ZyXEL nwa1100-n Guida Rapida

www.zyxel.com

Quick Start Guide

NWA1100-N

802.11b/g/n PoE Access

Point

Firmware Version 1.00

Edition 1, 3/2011

DEFAULT LOGIN DETAILS

IP Address http://192.168.1.2

Username admin

Password 1234

CONTENTS

ENGLISH 3

DEUTSCH 15

ESPAÑOL 29

FRANÇAIS 42

ITALIANO 56

РУССКИЙ 70

SVENSKA 84

简体中文

96

繁體中文

108

2011 ZyXEL Communications Corporation

C

2

Panels

3

Overview

This Quick Start Guide shows how to set up and configure the

NWA1100-N (marked Z in the figure) to allow wireless clients to securely

access your wired network. See your User’s Guide for more information.

You may need your Internet access information.

To set up your wireless network you need to:

• Connect the Hardware

• Access the Web Configurator

• Configure the NWA1100-N

• Install the Hardware

• Set Up Power over Ethernet (Optional)

ENGLISH

44

Connect the Hardware

1. Using the Ethernet cable, connect the ETHERNET port to a computer

for initial configuration.

2. Connect the POWER

12VDC socket to a power source using only the

included power adaptor.

Connect the NWA1100-N’s ETHERNET port to an Ethernet jack with network

access after you have completed the initial configuration.

1

3

2

5

LEDs

•The SYS LED blinks red, then turns steady green when the power is

connected.

• One of the LEDs by the ETHERNET port turns on if the port is

properly connected, and blinks when there is traffic. The yellow light

shines if the connection is at 1000 Mbps. The green light shines if

the connection is at 10/100Mbps.

#If neither LED near the ETHERNET port turns on, check the cable

connections to the port. Ensure your computer’s network card is working

properly.

Access the Web Configurator

Internet Explorer 6.0 and later versions, with JavaScript enabled, or Mozilla Firefox

3 and later versions or Safari 2.0 and later versions.

Set Up Your Computer’s IP Address

Note down your computer’s current IP settings before you change them.

66

First, set your computer to use a static IP address in the 192.168.1.3 -

192.168.1.254 range with a subnet mask of 255.255.255.0. This ensures

that your computer can communicate with your NWA1100-N. See your

User’s Guide for information on setting up your computer’s IP address.

Log Into the Web Configurator

Even though you can connect to the NWA1100-N wirelessly, it is recommended

that you connect your computer to the ETHERNET port for initial configuration.

1. Launch your web browser. Enter

192.168.1.2 (the NWA1100-N’s

default IP address) as the

address.

#If you cannot access the Web configurator, make sure the IP addresses and

subnet masks of the NWA1100-N and the computer are in the same IP

address range.

2. Enter admin (the default

username) in the Username field

and 1234 (the default password) in

the Password field. Click Login.

3. Change the login password by

entering a new password and

clicking Apply. Be sure to record

the new password and keep it in a

safe place.

#If you change the password and then forget it, you will need to reset the

NWA1100-N. Refer to the User’s Guide for how to use the RESET button.

7

Configure the NWA1100-N

Configure System Settings

1. Click SYSTEM in the navigation panel.

2. The SYSTEM > General screen appears.

• System Name is for identifying the NWA1100-N on your network.

Choose a distinctive name, or leave this at its default.

4. The STATUS screen appears.

88

• You can configure the Ethernet port speed and duplex in the

Ethernet Data Rate field. If you are not sure, select Auto.

3. Click Apply.

Configure Wireless Settings

1. Click WIRELESS in the navigation panel. The Wireless Settings

screen displays. Configure the basic settings for your wireless

network.

The wireless stations and the NWA1100-N must use the same SSID, channel ID

and encryption settings for wireless communication.

• Operation Mode: Ensure that Access Point mode is selected.

9

• Wireless Mode: Select the wireless standard you want your

network to use. If you are not sure which to select, select 802.11b/

g/n.

• SSID Profile: Select the SSID profile you want to configure for

network access from the drop-down list box.

• Channel: Select the wireless channel you want your network to

use.

• Channel Width: Select the channel bandwidth you want to use. If

you are not sure, select 20/40 MHz.

2. Click Apply to save your settings.

3. Click the SSID tab. If you want to configure advanced settings of an

SSID profile (such as change the profile name, SSID, or security),

select it and click Edit.

1010

4. Click the Security tab. Select the profile you want to configure and

click Edit.

5. The edit screen of the selected security profile appears. If you don’t

configure wireless security, anyone can access your network.

• This is where you can enter the security settings for your wireless

network. The fields you fill in differ according to the type of security

you select in the Security Mode field. Select None if you do not

wish to use wireless security.

• This example uses WPA2-PSK security, in which all wireless clients

must use the same pre-shared key to join the network.

• Ensure that all your wireless clients support the type of security you

set. Click Apply when you have finished.

#If the wireless clients cannot communicate with the network, ensure that the

clients and the NWA1100-N are using the same wireless security settings.

11

Configure IP Settings

1. You need to set your NWA1100-N’s IP address to be in the same

subnet as your network. Click IP in the navigation panel.

• Select Obtain IP Address Automatically if you want to have a

DHCP server on your network assign an IP address to the

NWA1100-N.

• If you have a specific IP address to use, select Use Fixed IP

Address and enter it along with the subnet mask and gateway IP

address.

• If your ISP provided specific DNS (Domain Name System)

settings, enter them in the System DNS Servers section.

Otherwise, leave these fields at their defaults.

• Click Apply. The NWA1100-N now uses the new IP settings; you

can no longer connect to the NWA1100-N using the default IP

address.

If you change the NWA1100-N’s IP address, you must use the new IP address

when you next access the web configurator. If you select Obtain IP Address

Automatically, check your DHCP server to determine the IP address it assigns to

the NWA1100-N. Refer to your DHCP server’s documentation for more information.

1212

2. If you changed your computer’s IP address, return it to its previous

setting.

3. Change the wireless settings in the wireless stations to match those

of the NWA1100-N, if necessary. Refer to your wireless adapter’s

documentation.

The NWA1100-N is now ready to connect to your switch or router.

You can do this now, or once you have attached the antennas and

mounted the NWA1100-N.

#If the NWA1100-N cannot communicate with the network, ensure that the

NWA1100-N is using an IP address on the same subnet as the switch / router.

Install the Hardware

Attaching Antennas

Hardware Mounting

In general, the best location for the access point is at the center of your

intended wireless coverage area. For better performance, mount the

NWA1100-N high up in an area that is free of obstructions.

Wall-mounting

Do the following to attach your NWA1100-N to a wall.

Screw the antennas clockwise onto the

antenna connectors on the sides of your

NWA1100-N. The antennas should be

perpendicular to the ground and parallel to

each other.

Make sure the antennas are securely

screwed onto the antenna connectors.

13

1. Screw the two screws provided with your NWA1100-N into the wall

60mm apart (see the figure in step 3). Use screws with 6mm ~ 8mm

(0.24" ~ 0.31") wide heads. Do not screw the screws all the way in to

the wall; leave a small gap between the head of the screw and the

wall.

The gap must be big enough for the screw heads to slide into the

screw slots and the connection cables to run down the back of the

NWA1100-N.

Make sure the screws are securely fixed to the wall and strong enough to hold the

weight of the NWA1100-N with the connection cables.

2. Adjust the cables.

Run the connection cables down the back of the NWA1100-N as

shown in the following figure.

OR:

Run the connection cables upward and along the edge of the ceiling.

3. Align the holes on the back of the NWA1100-N with the screws on the

wall. Hang the NWA1100-N on the screws.

6

0

m

1414

Set Up Power over Ethernet (Optional)

Power over Ethernet (PoE) is the ability to provide power to your

NWA1100-N via an 8-pin CAT 5 Ethernet cable, eliminating the need for

a nearby power source.

A PoE injector (not included) is also needed to supply the Ethernet cable

with power. This feature allows increased flexibility in the location of your

NWA1100-N.

In the following figure, Z is your NWA1100-N, A is the CAT 5 Ethernet

cable, B is the PoE injector and C is the power cable.

For more information, please refer to the User’s Guide on the provided CD or at the

www.zyxel.com download library.

Was this guide helpful? Send your comments to [email protected]

Procedure to View a Product’s Certification(s)

1. Go to www.zyxel.com.

2. Select your product from the drop-down list box on the ZyXEL

home page to go to that product's page.

3. Select the certification you wish to view from this page.

15

Übersicht

In dieser Kurzanleitung erfahren Sie, wie das NWA1100-N (im Beispiel

unten mit einem Z gekennzeichnet) installiert und konfiguriert wird, damit

Wireless-Clients sicher auf Ihr kabelgebundenes Netzwerk zugreifen

können. Weitere Informationen finden Sie im Benutzerhandbuch.

Halten Sie die Daten für Ihren Internetzugang bereit.

Um das Drahtlosnetzwerk einzurichten, müssen Sie:

• Anschließen der Hardware

• Zugreifen auf den Web-Konfigurator

• Konfigurieren des NWA1100-Ns

• Installieren der Hardware

• Power-over-Ethernet (PoE) Einrichten (Optional)

DEUTSCH

1616

Anschließen der Hardware

1. Verbinden Sie für die Erstkonfiguration den ETHERNET-Anschluss

mit dem grauen Ethernet-Kabel mit dem Computer.

2. Verbinden Sie die 12VDC-Netzanschlussbuchse POWER des Geräts

mit dem mitgelieferten Netzadapter mit dem Stromnetz.

Nachdem Sie die Erstkonfiguration durchgeführt haben, verbinden Sie den

ETHERNET-Anschluss des NWA1100-Ns mit einem Ethernetanschluss mit

Netzwerkverbindung.

1

3

2

17

LED-Anzeigen

• Die LED-Anzeige SYS blinkt zunächst rot und beginnt grün zu

leuchten, sobald das Gerät mit Strom versorgt wird.

• Eine der LEDs am ETHERNET-Port beginnt zu leuchten, wenn der

Anschluss richtig verbunden ist. Bei Datenverkehr blinkt sie. Die

gelbe LED leuchtet, bei einer 1000-Mbps-Verbindung. Die grüne

LED leuchtet, bei einer 10/100-Mbps-Verbindung.

#Wenn keine der LEDs am ETHERNET-Port leuchtet, prüfen Sie die

Kabelverbindungen am Anschluss. Stellen Sie sicher, dass die Netzwerkkarte

des Computers installiert ist und einwandfrei funktioniert.

Zugreifen auf den Web-Konfigurator

Internet Explorer 6.0 und neuere Versionen mit aktiviertem JavaScript, Mozilla

Firefox 3 und neuere Versionen und Safari 2.0 und neuere Versionen.

Einrichten der IP-Adresse des Computers

Notieren Sie sich die aktuellen IP-Einstellungen des Computers, bevor Sie sie

ändern.

1818

Richten Sie den Computer zunächst so ein, dass er eine statische

Adresse im Bereich 192.168.1.3 bis 192.168.1.254 mit der Subnetz-

Maske 255.255.255.0 verwendet. Nur auf diese Weise kann Ihr

Computer mit dem NWA1100-N kommunizieren. Informationen zum

Einrichten der IP-Adresse des Computers finden Sie im

Benutzerhandbuch.

Anmelden beim Web-Konfigurator

Auch wenn Sie eine drahtlose Verbindung zum NWA1100-N herstellen können,

wird empfohlen, das Gerät für die Erstkonfiguration über den ETHERNET-

Anschluss an den Computer anzuschließen.

1. Starten Sie Ihren Webbrowser.

Geben Sie als Adresse

192.168.1.2 (die Standard-IP-

Adresse des NWA1100-Ns) ein.

#Wenn Sie nicht auf den Web-Konfigurator zugreifen können, prüfen Sie, ob

die IP-Adressen und Subnetz-Masken des NWA1100-Ns und des

Computers im selben IP-Adressbereich liegen.

2. Geben Sie den admin

(Standardbenutzernamen) in das

Feld Username (Benutzername)

und das Standardkennwort 1234

(Kennwort) in das Feld Password

(Kennwort). Klicken Sie auf Login

(Anmelden).

3. Ändern Sie das Kennwort, indem

Sie ein neues Kennwort eingeben

und auf Apply (Übernehmen)

klicken. Notieren Sie sich das

neue Kennwort und bewahren Sie

die Notiz an einem sicheren Ort

auf.

19

Konfigurieren des NWA1100-Ns

Konfigurieren der Systemeinstellungen

1. Klicken Sie in der Navigationsleiste auf SYSTEM.

#Wenn Sie das neue Kennwort vergessen haben, muss das NWA1100-N

zurückgesetzt werden. Lesen Sie im Benutzerhandbuch nach, wie die

RESET-Taste verwendet wird.

4. Die STATUS (Startseite)

erscheint.

2020

2. Das Fenster SYSTEM > General (System > Allgemein) erscheint.

• Der System Name (Systemname) identifiziert das NWA1100-N in

Ihrem Netzwerk. Wählen Sie einen Namen oder belassen Sie

diesen als Standard.

• Im Feld Ethernet Data Rate (Ethernet-Datenrate) können Sie die

Geschwindigkeit des Ethernet-Ports und die Duplexfunktion

konfigurieren. Wenn Sie sich nicht sicher sind, wählen Sie Auto

(Automatisch).

3. Klicken Sie auf Apply (Übernehmen).

La pagina si sta caricando...

ZyXEL nwa1100-n Guida Rapida

ZyXEL nwa1100-n Guida Rapida

in altre lingue

Documenti correlati

Altri documenti