ProLights SOLAR48Q Manuale utente
- Categoria
- Proiettori
- Tipo
- Manuale utente
USER MANUAL
MANUALE UTENTE
SOLAR48Q
OUTDOOR COMPACT WASHLIGHT
EN - IT
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the characteris-
tics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
REV. 02-11/19
1
SOLAR48Q
Packing content
• SOLAR48Q
• S48QFILTER60
• Power cable
• User manual
TABLE OF CONTENTS
Safety
General instructions
Warnings and installation precautions
1 Introduction
1. 1 Description
1. 2 Technical specications
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 DMX addressing
3. 5 DMX conguration
3. 6 Wireless settings
3. 7 Screen
3. 8 Fixture settings
3. 9 Information
3. 10 Master/Slave
3. 11 Eects mode
3. 12 Static mode
3. 13 Manual mode
3. 14 Connection of the DMX line
3. 15 Construction of the DMX termination
3. 16 DMX control
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Trouble shooting
2
2
3
3
5
6
7
7
8
9
10
10
10
11
11
12
12
12
12
13
13
14
17
17
SOLAR48Q
2
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• The connection to the main network of electric distribution must be carried out by a qualied electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
• Never use the xture under the following conditions:
- in places subject to vibrations or bumps;
- in places with an ambient temperature of over 50°C.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Do not dismantle or modify the xture.
• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
• If the unit is to be put out of operation denitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way dierent to the one described in this manual, it may suer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.
• When carrying out any work, always comply scrupulously with all the regulations (particularly regard-
ing safety) currently in force in the country in which the xture’s being used.
• The minimum distance between the xture and surrounding walls must be more than 50 cm and the
air vents at the housing must not be covered in any case.
• Keep any inammable material at a safe distance from the xture.
• The maximum temperature that can be reached on the external surface of the tting, in a thermally
steady state, is high. After power o, please cool down over 15 minutes.
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their eectiveness is impaired.
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• This product was designed and built strictly for the use indicated in this documentation. Any other use,
not expressly indicated here, could compromise the good condition/operation of the product and/or
be a source of danger.
• We decline any liability deriving from improper use of the product.
3
SOLAR48Q
- 1 - INTRODUCTION
1.1 DESCRIPTION
SOLAR48Q is a compact fan-free outdoor wash light featuring an outstanding brightness of 22'760
lumens. Equipped with 48x10 W RGBW full-colour LEDs all delivering superior colour mixing. Featuring a
slimline styling, multiple interchangeable optics through magnets, asymmetrical lters which combined,
make the SOLAR48Q an incredibly exible device for indoor and outdoor use. Whilst highly-powerful,
the SOLAR48Q is also completely silent.
1.2 TECHNICAL SPECIFICATIONS
LIGHT SOURCE
• Source: 48x10W RGBW / FC LEDs
• Luminous ux: 22'760lm
• Lux: (25°) 14'900lx @3 m full
• Lux: (25°) 5'364lx @5 m full
• Source life expectancy: > 50.000 h
OPTICS
• Beam angle: 25° - With included lter 45°
• Additional optics: 10° / 15° / 45° / 40° lter / 10x60° lter / 30x60° lter
• Other: magnetic lter included to achieve 45° (60° lter), barn door not included
COLOUR SYSTEM
• Colour mixing: RGBW / FC
• CTC: CTC control through independent DMX channel
• Colour wheel: virtual colour wheel with presets
• Macros: several pre-build macros with adjustable speed
DYNAMIC EFFECTS
• FX generator: section eect with 4 horizontal individually select and control sections
• Static colour mode: selection of static colour
• Manual colour mode: manual adjustment of colour
• Auto mode: built-in programs with execution speed adjustment
BODY
• Hardware on-board: magnetic lter frame with 45° lter
• Tilt angle: 0 - 150° manual
• Body: sturdy die-cast aluminium body conceived for long-time durability
• Body colour: black
CONTROL
• Protocols: DMX512, RDM, W-DMX
• DMX channels: 5 / 7 / 10 / 17 / 22channel
• W-DMX: included, wireless solution receiver
• RDM: RDM ready for xture remote monitor and settings
• Display: black OLED high resolution display
• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included
• Master/Slave: for synchronized operation of more units linked in a chain
SOLAR48Q
4
ELECTRONICS
• Dimmer: linear 0 ~ 100% electronic dimmer
• Dimmer curves: 4 dierent dimming curves available
• Strobe / shutter: 1 - 30 Hz, electronic
• Battery backup: battery backup for user operation without connecting to the main power
• Operating temperature: -20° ~ +45°
• Flicker: icker free frequency with adjustable PWM
• Selectable PWM: 600 ~ 25.000 Hz
ELECTRICAL
• Power consumption: 700
• Power supply: 100-240 V – 50/60 Hz
• Power consumption (at 230 V): 513W
• Power consumption (at 120 V): 541W
• Output (at 230 V): 4 units on a single power line
• Output (at 120 V): 2 units on a single power line
• Power factor: 0,95
PHYSICAL
• Cooling: natural cooling of the peculiar chassis and to absence of fans
• Sospension and xing: hanging bracket for oor positioning with "Quick-Lock" system
• Signal connection: Seetronic XLR 5p IN/OUT connectors
• Data connection: W-DMX receiver
• Power connection: Seetronic powerCON waterproof IN/OUT connectors
• IP rating: 65 for temporary outdoor application, not for xed installation
• Dimensions (WxHxD): 563x314x93mm
• Weight: 12,9kg
563
314
93
Technical drawing Fig.1
5
SOLAR48Q
1
2
3
4
5
7
8 9 106
1.3 OPERATING ELEMENTS AND CONNECTIONS
1. LED panel
2. MECHANICAL SYSTEM for individual position-
ing of Led panels
3. ANTENNA
4. POWER IN (PowerCON TRUE IN): for connection
to a socket (100-240V~/50-60Hz) via the sup-
plied mains cable.
5. DMX IN DMX IN (5-pole XLR): 1 = ground, 2 =
DMX-, 3 = DMX+, 4 N/C, 5 N/C.
Fig.2
6. HEATSINK
7. CONTROL PANEL with OLED display and 4 button
used to access the control panel functions and
manage them.
8. DMX OUT DMX OUT (5-pole XLR): 1 = ground, 2 =
DMX-, 3 = DMX+, 4 N/C, 5 N/C.
9. POWER OUT (PowerCON TRUE OUT): power out-
put for connection of multiple units in series
10. HEATSINK
SOLAR48Q
6
- 2 - INSTALLATION
2.1 MOUNTING
The SOLAR48Q may be set up on a solid and even surface. By means of the xing facilities of the baseplate,
the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For xing, stable
mounting clips are required. According to the gure, the bolts of the brackets are placed into the openings
provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that the unit
is rmly xed to avoid vibration and slipping while operating. The mounting place must be of sucient
stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any installa-
tion, always comply scrupulously with all the regulations (particularly regarding safety) currently in force
in the country in which the xture’s being used. Always additionally secure the projector with the safety
rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum
fall of the projector will be 20 cm.
Fig.3
CLAMP
SAFETY
CABLE
QUICK LOCK
OMEGA BRACKETS
not included
7
SOLAR48Q
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240V~/50-60Hz). To switch o, disconnect the mains
plug from the socket. For a more convenient operation it is recommended to connect the unit to a socket
which can be switched on and o via light switch.
3.2 BASIC
The SOLAR48Q has a OLED display and 4 button used to access the control panel functions and manage
them (g.4).
Fig.4
MENU
ENTER UP DOWN
To enter in the main
menù or to return to the
top level
Conrms the displayed
value, or activates the
displayed function, or
enters the successive
menu
Increases the value
displayed or passes to
the previous item in a
menu
Decreases the value
displayed or passes to
the next item in the
menu
SOLAR48Q
8
3.3 MENU STRUCTURE
MENU
1 CONNECT
ð
DMX Address
ð
Value (1-512)
DMX Mode
ð
5Ch
7Ch
10Ch
17Ch
22Ch
Wireless Setting
ð
Receive O/On
ð
O
On
Receive Reset
ð
No
Yes
Wireless To DMX
ð
No
Yes
2 SETUP
ð
Screen
ð
Back Light
ð
On
10s
20s
30s
Flip Display
ð
No
Yes
Key Lock
ð
No
Yes
3 ADVANCED
ð
Full On
ð
HB Mode
Studio Mode
Dimmer Mode
ð
O
Dimmer1
Dimmer2
Dimmer3
White Balance
ð
O
Adjust
ð
Red
Green
Blue
White
ð
<125-255>
LED Frequency
ð
600Hz
1200Hz
2000Hz
4000Hz
6000Hz
25kHZ
Factory Reload
ð
No
Yes
4 INFORMATION
ð
Fixture Hours
ð
0-9999
Version
ð
V1.0
UID
ð
<15D00232 ****>
5 STAND ALONE
ð
Master/Slave
ð
Master
Slave
Eects
ð
Eect 1
……
Eect 9
ð
<1-100>
9
SOLAR48Q
3.4 DMX ADDRESSING
To set DMX addressing follow the instructions below:
• Press the MENU button to enter the menu mode.
• Use the buttons UP/DOWN to select Connect. Press the ENTER button to conrm.
• Press the UP/DOWN buttons to select DMX Address. Press the ENTER button to conrm.
• Press the UP/DOWN buttons to select the desired value 001-512. Press the ENTER button to conrm.
• Press repeatedly the MENU button to return the menu mode.
To able to operate the SOLAR48Q with a light controller, adjust the DMX start address for the rst a
DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX
channel, adjust the start address 33 on the SOLAR48Q. The other functions of the light eect panel are
then automatically assigned to the following addresses.
Several units may be interconnected; follow the instructions below:
1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.
2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units
are connected in a chain.
Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the
units. For longer cable runs we suggest a terminator at the last xture (see page 16).
Number of
DMX chan-
nels
Start address
(example)
DMX Address
occupied
Next possible start
address for unit No. 1
Next possible start
address for unit No. 2
Next possible start
address for unit No. 3
5 33 33-37 38 43 48
7 33 33-39 40 47 54
10 33 33-42 43 53 63
17 33 33-49 50 67 84
22 33 33-54 55 77 99
ð
Static
ð
R
G
B
W
GB
RB
RG
RGB
RW
GW
BW
RGW
RBW
GBW
RGBW
Manual color
ð
Red
ð
<000-255>
SOLAR48Q
10
Fig.5 - Example of a DMX 5-channel conguration
DMX Address:53DMX Address: 43DMX Address: 38 DMX Address: 48
3.5 DMX CONFIGURATION
The SOLAR48Q has 5 DMX channels congurations selectable through the control panel.
• Press the MENU button to enter the menu mode.
• Use the UP/DOWN buttons to select the Connect. Press the button ENTER to conrm.
• Press the UP/DOWN buttons to select the DMX mode. Then press the button ENTER to conrm.
• Press the buttons UP/DOWN to select the desired conguration 5CH, 7CH, 10CH, 17CH, 22CH; then press the
button ENTER to save.
• Press repeatedly the button MENU to return the menu mode.
The tables on page 14, 15 and 16 indicate the operating mode and DMX value. The SOLAR48Q is equipped
with 5-pole XLR connections.
3.6 WIRELESS SETTINGS
• To enter the Wireless mode press the MENU button until the display shows Connect, then select Wireless
using the ENTER button.
• Select the Wireless Receive function using the UP/DOWN buttons, then press the ENTER button.
• To activate the Wireless Receive function, use the UP/DOWN buttons and select the On option.
• Press the ENTER button to conrm the selection.
• Press the MENU button to go back or wait a few seconds to exit the setup menu.
NOTE - Once you have performed these steps, you must synchronize with any WiFi unit with which you
want to communicate by pressing the sync button on it. At this point connect the DMX console to the
WiFi unit to open the communication with the SOLAR48Q.
• To reset the unit, select the Receive Reset function using the UP/DOWN buttons, press the ENTER button
until the display shows Connect, then select Receive Reset using the UP/DOWN buttons, then press the
ENTER button.
• To activate the mode use the UP / DOWN keys and select the Yes option.
• Press the ENTER button to conrm the selection.
• Press the MENU button to go back or wait a few seconds to exit the setup menu.
• To activate the Wireless to DMX function, use the UP / DOWN buttons to press the ENTER button until the
display shows Connect, then select Wireless to DMX, then press the ENTER button.
• To activate the mode use the UP/DOWN buttons and select the Yes option.
• Press the MENU button to go back or wait a few seconds to exit the setup menu.
3.7 SCREEN
It is possible to modify the following parameters, related to the display, following the same procedure:
. . . . . . . . . . . .
DMX512 Controller
11
SOLAR48Q
• Press the MENU button to access the main menu.
• Press the UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button ac-
cess the next menu.
• Press the UP/DOWN button to select Screen and press the ENTER button to proceed.
• Select the proposed option with the UP/DOWN button and press the ENTER button to conrm.
- Backlight - Auto O display backlight. This function allows you to switch o automatically the back-
lighting of the display after a certain time which can be set using the directional keys. To have the
display always on select On or set a value between those shown (10s, 20s, 30s) to turn o the display
once the chosen time has elapsed, after exiting the menu.
- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better
view of the display when the unit is hanging upside down. Select Yes to activate the function, No to
deactivate it.
- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-
pering with the settings. If this function is activated, the keys are locked automatically. To disable or
temporarily disable or disable the key lock function, press the keys in the following order to regain
access to the menu commands: UP, DOWN, UP, DOWN, ENTER. Select Yes to activate the function or
No to deactivate it.
• Press the MENU key repeatedly to exit the menu and to save the changes made.
3.8 FIXTURE SETTINGS
You can change the parameters for the device by following these steps:
• Press the MENU button to enter the menu mode.
• Use the UP/DOWN buttons to select the Advanced. Press the button ENTER to conrm.
• Press the UP/DOWN buttons to select the desired option and press the ENTER button to conrm:
- Full On Mode - Select the Full on Mode function to set the HB mode (High Brightness Mode, with the
maxinum value of the colors) or Studio mode with a automatic white calibration.
- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specic dimming curve.
Particularly when set:
• O: The increase in light intensity is linear.
• Dimmer 1: dimmer curve with low fade.
• Dimmer 2: dimmer curve with medium fade.
• Dimmer 3: dimmer curve with high fade.
- White Balance - White Balance function. Select the White Balance function to set the white balance by
changing the values (125-255) of the colors Red, Green, Blue and White.
- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz - 25 KHz using the UP/
DOWN and press on ENTER to conrm the selection.
- Factory Reload - To reset the unit. Select Yes or No and select ENTER to conrm.
• Press repeatedly the MENU button to return the menu mode.
3.9 INFORMATION
To view all the information on the device, proceed as follows:
• Press the MENU button to access the main menu. Press the UP/DOWN button to select Information, then
press the ENTER button to access the next menu.
• Press the UP/DOWN button to scroll through the menu, then select one of the following information-
and press the ENTER button to display it.
- Fixture Time - To view the operating time of the projector.
- Software Version - To view the rmware version will show on the display.
- UID - To view the identication ID for the RDM control.
SOLAR48Q
12
• Press repeatedly the MENU button to return the menu mode.
3.10 MASTER/SLAVE MODE
This mode will allow you to link up the units together without a controller. Choose a unit to function as the
Master. The unit must be the rst unit in line; other units will work as slave.
• Press the MENU button so many times until the display shows Stand Alone, then press ENTER.
• Select Master/Slave, then press the ENTER button.
• Using UP/DOWN, select the desired mode and then press the ENTER button.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the
units. For longer cable runs we suggest a terminator at the last xture (see page 13).
• Set the slaves to the same DMX modes.
NOTE: the unit, set in Static or Eect mode, always appears to be Master.
3.11 EFFECTS MODE
This xture has a built-in automatic program. To access this, please see the below instructions:
• To enter the Eects mode, press the MENU button to access the menu.
• Throught the UP/DOWN button select Stand Alone, then select Eect. Press ENTER to conrm
• Use UP/DOWN to select the desired program Eect 1, ..., Eect 9, then press ENTER to conrm.
• Set the value (1 - 100), through UP/DOWN, then press ENTER to conrm.
NOTE: after selecting the described mode, the unit will be Master.
3.12 STATIC MODE
This xture has the ability to accept custom static color settings. Access these chases via the control panel
on the back of the xture.
• Press the MENU button to access the main menu. Press the UP/DOWN button to select Stand Alone, then
press the ENTER button to access the next menu.
• Select Static, then press the ENTER button.
• Select Fixed Color through the UP/DOWN buttons, then press ENTER.
• Set the colors R , G , B, W, GB, RB, RG, RGB, RW, GW, BW, RGW, RBW, GBW, RGBW through the UP/DOWN buttons,
then press ENTER.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
NOTE: after selecting the described mode, the unit will be Master.
3.13 MANUAL MODE
This mode allows to combine the colors red, green, blue and white (R, G, B, W).
• Press the MENU button to access the main menu. Press the UP/DOWN button to select Stand Alone, then
press the ENTER button to access the next menu.
• Select Static, then press the ENTER button.
• Select Manual Color through the UP/DOWN buttons, then press ENTER.
• Select the color R, G, B, W through the UP/DOWN buttons, then press ENTER.
• Using UP/DOWN buttons, select the desired color value 000 - 255.
• Press ENTER button to continue to the next color R, G, B,W.
• Continue until the desired mix is obtained.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
NOTE: after selecting the described mode, the unit will be Master.
13
SOLAR48Q
3.14 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-
ance and low capacity.
The following diagram shows the connection mode:
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would
cause faulty xture and controller operation.
Over long runs can be necessary to insert a DMX level matching amplier.
For those connections the use of balanced microphone cable is not recommended because it cannot
transmit control DMX data reliably.
• Connect the controller DMX input to the DMX output of the rst unit.
• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input
of the following unit until all the units are connected in chain.
• When the signal cable has to run longer distance is recommended to insert a DMX termination on the
last unit.
3.15 CONSTRUCTION OF THE DMX TERMINATION
The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-
es the end of the line: under certain conditions and with certain cable lengths, this could cause them to
cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR
connector, as shown in gure.
Fig.6
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Pin4 : N/C
Pin5 : N/C
Fig.7
Example:
5 pin XLR connector
SOLAR48Q
14
3.16 DMX CONTROL
5 CHANNELS
MODE
FUNCTION DMX
Value
5 Ch
1
RED
0~100% 000 - 255
2
GREEN
0~100% 000 - 255
3
BLUE
0~100% 000 - 255
4
WHITE
0~100% 000 - 255
5
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode o
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000-051
052-101
102-152
153-203
204-255
10 CHANNELS
MODE
FUNCTION DMX
Value
10 Ch
1
DIMMER
0~100% 000 - 255
2
RED
0~100% 000 - 255
3
GREEN
0~100% 000 - 255
4
BLUE
0~100% 000 - 255
5
WHITE
0~100% 000 - 255
6
STROBE
No function
Strobe Slow to Fast
000 - 010
011 - 255
7
COLOR MACRO
No Function
R 100%, G 0~100%, B 0 %
R 100%~0 %, G 100%, B 0 %
R 0 %, G 100%, B 0~100%
R 0 %, G 100~0 %, B 100%
R 0~100%, G 0 %, B 100%
R 100%, G 0 %, B 100~0 %
R 100%, G 0~100%, B 0~100%
R 100~0 %, G 100~0 %, B 100%
R 100%, G 100%, B 100%, W 100%
2800k
3000k
3200k
4000k
5600k
6000k
6500k
7000k
8000k
9000k
10000k
000 - 010
011 - 030
031 - 050
051 - 070
071 - 090
091 - 110
111 - 130
131 - 150
151 - 170
171 - 200
201 - 205
206 - 210
211 - 215
216 - 220
221 - 225
226 - 230
231 - 235
236 - 240
241 - 245
246 - 250
251 - 255
7 CHANNELS
MODE
FUNCTION DMX
Value
7 Ch
1
DIMMER
0~100% 000 - 255
2
RED
0~100% 000 - 255
3
GREEN
0~100% 000 - 255
4
BLUE
0~100% 000 - 255
5
WHITE
0~100% 000 - 255
6
STROBE
No function
Strobe Slow to Fast
000 - 010
011 - 255
7
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode o
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000-051
052-101
102-152
153-203
204-255
15
SOLAR48Q
10 CHANNELS
MODE
FUNCTION DMX
Value
10 Ch
8
EFFECTS
NO Function
Eect 1
Eect 2
Eect 3
Eect4
Eect5 (Eects1- 4)
Eect 6
Eect 7
Eect 8
Eect 9 (Eects6- 8)
000-010
011-037
038-064
065-091
092-118
119-145
146-172
173-199
200-226
227-255
9
EFFECTS SPEED
Eects speed slow to fast 000 - 255
10
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode o
Dimmer speed mode 1 (fast speed)
Dimmer speed mode 2 (middle speed)
Dimmer speed mode 3 (slow speed)
000 - 051
052 - 101
102 - 152
153 - 203
204 - 255
17 CHANNELS
MODE
FUNCTION DMX
Value
17 Ch
1
RED 1
0~100% 000 - 255
2
GREEN 1
0~100% 000 - 255
3
BLUE 1
0~100% 000 - 255
4
WHITE 1
0~100% 000 - 255
5
RED 2
0~100% 000 - 255
6
GREEN 2
0~100% 000 - 255
7
BLUE 2
0~100% 000 - 255
8
WHITE 2
0~100% 000 - 255
9
RED 3
0~100% 000 - 255
10
GREEN 3
0~100% 000 - 255
11
BLUE 3
0~100% 000 - 255
12
WHITE 3
0~100% 000 - 255
13
RED 4
0~100% 000 - 255
14
GREEN 4
0~100% 000 - 255
15
BLUE 4
0~100% 000 - 255
16
WHITE 4
0~100% 000 - 255
17
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode o
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000-051
052-101
102-152
153-203
204-255
SOLAR48Q
16
22 CHANNELS
MODE
FUNCTION DMX
Value
22 Ch
1
DIMMER
0~100% 000 - 255
2
STROBE 1
No function
Strobe Slow to Fast
000 - 010
011 - 255
3
STROBE 2
No function
Strobe Slow to Fast
000 - 010
011 - 255
4
STROBE 3
No function
Strobe Slow to Fast
000 - 010
011 - 255
5
STROBE 4
No function
Strobe Slow to Fast
000 - 010
011 - 255
6
RED 1
0~100% 000 - 255
7
GREEN 1
0~100% 000 - 255
8
BLUE 1
0~100% 000 - 255
9
WHITE 1
0~100% 000 - 255
10
RED 2
0~100% 000 - 255
11
GREEN 2
0~100% 000 - 255
12
BLUE 2
0~100% 000 - 255
13
WHITE 2
0~100% 000 - 255
14
RED 3
0~100% 000 - 255
15
GREEN 3
0~100% 000 - 255
16
BLUE 3
0~100% 000 - 255
17
WHITE 3
0~100% 000 - 255
22 CHANNELS
MODE
FUNCTION DMX
Value
22 Ch
18
RED 4
0~100% 000 - 255
19
GREEN 4
0~100% 000 - 255
20
BLUE 4
0~100% 000 - 255
21
WHITE 4
0~100% 000 - 255
22
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode o
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000-051
052-101
102-152
153-203
204-255
17
SOLAR48Q
- 4 - MAINTENANCE
4.1 MAINTENANCE AND CLEANING THE UNIT
• Make sure the area below the installation place is free from unwanted persons during setup.
• Switch o the unit, unplug the main cable and wait until the unit has cooled down.
• All screws used for installing the device and any of its parts should be tightly fastened and should not
be corroded.
• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any
deformation.
• When the lens is visibly damaged due to cracks or deep scratches, it must be replaced.
• The main cables must be in impeccable condition and should be replaced immediately even when a
small problem is detected.
• In order to protect the device from overheating the cooling fans (if any), and ventilation openings
should be cleaned monthly.
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts
subject to dust and grease deposits. The frequency with which the following operations are to be carried
out depends on various factors, such as the amount of the eects and the quality of the working environ-
ment (air humidity, presence of dust, salinity, etc.). Use a soft cloth dampened with any detergent liquid
for cleaning glass to remove the dirt from the reectors, from the lenses and lters.
It is recommended that the projector undergoes an annual service by a qualied technician for special
maintenance involving at least the following operations:
- General cleaning of internal parts..
- Restoring lubrication of all parts subject to friction, using lubricants specically.
- General visual check of the internal components, cabling, mechanical parts, etc.
- Electrical, photometric and functional checks; eventual repairs.
Warning: we strongly recommend internal cleaning to be carried out by qualied personnel!
4.2 TROUBLESHOOTING
Problems Possible causes Checks and remedies
Fixture does not light up
• No mains supply
• Dimmer fader set to 0
• All color faders set to 0
• Faulty LED
• Faulty LED board
• Check the power supply voltage
• Increase the value of the dimmer channels
• Increase the value of the color channels
• Replace the LED board
• Replace the LED board
General low light intensity
• Dirty lens assembly
• Misaligned lens assembly
• Clean the xture regularly
• Install lens assembly properly
Fixture does not power up
• No power
• Loose or damaged power cord
• Faulty internal power supply
• Check for power on power outlet
• Check power cord
• Replace internal power supply
Fixture does not respond to DMX
• Wrong DMX addressing
• Damaged DMX cables
• Bouncing signals
• Check control panel and unit addressing
• Check DMX cables
• Install terminator as suggested
Contact an authorized service center in case of technical problems or not reported in the table can not be
resolved by the procedure given in the table.
REV. 02-11/19
Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.
La riproduzione - anche parziale - per propri scopi commerciali è vietata.
Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in qualun-
que momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.
Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
ProLights SOLAR48Q Manuale utente
- Categoria
- Proiettori
- Tipo
- Manuale utente
in altre lingue
- English: ProLights SOLAR48Q User manual
Documenti correlati
-
ProLights IP65 160 W zoomable LED ellipsoidal Manuale utente
-
-
-
-
-
-
-
ProLights 150W IP65 rated full colour COB LED Par Manuale utente
-
-
