Moog Videolarm FDW75 Installation And Operation Instructions Manual

Marca: Moog Videolarm

Modello: FDW75

Categoria: Accessori per telecamere di sicurezza

Tipo: Installation And Operation Instructions Manual

Questo manuale è adatto anche per

Before a t t e m pti n g t o co n n e c t o r op e r a te t h i s p ro d u c t ,

pl e a s e rea d t h e s e in s t r u c t i o ns c o m p l ete l y.

81-IN5358R1

www.videolarm.com

F D W 7 5

Fusion Dome (Outdoor Wall Mount with Housing)

Installation and Operation Instructions for the following models:

FDW75C2N IP Network Ready 7” Outdoor dome hsg w/wall mount, clear dome, w/24Vac input, heater/

blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.

FDP75C2N IP Network Ready 7” Outdoor dome hsg w/pendant mount, clear dome, w/24Vac input, heater/

blower, fan an IP Network PTZ camera,120 to 24Vac transformer.

IFDW75CN IP Network Ready 7” Indoor dome hsg w/wall mount, clear dome, w/24Vac input, heater/

blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.

IFDP75CN IP Network Ready 7” Indoor dome hsg w/pendant mount, clear dome, w/24Vac input, heater/

blower, fan an IP Network PTZ camera,120 to 24Vac transformer.

FDW75C2NE IP Network Ready 7” Outdoor dome hsg w/wall mount, clear dome, w/24Vac input, heater/

blower, fan an IP Network PTZ camera. (European Model)

FDP75C2NE IP Network Ready 7” Outdoor dome hsg w/pendant mount, clear dome, w/24Vac input, heater/

blower, fan an IP Network PTZ camera. (European Model)

FDW75C2N/AC IP Network Ready 7” Outdoor dome hsg w/wall mount, clear acrylic dome, w/24Vac input, heater/

blower, fan an IP Network PTZ camera, 120 to 24Vac transformer.

FDP75C2N/AC IP Network Ready 7” Outdoor dome hsg w/pendant mount, clear dome, w/24Vac input, heater/

blower, fan an IP Network PTZ camera,120 to 24Vac transformer.

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read Instructions - All the safety and operating

instructions should be read before the unit is

operated.

2 Retain Instructions - The safety and operating

instructions should be retained for future

reference.

3 Heed Warnings - All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions - All operating and user

instructions should be followed.

5 Electrical Connections - Only a qualified

electrician should make electrical connections.

6 Attachments - Do not use attachments not

recommended by the product manufacturer as

they may cause hazards.

7 Cable Runs - All cable runs must be within

permissible distance

8 Mounting - This unit must be properly and securely

mounted to a supporting structure capable of

sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualified

installer.

b. The installation should be in compliance with

local codes.

c. Care should be exercised to select suitable

hardware to install the unit, taking into

account both the composition of the mounting

surface and the weight of the unit.

Be sure to periodically examine the unit and the

supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the

foregoing could result in the unit separating from the

support structure and falling, with resultant damages or

injury to anyone or anything struck by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make

future shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us

at the following number:

The lightning flash with an arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of non-insulated “dangerous voltage”

within the product’s enclosure that may be

of sufficient magnitude to constitute a risk

of electric shock to persons.

Este símbolo se piensa para alertar al usuario a la

presencia del “voltaje peligroso no-aisIado” dentro del

recinto de los productos que puede ser un riesgo de

choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la

presence “de la tension dangereuse” non-isolée dans la

clôture de produits qui peut être un risque de choc

électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença

“di tensão perigosa non-isolada” dentro do cerco dos

produtos que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla

presenza “di tensione pericolosa” non-isolata all’interno

della recinzione dei prodotti che può essere un rischio di

scossa elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones

importantes en la literatura que acompaña la

aplicación.

Ce symbole de point d’exclamation est prévu pour

alerter l’utilisateur à la presence des instructions

importantes dans la littérature accompagnant

l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der

Literatur alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido

alertar o usuário à presença de instruções importantes

na literatura que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti

nella letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualified installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the

unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including amplifiers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specified by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the

integrity of the installation is intact. Failure to comply with the foregoing could result in the

unit separating from the support structure and falling, with resultant damages or injury to

anyone or anything struck by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make

future shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us

at the following number:

The lightning flash with an arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of non-insulated “dangerous voltage”

within the product’s enclosure that may be

of sufficient magnitude to constitute a risk

to persons.

Este símbolo se piensa para alertar al usuario a la

presencia del “voltaje peligroso no-aisIado” dentro del

recinto de los productos que puede ser un riesgo de

choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la

presence “de la tension dangereuse” non-isolée dans la

clôture de produits qui peut être un risque de choc

électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença

“di tensão perigosa non-isolada” dentro do cerco dos

produtos que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla

presenza “di tensione pericolosa” non-isolata all’interno

della recinzione dei prodotti che può essere un rischio di

scossa elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones

importantes en la literatura que acompaña la

aplicación.

Ce symbole de point d’exclamation est prévu pour

alerter l’utilisateur à la presence des instructions

importantes dans la littérature accompagnant

l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der

Literatur alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido

alertar o usuário à presença de instruções importantes

na literatura que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti

nella letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING TO

QUALIFIED SERVICE PERSONNEL.

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read Instructions - All the safety and operating

instructions should be read before the unit is

operated.

2 Retain Instructions - The safety and operating

instructions should be retained for future

reference.

3 Heed Warnings - All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions - All operating and user

instructions should be followed.

5 Electrical Connections - Only a qualified

electrician should make electrical connections.

6 Attachments - Do not use attachments not

recommended by the product manufacturer as

they may cause hazards.

7 Cable Runs - All cable runs must be within

permissible distance

8 Mounting - This unit must be properly and securely

mounted to a supporting structure capable of

sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualified

installer.

b. The installation should be in compliance with

local codes.

c. Care should be exercised to select suitable

hardware to install the unit, taking into

account both the composition of the mounting

surface and the weight of the unit.

Be sure to periodically examine the unit and the

supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the

foregoing could result in the unit separating from the

support structure and falling, with resultant damages or

injury to anyone or anything struck by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make

future shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us

at the following number:

The lightning flash with an arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of non-insulated “dangerous voltage”

within the product’s enclosure that may be

of sufficient magnitude to constitute a risk

of electric shock to persons.

Este símbolo se piensa para alertar al usuario a la

presencia del “voltaje peligroso no-aisIado” dentro del

recinto de los productos que puede ser un riesgo de

choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la

presence “de la tension dangereuse” non-isolée dans la

clôture de produits qui peut être un risque de choc

électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença

“di tensão perigosa non-isolada” dentro do cerco dos

produtos que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla

presenza “di tensione pericolosa” non-isolata all’interno

della recinzione dei prodotti che può essere un rischio di

scossa elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones

importantes en la literatura que acompaña la

aplicación.

Ce symbole de point d’exclamation est prévu pour

alerter l’utilisateur à la presence des instructions

importantes dans la littérature accompagnant

l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der

Literatur alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido

alertar o usuário à presença de instruções importantes

na literatura que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti

nella letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS

VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows:

PRODUCT CATEGORY PARTS LABOR

All Enclosures and Electronics Three (3) Years Three (3) Years

Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan

Poles/PoleEvators Three (3) Years Three (3) Years

Warrior/Q-View/I.R. Illuminators/SView Five (5) Years Five (5) Years

Controllers Three (3) Years Three (3) Years

Power Supplies Three (3) Years Three (3) Years

Accessory Brackets Three (3) Years Three (3) Years

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Videolarm Inc.

Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package an equal degree of protection with a

RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Videolarm will return the repaired Product freight prepaid to Purchaser. Videolarm is not obligated to provide

Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions:

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice

with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the

warranty period. If after investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall pay Videolarm

for the cost of investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall

extend the warranty period as to the entire Product. The warranty on the repaired part only shall be in for a period of ninety (90) days

following the repair or replacement of that part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair

any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service

during the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts

of God (i.e., hurricanes, earthquakes), failure of the end-user to follow the directions outlined in the product instructions, failure of the

end-user to follow the maintenance procedures recommended by the International Security Industry Organization, written in product instructions,

or recommended in the service manual for the Product. Furthermore, Videolarm shall have no liability where a schedule is for regular

replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted repair by

personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original

(trademark, serial number) markings have been defaced, altered, or removed. Videolarm excludes from warranty coverage Products sold

AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser. All software and accompanying

documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided

otherwise in any documentation or license agreement furnished with the Product.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH

REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE

STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM

PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT.

LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF

FDW75

24 VAC

26 Watts

Accessories: Heater: 25 Watts, Blower: 1 Watt

Camera Power: 40 Watts Max

Tools Required: .100” Flat Head Screwdriver

Phillips Head Screwdriver

24 VAC

26 vatios

Accesorios: Calentador: 25 Vatios, Soplador: 1 vatio

Energía De la Cámara fotográfica: 40 vatios Max

Las Herramientas Requirieron: Destornillador Principal Plano Del

100". Destornillador Principal Phillips.

24 VCA

26 watts

Accessoires : Réchauffeur : 25 Watts, Ventilateur : 1 watt

Puissance D'Appareil-photo : 40 watts Max

Les Outils Ont exigé : Tournevis Principal Plat De 100".

Tournevis Principal Phillips.

24 VAC

26 Watt

Zusatzgeräte: Heizung: 25 Watt, Gebläse: 1 Watt.

Kamera-Energie: 40 Watt Max

Werkzeuge Erforderten: 100"Flacher Hauptschraubenzieher.

Kreuzkopfhauptschraubenzieher.

24 VAC

26 watts

Acessórios: Calefator: 25 Watts, Ventilador: 1 watt.

Poder Da Câmera: 40 watts Max

Ferramentas Requeridas: Chave de fenda Principal Lisa Do

100". Chave de fenda Principal Phillips.

24 VCA.

26 watt

Accessori: Riscaldatore: 25 Watt, Ventilatore: 1 watt.

Alimentazione Della Macchina fotografica: 40 watt Max

Gli Attrezzi Hanno richiesto: Cacciavite Capo Piano Del 100".

Cacciavite Capo "phillips".

Electrical Specifications

IFDP75CFN

FDW75CFN (INDOOR ONLY)

Power 24VAC

Class 2 Only

24 VAC

No power options provided.

Power required for camera only.

24 VAC

Ningunas opciones de la energía proporcionaron.

Energía requerida para la cámara fotográfica solamente.

24 VCA

Option de puissance n'a pas fourni.

Puissance requise pour l'appareil-photo seulement.

24 VAC

Keine Energie Wahlen stellten zur Verfügung.

Energie erfordert für nur Kamera.

24 VAC

Nenhumas opções do poder fornecidas.

Poder requerido para a câmera somente.

24 VAC

Nessun'opzione di alimentazione ha fornito.

Alimentazione richiesta per la macchina fotografica soltanto.

Indoor Models IFDP75CN/ IFDP75CN Include NO Power

Accessories

International Models FDW75C2NE/ FDP75C2NE Include NO

Power Transformer

Français

Deutsch

Italiano

Portuguese

Español

English

Contents of Box

*** WALL MOUNT FOR (W) MODELS.

Securely mount unit to wall or to appropriate

adapter bracket.

• Monte con seguridad la unidad a la pared o al

soporte apropiado del adaptador.

• Montez solidement l'unité au mur ou à la parenthèse

appropriée d'adapteur.

• Bringen Sie sicher Maßeinheit zur Wand oder zum

passenden Adapterhaltewinkel an.

• Monte firmemente a unidade à parede ou ao suporte

apropriado do adaptador.

• Monti saldamente l'unità alla parete o alla staffa

adatta dell'adattatore.

If using conduit connect, connect to

incoming conduit fitting.

• Si usa el conducto conecte, conecte con la guar-

nición entrante del conducto.

• Si à l'aide du conduit reliez, reliez à l'ajustage de

précision entrant de conduit.

• Wenn Sie Rohr verwenden, schließen Sie an, schließen

Sie an ankommende Rohrbefestigung an.

• Se usando a canalização conecte, conecte ao

encaixe entrante da canalização.

• Se per mezzo del condotto colleghi, colleghi al mon-

taggio ricevuto del condotto.

Open access door to access power and

control connectors.

• Abra la puerta de acceso en los conectadores de la

energía y de control del acceso.

• Ouvrez la porte d'accès aux connecteurs de

puissance et de commande d'accès.

• Öffnen Sie Zugang zur Zugang Energie und zu den

Geräteanschlüssen.

• Abra a porta de acesso aos conectores do poder e

de controle do acesso.

• Apra il portello di accesso ai connettori di alimentazi-

one e di controllo di accesso.

Make wire connection as they are required

for your needs.

• Haga la conexión del alambre como se requieren

para sus necesidades.

• Établissez le rapport de fil comme ils sont exigés pour

vos besoins.

• Stellen Sie Leitung Beziehung her, wie sie für Ihre

Notwendigkeiten angefordert werden.

• Faça a conexão do fio como são requeridos para suas

necessidades.

• Faccia il collegamento del legare come sono richiesti

per i vostri bisogni.

WALL MOUNTING

1 2

3 4

Securely mount bracket to wall. Pull wiring

through bracket and position grommet as shown.

• Con seguridad soporte del montaje a emparedar. Tire del cableado

a través del soporte y del ojal de la posición según lo demostrado.

• Solidement parenthèse de bâti à murer. Tirez le câblage par la

parenthèse et le canon isolant de position comme montré.

• Sicher Einfassung Haltewinkel wall. Ziehen Sie Verdrahtung durch

Haltewinkel und Position Gummimuffe, wie gezeigt.

• Firmemente suporte da montagem a wall. Puxe a fiação através do

suporte e do ilhó da posição como mostrado.

• Saldamente staffa del supporto da wall. Tiri i collegamenti tramite la

staffa ed il gommino di protezione di posizione come indicato.

Screw the (2) bolts into the coupling.

• Atornille (2) los pernos en el acoplador.

• Vissez (2) les boulons dans l'accouplement.

• Schrauben Sie die (2) Schraubbolzen in die Koppe-

lung.

• Parafuse (2) os parafusos no acoplamento.

• Avviti (2) i bulloni nell'accoppiamento.

Wrap Teflon tape around the pipe threads

to ensure a tight seal.

• La cinta del Teflon del abrigo alrededor de la pipa rosca

para asegurar un sello apretado.

• La bande de teflon d'enveloppe autour de la pipe filète

pour assurer un joint serré.

• Verpackung Teflonklebeband um das Rohr verlegt, um

eine feste Dichtung sicherzustellen.

• A fita adesiva do Teflon do envoltório em torno da

tubulação enfía para assegurar um selo apertado.

• Il nastro del Teflon dell'involucro intorno al tubo filetta per

accertare una guarnizione stretta.

Screw the coupling onto the pipe threads

until it is hand tight.

• Atornille el acoplador sobre los hilos de rosca de la pipa

hasta que es mano firmemente.

• Vissez le couplage sur les fils de pipe jusqu'à ce que ce

soit main fortement.

• Schrauben Sie die Koppelung auf die Rohrgewinde, bis

es Hand fest ist.

• Parafuse o acoplamento nas linhas da tubulação até

que esteja mão firmemente.

• Avviti l'accoppiamento sui filetti del tubo fino a che non

sia fortemente mano.

FOR PENDENT/

WALL MOUNTING

Loop the lanyard over the set screw to

temporarily hold housing.

• Coloque el acollador sobre el tornillo de presión para

celebrar temporalmente la cubierta.

• Faites une boucle la lanière au-dessus de la vis de réglage

pour tenir temporairement le logement.

• Schlingen Sie die Abzuglinie über der Klemmschraube, um

Gehäuse vorübergehend zu halten.

• Dê laços no colhedor sobre o parafuso de fixação para

prender temporariamente a carcaça.

• Colleghi la cordicella in circuito sopra la vite di arresto

temporaneamente per tenere l'alloggiamento.

Make the appropriate wiring connections

from the dome to the gooseneck.

• Haga las conexiones apropiadas del cableado de la bóveda

al gooseneck.

• Établissez les rapports appropriés de câblage à partir du dôme

au col de cygne.

• Stellen Sie die passenden Verdrahtung Beziehungen von der

Haube zum gooseneck her.

• Faça as conexões apropriadas da fiação da abóbada ao

gooseneck.

• Faccia i collegamenti adatti dei collegamenti dalla cupola al

gooseneck.

Undo the lanyard, pull housing up and twist

secure with the locking bolt and washers.

• Deshaga el acollador, tire de contener para arriba y tuerza seguro

con el perno y las arandelas de fijación.

• Défaites la lanière, tirez loger vers le haut et tordez bloqué avec le

boulon et les rondelles de fermeture.

• Annulieren Sie die Abzuglinie, ziehen Sie oben unterbringen und

verdrehen Sie sicheres mit dem verriegelnschraubbolzen und den

Unterlegscheiben.

• Undo o colhedor, puxe abrigar acima e torça seguro com o

parafuso e as arruelas travando.

• Undo la cordicella, tiri l'alloggio in su e torca sicuro con il bullone e

le rondelle di bloccaggio.

Slide the grommet down over the coupling to prevent

water from entering and complete the assembly.

• Resbale el ojal abajo sobre el acoplador para evitar que el agua

entre y para terminar a la asamblea.

• Glissez le canon isolant vers le bas au-dessus de l'accouplement

pour empêcher l'eau d'entrer et pour accomplir l'assemblée.

• Schieben Sie die Gummimuffe unten über der Koppelung, um zu

verhindern, daß Wasser und die Versammlung durchzuführen

hereinkommt.

• Deslize o ilhó para baixo sobre o acoplamento para impedir que a

água entre e para terminar o conjunto.

• Faccia scorrere il gommino di protezione giù sopra l'accoppiamento

per impedire l'acqua entrare e per completare il complessivo.

Green

Yellow

Orange

Red

Camera

Power

Accessory

Power

Camera = red & orange wires to terminal

Heater/Blower = yellow & green wires to terminal

• Cámara fotográfica = alambres rojos y anaranjados al

terminal Heater/Blower = alambres del amarillo y del verde

al terminal

• Appareil-photo = fils rouges et oranges à la borne

Heater/Blower = fils de jaune et de vert à la borne

• Kamera = rote u. orange Leitungen zum Anschluß

Heater/Blower = Gelb- u. Grünleitungen zum Anschluß

• Câmera = fios vermelhos & alaranjados ao terminal

Heater/Blower = fios do amarelo & do verde ao terminal

• Macchina fotografica = legare rossi & arancioni al terminale

Heater/Blower = legare di verde & di colore giallo al termi-

nale

AWG

,5 ,75 1,0 1,5 2,5 4 6

22 20 18 16 14 12 10

The beam angle may be adjusted on the

bottom of the unit.

• Éstos se recomiendan las distancias máximas para

24VAC con una gota del voltage del 10%.

• Ceux-ci sont recommandés des distances maximum

pour 24VAC avec une chute de tension de 10%.

• Diese werden maximale Abstände für 24VAC mit

einem 10% Spannungsabfall empfohlen.

• Estes são recomendados distâncias máximas para

24VAC com uma queda de tensão de 10%.

• Questi sono suggeriti distanze massime per 24VAC

con una differenza de potenziale di 10%.

These are recommended maximum distances

for 24VAC with a 10% voltage drop.

RJ45

BNC

24VAC

Camera

Heater/Blower

Red

Orange

Yellow

Green

POWER

Max 40 Watts

26 Watts

1/0

Alarm 1

Alarm 2

Alarm 3

Common

Blue

Violet

Gray

White

Make the appropriate male and female connections. Indoor model does not include pre-run cables.

• Haga las conexiones masculinas y femeninas apropiadas. El modelo de interior no incluye pre-funciona los cables.

• Établissez les rapports masculins et femelles appropriés. Le modèle d'intérieur n'inclut pas pré-courent des câbles.

• Stellen Sie die passenden männlichen und weiblichen Beziehungen her. Innenmodell schließt nicht vor-laufen lassen Kabel

ein.

• Faça as conexões masculinas e fêmeas apropriadas. O modelo indoor não inclui pre-funciona cabos.

• Faccia i collegamenti maschii e femminili adatti. Il modello dell'interno non include pre-fa funzionare i cavi.

3026 Mounting

Plate

Mounting

Hole

Mounting

Hole

Mounting Hole

Axis 214

(52

) 2"

Captive

Screw

(3) #8 x 3/8”

Install the camera to the mounting plate using (3) 3mm x 12mm bolts and lock washers. Place (3) #8x3/8”

screws on the spacers and line up the mounting slots. Slide plate in and secure.

• Instale la cámara fotográfica a la placa de montaje usando (3) los pernos de 3m m x de 12m m y las arandelas de cerradura.

Coloque los tornillos de (3) del # 8x3/8"en los espaciadores y alinee las ranuras de montaje. Resbale la placa adentro y

asegúrela.

• Installez l'appareil-photo sur le plat de support en utilisant (3) des boulons de 3mm x de 12mm et des rondelles de freinage.

Placez les vis de (3) # de 8x3/8"sur les entretoises et alignez les fentes de support. Glissez le plat dedans et le fixez.

• Bringen Sie die Kamera zur Montageplatte mit (3) 3mm x 12mm den Schraubbolzen und den Federringen an. Setzen Sie (3) #

8x3/8"die Schrauben auf die Distanzscheiben und richten Sie die Befestigungsschlitze aus. Schieben Sie Platte innen und sichern

Sie.

• Instale a câmera à placa de montagem usando (3) os parafusos de 3mm x de 12mm e as arruelas de fechamento. Coloque os

parafusos de (3) # de 8x3/8"nos espaçadores e alinhe-os acima dos entalhes de montagem. Deslize a placa dentro e fixe-a.

• Installi la macchina fotografica al giunto di supporto usando (3) i bulloni di 12mm x di 3mm e le ranelle di bloccaggio. Disponga

le viti di 8x3/8"# di (3) sui distanziatori ed allinei le scanalature di montaggio. Faccia scorrere la piastra dentro e fissi.

Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3)

#8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure.

• Instale la cámara fotográfica a la placa de montaje con (2) los tornillos #10 y las arandelas de cerradura proporcionadas. Coloque los

tornillos de (3) del # 8x3/8"en los espaciadores y alinee las ranuras de montaje. Resbale en la placa y la cámara fotográfica entonces

seguras.

• Installez l'appareil-photo sur le plat de support avec (2) les vis #10 et les rondelles de freinage fournies. Placez les vis de (3) # de 8x3/8"

sur les entretoises et alignez les fentes de support. Glissez du plat et de l'appareil-photo puis bloqués.

• Bringen Sie die Kamera zur Montageplatte mit (2) den bereitgestellten Schrauben #10 und Federringen an. Setzen Sie (3) # 8x3/8"die

Schrauben auf die Distanzscheiben und richten Sie die Befestigungsschlitze aus. Schieben Sie auf die sichere Platte und Kamera dann.

• Instale a câmera à placa de montagem com (2) os parafusos #10 e as arruelas de fechamento fornecidas. Coloque os parafusos de

(3) # de 8x3/8"nos espaçadores e alinhe os entalhes de montagem. Deslize na placa e na câmera então seguras.

• Installi la macchina fotografica al giunto di supporto con (2) le viti #10 e le ranelle di bloccaggio fornite. Disponga le viti di 8x3/8"# di (3)

sui distanziatori ed allinei le scanalature di montaggio. Faccia scorrere sulla piastra e sulla macchina fotografica allora sicure.

2539 Mounting Plate

Mounting

Hole

Mounting

Hole

Axis 213

(26

) 1"

(52

) 2"

(13

) ½"

Captive

Screw

(3) #8x3/8”

Install the camera to the mounting plate with (4) #8 screws and lock washers provided. Place (3)

#8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure.

• Instale la cámara fotográfica a la placa de montaje con (4) los tornillos #8 y las arandelas de cerradura proporcionadas. Coloque los

tornillos de (3) del # 8x3/8"en los espaciadores y alinee las ranuras de montaje. Resbale en la placa y la cámara fotográfica entonces

seguras.

• Installez l'appareil-photo sur le plat de support avec (4) les vis #8 et les rondelles de freinage fournies. Placez les vis de (3) # de 8x3/8"

sur les entretoises et alignez les fentes de support. Glissez du plat et de l'appareil-photo puis bloqués.

• Bringen Sie die Kamera zur Montageplatte mit (4) den bereitgestellten Schrauben #8 und Federringen an. Setzen Sie (3) # 8x3/8"die

Schrauben auf die Distanzscheiben und richten Sie die Befestigungsschlitze aus. Schieben Sie auf die sichere Platte und Kamera dann.

• Instale a câmera à placa de montagem com (4) os parafusos #8 e as arruelas de fechamento fornecidas. Coloque os parafusos de

(3) # de 8x3/8"nos espaçadores e alinhe os entalhes de montagem. Deslize na placa e na câmera então seguras.

• Installi la macchina fotografica al giunto di supporto con (4) le viti #8 e le ranelle di bloccaggio fornite. Disponga le viti di 8x3/8"# di (3)

sui distanziatori ed allinei le scanalature di montaggio. Faccia scorrere sulla piastra e sulla macchina fotografica allora sicure.

Axis 215

(26

) 1"

(52

) 2"

Captive

Screw

(3) #8x3/8”

(26

) 1"

MOUNTING HOLE

AXIS215-VL3026

MOUNTING HOLE

Axis 231D/232D

Use the (3) keyhole slots indicated above.

• Utilice (3) las ranuras del ojo de la cerradura indicadas

arriba.

• Employez (3) les fentes de trou de la serrure indiquées

ci-dessus.

• Benutzen Sie die (3) Schlüssellochschlitze, die oben

angezeigt werden.

• Use (3) os entalhes do buraco da fechadura indicados

acima.

• Usi (3) le scanalature del buco della serratura indicate

sopra.

Mounting

Hole

Mounting

Hole

Mounting Hole

Tab

Loosen

Screw

AXIS 231-232D

Loosen the screw to the right of the tab by

approximately (5) turns.

• Afloje el tornillo a la derecha de la lengüeta aproxi-

madamente (5) vueltas.

• Desserrez la vis à la droite de l'étiquette approxima-

tivement (5) aux tours.

• Lösen Sie die Schraube auf der rechten Seite des

Vorsprunges durch ungefähr (5) Umdrehungen.

• Afrouxe o parafuso à direita da aba aproximada-

mente (5) por voltas.

• Allenti la vite alla destra della linguetta circa (5) dalle

girate.

Captive

Screw

(3) #8 x 3/8”

Locking Screw

Locking

Pins

Keyhole

Slot (3)

(13

) ½"

Position locking pins and locking screw over slots and turn clockwise; secure the screw. Place (3)

#8x3/8” screws on the spacers and line up mounting slots. Slide on plate and camera then secure.

• Coloque los pernos de fijación y el tornillo de fijación sobre ranuras y dé vuelta a la derecha; asegure el tornillo. Coloque los tornillos de

(3) del # 8x3/8"en los espaciadores y las ranuras de montaje de la formación. Resbale en la placa y la cámara fotográfica y asegure.

• Placez les chevilles de verrouillage et la vis de blocage au-dessus des fentes et tournez dans le sens des aiguilles d'une montre ; fixez la

vis. Placez les vis de (3) # de 8x3/8"sur les entretoises et les fentes de support de ligne. Glissez du plat et de l'appareil-photo et fixez.

• Bringen Sie Sicherungsstifte und Sicherungsschraube über Schlitzen in Position und drehen Sie nach rechts; sichern Sie die Schraube.

Setzen Sie (3) # 8x3/8"die Schrauben auf die Distanzscheiben und die Anordnungbefestigungsschlitze. Schieben Sie auf Platte und

Kamera und sichern Sie.

• Posicione os pinos travando e o parafuso travando sobre entalhes e gire-os no sentido horário; fixe o parafuso. Coloque os parafusos

de (3) # de 8x3/8"nos espaçadores e alinhe-os acima dos entalhes de montagem. Deslize na placa e na câmera e fixe.

• Posizioni i perni di bloccaggio e la vite di bloccaggio sopra le scanalature e giri in senso orario; fissi la vite. Disponga le viti di 8x3/8"# di

(3) sui distanziatori e sulle scanalature di montaggio dell'allineamento. Faccia scorrere sulla piastra e sulla macchina fotografica e fissi.

3mm

Screw

Power

Board

Connection

Module

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Quite a tablero de energía situado dentro de la cubierta. Una el módulo de la conexión según lo demostrado. Una

a esta asamblea a la cubierta usando (1) "arandela del tornillo 6-32x3/8 y de la estrella.

• Enlevez carte d'alimentation situé à l'intérieur du logement. Attachez le module de raccordement comme montré.

Attachez cette assemblée au logement en utilisant (1) la "vis 6-32x3/8 et tenez le premier rôle la rondelle.

• Entfernen Sie das Energie Brett, das innerhalb des Gehäuses befunden wird. Bringen Sie das Anschlußmodul an, wie

gezeigt. Bringen Sie diese Versammlung zum Gehäuse mit (1) "Schraube 6-32x3/8 und Sternunterlegscheibe an.

• Remova a placa de poder situada dentro da carcaça. Una o módulo da conexão como mostrado. Una este

conjunto à carcaça usando (1) do "arruela parafuso 6-32x3/8 e da estrela.

• Rimuova il bordo di alimentazione situato all'interno dell'alloggiamento. Fissi il modulo del collegamento come

indicato. Fissi questo complessivo all'alloggiamento usando (1) "rondella della vite 6-32x3/8 e della stella.

Remove the power board located inside the housing. Attach the connection module as shown.

Attach this assembly to the housing using (1) 6-32x3/8” screw and star washer.

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Termine el cableado a la cámara fotográfica. Una el montaje de la cámara fotográfica a la cubierta resbalando

(3) las ranuras abiertas del tornillo sobre los tornillos en la cubierta; apriete los sujetadores en el soporte.

• Accomplissez le câblage à l'appareil-photo. Attachez l'appareil-photo au logement en glissant (3) les fentes

ouvertes de vis au-dessus des vis dans le logement ; serrez les attaches sur la parenthèse.

• Führen Sie die Verdrahtung zur Kamera durch. Bringen Sie die Kamera zum Gehäuse an, indem Sie die (3) geöffne-

ten Schraube Schlitze über den Schrauben im Gehäuse schieben; ziehen Sie die Befestiger am Haltewinkel fest.

• Termine a fiação à câmera. Una o conjunto da câmera à carcaça deslizando (3) os entalhes abertos do parafuso

sobre os parafusos na carcaça; aperte os prendedores no suporte.

• Completi i collegamenti alla macchina fotografica. Fissi il complessivo della macchina fotografica all'alloggiamento

facendo scorrere (3) le scanalature aperte della vite sopra le viti nell'alloggiamento; stringa i fermi sulla staffa.

CONTROL

RJ45 Ethernet Connector

ALARMS

1 Alarm 1 Blue

2 Alarm 2 Violet

3 Alarm 3 Gray

4 Common White

POWER

1 Camera Power (24VAC) Red

2 Camera Power (24VAC) Orange

Captive

Screw

Open Screw

Slots

Cable

Ties

Complete the wiring to camera. Attach the camera assembly to the housing by sliding the (3)

open screw slots over the screws in the housing; tighten the fasteners on the bracket.

Axis 233D

Use the holes indicated above to mount

the camera.

• Utilice los agujeros indicados arriba para montar la

cámara fotográfica.

• Employez les trous indiqués ci-dessus pour monter

l'appareil-photo.

• Benutzen Sie die Bohrungen, die oben angezeigt

werden, um die Kamera anzubringen.

• Use os furos indicados acima para montar a

câmera.

• Usi i fori indicati sopra per montare la macchina

fotografica.

Mounting Hole

Disconnect the orange, red, and black wires. Remove the

power board in the housing by loosening screws on the

terminal block and the (4) machine screws.

• Desconecte los alambres anaranjados, rojos, y negros. Quite a tablero de

energía en la cubierta aflojando los tornillos en el bloque de terminales y (4)

los tornillos de la máquina.

• Débranchez les fils oranges, rouges, et noirs. Enlevez carte d'alimentation

dans le logement en desserrant des vis sur le TB et (4) les vis de machine.

• Trennen Sie die orange, roten und schwarzen Leitungen. Entfernen Sie das

Energie Brett im Gehäuse, indem Sie Schrauben am Klemmenblock und an

den (4) Maschine Schrauben lösen.

• Desconecte os fios alaranjados, vermelhos, e pretos. Remova a placa de

poder na carcaça afrouxando os parafusos no bloco terminal e (4) nos

parafusos da máquina.

• Stacchi i legare arancioni, rossi e neri. Rimuova il bordo di alimentazione

nell'alloggiamento allentando le viti sul blocchetto terminali e (4) sulle viti

della macchina.

Power

Board

Now remove the mounting bracket and attach (4) 1/2” spacers (located in the packet that came

with the housing) to the base bracket.

• Ahora quite el soporte de montaje y una (4) los espaciadores del 1/2"(situados en el paquete que vino con la cubierta)

al soporte bajo.

• Maintenant enlevez le support et attachez (4) les entretoises de 1/2"(situées dans le paquet qui est venu avec le

logement) à la parenthèse basse.

• Jetzt entfernen Sie die Schienenplatte und bringen Sie (4) die 1/2"Distanzscheiben (gelegen im Paket, das mit dem

Gehäuse kam), zum niedrigen Haltewinkel an.

• Agora remova o suporte de montagem e una (4) os espaçadores de 1/2"(situados no pacote que veio com a

carcaça) ao suporte baixo.

• Ora rimuova il supporto di attacco e fissi (4) i distanziatori di 1/2"(situati nel pacchetto che è venuto con

l'alloggiamento) alla staffa bassa.

Mounting

Bracket

½"

Quick Release

Plate

Base Bracket

Camera

Bracket

Additional

Spacers

Keyhole

Slots

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Monte el soporte de la cámara fotográfica del eje 233D y la placa rápida del lanzamiento usando los espaciadores

adicionales del paquete del hardware.

• Montez la parenthèse d'appareil-photo de l'axe 233D et le plat rapide de dégagement en utilisant les entretoises

additionnelles du paquet de matériel.

• Bringen Sie den Mittellinie 233D Kamerahaltewinkel und schnelle die Freigabeplatte mit den zusätzlichen Distanzs-

cheiben vom Kleinteilpaket an.

• Monte o suporte da câmera da linha central 233D e a placa rápida da liberação usando os espaçadores adicio-

nais do pacote da ferragem.

• Monti la staffa della macchina fotografica di asse 233D e la piastra rapida del rilascio usando i distanziatori supple-

mentari dal pacchetto dei fissaggi.

Mount the Axis 233D camera bracket and quick release plate using the additional spacers from

the hardware packet.

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Coloque la placa rápida del lanzamiento sobre el fondo de la cámara fotográfica. Alinee los tornillos de fijación de la cámara fotográfica y las

ranuras del ojo de la cerradura. Resbale la cámara fotográfica dentro de las ranuras del ojo de la cerradura hasta que los botones de fijación

golpean el extremo, y apriete el tornillo de pulgar.

• Placez le plat rapide de dégagement sur le fond de l'appareil-photo. Alignez les vis de blocage d'appareil-photo et les fentes de trou de la

serrure. Glissez l'appareil-photo dans les fentes de trou de la serrure jusqu'à ce que les boutons de fermeture frappent l'extrémité, et serrez la vis de

pouce.

• Setzen Sie schnelle Freigabeplatte auf der Unterseite der Kamera. Richten Sie die Sicherungsschrauben der Kamera und die Schlüssellochschlitze

aus. Schieben Sie Kamera in die Schlüssellochschlitze, bis die verriegelntasten das Ende schlagen, und ziehen Sie die Rändelschraube fest.

• Coloque a placa rápida da liberação no fundo da câmera. Alinhe os parafusos travando da câmera e os entalhes do buraco da fechadura.

Deslize a câmera nos entalhes do buraco da fechadura até que as teclas travando batam a extremidade, e aperte o parafuso de polegar.

• Disponga la piastra rapida del rilascio sulla parte inferiore della macchina fotografica. Allinei le viti di bloccaggio della macchina fotografica e le

scanalature del buco della serratura. Faccia scorrere la macchina fotografica nelle scanalature del buco della serratura fino a che i tasti di

bloccaggio non colpiscano l'estremità e stringa la vite di pollice.

Place quick release plate onto the bottom of the camera. Align the camera locking screws and the keyhole

slots. Slide camera into the keyhole slots until the locking buttons hit the end, and tighten the Thumb screw.

Keyhole Slots

Thumb Screw

Locking Screw

2539 Mounting Plate

Mounting

Hole

Mounting

Hole

Canon VB-C10R

Captive

Screw

(26

) 1"

(52

) 2"

(13

) ½"

Mount the camera to the 2539 plate using the provided hardware. Place (3) 8 x 32 x 3/8 Phillips

head screws on the top of the spacer as shown above. Slide plate in and secure.

• Monte la cámara fotográfica a la placa 2539 usando el hardware proporcionado. Coloque (3) 8 x 32 x 3/8 de los

tornillos principales Phillips en la tapa del espaciador según lo demostrado arriba. Resbale la placa adentro y

asegúrela.

• Montez l'appareil-photo au plat 2539 à l'aide du matériel fourni. Placez (3) 8 x 32 x 3/8 de vis principales Phillips sur le

dessus de l'entretoise comme montré ci-dessus. Glissez le plat dedans et le fixez.

• Bringen Sie die Kamera zur Platte 2539 mit den zur Verfügung gestellten Kleinteilen an. Setzen Sie (3) 8 x 32 x 3/8 Kreuz-

kopfhauptschrauben auf die Oberseite der Distanzscheibe, wie oben gezeigt. Schieben Sie Platte innen und sichern Sie.

• Monte a câmera à placa 2539 usando a ferragem fornecida. Coloque (3) 8 x 32 x 3/8 dos parafusos principais Phillips

no alto do espaçador como mostrado acima. Deslize a placa dentro e fixe-a.

• Monti la macchina fotografica alla piastra 2539 per mezzo dei fissaggi forniti. Disponga (3) 8 x 32 x 3/8 delle viti cape

"phillips" sulla parte superiore del distanziatore come indicato sopra. Faccia scorrere la piastra dentro e fissi.

2539 Mounting Plate

Mounting

Hole

Mounting

Hole

Canon VB-C50IR

Captive

Screw

(26

) 1"

(52

) 2"

(13

) ½"

Mount the camera to the 2539 plate using the provided hardware. Place (3) 8 x 32 x 3/8

Phillips head screws on the top of the spacer as shown above. Slide plate in and secure.