AParameter

BValue

Button Action

Next option / increase value

Confirm

INFO menu

Part Description

AParameter

BValue

Button Action

Next parameter

Enter / exit

RESET menu

Part Description

ASub-menu title, see “RESET menu”

BSelection (YES/NO)

Button Action

Next option

Confirm

Commissioning

Introduction

At power on, the device displays a configuration wizard, the QUICK SETUP, for a fast setup of the main parameters.

QUICK SETUP menu

This procedure is available when the instrument is switched on for the first time.

In the “QUICK SETUP?” starting page

Select... To...

Go run the QUICK SETUP procedure

no skip the procedure and no longer display the QUICK SETUP menu

LAtEr skip the procedure and display the QUICK SETUP menu at the next switch-on

Note: the available parameters depend on the model.

10 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 11

S1 models

Example 1: confirmation

Example 2: modification (address 4, parity EVEN, baudrate 19.2 kbps)

M1 models

Example 1: confirmation

Example 2: modification (primary address 1)

12 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 13

O1 models

Example 1: confirmation

Example 2: modification (pulse kWh+, duration 100 ms, 10 pulses/kWh)

14 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 15

Menu description

Measurement pages

Page Displayed measurements Description Note

1 kWh+ TOT Imported active energy

(TOTAL)

2 kWh- TOT Exported active energy

(TOTAL)

3 kW Active power

4 V L-N Voltage

5 A Current

6 PF Power factor

7 Hz Frequency

8 THD V Voltage THD

9 THD A Current THD

10 kvarh+ TOT Imported reactive energy

(TOTAL)

11 kvarh- TOT Exported reactive energy

(TOTAL)

12 kvar Reactive power

13 kVAh Apparent energy (TOTAL)

14 kVA Apparent power

15 kW dmd Demand active power

16 kW peak dmd Peak demand active power

17 kWh T1 Imported active energy, tariff 1

18 kWh T2 Imported active energy, tariff 2

19 h (kWh+) TOT Run hour meter (imported

energy)

20 h (kWh-) TOT Run hour meter (exported

energy)

21 h (ON time) TOT Run hour meter (ON time) TOT

22 kWh+ PAR Imported active energy

(PARTIAL)

23 h (kWh+) PAR Run hour meter (imported

energy, PARTIAL) PARTIAL

24 kWh- PAR Exported active energy

(PARTIAL)

25 h (kWh-) PAR Run hour meter (exported

energy, PARTIAL)

SETTINGS menu

This menu allows to set the parameters.

Page title Sub-menu Description Values Default values Note

Meas - Measurement mode A (easy connection)

B (bidirectional) A

DMD - DMD interval 1 min

5 min

10 min

15 min

20 min

30 min

60 min

15 min

inPut - Digital input Tariff (tariff

management)

Status (remote status)

P st (Start/stop partial

meters)

P res (partial meter

reset)

Status

RS485 Addr Address 1 to 247 1

PArity Parity NO/EVEN no

bAud Baudrate 9.6 kbps

19.2 kbps

38.4 kbps

57.6 kbps

115.2 kbps

9.6 kbps

StoP bit Stop bit 1 or 2 1

M bus Pri Add Primary address 0 to 250 0

bAud Baudrate 0.3 kbps

2.4 kbps

9.6 kbps

2.4 kbps

Output Fun Function Off

PuLSE (kWh+): pulse

output

linked to kWh+

PuLSE (kWh-): pulse

output

linked to kWh-

ALArM: linked to alarm

status

PuLSE (kWh+)

durAt Pulse duration 30 ms

100 m 30 ms

PuLSES Pulse weight

(pulses/kWh)

0.1/1/10/100/500/1000 1000

StAtuS Output status No (normally open)

Nc (normally closed) no

ALARM EnAbLE Enable ON/OFF OFF

VAriAb Monitored variable kW

kVA

Kvar

PF

A

V

kW

SEt 1 Set point 1 (activation) -1000.00 to 1000.00 0

Set 2 Set point 2 (deactivation) -1000.00 to 1000.00 0

dELAY Activation delay 0 to 1000 s 0

16 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 17

Page title Sub-menu Description Values Default values Note

dISPL LiGHt backlight ON (always on)

1 min

2 min

5 min

10 min

15 min

30 min

60 min

oFF: always off

ON

SC SAV Screensaver oFF

home: homepage

SLidE: slideshow

home

HOME homepage 1 to 25 1

PAGES Page filter ALL

FiLtEr ALL

PASS Password enabling for

the SETTINGS and

RESET menu

0 (not protected) to 9999 0 (not

protected)

bAcK --- - Exit - -

INFO menu

This menu allows to display the set parameters.

Page title Description Notes

YEAr Production year

Sn Serial number Sliding digits

FW rEV FW revision

MEAs Measurement type

dMd Demand calculation interval

Input Digital input function

Addr Address

bAud Baudrate (kbps)

PArity Parity

StoP b Stop bit

PriAdd M-Bus primary address

bAud M-Bus baudrate

SECAdd M-Bus secondary address

output Digital output function

StAtuS Current output status

durat Pulse output duration

PuLSE Output pulse weight

ALArM Alarm enabling

VAr Linked variable

SEt 1 Alarm activation set point

SEt 2 Alarm deactivation set point

dELAY Alarm activation delay

LIGHt Backlight timer

CHECKSuM Firmware checksum

RESET menu

This menu allows to reset the following settings:

Page Page title Description

1 PArtiAL It resets the partial meters

2 DMD It resets the dmd calculation

3 tAriFF It restores the factory settings

4 total It resets the total meters

5 FACtor It resets the device to factory settings

6 Back--- Back to main menu

18 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA 19

Input, output and communication

Digital input

The digital input can perform four functions:

Function Description Parameters

Tariff management Digital input used to manage the tariff

Digital input status Tariff

Open Tariff 1

Closed Tariff 2

-

Remote status Digital input is used to check the status via Modbus or M-Bus.

Digital input status Register 300h

Open 0

Closed 1

-

Partial meters start/stop Digital input is used to enable/disable the reset of partial meters

Digital input status Partial meter

Open Disabled (in pause)

Closed Enabled

-

Partial meter reset Digital input is used to enable/disable the increasing of partial meters

Digital input status Action

Open No action

Closed After 3 seconds, reset partial meters

-

Digital output (version O1)

The digital output can perform two functions:

Function Description Parameters

Alarm Output associated with the alarm Output state when no alarm is active

Pulse output Pulse transmission output for imported active

energy consumptions.

lLinked energy (kWh+, kWh-)

lPulse weight

lPulse duration

Modbus RTU port (version S1)

Modbus RTU communication port is used to transmit data to a Modbus master.

For further information about Modbus RTU communication refer to the communication protocol.

M-Bus port (version M1)

M-Bus communication port is used to transmit data to a M-Bus master (Carlo Gavazzi SIU-MBM or any third party M-Bus master).

For further information about M-Bus communication refer to the communication protocol.

Essential information

Alarms

Introduction

EM511manages a measured variable alarm. To set the alarm, define:

lthe variable to be monitored (VARIABLE)

lalarm activation threshold value (SET POINT 1)

lalarm deactivation threshold value (SET POINT 2)

lalarm activation delay (ACTIVATION DELAY)

Variables

The unit can monitor one of the following variables:

lactive power

lapparent power

lreactive power

lpower factor

lvoltage

lcurrent

Alarm types

Up alarm (Set point 1 ≥ Set point 2)

The alarm activates when the monitored variable exceeds the Set 1 value for a time equal to the activation delay (Delay) and

deactivates when the values drops below Set 2.

(s)

ON

Set 1

Set 2

Delay

20 EM511 - User manual | 30/05/2023 | CARLO GAVAZZI Controls SpA

La pagina sta caricando ...

CARLO GAVAZZI EM511DINAV81XS1X Manuale del proprietario

Questo manuale è adatto anche per

CARLO GAVAZZI EM511DINAV81XS1X Manuale del proprietario

in altre lingue

Documenti correlati