Toshiba Copier e-STUDIO281c Manuale utente

Categoria
Multifunzionali
Tipo
Manuale utente

Questo manuale è adatto anche per

SERVICE HANDBOOK
MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS
e-STUDIO281c/351c/451c
File No. SHE050003B0
R05032182700-TTEC
Ver02_2005-11
© 2005 TOSHIBA TEC CORPORATION
All rights reserved
GENERAL PRECAUTIONS REGARDING THE SERVICE FOR
e-STUDIO281c/351c/451c
The installation and service should be done by a qualified service
technician.
1) Transportation/Installation
- When transporting/installing the equipment, employ four persons and be sure to hold the posi-
tions as shown in the figure.
The equipment is quite heavy and weighs approximately 113 kg (249 lb), therefore pay full atten-
tion when handling it.
- Be sure not to hold the movable parts or units (e.g. the control panel, ADU or RADF) when trans-
porting the equipment.
- Be sure to use a dedicated outlet with AC 110 V / 13.2 A, 115 V or 127 V / 12 A, 220-240 V or 240
V / 8 A for its power source.
- The equipment must be grounded for safety.
- Select a suitable place for installation. Avoid excessive heat, high humidity, dust, vibration and
direct sunlight.
- Provide proper ventilation since the equipment emits a slight amount of ozone.
- To insure adequate working space for the copying operation, keep a minimum clearance of 80
cm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) on the rear.
- The equipment shall be installed near the socket outlet and shall be accessible.
- Be sure to fix and plug in the power cable securely after the installation so that no one trips over
it.
2) General Precautions at Service
- Be sure to turn the power OFF and unplug the power cable during service (except for the service
should be done with the power turned ON).
- Unplug the power cable and clean the area around the prongs of the plug and socket outlet once
a year or more. A fire may occur when dust lies on this area.
- When the parts are disassembled, reassembly is the reverse of disassembly unless otherwise
noted in this manual or other related documents. Be careful not to install small parts such as
screws, washers, pins, E-rings, star washers in the wrong places.
- Basically, the equipment should not be operated with any parts removed or disassembled.
- The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband
since the ICs on it may be damaged due to static electricity.
- Avoid expose to laser beam during service. This equipment uses a laser diode. Be sure not to
expose your eyes to the laser beam. Do not insert reflecting parts or tools such as a screwdriver
on the laser beam path. Remove all reflecting metals such as watches, rings, etc. before starting
service.
- Be sure not to touch high-temperature sections such as the exposure lamp, fuser unit, damp
heater and areas around them.
- Be sure not to touch high-voltage sections such as the chargers, transfer belt, 2nd transfer roller,
developer, IH control circuit, high-voltage transformer, exposure lamp control inverter, inverter for
the LCD backlight and power supply unit. Especially, the board of these components should not
be touched since the electric charge may remain in the capacitors, etc. on them even after the
power is turned OFF.
- Make sure that the equipment will not operate before touching potentially dangerous places (e.g.
rotating/operating sections such as gears, belts pulleys, fans and laser beam exit of the laser
optical unit).
- Be careful when removing the covers since there might be the parts with very sharp edges
underneath.
- When servicing the equipment with the power turned ON, be sure not to touch live sections and
rotating/operating sections. Avoid exposing your eyes to laser beam.
- Use designated jigs and tools.
- Use recommended measuring instruments or equivalents.
- Return the equipment to the original state and check the operation when the service is finished.
3) Important Service Parts for Safety
- The breaker, door switch, fuse, thermostat, thermofuse, thermistor, IC-RAMs including lithium
batteries, etc. are particularly important for safety. Be sure to handle/install them properly. If
these parts are short-circuited and their functions become ineffective, they may result in fatal
accidents such as burnout. Do not allow a short-circuit or do not use the parts not recommended
by Toshiba TEC Corporation.
4) Cautionary Labels
- During servicing, be sure to check the rating plate and cautionary labels such as “Unplug the
power cable during service”, “CAUTION. HOT”, “CAUTION. HIGH VOLTAGE”, “CAUTION.
LASER BEAM”, etc. to see if there is any dirt on their surface and if they are properly stuck to the
equipment.
Caution: Before using the wristband, unplug the power cable of the equipment and
make sure that there are no charged objects which are not insulated in the
vicinity.
5) Disposal of the Equipment, Supplies, Packing Materials, Used Batteries and IC-RAMs
- Regarding the recovery and disposal of the equipment, supplies, packing materials, used batter-
ies and IC-RAMs including lithium batteries, follow the relevant local regulations or rules.
Caution:
Dispose of used batteries and IC-RAMs including lithium batteries according to this manual.
Attention:
Se débarrasser de batteries et IC-RAMs usés y compris les batteries en lithium selon ce manuel.
Vorsicht:
Entsorgung der gebrauchten Batterien und IC-RAMs (inclusive der Lithium-Batterie) nach diesem Handbuch.
June 2005 © TOSHIBA TEC e-STUDIO281c/351c/451c CONTENTS
1
CONTENTS
1. SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES ......................................... 1-1
1.1 Specifications....................................................................................................................... 1-1
1.2 Accessories ......................................................................................................................... 1-7
1.3 Options ................................................................................................................................ 1-8
1.4 Supplies............................................................................................................................... 1-9
1.5 System List ........................................................................................................................ 1-10
2. ERROR CODE AND SELF-DIAGNOSTIC MODE........................................................ 2-1
2.1 Error Code List..................................................................................................................... 2-1
2.1.1 Jam........................................................................................................................... 2-1
2.1.2 Service call ...............................................................................................................2-7
2.1.3 Error in Internet FAX / Scanning Function.............................................................. 2-13
2.1.4 Printer function error............................................................................................... 2-21
2.2 Self-diagnosis Modes ........................................................................................................ 2-23
2.2.1 Input check (Test mode 03).................................................................................... 2-25
2.2.2 Output check (test mode 03) .................................................................................. 2-34
2.2.3 Test print mode (test mode 04) .............................................................................. 2-37
2.2.4 Adjustment mode (05) ............................................................................................ 2-38
2.2.5 Setting mode (08) ................................................................................................... 2-85
2.2.6 Pixel counter......................................................................................................... 2-198
2.2.7 Classification List of Adjustment Mode (05) / Setting Mode (08).......................... 2-208
3. ADJUSTMENT .............................................................................................................. 3-1
3.1 Adjustment Order (Image Related Adjustment)................................................................... 3-1
3.2 Adjustment of the Auto-Toner Sensor ................................................................................. 3-2
3.3 Performing Image Quality Control ....................................................................................... 3-5
3.4 Image Dimensional Adjustment........................................................................................... 3-6
3.4.1 General description .................................................................................................. 3-6
3.4.2 Paper alignment at the registration roller ................................................................. 3-8
3.4.3 Printer related adjustment ........................................................................................ 3-9
3.4.4 Scanner related adjustment ................................................................................... 3-14
3.5 Image Quality Adjustment (Copying Function) .................................................................. 3-21
3.5.1 Automatic gamma adjustment ................................................................................ 3-21
3.5.2 Color Deviation Adjustment.................................................................................... 3-22
3.5.3 Density adjustment................................................................................................. 3-28
3.5.4 Color balance adjustment....................................................................................... 3-29
3.5.5 Gamma balance adjustment .................................................................................. 3-30
3.5.6 Offsetting adjustment for background processing .................................................. 3-30
3.5.7 Judgment threshold for ACS .................................................................................. 3-31
3.5.8 Sharpness adjustment............................................................................................ 3-31
3.5.9 Setting range correction ......................................................................................... 3-32
3.5.10 Setting range correction (Adjustment of background peak) ................................... 3-32
3.5.11 Adjustment of smudged/faint text ........................................................................... 3-33
3.5.12 Adaptation to highlighter......................................................................................... 3-33
3.5.13 Beam level conversion setting................................................................................ 3-34
3.5.14 Maximum toner density adjustment to paper type.................................................. 3-34
3.5.15 Maximum text density adjustment .......................................................................... 3-35
3.5.16 Text/Photo reproduction level adjustment .............................................................. 3-35
3.5.17 Black reproduction switching at the Twin color copy mode.................................... 3-36
3.5.18 Background adjustment(Black Mode) .................................................................... 3-36
3.6 Image Quality Adjustment (Printing Function) ................................................................... 3-37
3.6.1 Automatic gamma adjustment ................................................................................ 3-37
3.6.2 Color deviation adjustment..................................................................................... 3-38
e-STUDIO281c/351c/451c CONTENTS June 2005 © TOSHIBA TEC
2
3.6.3 Gamma balance adjustment (Black Mode) ............................................................ 3-38
3.6.4 Color balance adjustment (Color Mode)................................................................. 3-39
3.6.5 Adjustment of smudged/faint text ........................................................................... 3-39
3.6.6 Upper limit value at Toner Saving Mode ................................................................ 3-40
3.6.7 Dot size adjustment in black printing...................................................................... 3-40
3.6.8 Maximum toner density adjustment to paper type.................................................. 3-40
3.6.9 Image processing: Gamma correction table all clearing......................................... 3-40
3.7 Image Quality Adjustment (Scanning Function) ................................................................ 3-41
3.7.1 Gamma balance adjustment .................................................................................. 3-41
3.7.2 Density adjustment (Black Mode)........................................................................... 3-42
3.7.3 Background adjustment (Gray Scale Mode) .......................................................... 3-43
3.7.4 Background adjustment (Color Mode).................................................................... 3-43
3.7.5 Judgment threshold for ACS .................................................................................. 3-44
3.7.6 Sharpness adjustment............................................................................................ 3-44
3.7.7 Setting range correction ......................................................................................... 3-45
3.7.8 Setting range correction (Adjustment of background peak) ................................... 3-45
3.7.9 Fine adjustment of black density ............................................................................ 3-46
3.7.10 RGB conversion method selection ......................................................................... 3-46
3.7.11 Reproduction ratio of primary scanning direction (black) ....................................... 3-47
3.7.12 Reproduction ratio of primary scanning direction (color) ........................................ 3-47
3.8 High-Voltage Transformer Setting ..................................................................................... 3-48
3.8.1 General description ................................................................................................ 3-48
3.8.2 Setting at the replacement of high-voltage transformer ......................................... 3-48
3.9 Adjustment of the Scanner Section ................................................................................... 3-49
3.9.1 Carriages ................................................................................................................ 3-49
3.9.2 Lens unit................................................................................................................. 3-53
3.10 Adjustment of the Paper Feeding System ......................................................................... 3-55
3.10.1 Sheet sideways deviation caused by paper feeding .............................................. 3-55
3.11 Adjustment of the Developer Unit...................................................................................... 3-57
3.11.1 Doctor-to-sleeve gap (black developer unit)........................................................... 3-57
3.11.2 Doctor-to-sleeve gap (color developer unit) ........................................................... 3-59
3.11.3 Black developer unit lift up/down timing adjustment............................................... 3-61
3.12 Adjustment of the RADF (MR-3018).................................................................................. 3-63
3.12.1 Adjustment of RADF Position................................................................................. 3-63
3.12.2 Adjustment of RADF Height ................................................................................... 3-68
3.12.3 Adjustment of Skew................................................................................................ 3-70
3.12.4 Adjustment of the Leading Edge Position .............................................................. 3-73
3.12.5 Adjustment of Horizontal Position .......................................................................... 3-74
3.12.6 Adjustment of Copy Ratio....................................................................................... 3-76
3.12.7 Adjustment of RADF Opening/Closing Sensor....................................................... 3-77
3.13 Adjustment of the Finisher (MJ-1022)................................................................................ 3-78
3.13.1 Adjusting the jogging plate width............................................................................ 3-78
3.13.2 Adjusting the angle of the jogging plate ................................................................. 3-80
3.13.3 Adjusting the overlap of the sensor flag ................................................................. 3-81
3.13.4 Adjusting the tension of the stack processing motor belt ....................................... 3-82
3.13.5 Releasing the stack tray guide lever fixing plate .................................................... 3-84
3.13.6 Adjustment of the upper tray angle ........................................................................ 3-85
3.13.7 DIP switch functions ............................................................................................... 3-87
3.14 Adjustment of the Finisher (MJ-1023/1024)....................................................................... 3-89
3.14.1 Adjusting the alignment position (Finisher unit)...................................................... 3-89
3.14.2 Adjusting the staple position (Finisher unit)............................................................ 3-90
3.14.3 Adjusting the folding position (Saddle stitcher unit)................................................ 3-91
3.14.4 Fine adjustment of binding/folding position (Saddle stitcher unit) .......................... 3-94
3.14.5 Sensor output adjustment (Puncher unit)............................................................... 3-94
3.14.6 Registering the number of punch holes (Puncher unit) .......................................... 3-95
June 2005 © TOSHIBA TEC e-STUDIO281c/351c/451c CONTENTS
3
4. PREVENTIVE MAINTENANCE (PM)............................................................................ 4-1
4.1 PM Support Mode................................................................................................................ 4-1
4.1.1 General description .................................................................................................. 4-1
4.1.2 Operational flow and operational screen.................................................................. 4-1
4.1.3 Work flow of parts replacement ................................................................................ 4-8
4.2 General Descriptions for PM Procedure.............................................................................. 4-9
4.3 Operational Items in Overhauling ...................................................................................... 4-10
4.4 Preventive Maintenance Checklist..................................................................................... 4-11
4.5 PM KIT............................................................................................................................... 4-28
4.6 Jig List ............................................................................................................................... 4-29
4.7 Grease List ........................................................................................................................ 4-30
4.8 Precautions for Storing and Handling Supplies ................................................................. 4-31
4.8.1 Precautions for storing TOSHIBA supplies ............................................................ 4-31
4.8.2 Checking and cleaning of photoconductive drum................................................... 4-31
4.8.3 Checking and cleaning of drum cleaning blade and transfer belt cleaning blade... 4-32
4.8.4 Handling of drum cleaner brush ............................................................................. 4-32
4.8.5 Handling of transfer belt ......................................................................................... 4-32
4.8.6 Checking and cleaning of fuser belt and pressure roller ........................................ 4-33
4.8.7 Checking and replacing the oil roller and cleaning roller........................................ 4-33
4.8.8 Checking and cleaning of discharge brush ............................................................ 4-34
5. TROUBLESHOOTING .................................................................................................. 5-1
5.1 Diagnosis and Prescription for Each Error Code ................................................................. 5-1
5.1.1 Paper transport jam (paper exit section) .................................................................. 5-1
5.1.2 Paper misfeeding ..................................................................................................... 5-3
5.1.3 Paper transport jam ................................................................................................ 5-10
5.1.4 Other paper jam ..................................................................................................... 5-18
5.1.5 Cover open jam ...................................................................................................... 5-20
5.1.6 RADF jam ............................................................................................................... 5-24
5.1.7 Finisher jam ............................................................................................................ 5-29
5.1.8 Drive system related service call ............................................................................ 5-43
5.1.9 Paper feeding system related service call.............................................................. 5-44
5.1.10 Scanning system related service call ..................................................................... 5-50
5.1.11 Fuser unit related service call................................................................................. 5-51
5.1.12 Communication related service call........................................................................ 5-54
5.1.13 RADF related service call....................................................................................... 5-55
5.1.14 Circuit related service call ...................................................................................... 5-55
5.1.15 Laser optical unit related service call ..................................................................... 5-57
5.1.16 Finisher related service call .................................................................................... 5-58
5.1.17 Image control related service call........................................................................... 5-69
5.1.18 Copy process related service call........................................................................... 5-72
5.1.19 Toner density control related service call ............................................................... 5-76
5.1.20 Other service call.................................................................................................... 5-80
5.1.21 Error in Internet FAX / Scanning Function.............................................................. 5-81
5.2 Troubleshooting for the Image........................................................................................... 5-95
5.3 Replacement of PC Boards and HDD ............................................................................. 5-127
5.3.1 Replacing HDD..................................................................................................... 5-127
5.3.2 Replacing SYS board ........................................................................................... 5-129
5.3.3 Replacing SLG board ........................................................................................... 5-130
5.3.4 Replacing or clearing NVRAM.............................................................................. 5-130
5.3.5 Cautions when Data overwrite kit (GP-1060) is installed .................................... 5-131
5.3.6 HDD information display....................................................................................... 5-132
5.4 Other errors ..................................................................................................................... 5-134
6. FIRMWARE UPDATING ............................................................................................... 6-1
6.1 Firmware Updating with Download Jig ................................................................................ 6-2
e-STUDIO281c/351c/451c CONTENTS June 2005 © TOSHIBA TEC
4
6.1.1 PWA-DWNLD-350-JIG2 (48 MB) ............................................................................. 6-4
6.1.2 Writing the data to the download jig (PWA-DWNLD-350-JIG) ............................... 6-13
6.1.3 K-PWA-DLM-320.................................................................................................... 6-15
6.2 Firmware Updating with USB Storage Device................................................................... 6-26
6.2.1 Appendix ................................................................................................................ 6-41
7. POWER SUPPLY UNIT ................................................................................................ 7-1
7.1 Output Channel ................................................................................................................... 7-1
7.2 Fuse..................................................................................................................................... 7-3
7.3 Configuration of Power Supply Unit..................................................................................... 7-4
8. REMOTE SERVICE....................................................................................................... 8-1
8.1 Auto Supply Order ............................................................................................................... 8-1
8.1.1 Outline ...................................................................................................................... 8-1
8.1.2 Setting Item .............................................................................................................. 8-2
8.1.3 Setting procedure ..................................................................................................... 8-4
8.1.4 Order Sheet Format ............................................................................................... 8-11
8.2 Service Notification............................................................................................................ 8-13
8.2.1 Outline ....................................................................................................................8-13
8.2.2 Setting ....................................................................................................................8-13
8.2.3 Items to be notified ................................................................................................. 8-19
9. DATA CLONING with USB STORAGE DEVICE ......................................................... 9-1
10. WIRE HARNESS CONNECTION DIAGRAMS ........................................................... 10-1
10.1 AC Wire Harness............................................................................................................... 10-1
10.2 DC Wire Harness....................................................................................................... Appendix
10.3 Electric Parts Layout.................................................................................................. Appendix
05/11
1
2
3
4
5
6
7
8
9
10
1. SPECIFICATIONS/ACCESSORIES/OPTIONS/
SUPPLIES
2. ERROR CODE AND SELF-DIAGNOSTIC
MODE
3. ADJUSTMENT
4. PREVENTIVE MAINTENANCE (PM)
5. TROUBLESHOOTING
6. FIRMWARE UPDATING
7. POWER SUPPLY UNIT
8. REMOTE SERVICE
9. DATA CLONING with USB STORAGE DEVICE
10. WIRE HARNESS CONNECTION DIAGRAMS
05/11
June 2005 © TOSHIBA TEC e-STUDIO281c/351c/451c SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES
1 - 1
1
1. SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES
1.1 Specifications
yCopy process .......................... Indirect electrophotographic process (dry)
yType......................................... Desktop type (Console type: when optional Paper Feed Pedestal
(PFP) or optional Large Capacity Feeder (LCF) is installed.)
yOriginal table ........................... Fixed type (the left rear corner used as guide to place originals)
yAccepted originals ................... Original type: Sheets, books and 3-dimensional objects
Note that when the optional Reversing Automatic Document Feeder is
used, carbon, bounded or stapled originals cannot be accepted, and
paper type of the original should be 35-157g/m
2
(9.3 lb. Bond -58 lb.
Cover) for single-sided copy and 50-157 g/m
2
(13.3 lb. Bond -58 lb.
Cover) for double-sided copy.
Maximum size: A3/LD
Copy speed (Copies/min.)
e-STUDIO281c
e-STUDIO351c
e-STUDIO451c
* "-" means "Not acceptable".
* When originals are manually placed for single-sided, continuous copying.
* Plain paper is selected for the paper type.
* When the Reversing Automatic Document Feeder is used, copying in the speed of 28, 35 and 45
sheets per minute are only possible under the following conditions:
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT 28 (11) 28 (11) 16 (5) 28 (11) 28 (11)
B5, A5-R, ST-R -
A4-R, B5-R, LT-R 21 (5) 21 (5) 16 (5) 21 (5) -
B4, LG 18 (5) 18 (5) 16 (5) 18 (5) -
A3, LD 16 (5) 16 (5) 16 (5) 16 (5) -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT 35 (11) 35 (11) 21 (5) 35 (11) 35 (11)
B5, A5-R, ST-R -
A4-R, B5-R, LT-R 28 (5) 28 (5) 21 (5) 28 (5) -
B4, LG 24 (5) 24 (5) 21 (5) 24 (5) -
A3, LD 21 (5) 21 (5) 21 (5) 21 (5) -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT 45 (11) 45 (11) 22 (5) 45 (11) 45 (11)
B5, A5-R, ST-R -
A4-R, B5-R, LT-R 32 (5) 32 (5) 22 (5) 32 (5) -
B4, LG 26 (5) 26 (5) 22 (5) 26 (5) -
A3, LD 22 (5) 22 (5) 22 (5) 22 (5) -
e-STUDIO281c/351c/451c SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES June 2005 © TOSHIBA TEC
1 - 2
Original: A4 or LT (single-sided)
Mode: APS and Automatic density not selected, Plain paper mode
Number of copies:
Black mode: 28 sheets or more (e-STUDIO281c), 35 sheets or more (e-STUDIO351c), 45 sheets
or more (e-STUDIO451c)
Color mode: 11 sheets or more
Reproduction ratio: 100%
* The values in ( ) can be realized in the color mode.
Thick paper / OHP
e-STUDIO281c
Thick1 (81 g/m
2
to 105 g/m
2
, 21 lb. Bond to 28 lb. Bond)
Thick2 (106 g/m
2
to 163 g/m
2
, 29 lb. Bond to 90 lb. Index)
Thick3 (164 g/m
2
to 209 g/m
2
, 91 lb. Index to 110 lb. Index)
OHP
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT 28 (11) 28 (11) 16 (5) 28 (11) 28 (11)
B5, A5-R, ST-R -
A4-R, B5-R, LT-R 20 (5) 20 (5) 16 (5) 20 (5) -
B4, LG 18 (5) 18 (5) 16 (5) 18 (5) -
A3, LD 16 (5) 16 (5) 16 (5) 16 (5) -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT, B5, A5-R, ST-R - 20 (6) 10 (2) - -
A4-R, B5-R, LT-R - 14 (3) 10 (2) - -
B4, LG - 11 (3) 10 (2) - -
A3, LD - 10 (2) 10 (2) - -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT, B5, A5-R, ST-R - 20 (2) 10 (2) - -
A4-R, B5-R, LT-R - 14 (2) 10 (2) - -
B4, LG - 11 (2) 10 (2) - -
A3, LD - 10 (2) 10 (2) - -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT - 10 (3) - - -
June 2005 © TOSHIBA TEC e-STUDIO281c/351c/451c SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES
1 - 3
1
e-STUDIO351c
Thick1 (81 g/m
2
to 105 g/m
2
, 21 lb. Bond to 28 lb. Bond)
Thick2 (106 g/m
2
to 163 g/m
2
, 29 lb. Bond to 90 lb. Index)
Thick3 (164 g/m
2
to 209 g/m
2
, 91 lb. Index to 110 lb. Index)
OHP
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT 30 (11) 30 (11) 16 (5) 30 (11) 30 (11)
B5, A5-R, ST-R -
A4-R, B5-R, LT-R 23 (5) 23 (5) 16 (5) 23 (5) -
B4, LG 19 (5) 19 (5) 16 (5) 19 (5) -
A3, LD 16 (5) 16 (5) 16 (5) 16 (5) -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT, B5, A5-R, ST-R - 20 (6) 10 (2) - -
A4-R, B5-R, LT-R - 14 (3) 10 (2) - -
B4, LG - 11 (3) 10 (2) - -
A3, LD - 10 (2) 10 (2) - -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT, B5, A5-R, ST-R - 20 (2) 10 (2) - -
A4-R, B5-R, LT-R - 14 (2) 10 (2) - -
B4, LG - 11 (2) 10 (2) - -
A3, LD - 10 (2) 10 (2) - -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT - 10 (3) - - -
e-STUDIO281c/351c/451c SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES June 2005 © TOSHIBA TEC
1 - 4
e-STUDIO451c
Thick1 (81 g/m
2
to 105 g/m
2
, 21 lb. Bond to 28 lb. Bond)
Thick2 (106 g/m
2
to 163 g/m
2
, 29 lb. Bond to 90 lb. Index)
Thick3 (164 g/m
2
to 209 g/m
2
, 91 lb. Index to 110 lb. Index)
OHP
* "-" means "Not acceptable".
* When originals are manually placed for single side, continuous copying.
* The bypass copying speed is measured with the paper size specified.
* The values in ( ) can be realized in the color mode.
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT 30 (11) 30 (11) 16 (5) 30 (11) 30 (11)
B5, A5-R, ST-R -
A4-R, B5-R, LT-R 23 (5) 23 (5) 16 (5) 23 (5) -
B4, LG 19 (5) 19 (5) 16 (5) 19 (5) -
A3, LD 16 (5) 16 (5) 16 (5) 16 (5) -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT, B5, A5-R, ST-R - 20 (6) 10 (2) - -
A4-R, B5-R, LT-R - 14 (3) 10 (2) - -
B4, LG - 11 (3) 10 (2) - -
A3, LD - 10 (2) 10 (2) - -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT, B5, A5-R, ST-R - 20 (2) 10 (2) - -
A4-R, B5-R, LT-R - 14 (2) 10 (2) - -
B4, LG - 11 (2) 10 (2) - -
A3, LD - 10 (2) 10 (2) - -
Paper supply
Paper size
Drawer
Bypass feed
PFP
LCF
(A4/LT only)
Size specified
Size not
specified
A4, LT - 10 (3) - - -
June 2005 © TOSHIBA TEC e-STUDIO281c/351c/451c SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES
1 - 5
1
* System copy speed
* Shows the period of time from when the [START] button is pressed until the message "Ready" is dis-
played. (10 sheets of A4/LT size original are set on the RADF and one of the copy modes above is
selected.)
* Setting: when in the Text/Photo mode with Automatic density and APS/AMS set to OFF, or when in
the sort mode with paper fed from the upper drawer.
* The Saddle Stitch Finisher and hole punch unit not installed.
* The values in ( ) are the speeds of when in the color mode.
Copy paper
yFirst copy time ......................... Approx. 6.8 sec. or less (black), approx. 16.2 sec. or less (color)
(A4/LT, upper drawer, 100%, original placed manually)
yWarming-up time ..................... Approx. 40 sec. (Stand-alone, temperature: 20°C)
yMultiple copying....................... Up to 999 copies; Key in set numbers
yReproduction ratio ................... Actual ratio: 100±0.5%
Zooming: 25 to 400% in increments of 1%
(25 to 200% when using RADF)
yResolution/Gradation............... Scanning: 600 dpi x 600 dpi
Printing: Equivalent to 2400 dpi x 600 dpi (black)
Equivalent to 600 dpi x 600 dpi (color)
Copy mode
Sec.
e-STUDIO281c e-STUDIO351c e-STUDIO451c
Single-sided originals
Single-sided copies
1 set 31.26 (71.97) 28.15 (71.97) 24.99 (71.97)
3 sets 74.07 (182.19) 61.02 (182.19) 50.03 (182.19)
5 sets 116.64 (289.94) 95.19 (289.94) 76.63 (289.94)
Single-sided originals
Double-sided copies
1 set 32.61 (81.63) 29.65 (81.63) 28.49 (81.63)
3 sets 74.69 (189.38) 64.92 (189.38) 60.76 (189.38)
5 sets 117.45 (299.04) 101.75 (299.04) 92.2 (299.04)
Double-sided originals
Double-sided copies
1 set 64.24 (138.12) 63.54 (138.12) 63.01 (138.12)
3 sets 150.73 (355.91) 134.25 (355.91) 126.36 (355.91)
5 sets 234.59 (574.51) 205.69 (574.51) 189.67 (574.51)
Double-sided originals
Single-sided copies
1 set 58.85 (128.31) 58.76 (128.31) 58.09 (128.31)
3 sets 143.68 (347.08) 126.57 (347.08) 110.94 (347.08)
5 sets 228.58 (565.02) 194.49 (565.02) 165.19 (565.02)
Drawer ADU PFP LCF Bypass copy Remarks
Size
A3 to A5-R,
LD to ST-R,
13" LG,
8.5"SQ
A4, LT
A3 to A6-R, LD to ST-R, 13"
LG, 8.5"SQ, 305 x 457 mm
(12" x 18")
(Non-standard or userspec-
ified sizes can be set.)
Weight
64 to 105 g/m
2
17 to 28 lb.
Bond
64 to 209 g/m
2
, 17 lb. Bond
to 110 lb. Index
(Continuous feeding)
64 to 209 g/m
2
, 17 lb. Bond
to 110 lb. Index
(Single paper feeding)
Special
paper
-
Labels, OHP film
(thickness: 80µm or thicker)
Special paper recom-
mended by Toshiba Tec
e-STUDIO281c/351c/451c SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES June 2005 © TOSHIBA TEC
1 - 6
yEliminated portion.................... Leading edges: 3.0±2.0 mm, Side/trailing edges: 2.0±2.0 mm (black
copy)
Leading edges: 5.0±2.0 mm, Side/trailing edges: 2.0±2.0 mm (color
copy)
Leading / trailing edges: 5.0±2.0 mm, Side edges: 5.0±2.0 mm (black /
color print)
yPaper feeding .......................... Standard drawers:
2 drawers (stack height 60.5 mm, equivalent to 550 sheets; 64 to 80 g/
m
2
(17 to 22 lb. Bond))
PFP:
Option (One drawer or two: stack height 60.5 mm, equivalent to 550
sheets; 64 to 80 g/m
2
(17 to 22 lb. Bond))
LCF:
Option (Stack height 137.5 mm x 2: equivalent to 2500 sheets; 64 to 80
g/m
2
(17 to 22 lb. Bond))
Bypass feeding:
Stack height 11 mm: equivalent to 100 sheets; 64 to 80 g/m
2
(17 to 22
lb. Bond)
yCapacity of originals in the reversing automatic document feeder (Option)
.................................................. A3 to A5-R, LD to ST-R:
100 sheets / 80 g/m
2
(Stack height 16 mm or less)
yAutomatic duplexing unit ......... Stackless, Switchback type
yToner supply ............................ Automatic toner density detection/supply
Toner cartridge replacing method
yDensity control......................... Automatic density mode and manual density mode selectable in 11
steps
yWeight ..................................... Approximately 113 kg (249 lb.)
yPower requirements ................ AC 110 V / 13.2 A, 115 V or 127 V / 12 A
220-240 V or 240 V / 8 A (50/60 Hz)
* The acceptable value of each voltage is ±10%.
yPower consumption................. 1.5 kW or less (100 V series), 17 kW or less (200 V series)
* The electric power is supplied to the RADF, Finisher, PFP and LCF through the equipment.
yTotal counter............................ Electronical counter
yDimensions of the equipment...................... See the figure below (W 660 x D 758 x H 739 (mm))
* When the tilt angle of the control panel is 45 degrees.
Fig.1-1
660
758
45°
739
June 2005 © TOSHIBA TEC e-STUDIO281c/351c/451c SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES
1 - 7
1
1.2 Accessories
* Machine version
NAD: North America
MJD: Europe
AUD: Australia
ASD: Asia, Argentine
TWD: Taiwan
SAD Saudi Arabia
ASU Saudi Arabia, Asia
CND China
KRD Korea
JPD: Japan
Unpacking/Setup instruction 1 set
Operator’s manual 4 pcs. (except for MJD and ASU)
Operator's manual pocket 1 pc.
Power cable 1 pc.
Warranty sheet 1 pc. (for NAD)
Setup report 1 set (for NAD, MJD and CND)
PM sticker 1 pc. (for MJD)
Drum (installed inside of the equipment) 1 pc.
Control panel stopper 1 pc.
Color developer holder 6 pc.
Rubber plug 4 pcs.
Blind seal (small / large) 3 pcs. /1 pc.
CD-ROM 3 pcs.
Developer material (Y, M, C, K) 1 pc. each (for CND)
Screw M4 x 8 1 pc.
Guide 1 pc.
Approval sheet 1 set (for CND)
Toner cartridge (Y, M, C, K) 1 pc. each (for CND)
Platen cover 1 pc. (for CND)
e-STUDIO281c/351c/451c SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES June 2005 © TOSHIBA TEC
1 - 8
1.3 Options
Notes:
1. The bridge kit (KN-3511) is necessary for installation of the finisher (MJ-1022, MJ-1023 or MJ-
1024).
2. The finisher (MJ-1023 or MJ-1024) is necessary for installation of the hole punch unit (MJ-
6004N/E/F/S).
3. The PCI slot (GO-1060) is necessary for the installation of the scrambler board (GP-1040)
and the parallel interface kit (GF-1140).
4. The antenna (GN-3010) is necessary to enable the wireless LAN module (GN-1040/1041)
and the bluetooth module (GN-2010).
5. Up to 1 antenna (GN-3010) can be connected to the wireless LAN module (GN-1040/1041).
6. When the wireless LAN module (GN-1040/1041) and the bluetooth module (GN-2010) are
installed together, only 1 antenna (GN-3010) can be connected to each.
Platen cover KA-3511PC / -C
Reversing Automatic Document Feeder (RADF) MR-3018
Drawer module MY-1021 / -C
Paper Feed Pedestal (PFP) KD-1011 / -C
Large Capacity Feeder (LCF) KD-1012 A4/LT / A4-C
Hanging Finisher MJ-1022 / -C
Finisher MJ-1023 / -C
Saddle Stitch Finisher MJ-1024 / -C
Hole punch unit MJ-6004 N/E/F/S / E-C
Staple cartridge STAPLE-1600 (for MJ-1022)
STAPLE-2000 (for MJ-1023/1024)
STAPLE-600
(for saddle stitcher of MJ-1024)
Bridge kit KN-3511 / -C
Work table KK-3511 / -C
Damp heater kit MF-3511U/E
FAX unit GD-1200 NA/AU/AS/EU/C/TW
2nd line for fax unit GD-1160 NA/EU-N/C/TW
128 MB Expansion memory GC-1181
512 MB Expansion memory GC-1230
Wireless LAN module GN-1040/1041
PCI slot GO-1060
Scrambler board GP-1040
Bluetooth module GN-2010
Antenna GN-3010
Parallel interface kit GF-1140
Data overwrite kit GP-1060
Desk MH-1700
Harness kit for coin controller GQ-1020
05/11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496
  • Page 497 497
  • Page 498 498
  • Page 499 499
  • Page 500 500
  • Page 501 501
  • Page 502 502
  • Page 503 503
  • Page 504 504
  • Page 505 505
  • Page 506 506
  • Page 507 507
  • Page 508 508
  • Page 509 509
  • Page 510 510
  • Page 511 511
  • Page 512 512
  • Page 513 513
  • Page 514 514
  • Page 515 515
  • Page 516 516
  • Page 517 517
  • Page 518 518
  • Page 519 519
  • Page 520 520
  • Page 521 521
  • Page 522 522
  • Page 523 523
  • Page 524 524
  • Page 525 525
  • Page 526 526
  • Page 527 527
  • Page 528 528
  • Page 529 529
  • Page 530 530
  • Page 531 531
  • Page 532 532
  • Page 533 533
  • Page 534 534
  • Page 535 535
  • Page 536 536
  • Page 537 537
  • Page 538 538
  • Page 539 539
  • Page 540 540
  • Page 541 541
  • Page 542 542
  • Page 543 543
  • Page 544 544
  • Page 545 545
  • Page 546 546
  • Page 547 547
  • Page 548 548
  • Page 549 549
  • Page 550 550
  • Page 551 551
  • Page 552 552
  • Page 553 553
  • Page 554 554
  • Page 555 555
  • Page 556 556
  • Page 557 557
  • Page 558 558
  • Page 559 559
  • Page 560 560
  • Page 561 561
  • Page 562 562
  • Page 563 563
  • Page 564 564
  • Page 565 565
  • Page 566 566
  • Page 567 567
  • Page 568 568
  • Page 569 569
  • Page 570 570
  • Page 571 571
  • Page 572 572
  • Page 573 573
  • Page 574 574
  • Page 575 575
  • Page 576 576
  • Page 577 577
  • Page 578 578
  • Page 579 579
  • Page 580 580
  • Page 581 581
  • Page 582 582
  • Page 583 583
  • Page 584 584
  • Page 585 585
  • Page 586 586
  • Page 587 587
  • Page 588 588
  • Page 589 589
  • Page 590 590
  • Page 591 591
  • Page 592 592
  • Page 593 593
  • Page 594 594
  • Page 595 595
  • Page 596 596
  • Page 597 597
  • Page 598 598
  • Page 599 599
  • Page 600 600
  • Page 601 601
  • Page 602 602

Toshiba Copier e-STUDIO281c Manuale utente

Categoria
Multifunzionali
Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue