Lindy P16-IP Manuale utente

P16-IP KVM Switch

User Manual English

LINDY No. 32532

www.lindy.com

For Commercial Use Only

Tested to comply

with FCC Standards

1

About this manual

This manual is divided into four sections. The first section is an

introduction to the P16-IP; the second section deals with installing and

connecting the switch; the third section describes the basic operation of

the KVM switch from the locally connected console; the fourth section

describes operation via IP access.

2

Contents

SECTION 1..................................................................................................................................3

1.1 About the P16-IP..........................................................................................................4

1.2 Product Features .........................................................................................................5

1.3 Package Contents........................................................................................................6

1.4 Optional Cables and Accessories (not included) .....................................................6

SECTION 2..................................................................................................................................7

2.1 Product Information & Connections ..........................................................................8

2.2 Rackmount Installation ...............................................................................................9

2.3 Connecting an External Power Switch option...........................................................9

2.4 Cascading / Daisy Chaining of multiple KVM Switches .........................................10

SECTION 3................................................................................................................................11

3.1 KVM Switch Operation ..............................................................................................12

3.2 Keyboard Hotkey Selection ......................................................................................14

3.3 On Screen Display Menu (OSD) Port Selection.......................................................16

SECTION 4................................................................................................................................19

4.1 Configuration .............................................................................................................20

4.2 P16-IP Setup Tool ......................................................................................................21

4.3 Keyboard, Mouse and Video Configuration ............................................................23

4.4 Usage..........................................................................................................................26

4.5 Logging In ..................................................................................................................27

4.6 Navigation ..................................................................................................................28

4.7 Menu Options.............................................................................................................35

4.7.1 Remote Control...................................................................................................35

4.7.3 User Management...............................................................................................46

4.7.4 KVM Settings ......................................................................................................48

4.7.5 Device Settings...................................................................................................53

4.7.6 Maintenance........................................................................................................66

TROUBLESHOOTING...............................................................................................................70

KEY CODES..............................................................................................................................72

3

Section 1

Introducing

the P16-IP

Section 1 Introducing the P16-IP

4

1.1 About the P16-IP

Thank you for purchasing the LINDY P16-IP!

This advanced 16 port KVM switch allows direct control of up to 16 computers from a single

KVM (Keyboard, Video, and Mouse) console. Additionally, built-in KVM over IP technology

allows a remote operator to access the switch, and the computers connected to it, from almost

anywhere in the world using a simple web browser interface.

The P16-IP provides a non-intrusive solution for remote access and control because the

software runs on its embedded processors only, so there’s no interference with computer

operation, or impact on network performance. The P16-IP also features remote mass storage

support; a USB connection from the switch to the one of the connected computers allows virtual

storage to be set up on the host and accessed from the client.

The P16-IP supports computers equipped with PS/2 keyboard and mouse ports, and VGA

monitor connections. USB equipped PCs, Macs and SUN computers are also supported when

using the relevant USB to PS/2 adapter cable (LINDY No. 42866.)

The switch can be easily daisy chained with other LINDY P-series KVM switches (P4, P8 or

P16, it cannot be used with PXT switches) to support up to 128 computer connections in total,

all controlled from a single local console or via IP access.

Three methods of switching between the connected computers are available: by pressing the

front panel push buttons; by using keyboard hotkeys; or via OSD (On Screen Display). Hotkey

switching and OSD control is supported both locally and via the remote IP console. The

keyboard and mouse connections of all connected PCs and servers are emulated at all times.

This prevents error messages when switching between connected PCs.

IP Network

Multiple Servers

P16-IP

Local Console

Remote Access

Remote & local control of multiple computers

Section 1 Introducing the P16-IP

5

1.2 Product Features

 16 port KVM switch in a 1U, 19” rackmount size design

 Local console operation and KVM over IP control

 Support for LINDY mice and for all mice up to 5 buttons and 2 wheels with fully Microsoft

compatible drivers. Some advanced features and proprietary functions of wireless/RF mice

and keyboards with non-standard Microsoft® drivers may not be supported

 Remote mass storage device support

 Supports all commonly used operating systems

 Support for Mac and Sun computers with USB ports (an additional PS/2 to USB adapter i.e.

LINDY No. 42866 is needed)

 Hot Plug Support - add or remove PCs for maintenance without powering down the switch or

the PCs

 Very High Video Quality – Supports display resolutions of up to 1920x1440 for the local

console

 No Software Required - easy PC selection via On Screen Display Menu, Push Buttons or

Keyboard Hot Keys

 Eight character password protection and search function for server name

 Auto Scan Mode for monitoring computers and adjustable scan time from 5~99 seconds

 Keyboard status is restored when switching PCs

 LED Display for easy status monitoring

 Buzzer sound for port switching confirmation

 Uses special PS/2 + VGA cables with 15 Way Hi-Density connectors at the CPU Switch end

 Built-in daisy chain port allows additional LINDY P-series KVM switches to be connected to

support up to 128 computers

 Permanent keyboard and mouse emulation

Section 1 Introducing the P16-IP

6

1.3 Package Contents

 LINDY CPU Switch P16-IP KVM switch

 Power Adapter

 19” Rackmount Kit

 RS-232 Serial Cable

 USB Type A to B Cable

 KVM Daisy Chain Cable

 Utility & Manual CD

 Printed Quick Start Guides

1.4 Cables and Accessories (not included)

Apart from the computers to be connected, you will need a keyboard, monitor, and PS/2 mouse

to uses as a local console. You will also need dedicated LINDY KVM connection cables to

connect the computers to the switch. Standard 3-in-1 KVM cables can be used to daisy chain

the switch.

 P16-IP KVM Cable

o 2m LINDY No. 32506

o 3m LINDY No. 32507

o 5m LINDY No. 32508

 Daisy Chain 3-in-1 KVM Cable

o 1m LINDY No. 33711

o 2m LINDY No. 33712

o 3m LINDY No. 33713

 AT Keyboard to PS/2 Port Adapter Cable LINDY No. 70129

 USB to PS/2 Converter Cable LINDY No. 42866

Note: If some KVM cables are not long enough we recommend that the complete cable is

replaced with a longer length rather than using extension cables. Extension cables introduce

additional plug to socket connections, which can adversely affect the signal quality. Please bear

this in mind when using high resolutions or long distances.

P16-IP KVM Cable (15 Way HD Male to 15 Way HD Male + 2 x PS/2 Male)



7

Section 2

Hardware

Installation

Section 2 Hardware Installation

8

2.1 Product Information & Connection Guide

Make your connections to the switch as detailed below.

Ensure all devices are switched off before connecting. Once all connections have been made,

power on the switch, your monitor, and the computers in that order.

Port Push Button

Used for direct port selection. To access ports 1 to 8 simply

press the button; for ports 9 to 16, press the ‘↵

↵↵

↵’ button on the

front panel and the required port button simultaneously.

Port LED Display

When the LED labelled ‘P’ is illuminated green a computer attached to this port is

powered on. When the LED labelled ‘S’ is illuminated red, the KVM console is connected

to this port. If this LED flashes, the console is connected to this port, but either no

computer is attached, or the attached computer is not switched on.

Shift Button

This button allows ports 9 to

16 to be selected.

Bank Select Button

Pressing this button switches ‘banks’ and allows the computers connected

to ‘slave’ switches in a cascaded installation to be selected. The LED

above will display the selected bank. Pressing this button at the same time

as the port 8 button resets the switch.

Local Console Ports

Connect your keyboard,

monitor and mouse here.

10/100 RJ-45 Ethernet Port

Make your network connection here.

This port supports 10/100Mbps

connections and will auto-sense the

correct speed.

Serial Port

A modem or RS-232 Serial Terminal

can be connected here.

Computer Connection Ports

You can connect up to 16 computers to

these ports using dedicated KVM cables.

‘PC1’ refers to the first port, ‘PC2’ to the

second and so on...

Daisy Chain Ports

These ports allow a slave P-Series KVM switch

to be connected to the P16-IP using standard 3-

in-1 PS/2 & VGA KVM cable.

USB Port

Use the supplied cable to connect to a

computer for remote mass storage support.

Power Connection

Connect the supplied power adapter here.

Although the computers connected to the

switch may be able to supply enough power

to the unit, erratic operation may occur if the

power supply is not used.

Section 2 Hardware Installation

9

2.2 Rackmount Installation

Before you start please verify that all parts are

included according to the package contents.

If you want to install the CPU Switch in a 19” server

rack please attach the enclosed 19” rackmount

brackets using the included screws.

2.3 Connecting an External Power Switch option

At the time of writing (November 2006) the P16-IP supports the following external power switch

options. Please refer to the individual manufacturers manuals for advice on connecting to the

P16-IP.

 Avocent SPC1 800/1600

 Sentry In-Line Power Module

 Leaning ePowerSwitch

Section 2 Hardware Installation

10

Note: If video quality

deteriorates you can add

a VGA amplifier between

the fifth and the sixth

KVM switch to enhance

the VGA signal. (see

www.lindy.com for

appropriate products)

2.4 Cascading / Daisy Chaining of multiple KVM Switches

The P16-IP can be cascaded with LINDY P-Series CPU switches only. It should not be used

with LINDY PXT-Series CPU Switches. For all cascaded installations, the P16-IP should always

be used as the MASTER switch.

To connect an additional switch to the MASTER (or previous) switch, you must use a standard

(VGA + 2 x PS/2) 3-in-1 KVM cable, all connectors male.

Step 1 - Connect the local console

Connect your keyboard, mouse and monitor to the console ports of the P16-IP MASTER KVM

Switch.

Step 2

Use one end of a 3-in-1 KVM cable to connect the daisy chain port of the MASTER/previous

KVM Switch and the other end to the console port of the next SLAVE switch.

Step 3 - Cascading

Repeat the previous step to daisy chain mores switches. Each individual switch in the chain

represents a different Bank. The MASTER switch is Bank 1 and each cascaded SLAVE follows

on as Bank 2, 3, 4 etc. to a maximum of eight banks/switches.

Step 4 – Resetting the Switches

After you have connected and switched on the SLAVE switches and computers, all of the KVM

switches must be reset. First, reset the SLAVE switch at the end of the daisy chain and then

reset all of the other SLAVE switches up to the MASTER P16-IP switch.

To reset the switch, press and hold the Bank button and P8 button on the front panel of the

switch.

Each SLAVE switch should now show a dash in its BANK display.

Now, reset the MASTER switch - it will show a 1 in the BANK display. Each SLAVE switch

BANK display will now change to a number according to its position in the daisy chain.

Bank 1 (Master)

Bank 3...to a maximum of 8

Cascading KVM Switches

11

Section 3

KVM Switch

Operation

Section 3 KVM Switch Operation

12

3.1 KVM Switch Operation

Password Security

When you power on the P16-IP it will ask you for a password. The default password is eight

zeros –“00000000”. Please key in eight zeros in the password field.

Note: Please don’t change the password until you are familiar with the operation of the OSD

menu – i.e. keep the default password “00000000”. Otherwise, if you forget the password, you

will need to send the switch back to LINDY for maintenance to clear the password.

Hot Plug Support

The P16-IP supports a “Hot Plug” function for easy addition or removal of PCs. The user can

arrange or maintain the PCs as follows:

a. A PC can be disconnected and reconnected to the same or a different port of the KVM

switch without having to power it off as long as it is currently not connected to the console.

b. The mouse driver of the PC has to support the hot plug function or the computer may need

to be rebooted when it is reconnected.

c. You can unplug your mouse or keyboard from the console port and plug it back in at any

time. You should not use different types of mice when doing this

d. A SLAVE KVM switch can be added or removed at any time, but after adding or removing a

switch you must reboot all of the switches. You DO NOT need to reboot the computers.

Please note: Some Operating Systems such as certain Unix versions are unable to

support the “Hot Plug” function. If you Hot Plug when using this kind of O.S., it may cause

unpredictable operation or may shut down the PC. Before attempting to use the Hot Plug

feature, please make sure you’re O.S. and mouse software driver support the Hot Plug

feature.

Important note:

Your monitor will only display one PC signal at any one time. All

keyboard and mouse commands are sent to this PC only. After initial power up, port 1 is

active by default.

When a PC is connected to the currently selected port and it is not switched on,

or is in sleep mode, the monitor will not display any signal.

Section 3 KVM Switch Operation

13

Computer / Port Selection

You can select the computer you want to access in three different ways:

 Front panel push button selection

 Keyboard hotkey selection

 On screen display menu selection

Port LED Display

The front panel of the switch has two LEDs for each port.

When the LED labelled “P” is illuminated GREEN a computer attached to this port is powered

on. When the LED labelled “S” is illuminated RED, the KVM console is connected to this port. If

this LED flashes, the console is connected to this port but either no computer is attached, or the

attached computer is not switched on.

3.1.5 Front panel push button selection

You can select a computer by pressing the appropriate port push button. Each push button

refers to two ports. To access ports 1 to 8 simply press the button; to access ports 9 to 16 you

must push the button marked “↵” and the required port button simultaneously.

For cascaded KVM Switches you can ONLY use the port selection push buttons on the

MASTER P16-IP Switch to switch the SLAVES (you can also switch via OSD or keyboard

hotkey).

Section 3 KVM Switch Operation

14

3.2 Keyboard Hotkey Selection

You can also conveniently select the computer to be accessed and displayed by switching ports

through simple keyboard key sequences. To send commands to the KVM switch, the “SCROLL

LOCK” key must be pressed twice within 2 seconds. You will hear a beep to confirm that

the keyboard is in hotkey mode. If you have not pressed any key in hotkey mode within 2

seconds, the keyboard will return back to Operating System control status.

Direct Port Selection / Keyboard Hot Key Commands:

Within 2 seconds

+ + = Previous Port

or

+ + = Next Port

KVM Switch/Bank Selection:

The P16-IP supports cascading of up to 8 KVM Switches (Banks). Therefore, when using direct

hotkey port selection you must include the key sequence for the KVM Switch/Bank:

+

Example: To access a computer attached to Port 6 of the first KVM Switch you should

press the following hotkeys:

+

To use hotkey switching to access another KVM Switch / Bank:

+ + = Previous Bank

+ + = Next Bank

Scroll

Lock

Scroll

Lock





Tip: Hold the arrow key down,

or press multiple times, to cycle

through the ports

Scroll

Lock

Scroll

Lock

Bank

No 1~8

Port No.

01~04 (4 port)

01~08 (8 port)

01~16 (16 port)

Important Note:

Always keep in

mind to include

leading zeros for

all ports below 10!

i.e.104 for Port 4 of

the first switch.

Bank no. and

Port no. selection

must be made

using the

numeric keys on

the keyboard.

Keys on the

numeric keypad

are not available

as hot key

commands!

Scroll

Lock

Scroll

Lock

Scroll

Lock

Scroll

Lock

Page

Up

Page

Down

(

This will only work if a daisy

chained KVM Switch is present)

Scroll

Lock

Scroll

Lock

1 0 6

Section 3 KVM Switch Operation

15

Auto Scan mode:

+ + =

Auto Scan (Press any key to exit Auto Scan Mode)

Beeper Function (Enables and Disables beep during Auto Scan):

+

= Beeper

Scroll

Lock

Scroll

Lock

S

Scroll

Lock

Scroll

Lock

B

Section 3 KVM Switch Operation

16

3.3 On Screen Display Menu (OSD) Port Selection

The On Screen Display menu provides a lot of information about the P16-IP and the attached

computers, and offers advanced administration features and full KVM Switch control to the user.

To invoke the On Screen Display Menu press the following hotkeys:

+ + = On Screen Display Menu



The OSD menu closes down automatically after a specified time period, which can be set in the

OSD settings menu. The time selected can be between 5 and 99 seconds

The OSD menu can be invoked even when the P16-IP is currently switched to a port with no

connected or a non-powered on PC. In this case the resolution of OSD menu is fixed to a 1024

X 768 virtual frame.

If you wish to, you can restore the factory default values of the OSD. Please note this does not

include resetting the password! The bank LED display on the front panel will flash during the

memory refresh process.

+ + = OSD setting back to factory default value

(Note: Not including password)

An OSD overlay window will be displayed on the screen

during the memory refresh process

When the OSD values have been reset back to factory default, the bank LED on the front panel

will stop flashing.

The OSD also allows you to give each attached computer its own name. A name search

function is also available from the OSD:

+ + = Search the same PC name

(Note: Search PC name starting from 1st PC port)

You can type in one character up to a complete name. The

upper part of the window will display all computer names

that match one by one. You can use the UP/DOWN cursor

keys to toggle through this name list.

Press ENTER to switch to the computer displayed in the

upper window.

ESC closes the window

Scroll

Lock

Scroll

Lock

Space Bar

ROM REFLASH

Scroll

Lock

Scroll

Lock

R

Scroll

Lock

Scroll

Lock

F

F I N D : 

Section 3 KVM Switch Operation

17

The OSD Menu displays the following screen

a. You can toggle between the 3 parts of the OSD menu (Bank PC names, KVM Switch

Settings) using the TAB key. The lower light blue part of the OSD lists keyboard controls.

b. The 1st part of the OSD window

line bar is the bank or KVM Switch

number

c. The 2nd part (dark blue) is the

attached PC name list. You will find

the system number list from 01 to

04 (for 4 port version) or from 01 to

08 (for 8 port version) or from 01 to

16 (for 16 port version). You can

rename your PCs here (maximum 8

characters). The factory default PC

name is “SYSTEM 01”, “SYSTEM

02”, etc.

d. The sun symbol “” next to the

PC name indicates that the

attached computer is powered on.

e. You can use the CURSOR

keys (up arrow, down arrow, left

and right arrow) to select the port

you want to access and press the

ENTER key to switch.

f. Use the “PgUp” or “PgDn” key to switch to another daisy chained KVM Switch / Bank. This

function only works when another KVM Switch/Bank is connected.

g. To change the name of a

computer, select the port and press

the “INS” key to edit the name.

Press the “Enter” key to save it.

h. To access the third part of the

OSD containing OSD, SCAN,

CHANGE PASSWORD, CONSOLE

ON/OFF, etc. press the “TAB” key

The TAB key toggles between the fields. Simply overwrite the fields with your chosen values.

i. OSD means that the OSD window is displayed on your monitor for 10 sec. You can modify

this value from 05 sec to 99 sec. Default is 10 sec.

01

SYSTEM 01 02

SYSEM 02 





BANK : 1

01

SYSTEM 01 02

SYSTEM 02 





03

SYSTEM 03 04

SYSTEM 04

05

SYSTEM 05 06

SYSTEM 06

07

SYSTEM 07 08

SYSTEM 08

09

SYSTEM 09 10

SYSTEM 10

11

SYSTEM 11 12

SYSTEM 12

13

SYSTEM 13 14

SYSTEM 14

15

SYSTEM 15 16

SYSTEM 16

OSD : 10 SEC. CHANGE PASSWORD

SCAN: 10 SEC. CONSOLE ON/OFF

ESC : QUIT ENTER :COMPLETE

TAB : NEXT INSERT :EDIT





/



: SELECT PORT

PgDn/PgUp: BANK SELECT

OSD : 10 SEC. 





CHANGE PASSWORD

SCAN: 10 SEC. CONSOLE ON/OFF

Section 3 KVM Switch Operation

18

j. SCAN displays the scan duration per channel in Auto Scan Mode. The default SCAN time

is 10 sec., the maximum scan time can be set to 99 sec, it cannot be less then 5 sec.

k. CONSOLE ON/OFF is used to prevent unauthorized use of the console. “CONSOLE ON”

means that any user can access the console. “CONSOLE OFF” (factory default) means that

any user will have to enter the password before getting access. When the password is entered

correctly the CONSOLE status will be set to ON. To lock the console again the status has to be

changed from CONSOLE ON to OFF via OSD. Also if the current CONSOLE state is ON and

you reset the KVM switch, the CONSOLE will be reset to the OFF state.

l. CHANGE PASSWORD is used

to set a new password. The factory

default is 8 digits “00000000”.

To change the password you have

to input the old password and then

type in the new password twice, to

prevent mistyping. The maximum

password length is eight digits.

Make sure you do not forget the

password. Otherwise you will have

to send the KVM Switch to LINDY

for maintenance.

Finally you will see the confirmation

message that the new password is

set.

When you have switched to a certain port on the KVM Switch the keyboard and mouse

commands are directed to the attached computer and its monitor signal is displayed on the

screen. In this overlay window from the OSD you will see some basic

information for the selected computer / port. The OSD shows

the port number; the status of the attached computer - “”,

to indicate that this computer is online and powered on; and the computer name.

You can close almost any overlay OSD window by simply pressing the ESCAPE key.

ENTER PASSWORD : 

ESC : QUIT ENTER :

COMPLETE

ENTER NEW PASSWORD : 

ESC : QUIT ENTER :

COMPLETE

NEW PASSWORD COMPLETE

ESC : QUIT ENTER :

COMPLETE

102 SYSTEM 02

RETYPE NEW PASSWORD : 

ESC : QUIT ENTER :

COMPLETE

19

Section 4

IP Access

Configuration

& Operation

La pagina sta caricando ...

Lindy P16-IP Manuale utente

Lindy P16-IP Manuale utente

in altre lingue

Documenti correlati

Altri documenti