Simplicity SNAPPER PREMIUM RIDER, LT75 15,5/17,5 CE Manuale utente

Part No. 885378

Revision -

Original Instructions

Mfg. No. Description

7800672 Snapper LT75 RD Rider 15,5HP (CE)

7800676 Snapper LT75 RD Rider 17,5HP (CE)

Premium Rider (CE)

en

Operator’s Manual

Bedienungsanleitung

de

Manuale dell’operatore

fr

it

nl

Instrukcja obsługi

pl

Manuel d’utilisation

Gebruikershandleiding

es

Manual del operador

Manual do operador

pt

Not for

Reproduction

2

Not for

Reproduction

3/8

7

4

3

5

1

2

8

6

3

1

3

4

2

Not for

Reproduction

4

2

1

5

7

6

1

2

3

8

Not for

Reproduction

5

10

11

12

9

Not for

Reproduction

6

2

1

15 16

A

B

13 14

Not for

Reproduction

7

17 18

2019

Not for

Reproduction

8

4

2

1

3

2

23

24

2

1

4

3

21

4

1

3

2

22

Not for

Reproduction

9

en

Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Parts and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table of Contents

Not for

Reproduction

10

en

6. All drivers should seek and obtain professional and

practical instruction. Such instruction

should emphasize:

a. the need for care and concentration when

working with ride-on machines;

b. control of a ride-on machine sliding on a slope

will not be regained by the application of the

brake. The main reasons for loss of control are:

• insufficient wheel grip;

• being driven too fast;

• inadequate braking;

• the type of machine is unsuitable for

its task;

• lack of awareness of the effect of

ground conditions, especially slopes;

• incorrect hitching and

load distribution.

Preparation

1. While mowing, always wear substantial footwear

and long trousers. Do not operate the equipment

when barefoot or wearing open sandals.

2. Thoroughly inspect the area where the equipment

will be used and remove all objects which may be

thrown by the machine.

3. WARNING-Fuel is highly flammable.

a. Store fuel in containers specifically

designed for this purpose.

b. Refuel outdoors only and do not smoke

while refuelling.

c. Add fuel before starting the engine. Never

remove the cap of the fuel tank or add fuel

while the engine is running or when the engine

is hot.

d. If fuel is spilled, do not attempt to start the

engine but move the machine away from the

area of spillage and avoid creating any source

of ignition until the fuel vapors have dissipated.

e. Replace all fuel tanks and container

caps securely.

4. Replace faulty silencers.

5. Before using, always visually inspect to see that

the blades, blade bolts, and cutter assembly are

not worn or damaged. Replace worn or damaged

blades and bolts in sets to preserve balance.

6. On multi-blade machines, take care as rotating one

blade can cause other blades to rotate.

KNOW YOUR PRODUCT

If you understand the unit and how the unit operates, you

will get the best performance. As you read this manual,

compare the illustrations to the unit. Learn the location

and the function of the controls. To help prevent an

accident, follow the operating instructions and the safety

rules. Save these original instructions for future reference.

It is the responsibility of the owner to follow the

instructions contained in this manual.

FOR RIDE-ON (RIDING) ROTARY

MOWER MACHINES

Training

1. Read the instructions carefully. Be familiar with the

controls and the proper use of the equipment.

2. Never allow children or people unfamiliar with these

instructions to use the mower. Local regulations

may restrict the age of the operator.

3. Never mow while people, especially children, or

pets are nearby.

4. Keep in mind that the operator or user is

responsible for accidents or hazards occurring to

other people or their property.

5. Do not carry passengers.

Operator Safety

WARNING

Look for this symbol to indicate important

safety precautions. This symbol indicates:

“Attention! Be Alert! Your Safety Is At Risk.”

WARNING

This cutting machine is capable of amputating

hands and feet and throwing objects. Failure to

observe the following safety instructions could

result in serious injury or death to the operator

or bystanders.

Not for

Reproduction

11

en

Operator Safety

Operation

1. Do not operate the engine in a confined space

where dangerous carbon monoxide fumes

can collect.

2. Mow only in daylight or in good artificial light.

3. Before attempting to start the engine, disengage all

blade attachment clutches and shift into neutral.

4. Do not use on slopes of more than 10 degrees.

5. Remember there is no such thing as a “safe” slope.

Travel on grass slopes requires particular care. To

guard against overturning:

a. do not stop or start suddenly when going up

or downhill;

b. engage clutch slowly, always keep machine in

gear, especially when travelling downhill;

c. machine speeds should be kept low on slopes

and during tight turns;

d. stay alert for humps and hollows and other

hidden hazards;

e. never mow across the face of the slope, unless

the mower is designed for this purpose.

6. Use care when pulling loads or using

heavy equipment.

a. Use only approved drawbar hitch points.

b. Limit loads to those you can safely control.

c. Do not turn sharply. Use care when driving

in reverse.

d. Use counterweight(s) or wheel weights when

suggested in the Operator’s Manual.

7. Watch out for traffic when crossing or

near roadways.

8. Stop the blades rotating before crossing surfaces

other than grass.

9. When using any attachments, never direct the

discharge of material toward bystanders nor allow

anyone near the machine while in operation.

10. Never operate the mower with defective guards or

shields, or without safety protective devices

in place.

11. Do not change the engine governor settings or

overspeed the engine. Operating an engine at

excessive speed may increase the hazard of

personal injury.

12. Before leaving the operator’s position

a. disengage the power take-off and lower

the attachments;

b. change into neutral and set the parking brake;

c. stop the engine and remove the key.

13. Disengage drive to attachments, stop the engine,

and disconnect the spark plug wire(s) or remove

the ignition key

a. before cleaning blockages or

unclogging chute;

b. before checking, cleaning, or working on

the mower;

c. after striking a foreign object. Inspect the

mower for damage and make repairs before

restarting and operating the equipment;

d. if the machine starts to vibrate abnormally

(check immediately).

14. Disengage drive to attachments when transporting

or not in use.

15. Stop the engine and disengage drive to

the attachment

a. before refuelling;

b. before removing the grass bagger;

c. before making height adjustment unless

adjustment can be made from the operator’s

position.

16. Reduce the throttle setting during engine run-out

and, if the engine is provided with a shut-off valve,

turn the fuel off at the conclusion of mowing.

17. Before and when backing, look behind and down

for small children.

18. Use extra care when approaching blind corners,

shrubs, trees or other objects that may

obscure vision.

Maintenance and Storage

1. On multi-blade machines, take care as rotating one

blade can cause other blades to rotate.

2. When machine will be parked, stored or left

unattended, lower the cutting means unless a

positive mechanical lock is used.

3. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

4. Never store the equipment with fuel in the tank

inside a building where fumes may reach an open

flame or spark.

5. Allow the engine to cool before storing in

any enclosure.

6. To reduce the fire hazard, keep the engine, silencer,

battery compartment and fuel storage area free of

grass, leaves, or excessive grease.

7. Check the grass bagger frequently for wear

or deterioration.

8. Replace worn or damaged parts for safety.

9. If the fuel tank has to be drained, this should be

done outdoors.

Not for

Reproduction

12

en

Operator Safety

(

)

20LB

(

)

34

LB

_

All safety and operation decals should be carefully

read and followed.

Decal - Operating Instructions (CE)

(1734027)

Decal - Parking

Brake (724281)

Decal - Ignition

Switch (1722806)

Decal - Cutting

Height (885253)

Decal - Roll Release

(1723425)

Decal - Hot Surface

(885216)

Decal - Throttle

Control (885171)

Decal - Discharge Tube

(1721107)

Decal - Fire

Hazard (885218)

Decal - Brake/Clutch

Control (729695)

Decal - Speed Control

Pedal (885169)

Decal - Draw Bar Load

(729677)

ID Tag

Decal - Sever Hazard (885217)

Serious personal injury and/or equipment damage can

result when these decals are not followed.

Not for

Reproduction

13

en

Operator Safety

IMPORTANT: The following

symbols are located on your unit

or on literature supplied with the

product. Before you operate the

unit, learn and understand the

purpose for each symbol.

Safety Warning Symbols

1 WARNING.

2 IMPORTANT: Read Owner’s

Manual Before Operating This

Machine.

3 WARNING: Thrown Objects.

Keep Bystanders Away. Read

User Instructions Before

Operating This Machine.

4 WARNING: Do Not Use This

Machine On Slopes Greater

Than 10 Degrees.

5 DANGER: Keep People,

Especially Children, Away

From Unit.

6 DANGER: Stay Clear Of Mower

Blade As Long As Engine Is

Running.

7 DANGER: Keep Feet And

Hands Away From Rotating

Blade.

8 DANGER: Disconnect Spark

Plug Wire Before Servicing

Unit.

9 WARNING: Hot Surface.

10 WARNING: Use Caution When

Connecting Or Disconnecting

Accessories.

11 WARNING: Crushed Fingers.

12 IMPORTANT: Follow

Instructions In Owner’s Manual

To Level The Deck.

13 DANGER: Stay Clear Of Mower

Blade As Long As Engine Is

Running.

14 WARNING: Discharge Tube. Do

not operate as a bagger unless

discharge chute is in place.

15 WARNING: Fire Hazard. Yard

debris is combustible. Keep

unit cleaned of debris.

Control and Operating

Symbols

1 Engine Start

2 Engine Stop

3 Engine Run

4 Brake

5 Parking Brake

6 Clutch

7 Slow

8 Fast

9 Choke

10 Oil

11 Blade Rotation Control

12 Fuel

1

2

3

4

5

6

7

8

9

10

11

12

Not for

Reproduction

14

en

Assembly

NOTE: All fasteners are in the parts bag. Do not

discard any parts or material until the unit

is assembled.

Before doing any assembly or maintenance to the

mower, remove the wire from the spark plug.

Install the Front Wheels

1. Make sure the valve stem (1) is to the outside

(see Figure 1).

2. Slide the front wheel (2) onto the spindle (3).

3. Secure the front wheel (2) with washers (4 and 5),

and cotter pin (6) Bend the ends of the cotter pin

apart to keep the front wheel on the spindle.

4. If your model has hub caps (7), install the hubcaps.

Make sure the washers hold the hubcaps in place.

5. Repeat for opposite side.

Install the Seat

1. Carefully remove the plastic bag from the seat.

2. Raise the seat support (1) (see Figure 2).

3. Align the holes in the seat (2) to the slots in the

seat support.

4. Install the seat (2) to the seat support (1) and

adjustment lever (3) with washers (4) and bolts (5).

NOTE: Install the washers on the left side only.

5. Connect the wiring harness (6) to the seat switch

(7) under the seat.

6. Lower the seat to the normal operating position.

7. Check the operation of the seat adjustment.

a. If the seat needs adjustment, raise the

adjustment lever (3) toward the seat and move

the seat to the desired position.

b. Release the adjustment lever to lock the seat

in place.

Assemble the Steering Wheel

1. Make sure the front wheels point forward as shown

in Figure 3.

2. Slide the bellows (1) over the console.

3. Slide the steering post (2) into the console.

4. Attach the steering wheel (3) to the steering post

(2) with screw (4) and washer (5). Tighten screw

but be careful not to over-tighten.

a. Push on the steering wheel. The steering post

will lock onto the pinion gear (6).

b. Pull on the steering wheel. Make sure that the

steering post is locked in place.

5. Install the plate (7) and cover (8) to the

steering wheel.

Assemble the Grass Bag

1. Slide the bottom tube (1) onto the bagger frame (2)

(see Figure 4).

2. Align the holes in bottom tube with hole in the

bagger frame.

3. Install the cotter pins (3) into holes and bend the

ends to secure to the frame.

4. Slide the frame assembly onto the grass bag (4).

5. Attach the bag clips to the frame assembly.

6. Align the bagger cover (5) to holes in frame.

7. Use screws (6) and (7) to assemble the side and

top of the cover to the bagger frame.

8. Assemble the bagger handle (8) thru hole in cover

and frame.

9. Secure the bagger handle with washer (9), screw

(10), and nut (11).

10. Install rear bagger handle (12) to cover using two

screws (13).

Not for

Reproduction

15

en

Assembly

Mount the Grass Bag

1. Mount the grass bag assembly onto the rear

bagger brackets as shown (see Figure 5).

a. Use one hand to grab onto the handle at the

rear of the bag frame assembly.

b. Use the other hand to hold the top bagger

handle and guide the bag frame assembly

onto the rear bagger brackets.

2. When mounting the bagger frame assembly, hold

the bottom of the grass bagger assembly slightly

away from the rear plate.

3. Rotate the grass bagger assembly until it locks

in place.

4. If the bagger frame assembly fails to lock in place, adjust

the two latches (see Figure 6).

5. Remove the side and bottom trim pieces of grass bag

from bagger frame.

6. Loosen the two screws and adjust the latch until it

contacts the bagger frame assembly.

7. Tighten the screws and check that the bagger frame

assembly will lock when closed.

8. Reinstall the side and bottom trim pieces of grass bag to

bottom tube.

9. If the bagger frame assembly will not stay locked, see an

authorized dealer.

Maintenance Free Battery

IMPORTANT: Before you attach the battery cables to

the battery, check the battery date. The battery date

tells if the battery must be charged.

1. Raise the seat support (see Figure 2).

2. Remove two screws (1) and battery cover (2)

(see Figure 7).

3. Check the side of the battery (3) for the location of

the battery date.

a. If the battery is put into service before this

date, the battery cables can be attached

without charging the battery. See “Install the

Battery Cables.”

b. If the battery is put into service after this date,

the battery must be charged. See “Charge

the Battery.”

CHARGE THE BATTERY

1. Before you charge the battery (3), remove the

battery (see Figure 7).

2. To charge the battery, use a 12 volt battery charger.

Charge at a rate of 6 amps for 1 hour. If you do not

have a battery charger, have an authorized dealer

charge the battery.

3. Install the battery.

4. Connect the red cable (6) to the positive (+)

terminal using the fasteners (7). Place the terminal

boot (5) onto the positive terminal.

5. Connect the black cable (8) to the negative (-)

terminal with the fasteners (7).

6. Connect the battery retainer (4).

7. Install the battery cover (2) using two screws (1).

INSTALL THE BATTERY CABLES

1. Remove the protective caps from the battery

terminals (see Figure 7).

2. Slide the terminal boot (5) onto the red cable (6).

3. Connect the red cable (6) to the positive (+)

terminal with the fasteners (7). Place the terminal

boot (5) onto the positive terminal.

4. Connect the black cable (8) to the negative (-)

terminal with the fasteners (7).

5. Install the battery cover (2) with the two screws (1).

WARNING

When you charge the battery, do not smoke.

Keep the battery away from any sparks. The

fumes from the battery acid can cause an

explosion.

WARNING

To prevent sparks, fasten the red cable to the

positive (+) terminal before you connect the

negative (-) black cable.

WARNING

To prevent sparks, fasten the red cable to the

positive (+) terminal before you connect the

negative (-) black cable.

Not for

Reproduction

16

en

Assembly

WARNING

Follow the engine manufacturer’s instructions

for the type of fuel and oil to use. Always use a

safety fuel container. Do not smoke when

adding fuel to the engine. When inside an

enclosure, do not fill with fuel. Before you add

fuel, stop the engine. Let the engine cool for

several minutes.

Check the Tires

Check the air pressure in the tires. Tires with too much

air pressure will cause the unit to ride rough. Also, the

wrong air pressure will keep the mower deck from

cutting level. The correct air pressure is: Front Tires 1,0

BAR (14 PSI), Rear Tires 0,7 BAR (10 PSI). The tires

were over inflated for shipment.

Prepare the Engine

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil. Add oil as needed.

See the engine manufacturer’s instructions for the type

of fuel and oil to use. Before you use the unit, read the

information on safety, operation, maintenance,

and storage.

Assemble the Fuel Cap

The fuel cap will be shipped in the Parts Bag and tape

will be placed over the fuel tank opening during

shipment. Before operation, remove tape from opening

on fuel tank and install fuel cap.

Check the Level of the Mower Deck

Make sure the level of cut is still correct. After you mow

a short distance, look at the area that was cut. If the

mower deck does not cut level, see an

authorized dealer.

Not for

Reproduction

17

en

Features and Controls

LOCATION OF CONTROLS

Throttle Control Lever (1): Use the throttle control

lever to increase or decrease engine speed. Move the

throttle up to increase engine speed and down to

decrease engine speed. Always operate at

FULL throttle.

Clutch/Brake Pedal (2): The pedal has two functions.

The first function is a clutch. The second function is

abrake.

Ignition Switch (3): Use the ignition switch to start

and stop the engine. Never leave the ignition switch in

the RUN position with the engine stopped. This drains

the battery.

Parking Brake Knob (4): The parking brake knob is

used to lock the parking brake when the tractor is

stopped. Fully depress the brake pedal and pull up on

the knob to engage the parking brake.

Forward Speed Control Pedal (5): The tractor’s

forward ground speed is controlled by the forward

speed control pedal. Depress the pedal to increase

forward ground speed.

Reverse Speed Control Pedal (6): Use the reverse

ground speed pedal to control the reverse ground

speed of the tractor.

Lift Lever (7): The lift lever controls the mower cutting

height. There are six cutting height levels available (1 -

Lowest Cut, 6 - Highest Cut).

Blade Rotation Control (8): Use the blade rotation

control to start and stop the rotation of the blade. Pull

up on the switch to engage the blade rotation control

and push down to disengage.

Fuel Tank (9): To add fuel, remove the filler cap. Be

sure to leave room for heat expansion.

Grass Bagger Handle (10): The grass bagger handle

opens the bagger so that it can be emptied and closed

for mowing.

Seat Adjustment Lever (11): Pull up on the lever to

adjust the location of the seat. Release lever to lock

seat in place.

1

2

3

5

6

7

8

10

9

11

4

Not for

Reproduction

18

en

Operation

Start the Engine

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil. Add oil as needed.

See the engine manufacturer’s instructions for the type

of fuel and oil to use.

1. Push the clutch/brake pedal completely forward.

Keep your foot on the pedal.

2. Make sure the speed control pedal is in the

NEUTRAL position.

3. Make sure the blade rotation control is in the

DISENGAGE position.

4. Move the throttle control completely forward to the

CHOKE or FAST position.

5. Turn the ignition key to the START position

(see Figure 9).

NOTE: If the engine does not start after four or five

tries, move the throttle control to the FAST position.

Again try to start the engine. If the engine will not

start, see the TROUBLESHOOTING CHART.

6. Slowly move the throttle control to the

SLOW position.

7. To start a hot engine, move the throttle control to a

position between FAST and SLOW.

Before Starting the Engine

CHECK THE OIL

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil. Add oil as needed.

See the engine manufacturer’s instructions for the type

of fuel and oil to use.

1. Make sure the unit is level.

NOTE: Do not check the level of the oil while the

engine runs.

2. Check the oil. Follow the procedure in the engine

manufacturer’s instructions.

3. If necessary, add oil until the oil reaches the FULL

mark on the dipstick. Do not add too much oil.

ADD FUEL

1. Remove the filler cap (1) (see Figure 8).

2. Fill the fuel tank (2) to the FULL (3) position with

regular unleaded fuel.

NOTE: Do not use premium unleaded fuel. Make

sure the fuel is fresh and clean. Leaded fuel will

increase deposits and shorten the life of the valves.

WARNING

Always use a safety fuel container. Do not

smoke when adding fuel to the fuel tank. Do

not add fuel when you are inside an enclosure.

Before you add fuel, stop the engine and let the

engine cool for several minutes.

WARNING

The electrical system has an operator

presence system that includes a sensor switch

for the seat. These components tell the

electrical system if the operator is sitting on

the seat. This system will stop the engine when

the operator leaves the seat. For your

protection, always make sure this system

operates correctly.

Important! Before You Start Mowing

• Check the engine oil.

• Fill the fuel tank with fuel.

• Check the air pressure of the tires.

• Check the level of the mower housing.

• Attach the battery cables.

Not for

Reproduction

19

en

Operation

Use the Throttle Control

Use the throttle control to increase or decrease the

speed of the engine.

1. Move the throttle/choke control completely forward

to the CHOKE position to start a cold engine

(see Figure 10).

2. The FAST position is marked with a detent. For

normal operation and when using a grass bagger,

move the throttle control to the FAST position. For

maximum charging of the battery and for a cooler

running engine, operate the engine in the

FAST position.

3. The engine governor is set at the factory for

maximum performance. Do not adjust the governor

to increase the speed of the engine.

Use the Blade Rotation Control

Use the blade rotation control to engage the blade(s).

1. Before you start the engine, make sure the blade

rotation control is in the DISENGAGE position

(see Figure 11).

2. To engage the blade, pull the blade rotation control

upward to the ENGAGE position.

NOTE: This model is equipped with a bag full

indicator. With the blade rotation control engaged, a

buzzer will sound when the bag is full.

3. To stop the blade, move the blade rotation control

to the DISENGAGE position. Before you leave the

operator’s position, make sure the blade(s) has

stopped rotating.

4. Before you ride the unit across a sidewalk or a

road, move the blade rotation control to the

DISENGAGE position.

WARNING

Always keep your hands and feet away from

the blade, deflector opening, and the mower

deck when the engine runs.

Attachments

See an authorized dealer for a list of the available

attachments.

Install the Mulcher Cover

The mulcher cover lets you mulch the grass for a clean,

fine cut. Install as follows.

1. Follow the steps shown in Figure 12 to remove the

rear discharge chute and chute extension.

2. Mount the mulcher cover (1) to the mower deck with

the bolts (4), washers (2), and flange locknuts (3)

(see Figure 13).

3. For mulching operation, install mulch blade as an

accessory part. See authorized dealer.

Use the Speed Control Pedals

The drive system uses a Hydrostatic Automatic Drive

Transmission. The hydrostatic transmission is very easy

to operate. This type of drive system does not require a

shift lever or a clutch pedal.

The speed and direction of travel is controlled by a

forward speed control pedal and reverse speed control

pedal operated with your right foot.

NOTE: Do not use the brake pedal in normal operation.

Only use the brake pedal to quickly stop in

an emergency.

DRIVE FORWARD

1. The automatic drive disconnect must be in the

DRIVE position (see A, Figure 14).

2. Slowly release your foot from the brake pedal

(see Figure 15).

3. Move the throttle control to the FAST position

(see Figure 10).

4. Slowly push the forward speed control pedal (1) to

enable forward ground speed (see Figure 16).

5. To increase forward speed, slowly push down on the

forward speed control pedal. To reduce forward

speed, slowly release the forward speed control

pedal until the unit slows to the desired speed.

Not for

Reproduction

20

en

Operation

DRIVE IN REVERSE

1. Before driving in reverse, look to the rear. Look

behind and down for small children to

ensure safety.

2. Remove your foot from the forward speed control

pedal (1) (see Figure 16).

3. Slowly push the reverse speed control pedal (2) to

enable reverse ground speed.

4. To increase reverse speed, slowly push down on

the reverse speed control pedal. To reduce reverse

speed, release the reverse control pedal until the

unit slows to the desired speed.

CHANGE DIRECTIONS

CAUTION: To change directions, do not use the

brake pedal. Use only the speed control pedals.

1. Slowly remove your foot from the forward speed

control pedal (1) or reverse speed control pedal (2)

(see Figure 16). The forward speed control pedal or

reverse speed control pedal will automatically

return to the NEUTRAL position.

2. When the unit stops, slowly move the forward

speed control pedal or reverse speed control pedal

to the desired direction.

Disconnect the Transmission

To push the unit, use the automatic drive disconnect to

release the transmission. The automatic drive

disconnect is located near the right rear tire.

1. The engine must be off.

2. Move and latch the automatic drive disconnect in

the PUSH position (see B, Figure 14). The

transmission is now released and the unit can

be pushed.

NOTE: In cold weather, the heavy viscosity oil in the

transmission will make the unit difficult to push.

3. To engage the transmission, unlatch and push-in

the automatic drive disconnect. The transmission is

now connected and ready to operate.

Use the Parking Brake

1. Fully depress the clutch/brake pedal

(see Figure 15).

2. Pull up the parking brake knob (Figure 17).

3. Remove your foot from the clutch/brake pedal and

then release the parking brake knob. Make sure the

parking brake will hold the unit.

4. To release the parking brake, fully depress the

clutch/brake pedal. The parking brake will

automatically release.

Change the Cutting Height

To change the cutting height, raise or lower the lift lever

as follows.

1. Move the lift lever forward to lower the mower deck

and back to raise the mower deck (see Figure 18).

2. When you ride on a sidewalk or road, move the lift

lever to the highest position and move the blade

rotation control to the DISENGAGE position

(see Figure 11).

Empty the Grass Bagger

1. Extend the grass bagger handle and rotate forward

until the grass bagger assembly is completely open

at the bottom (see Figure 19).

2. Empty the grass from the bagger.

3. Rotate the grass bagger assembly back to the

closed position for mowing.

WARNING

Before you leave the operator’s position,

release the speed control pedal. Set the

parking brake. Move the blade rotation control

to the DISENGAGE position. Stop the engine

and remove the ignition key.

Not for

Reproduction

La pagina sta caricando ...

Simplicity SNAPPER PREMIUM RIDER, LT75 15,5/17,5 CE Manuale utente

Questo manuale è adatto anche per

Simplicity SNAPPER PREMIUM RIDER, LT75 15,5/17,5 CE Manuale utente

in altre lingue

Documenti correlati

Altri documenti