Woodward easYgen-800 Manuale utente

easYgen-800

Manual Genset Control

easYgen-800

37691A

This is no translation but the original Technical Manual in English.

Designed in Germany and Poland; manufactured in China.

Woodward GmbH

Handwerkstrasse 29

70565 Stuttgart

Germany

Telephone: +49 (0) 711 789 54-510

Fax: +49 (0) 711 789 54-101

E-mail: [email protected]

Internet: http://www.woodward.com

37691AeasYgen-800 | Genset Control2

Brief Overview

Fig. 1: easYgen-800

1 Terminals 1 to 22: Power supply, relays, discrete

inputs, MPU, D+, ...

2 Terminals 23 to 26: CAN (J1939)

3 Terminals 33 to 35: RS-485 interface

4 USB service port for PC/laptop with ToolKit-SC

5 Terminals 62 to 64: RS-232 interface

6 ETHERNET interface connector (RJ-45)

7 Terminals 56 to 61: Analog inputs

8 Terminals 49 to 55 (screwable): Generator and

Ground current

9 Terminals 45 to 48: Generator voltage

10 Terminals 41 to 44: Intentionally not imple‐

mented

11 Terminals 36 to 40: Relay outputs

12 SD micro card slot

The easYgen-800 are control units for engine-generator system

management applications.

The control units can be used in applications such as: co-genera‐

tion, stand-by, AMF or distributed generation.

The following parts are included in the covering box. Please check

prior to the installation that all parts are present:

n Device easYgen genset control

All screwable terminal connectors are delivered with plug and

jack

n Clamp fastener installation material (4x)

n

“Installation Procedure Supplement”

paper with links to the

latest edition of Technical Documentation and software for

download:

(http://www.wwdmanuals.com/easYgen-800)

Configuration software and Technical Manual are

available at Woodward web site:

http://www.woodward.com/easYgen-800.aspx

Scope of delivery

Brief Overview

37691A easYgen-800 | Genset Control 3

Fig. 2: Sample application setup

A typical application mode for the control unit is the use for non

parallel operation in a single genset application.

n In this case, the easYgen will function as an engine control with

generator and engine protection.

n The control unit can open and close the circuit breaker .

Transition procedures are described in chapter

Ä Chapter 5.5 “Transition Procedures”

on page 99.

Sample application setup

Brief Overview

37691AeasYgen-800 | Genset Control4

Table of contents

1 General Information.................................................................................................................. 9

1.1 About This Manual...................................................................................................................... 9

1.1.1 Revision History.......................................................................................................................... 9

1.1.2 Depiction Of Notes And Instructions........................................................................................... 9

1.2 General Information................................................................................................................... 10

1.2.1 Copyright And Disclaimer.......................................................................................................... 10

1.2.2 Service And Warranty............................................................................................................... 11

1.2.3 Safety........................................................................................................................................ 11

1.2.3.1 Intended Use............................................................................................................................. 11

1.2.3.2 Personnel.................................................................................................................................. 12

1.2.3.3 General Safety Notes................................................................................................................ 13

2 System Overview..................................................................................................................... 15

2.1 Display and Status Indicators.................................................................................................... 15

2.2 Operation Modes....................................................................................................................... 16

2.2.1 Operation Mode AUTO.............................................................................................................. 16

2.2.2 Operation Mode MANual........................................................................................................... 16

2.2.3 Operation Mode STOP.............................................................................................................. 17

2.3 Features and Functions of both easYgen-800 and -1800......................................................... 17

2.4 Functions................................................................................................................................... 19

2.5 Intended Use of This Control..................................................................................................... 20

3 Installation............................................................................................................................... 21

3.1 Mounting.................................................................................................................................... 21

3.2 Wiring........................................................................................................................................ 21

3.3 Interfaces................................................................................................................................... 26

3.3.1 Ethernet Interface Connection................................................................................................... 26

3.4 Micro SD Card Slot.................................................................................................................... 27

3.5 Install ToolKit-SC....................................................................................................................... 28

4 Configuration........................................................................................................................... 29

4.1 Access to the Control................................................................................................................ 30

4.1.1 Access Via The Front Panel...................................................................................................... 30

4.1.1.1 Front Panel: Operating and Display Elements.......................................................................... 30

4.1.1.2 Front Panel Control................................................................................................................... 32

4.1.2 Configure ToolKit-SC................................................................................................................ 35

4.1.2.1 Configure Communication......................................................................................................... 35

4.1.2.2 Manage Configuration Data...................................................................................................... 35

4.1.2.3 Configure Customized Language.............................................................................................. 36

4.1.3 Access via ToolKit-SC Configuration Tool................................................................................ 37

Table of contents

37691A easYgen-800 | Genset Control 5

4.1.3.1 Read/Write Configuration.......................................................................................................... 38

4.2 Parameters................................................................................................................................ 38

4.2.1 Parameter Menu Structure........................................................................................................ 38

4.2.2 Parameter Settings Menu--HMI Access.................................................................................... 40

4.2.3 Configure Measurement............................................................................................................ 41

4.2.4 Configure Application................................................................................................................ 42

4.2.4.1 Configure Inputs and Outputs................................................................................................... 42

4.2.4.2 Configure Engine....................................................................................................................... 51

4.2.4.3 Configure TEST Run................................................................................................................. 52

4.2.4.4 Configure Breakers................................................................................................................... 53

4.2.5 Configure Monitoring................................................................................................................. 54

4.2.5.1 Monitoring Generator ............................................................................................................... 54

4.2.5.2 Monitoring Breakers.................................................................................................................. 57

4.2.5.3 Monitoring Engine..................................................................................................................... 57

4.2.5.4 Other Monitoring........................................................................................................................ 59

4.2.6 Configure Interfaces.................................................................................................................. 59

4.2.6.1 Configure GSM Module............................................................................................................. 60

4.2.6.2 Configure Ethernet Interface..................................................................................................... 62

4.2.7 Configure Maintenance............................................................................................................. 63

4.2.8 Configure Counters................................................................................................................... 65

4.2.9 Configure Switchable Parameter Set........................................................................................ 66

4.2.10 Configure Language / Clock...................................................................................................... 66

4.2.11 Configure System Management................................................................................................ 67

4.2.12 Configure HMI........................................................................................................................... 67

4.3 Selectable Inputs/Outputs/Sensors........................................................................................... 69

4.3.1 Programmable Sensors............................................................................................................. 69

4.3.2 Programmable Inputs................................................................................................................ 70

4.3.3 Programmable Outputs............................................................................................................. 72

4.4 Status Menu.............................................................................................................................. 76

4.4.1 HMI Status Screens.................................................................................................................. 76

4.4.2 ToolKit-SC Status Screens........................................................................................................ 77

4.4.3 Configure For Using Accessories.............................................................................................. 79

4.4.3.1 Digital Input Module WWDIN16................................................................................................. 80

4.4.3.2 Digital Output Module WWDOUT16.......................................................................................... 87

5 Operation................................................................................................................................. 91

5.1 Front Panel: Operating and Display Elements.......................................................................... 91

5.2 Warning/Alarm Signaling........................................................................................................... 93

5.2.1 Alarm Acknowledgment............................................................................................................. 93

5.3 Operation Modes....................................................................................................................... 94

5.3.1 Operation Mode AUTO.............................................................................................................. 94

5.3.2 Operation Mode MANual........................................................................................................... 94

Table of contents

37691AeasYgen-800 | Genset Control6

5.3.3 Operation Mode STOP.............................................................................................................. 94

5.4 START/STOP Operation........................................................................................................... 95

5.4.1 Start engine to supply load........................................................................................................ 95

5.4.2 Stop engine............................................................................................................................... 96

5.4.3 MANual START/STOP.............................................................................................................. 99

5.5 Transition Procedures............................................................................................................... 99

5.5.1 Disconnect during Cranking...................................................................................................... 99

5.6 Trouble Shooting..................................................................................................................... 100

6 Application............................................................................................................................. 101

6.1 Commissioning........................................................................................................................ 101

7 Interfaces and Protocols...................................................................................................... 103

7.1 J1939....................................................................................................................................... 103

8 Technical Specifications...................................................................................................... 109

8.1 Measuring and Monitoring....................................................................................................... 111

9 Appendix................................................................................................................................ 113

9.1 Alarms and Warnings.............................................................................................................. 113

9.1.1 Alarm Classes......................................................................................................................... 113

9.1.2 Warnings................................................................................................................................. 113

9.1.3 Shutdown Alarms.................................................................................................................... 114

9.1.4 Trip and Stop Alarms............................................................................................................... 116

9.1.5 Trip Alarms.............................................................................................................................. 116

9.2 Trouble Shooting..................................................................................................................... 117

9.3 Data Telegrams....................................................................................................................... 117

9.3.1 Modbus Basics........................................................................................................................ 117

9.3.1.1 Data Frame Format................................................................................................................. 118

9.3.1.2 Modbus Communication Protocol........................................................................................... 118

9.3.1.3 Information Frame Format....................................................................................................... 118

9.3.1.4 Address Code.......................................................................................................................... 119

9.3.1.5 Function Code......................................................................................................................... 119

9.3.1.6 Data Field................................................................................................................................ 120

9.3.1.7 Error Check Code (CRC)........................................................................................................ 120

9.3.1.8 Error Handling......................................................................................................................... 124

9.3.2 Read Holding Registers 03_hex.............................................................................................. 125

9.3.3 Force Single Coil 05H_hex...................................................................................................... 147

9.3.4 Preset Single Register 06H_hex............................................................................................. 148

9.3.4.1 Generator Status..................................................................................................................... 148

9.3.4.2 Remote Start Status................................................................................................................ 148

9.3.4.3 Breaker Status......................................................................................................................... 149

Table of contents

37691A easYgen-800 | Genset Control 7

10 Glossary And List Of Abbreviations.................................................................................... 151

11 Index....................................................................................................................................... 153

Table of contents

37691AeasYgen-800 | Genset Control8

1 General Information

1.1 About This Manual

1.1.1 Revision History

Rev. Date Editor Changes

NEW 2018-03 GG Describes device implemented software version 2.x and ToolKit-SC version 1.1.x.x

Technical Manual

n Release = 1st issue

1.1.2 Depiction Of Notes And Instructions

Safety instructions are marked with symbols in these instructions.

The safety instructions are always introduced by signal words that

express the extent of the danger.

DANGER!

This combination of symbol and signal word indi‐

cates an immediately-dangerous situation that

could cause death or severe injuries if not avoided.

WARNING!

This combination of symbol and signal word indi‐

cates a possibly-dangerous situation that could

cause death or severe injuries if it is not avoided.

CAUTION!

This combination of symbol and signal word indi‐

cates a possibly-dangerous situation that could

cause slight injuries if it is not avoided.

NOTICE!

This combination of symbol and signal word indi‐

cates a possibly-dangerous situation that could

cause property and environmental damage if it is

not avoided.

This symbol indicates useful tips and recommen‐

dations as well as information for efficient and

trouble-free operation.

To emphasize instructions, results, lists, references, and other ele‐

ments, the following markings are used in these instructions:

Safety instructions

Tips and recommendations

Additional markings

General Information

About This Manual > Depiction Of Notes And Ins...

37691A easYgen-800 | Genset Control 9

Marking Explanation

Step-by-step instructions

ð

Results of action steps

References to sections of these instructions and to

other relevant documents

Listing without fixed sequence

[Buttons]

Operating elements (e.g. buttons, switches), display

elements (e.g. signal lamps)

“Display”

Screen elements (e.g. buttons, programming of func‐

tion keys)

“Screen xx

è

Screen xy

è

Screen xz”

...

Menu path.

The following information and setting refer to a page

on HMI screen or ToolKit located as described here.

Some parameters/settings/screens are available only

either in ToolKit or in HMI/display.

Dimensions in Figures

All dimensions shown with no units specified are in

mm.

1.2 General Information

1.2.1 Copyright And Disclaimer

Disclaimer

All information and instructions in this manual have been provided

under due consideration of applicable guidelines and regulations,

the current and known state of the art, as well as our many years

of in-house experience. Woodward assumes no liability for dam‐

ages due to:

n Failure to comply with the instructions in this manual

n Improper use / misuse

n Willful operation by non-authorized persons

n Unauthorized conversions or non-approved technical modifica‐

tions

n Use of non-approved spare parts

The originator is solely liable to the full extent for damages caused

by such conduct. The agreed upon obligations in the delivery con‐

tract, the general terms and conditions, the manufacturer’s delivery

conditions, and the statutory regulations valid at the time the con‐

tract was concluded, apply.

Copyright

This manual is protected by copyright. No part of this manual may

be reproduced in any form or incorporated into any information

retrieval system without written permission of Woodward GmbH.

Delivery of this manual to third parties, duplication in any form -

including excerpts - as well as exploitation and/or communication

of the content, are not permitted without a written declaration of

release by Woodward GmbH.

General Information

General Information > Copyright And Disclaimer

37691AeasYgen-800 | Genset Control10

Actions to the contrary will entitle us to claim compensation for

damages. We expressly reserve the right to raise any further

accessory claims.

1.2.2 Service And Warranty

By opening the device you will lose any warranty!

CAUTION!

Any unauthorized modifications or using this equip‐

ment outside its specified mechanical, electrical, or

other operating limits may cause personal injury

and/or property damage, including damage to the

equipment.

Any such unauthorized modifications

n constitute "misuse" and/or "negligence" within the meaning of

the product warranty

n thereby excluding warranty coverage for any resulting damage,

and

n invalidate product certifications or listings.

Our Customer Service is available for technical information.

Please see page 2 for the contact data.

In addition, our employees are constantly interested in new infor‐

mation and experiences that arise from usage and could be val‐

uable for the improvement of our products.

Please enquire about the terms of warranty from

your nearest Woodward representative.

For our contact search webpage please go to:

http://www.woodward.com/Directory.aspx

1.2.3 Safety

1.2.3.1 Intended Use

The easYgen unit has been designed and constructed solely for

the intended use described in this manual.

The easYgen unit has been designed and constructed solely for

the intended use described in this Operation Manual and--with

even more details-- in the Technical Manual.

n Intended use requires operation of the control unit within the

specifications listed in

Ä Chapter 8 “Technical Specifications”

on page 109

.

n Intended use requires operation of the control unit within the

written specifications.

n All permissible applications are outlined in

Ä Chapter 6 “Appli‐

cation” on page 101

.

n Intended use includes compliance with all instructions and

safety notes presented in this manual.

Warranty terms

General Information

General Information > Safety > Intended Use

37691A easYgen-800 | Genset Control 11

n Any use which exceeds or differs from the intended use shall

be considered improper use.

n No claims of any kind for damage will be entertained if such

claims result from improper use.

NOTICE!

Damage due to improper use!

Improper use of the remote panel unit may cause

damage to the control unit as well as connected

components.

Improper use includes, but is not limited to:

– Operation outside the specified operation con‐

ditions.

1.2.3.2 Personnel

WARNING!

Hazards due to insufficiently qualified per‐

sonnel!

If unqualified personnel perform work on or with

the control unit hazards may arise which can

cause serious injury and substantial damage to

property.

– Therefore, all work must only be carried out by

appropriately qualified personnel.

This manual specifies the personnel qualifications required for the

different areas of work, listed below:

n Well trained for electrical installations.

n Skilled and competent to be aware especially of the local

safety regulations.

n Experienced in working on electronic measuring and control

devices.

n Allowed to manage the controlled (engine/generator) system.

The workforce must only consist of persons who can be expected

to carry out their work reliably. Persons with impaired reactions due

to, for example, the consumption of drugs, alcohol, or medication

are prohibited.

When selecting personnel, the age-related and occupation-related

regulations governing the usage location must be observed.

General Information

General Information > Safety > Personnel

37691AeasYgen-800 | Genset Control12

1.2.3.3 General Safety Notes

DANGER!

Moving parts and dangerous electricity!

Be aware that the remote control of a system that

is managing life dangerous engine-generator-elec‐

tricity parts needs attention for the local situation!

The following safety notes cover both the device

itself and basics of the overall genset system. The

dedicated genset-system related safety instruction

must be taken into account, too!

WARNING!

Hazards due to insufficient prime mover pro‐

tection

The engine, turbine, or other type of prime mover

should be equipped with an overspeed (over-tem‐

perature, or over-pressure, where applicable) shut‐

down device(s), that operates totally independently

of the prime mover control device(s) to protect

against runaway or damage to the engine, turbine,

or other type of prime mover with possible personal

injury or loss of life should the mechanical-

hydraulic governor(s) or electric control(s), the

actuator(s), fuel control(s), the driving mecha‐

nism(s), the linkage(s), or the controlled device(s)

fail.

Hazards by system controlled

Prime mover safety

General Information

General Information > Safety > General Safety Notes

37691A easYgen-800 | Genset Control 13

General Information

General Information > Safety > General Safety Notes

37691AeasYgen-800 | Genset Control14

2 System Overview

The easYgen is a stand-alone genset controller with measuring,

monitoring, and breaker control functionality. It comes with a easy

mounting plastic housing covering a well tested electronic-electrical

system.

Display and buttons of the HMI offer both access to states and

values, and access to the application. Password protection enables

dedicated operation access levels. Remote control, monitoring, vis‐

ualization, and configuration are possible via integrated interfaces.

Communication between easYgens, with PLC control, or as a net‐

work member offers an enhanced system management range;

additionally supported by easy to implement accessories.

For even higher challenges in genset control the

easYgen series offers further solutions up to the

most complex and ambitious applications.

For dedicated protection tasks ask Woodward for

its protection (relay) solutions.

2.1 Display and Status Indicators

HMI and the configuration software enable access to control, set‐

tings, and visualization. The front panel offers a number of func‐

tional defined buttons and a set of menu management buttons.

LEDs visualize fixed states, the graphic display works together with

the menu management buttons to show all necessary information.

Restrictions

Full access to all parameters and settings with con‐

figuration software only!

HMI access offers a number of information screens

in general, and enables - password protected -

access to parameters and settings.

General notes

General Notes

System Overview

Display and Status Indicators

37691A easYgen-800 | Genset Control 15

Fig. 3: easYgen-800

2.2 Operation Modes

The easYgen offers three operation modes:

n AUTO

n MANUAL (MAN)

n STOP

n ... and an internal (non) operating phase during starting the

device itself

The operation mode can be initiated - if current settings allow this

function:

n directly by pressing the according button at the front panel

n directly by click on the according button at the ToolKit-SC

remote screen

n via discrete inputs

n via interface

2.2.1 Operation Mode AUTO

In operation mode AUTO both genset and breaker are under

easYgen control. Start and stop of the engine is managed automat‐

ically together with opening/closing the breaker.

Depending on settings and application status, AUTO control can:

n supply load by generator

n start the engine

n stop the engine

2.2.2 Operation Mode MANual

In operation mode MANual both genset and breakers are inde‐

pendently from each other under easYgen control.

General notes

System Overview

Operation Modes > Operation Mode MANual

37691AeasYgen-800 | Genset Control16

Start and stop of the engine is managed with the same procedure

as in AUTO mode but without breaker control. Breakers can be

opened and closed without taking care of load or genset state!

2.2.3 Operation Mode STOP

In operation mode STOP the breaker is open and engine is not

running.

This is a configurable operation mode, only. This is

NO emergency STOP!

2.3 Features and Functions of both easYgen-800 and -1800

Both easYgen-800 and easYgen-1800 are very close in hardware

and software. The easYgen-1800 is the device with more/higher

functionality. For comparison and better differentiation both are

described below.

easYgen-800 is intended to be used for single automation sys‐

tems, auto start/stop of the unit are performed with the help of

remote signal.

easYgen-1800 has all functions of easYgen-800 as well as auto‐

matic mains failure function (AMF), particularly well suited for

single automation systems that include mains and generator.

Item

easYgen-800 easYgen-1800

LCD (with backlight) Dimension 4.3” 4.3”

Pixel 480 x 272 480 x 272

AMF no ●

Input Port Number 8 8

Output port Number 8 8

Sensor number 5 5

Neutral (earth) current ● ●

Schedule function ● ●

RS485 ● ●

Ethernet ● ●

GSM ● ●

J1939 ● ●

USB ● ●

Micro SD card (slot) ● ●

Real-time clock ● ●

Event log ● ●

General notes

Functional Blocks

System Overview

Features and Functions of bo...

37691A easYgen-800 | Genset Control 17

n With ARM-based 32-bit SCM, highly integrated hardware, high

reliability level

n Multilingual interface (including English, Chinese or other cus‐

tomer specific languages) which can be chosen at the site,

making commissioning convenient for factory personnel

n Improved LCD wear-resistance and scratch resistance due to

hard screen acrylic

n Silicon panel and pushbuttons for better operation in high-tem‐

perature environment

n RS-485 communication port enabling remote control, remote

measuring, remote communication via ModBus protocol

n SMS (Short Message Service) function: When genset is

alarming, controller can send short messages via SMS auto‐

matically to max. 5 telephone numbers (external GSM modem

is needed). Besides this, generator status can be controlled

and checked.

n Equipped with CAN bus port to communicate with J1939

genset. Monitoring frequently-used data such as water temper‐

ature, oil pressure, speed, fuel consumption and so on of ECU

machine, and additionally also control start, stop, raising

speed, and speed droop via CAN bus port

n Suitable for 3-phase 4-wire, 3-phase 3-wire, single phase 2-

wire, and 2-phase 3-wire systems with voltage 120/240 V and

frequency 50/60 Hz

n easYgen-1800 only: Collects and shows 3-phase voltage, cur‐

rent, power parameter and frequency of generator or mains.

Mains Generator Line voltage (U

AB

, U

BC

, and U

CA

) Line voltage

(U

AB

, U

BC

, and U

CA

) Phase voltage (U

A

, U

B

, and U

C

) Phase

voltage (U

A

, U

B

, and U

C

)

n easYgen-800 only: Collects and shows 3-phase voltage, cur‐

rent, power parameter and frequency of generator. Generator

Line voltage (U

AB

, U

BC

, and U

CA

) Line voltage (U

AB

, U

BC

, and

U

CA

) Phase voltage (U

A

, U

B

, and U

C

) Phase voltage (U

A

, U

B

,

and U

C

)

n Phase sequence, frequency, Load current I

A

, I

B

, I

C

n Each phase: Total active power [kW], Total reactive power

[kvar], Total apparent power [kVA], Average power factor PF

n Accumulated Total generator power [kWh], [kvarh], [kVAh], and

Earth current

n easYgen-1800 only: For Mains, controller has over and under

voltage, over and under frequency, loss of phase and phase

sequence wrong detection functions

n For generator, controller has over and under voltage, over and

under frequency, loss of phase, phase sequence wrong, over

and reverse power, over current functions

n 3 fixed analog sensors (temperature, oil pressure and fuel

level)

n Flexible sensors can be set as temperature sensor, oil pres‐

sure sensor or level sensor

n Precision measure and display parameters about Engine,

Temp. (WT) °C/°F both be displayed Oil pressure (OP)

kPa/psi/bar all be displayed Fuel level (FL) %(unit) Speed

(SPD) r/min (unit) Battery Voltage (VB) V (unit) Charger

Voltage (VD) V (unit) Hour count (HC) can accumulate to max.

65535 hours. Start times can accumulate to max. 65535 times

n Protection: automatic start/stop of the genset, ATS (Auto

Transfer Switch) control with perfect failure indication and pro‐

tection function

n All output ports are relay-out

Key characteristics

System Overview

Features and Functions of bo...

37691AeasYgen-800 | Genset Control18

n Parameter setting: parameters can be modified and stored in

internal FLASH memory and cannot be lost even in case of

power outage; most of them can be adjusted using front panel

of the controller and all of them can be modified using ToolKit-

SC configuration software on PC via USB, Ethernet, or RS485

ports

n More kinds of curves of temperature, oil pressure, fuel level

can be used directly and users can define the sensor curves by

themselves

n Multiple crank disconnect conditions (generator frequency,

speed sensor, oil pressure) are optional

n Widely power supply range DC (8 to 35) V, suitable to different

start battery voltage environment

n Event log, real-time clock, scheduled start & stop generator

(can be set as start genset once a day/week/month whether

with load or not)

n Logon wallpaper and display time are user-defined

n Can be used on pumping units and as an indicating instrument

(indicate and alarm are enable only, relay is inhibited)

n With maintenance function. Actions (warning or shutdown) can

be set when maintenance time out

n All parameters are digital adjusted (instead of conventional

analog modulation with normal potentiometer) for more relia‐

bility and stability

n Waterproof security level IP55 due to rubber seal installed

between the controller enclosure and front panel

n Metal fixing clips enable perfect in high temperature environ‐

ment

n Modular design, self-extinguishing ABS plastic enclosure, plug‐

gable connection terminals and embedded installation way;

compact structure with easy mounting

n Accumulation of total run time and total electric energy of A

and B. Users can reset it for convenience.

2.4 Functions

n Protection: automatic start/stop of the genset, ATS (Auto

Transfer Switch) control with failure indication and protection

function

n All output ports are relay-out

n Parameter setting: parameters can be modified and stored in

internal FLASH memory and cannot be lost even in case of

power outage; most of them can be adjusted using front panel

of the controller and all of them can be modified using ToolKit-

SC on a PC via USB or RS485 ports.

n Curves of temperature, oil pressure, fuel level can be used

directly and users can define the sensor curves by themselves

n Multiple crank disconnect conditions (generator frequency,

speed sensor, oil pressure) are optional

n Event log, real-time clock, scheduled start & stop generator

(can be set as start genset once a day/week/month whether

with load or not)

n Logon wallpaper and display time are user-defined

n Can be used on pumping units and as an indicating instrument

(indicate and alarm are enable only, relay is inhibited)

n Maintenance function: Actions (warning or shutdown) can be

set when maintenance time out

System Overview

Functions

37691A easYgen-800 | Genset Control 19

n All parameters use digital adjustment, instead of conventional

analog modulation with normal potentiometer for more relia‐

bility and stability

n Accumulative total run time and total electric energy of A and

B. User can reset it as 0 and re-accumulative the value which

allows to count the total value user defined.

2.5 Intended Use of This Control

easYgen-800 genset controllers are used for

n genset automation and monitor control system of single unit to

achieve

n automatic start/stop,

n data measurement,

n alarm protection and

n three remote features: control, measuring and communication.

The controller adopts large liquid crystal display (LCD) and select‐

able Chinese, English or other languages interface with easy and

reliable operation.

This easYgen genset controllers adopt 32 bits micro-processor

technology with precision parameters measuring, fixed value

adjustment, time setting and threshold adjusting and etc. The

majority of parameters can be set using front panel and all the

parameters can be set using PC (via USB port) and can be

adjusted and monitored with the help of RS-485 port. It can be

widely used in a number of automatic genset control system with

compact structure, simple connections and high reliability

System Overview

Intended Use of This Control

37691AeasYgen-800 | Genset Control20

La pagina sta caricando ...

Woodward easYgen-800 Manuale utente

Questo manuale è adatto anche per

Woodward easYgen-800 Manuale utente

in altre lingue

Altri documenti