Panasonic KX-TCD705BX Operating Instructions Manual

Categoria
Telefoni
Tipo
Operating Instructions Manual
Digital Cordless Phone
Model No. KX-TCD705BX
Operating Instructions
Charge the batteries for approx. 10 hours before initial use.
Caller ID Compatible
PLEASE READ BEFORE USE AND SAVE
KX-TCD705BX 12/7/01 2:28 pm Page 1
2
Dear purchaser,
You have acquired a KX-TCD705BX, which is a product made in regard with the
European Standards for Cordless Telephones (DECT). DECT technology is
characterized by high-security protection against interceptions as well as high-quality
digital transmission.
This telephone was designed for a wide range of applications.
For example, this telephone can be used within a network of base units and handsets,
constituting a telephone system which:
operates up to 6 handsets at one base unit
allows an intercom between handsets
allows the operation of a handset at up to 4 base units, expanding the
communication radio area.
This telephone may be used for:
operating several handsets
operating at several base units
connecting the base unit to a PBX.
AC Adaptor
one
Telephone Line Cord
one
Batteries
Panasonic AA(R6)P-6P or BYD
N4DH33B00001
two (AA size)
Battery Cover
one
Belt Clip
one
Operating Instructions
one
Thank you for purchasing your new Panasonic digital cordless telephone.
For your future reference
Serial No. Date of purchase
(found on the bottom of the unit)
Name and address of dealer
Accessories include
KX-TCD705BX 12/7/01 2:28 pm Page 2
3
Safety Instructions
Take special care to follow the safety suggestions listed below.
Safety
1) The unit should be connected to a power supply only of the type described in the
operating instructions or as marked on the unit.
2) When the unit is not used, turn the power off. When left unused for a long period of
time, the base unit should be unplugged from the household AC outlet.
Installations
Environment
1) Do not use this unit near water—for example, near a bathtub, washbowl, sink, etc.
Damp basements should also be avoided.
2) The unit should be kept away from heat sources such as radiators, cookers, etc. It also
should not be placed in rooms where the temperature is less than 5°C or greater than
40°C.
3) The AC adaptor is used as the main disconnect device, ensure that the AC outlet is
located/installed near the unit and is easily accessible.
Placement
1) Do not place heavy objects on top of this unit.
2) Care should be taken so that objects do not fall onto, and liquids are not spilled into,
the unit. Do not subject this unit to excessive smoke, dust, mechanical vibration or
shock.
3) Place the unit on a flat surface.
For best performance
1) If noise prevents the conversation from being understood at the handset, move toward
the base unit to reduce the noise.
2) The handset should be used at the HIGH volume setting when it is difficult to hear the
other party.
3) The handset should be fully recharged on the base unit when “Û” on the display
flashes.
4) The maximum calling distance may be shortened when the unit is used in the following
places: Near obstacles such as hills, tunnels, underground, near metal objects such as
wire fences etc.
Lightning Surge
This unit has already been equipped with a built-in lightning protection circuit. However,
we recommend that you install the following options, if your area has frequent lightning
strikes.
1) Lightning protection on the telephone line.
2) Lightning protection on the power source.
To install the above options, please contact your local sales shop.
Lightning damage is not covered in the warranty even if lightning protection is installed.
KX-TCD705BX 12/7/01 2:28 pm Page 3
Contents
4
Chapter 1
Preparation
Chapter 3
Programmable Functions
(On the Handset)
Chapter 2
Basic Operations
Handset Programming........................37
Setting Alarm .......................................37
Setting Ringer Options .......................37
Select Handset Ringer Volume........37
Select Ringer Patterns.....................37
Setting Tone Options ..........................38
Setting Display Options......................38
Select the Standby Mode Display ...38
Select the Talk Mode Display ..........38
Setting Call Options ............................38
Set Direct Call Number....................38
Set Direct Call ON/OFF...................38
Select Call Prohibition .....................38
Setting Other Options ...................39
Set Auto Talk ON/OFF.....................39
Select Battery Type .........................39
Select Handset PIN .........................39
Registration..........................................39
Registering a Handset to a
Base Unit .........................................39
Cancelling a Base Unit ....................39
Select Base Unit ..................................39
Reset Handset .....................................39
Making Calls ........................................13
Auto Redial ..........................................15
To Select the Receiver/Speaker
Volume..................................................15
Direct Call.............................................16
Answering Calls ..................................17
Using the Phonebook ........................18
Storing Names and Numbers in the
Phonebook ...........................................19
Finding Items in the Phonebook......22
Dialling from the Phonebook ...........22
Editing an Item in the Phonebook ...23
Phonebook Copy .............................24
Storing Phonebook Items as Hot
Key Dials..........................................26
Dialling a Stored Number ................26
Clearing an Item in the Hot Key Dial .27
Caller ID Service ..................................28
Using the Caller List............................29
Paging/Intercom ..................................32
For Optional Multi-Unit Users ............34
Special Features..................................35
How to Use the Pause Feature
(For Analog PBX Line/Long
Distance Service Users)..................35
Using the Recall Feature.................35
Temporary Tone Dialling ..................36
Setting the Key Lock ON/OFF.........36
Getting Started .....................................6
Connections ......................................6
Installing the Batteries in the
Handset .............................................7
Battery Charge...................................7
Battery Information ............................7
Battery Replacement .........................8
Base Unit Location ............................8
Wall Mounting ....................................9
Location of Controls.........................10
Displays..............................................11
Basic Start-up Operations................12
KX-TCD705BX 12/7/01 2:28 pm Page 4
5
Chapter 4
Programmable Functions
(On the Base Unit)
Base Programming .............................43
Bell Selection.......................................43
Select Base Unit Ringer Volume........44
Select the Dialling Mode.....................44
Select Earth/Flash Timing ..................45
Select Pause Timing ...........................45
Set Base Unit PIN ................................44
Cancelling a Handset ..........................46
Setting the Clock .................................46
Setting the Date ...................................46
Reset Base Unit ...................................46
Using an Optional Headset.................47
Using the Belt Clip...............................47
Option Covers......................................48
Before Requesting Help......................49
Adding another phone.........................51
Chapter 5
Useful Information
KX-TCD705BX 12/7/01 2:28 pm Page 5
6
Connections
Plug in the AC Adaptor and the telephone line cord to the rear of the unit. Then connect
the cord as shown.
Getting Started
USE ONLY WITH Panasonic AC ADAPTOR PQLV1CE.
The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel
warm during use).
If your unit is connected to a Telephone line or PBX which does not support Caller ID
services, you cannot access those services.
The telephone will not work during a power failure. We therefore recommend you
connect a standard telephone on the same line for power protection.
KX-TCD705BX 12/7/01 2:28 pm Page 6
LINE
Fasten the AC adaptor cord
to prevent it from being
disconnected
Hook
9v
To Mains Outlet
(AC 220-240V, 50Hz)
AC Adaptor
Telephone Line Cord
To Telephone Socket
Fasten the AC adaptor
cord to prevent it from
being disconnected
7
Installing the Batteries in the Handset
Battery Strength
You can check the present battery
strength on the display.
Recharge
When “Û” flashes or the unit beeps every 15 seconds, recharge the batteries.
Chapter 1
Battery Information
After your batteries are fully charged:
Battery life may vary depending on usage conditions, such as:
when viewing the Caller ID Caller List,
when talking in the speakerphone mode, or using headset, and
ambient temperature.
Clean the handset charge contacts with a soft, dry cloth once a month. Clean
more often if the unit is subject to grease, dust or high humidity. Otherwise the
batteries may not charge properly.
If the batteries are fully charged, you do not have to place the handset on the base unit
until “Û” flashes. This will maximise the battery life.
The batteries cannot be overcharged.
Operation Ni-MH battery life (Included) Ni-Cd battery life (optional)
While in use (Talk) Up to about 20 hours Up to about 12 hours (based on 800m/A per hour)
While not in use (Standby) Up to about 160 hours Up to about 100 hours
Battery Charge
At the time of shipment, the batteries are not
charged. To charge, place the handset on the
base unit. Please charge the batteries for
approximately 10 hours before initial use.
During charging, the battery icon is as shown.
Low
Flashing
Full
Battery strength Fully charged Medium Low No power
Battery icon
Ò
Ú
Û
(Flashing)
Û
If the
rechargeable
batteries are not
inserted correctly,
the handset will
not work.
KX-TCD705BX 12/7/01 2:28 pm Page 7
8
Battery Caution:
To reduce the risk of fire or injury to persons, read and follow these instructions.
1. Use only the batteries specified.
2. Do not use non-rechargeable batteries.
3. Do not mix old and new batteries.
4. Do not dispose of the batteries in a fire, they may explode. Check with local waste
management codes for special disposal instructions.
5. Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause
burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.
6. Exercise care in handling the batteries in order not to short the batteries with
conductive materials such as rings, bracelets, and keys. The batteries and/or
conductor may overheat and cause burns.
7. Charge the batteries provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.
Getting Started
Battery Replacement
If Û flashes after a few telephone calls even when the handset batteries have been
fully charged, it is time to replace the batteries with new ones. Remember to charge the
new batteries after replacement (see page 7).
Discard defective batteries as soon as possible. Defective batteries may leak into
the unit.
On replacing the batteries, ensure that the correct battery type selection is
programmed (see page 39).
For maximum distance and noise-free operation, the recommended base unit location
is:
Away from electrical appliances such as TV, radio, personal computer or another
telephone.
In a convenient high and central location.
Base Unit Location
KX-TCD705BX 12/7/01 2:28 pm Page 8
9
Wall Mounting
This unit can be mounted on a wall.
Install screws using the wall template below.
Connect the line cord, and AC Adaptor.
Arrange the wires as shown, then mount the unit.
6cm
6cm
WALL TEMPLATE
KX-TCD705BX 12/7/01 2:28 pm Page 9
Location of Controls
Base Unit
Handset
10
7
1
0
3
2
4
6
8
9
5
Charge Contacts
Page Button
KX-TCD705BX 12/7/01 2:28 pm Page 10
Icons
Î The in-range icon indicates that
the handset is in range of the base
unit. It flashes when the handset is
out of range.
Ï The page/intercom icon is
displayed when paging or using
the intercom. It flashes when
another unit pages the handset.
The talk icon is displayed when
making or answering calls. It
flashes when an external call is
being received.
Ô The call prohibition icon is
displayed when this mode is turned
on.
Á The phonebook icon is displayed
when storing or viewing the
phonebook items.
Ò The battery icon indicates the
battery strength.
Displays
11
P Pauseis selected while dialling.
The direct call icon is displayed when
this mode is turned on.
F M is pressed while dialling.
[X] The key lock icon is displayed when
key lock is set on the handset. In this
mode, the keypad is disabled.
ABCDEFGHIabcdefg
1234567890123456
ÎÏÔÍ Á Ò
Characters/Symbols
Display Backlight
The handset has a backlight display. The display will light when you start using the
handset and when a call is received. The handset display light will stay on for about 10
seconds after pressing a button or lifting the handset off the base unit. You can change
the backlight colour for identifying callers by setting the private category feature (page18).
Lighted Handset Keypad
The handset dialling buttons will light when you press a button, lift the handset off the
base unit or receive a call. The lights will go out about 10 seconds after pressing a button,
lifting the handset or answering a call.
Handset Display
KX-TCD705BX 12/7/01 2:28 pm Page 11
Making a Call
(For further information on making calls, see pages 13-16)
1. ZO or %.
2. Dial a phone number.
The dialled number is displayed.
(If a number is entered incorrectly, ZP).
After a few seconds, the display will start showing the length of the call.
12
Terminating a Call
1. To hang up, ZP.
After a few seconds, the display returns to the standby mode.
If the handset is placed on the base or charger during a call, the call is
disconnected.
The dialled number is stored in the redial memory.
Turning the Power On
1. Z and hold P
A confirmation tone sounds.
All possible configurations briefly appear.
When button is released, the display will change to the standby mode.
The current connected base unit number is displayed
You can choose whether to display the base unit number, handset number or no
display in the standby mode (see page 38).
The number of New Caller ID calls received are displayed.
Basic Start-up Operations
Answering a Call
(For further information on answering calls, see page 17.)
During Incoming call:
1. ZO
You can also answer a call by pressing any dialling button K to I, $, L
or N (-Any Key Answer).
Or Z%and when the other party answers, talk into the microphone.
After a few seconds, the display will start showing the length of the call.
Turning the Power Off
Make sure that the unit is in the standby mode.
1. Z and hold P until a long beep sounds.
The display will go blank. (On location of the handset in the base unit, the battery
icon will display even after power off).
Base 1
10 New Calls
Î ÏÔÍ Á Ò
Note: Z shows that you should press the following key(s).
KX-TCD705BX 12/7/01 2:28 pm Page 12
Making Calls
13
Note: for basic making calls operation, see page 12.
To Dial after Confirming the Entered Number
With this feature you are able to confirm the entered number before you start dialling.
1. Enter a phone number (maximum 24 digits)
If number is not entered correctly:
To clear one digit, ZWbriefly.
To clear all digits, Z and hold W.
2. Phone number confirmed, ZO or %.
(After a few seconds, the display will start showing the length of the
call).
3. To end call, ZP.
(After a few seconds, the display returns to the standby mode).
Note: If Î flashes and an error tone sounds after pressing O or %,
move closer to the base unit. Then try again.
You can choose whether to display the length of the call or phone number in the talk
mode by programming (page 38).
To Have a Hands-Free Phone Conversation (Using
Digital Speakerphone)
1. Z%
The button lights.
2. Enter a phone number.
The dialled number is displayed.
3. When the other party answers, talk into the microphone.
4. To hang up, ZP.
Chapter 2
ABCDEFGHIabcdefg
0123456789012345
Î ÏÔÍ Á Ò
ABCDEFGHIabcdefg
0123456789012345
Î Ï ÔÍ Á Ò
ABCDEFGHIabcdefg
00-00-31
Î Ï ÔÍ Á Ò
Base 1
A2 New calls
A03.08.21:06
Î ÏÔÍ Á Ò
Handset Digital Speakerphone
For best performance, please note the following:
Talk alternately with the caller in a quiet room.
If the other party has difficulty hearing you, ZUor S to decrease or increase
the speaker volume.
If the other partys voice from the speaker cuts in/out during a conversation, ZU
to decrease the speaker volume.
While talking, you can switch to the hands-free phone conversation by pressing %.
To switch back to the receiver, Z%or O.
KX-TCD705BX 12/7/01 2:28 pm Page 13
Making Calls
To Redial the Last Number Dialled
There are two ways to redial the last number dialled.
1. ZO or %.
2. ZX.
(The last number dialled is displayed and automatically redialled).
After a few seconds, the length of call is displayed.
OR
1. ZOor %.
2. ZY
3. Select Redial.
4. ZY
(The last number dialled is displayed and automatically redialled).
To Redial after Confirming the Numbers in Redial Memory
The unit automatically stores the last 10 numbers dialled into redial memory.
1. ZX.
(The last number dialled is displayed).
If the same number has been stored in the phonebook, the name
will also be displayed.
2. ZSor U to select required number
(To exit the list, ZW).
3. ZOor %.
The number is redialled automatically.
(After a few seconds the length of call is displayed).
If a number is not selected within one minute, redial mode is
cancelled and display returns to standby mode.
If No Stored Memoryis displayed in step 1, the redial memory
is empty.
To Edit/Clear Numbers in the Redial List
To edit and clear numbers in the redial memory, ZX, select number and then follow
from step 2 (pages 30 and 31). Editing the Callers Name / Phone Number, To Clear an
Individual Entry in the Caller ID Listand To Clear All Entries in the Caller ID List.
14
ABCDEFGHIabcdefg
01234567890
Î Ï ÔÍ Á Ò
ABCDEFGHIabcdefg
00-00-00
Î Ï ÔÍ Á Ò
ABCDEFGHIabcdefg
01234567890
Î Ï ÔÍ Á Ò
ABCDEFGHIabcdefg
00-00-00
Î Ï ÔÍ Á Ò
KX-TCD705BX 12/7/01 2:28 pm Page 14
Auto Redial
When speakerphone is turned on and redial used, the number is dialled automatically. If
the number is busy, the unit goes into auto redial mode. The unit automatically repeats the
call (max. 12 times) until the called party answers the call.
Make sure that the unit is in the standby mode.
1. Z%.
2. ZX.
The last redial number is displayed and dialled to outside line.
The Mic on handset is mute until a busy toneor ring back tone
is detected.
If a busy tone is detected, the unit releases the outside line and returns to the standby
mode. The speakerphone button LED flashes. After 40 seconds, the speakerphone
LED turns steady on and the number is redialled automatically.
If a ring back tone is detected, the mic is not mute, –Muting– is cleared from the 1st
line, the unit finishes Auto Redial and display goes to conversation.
If the user presses % during Auto Redial, redial is cancelled and unit returns to
speakerphone.
If a busy tone or ring back tone is not detected within 30 seconds, the unit finishes
Auto Redial procedure and unit returns to standby.
To Select the Receiver Volume or Speaker Volume
during conversation
3 levels are available during conversation or when using the headset (high, medium or
low).
6 levels are available in the speakerphone mode.
1. During conversation, ZSor U to select level
S = receiver volume up
U = receiver volume down.
After a few seconds, the display returns to the length of call.
15
–Muting–
0223456789
Î Ï ÔÍ Á Ò
Receiver Volume
LOW HIGH
ASetting Base
Î Ï ÔÍ Á Ò
KX-TCD705BX 12/7/01 2:28 pm Page 15
Making Calls
Direct Call
You can store one number into memory and then call this number by pressing O or %.
(See pages 38, 40).
Hot Key Dialling
You can assign up to 9 numbers from the phonebook as Hot Key Dials. After numbers
have been stored (see page 26) you can press buttons A to I and then ZOor
% to call the number.
Dialling a Number from the Phonebook or Caller ID List
Dialling a number from the Phonebook (see page 22).
Dialling a number from the Caller ID List (see page 30).
16
KX-TCD705BX 12/7/01 2:28 pm Page 16
Answering Calls
For basic answering call operation, see page 12.
The handset and base unit will not ring if both ringer volumes are set to OFF
(pages 37, 44).
Auto Talk
If you set the Auto Talk Feature to ON (page 39), you can answer a call by lifting the
handset off the base unit without pressing O or %.
To Turn the Handset Ringer Off Temporarily
When an external call is incoming, user can turn off ringer temporarily.
1. During incoming call, Z and hold U.
(Ringer Offis displayed and the handset stops ringing).
2. Answer call by pressing O, K-I, $, L or N
(-Any Key Answer).
The ringer will turn back on for the next call.
This function will not work when the handset is on the base unit or
if an internal call is incoming
If Ringer Offis selected, Caller ID cannot be displayed.
17
Ringer Off
ASetting H/set
ASetting Base
Î Ï
ÔÍ
Ò
ABCDEFGHIabcdefg
00-00-00
Î Ï ÔÍ Á Ò
KX-TCD705BX 12/7/01 2:28 pm Page 17
Using the Phonebook
You can store up to 200 names and phone numbers in the phonebook. All phonebook
items are sorted by the first word in alphabetical order. Using the phonebook, you can
make a call by selecting a name on the display.
You can also assign the callers information to one of 9 private categories (1-9) to use the
private category feature (page 19). This feature is only available after subscribing to
Caller ID.
Private category feature:
You can select display backlight colour and ringer type for each private category. When
receiving a call, you can easily figure out who has called. (For example, Category 1 for
family, Category 2 for friends and Category 9 for business).
When a call is received from the caller belonging to one of the private categories, the
handset will ring with the selected ringer type and the display will light in the selected
colour for each private category. If you do not assign an item to any private category
number, the handset will ring in the preset ringer type and light in the preset colour when
receiving a call.
Entry example:
Example:
When receiving a call from a caller belonging to category 1;
the handset rings in the ringer type 1.
the display backlight lights in red.
When receiving a call, selected ringer type and display backlight colour are determined
by the following order: Private category feature and then the pre-selected colour and
ringer type.
18
Phonebook items
Backlight colour Ringer type
Private category no. (1-9)
(3 colours) (1-20)
1: Family Red 1
2: Friends Orange 2
3: Neighbours Green 3
:::
9: Business Red 20
OFF Pre-selected colour Pre-selected type
Phone
numbers
and
names (up
to 200)
KX-TCD705BX 12/7/01 2:28 pm Page 18
Storing Names and Numbers in the Phonebook
Make sure that the unit is in the standby mode.
1. ZYor V.
2. Select ‘New Phonebook’.
3. ZYor V.
The display shows the number of remaining phonebook items,
then <Enter Name>.
4. Enter a name (up to 16 characters) with the dialling buttons, T
or V.
See steps for entering names and symbols (page 21).
5. Name confirmed ZU.
6. Enter phone number (up to 24 digits).
7. Number confirmed, ZY.
8. ZUor S to select Private Category number (1-9) or OFF.
9. ZYor V.
10. Select ‘Save’.
11. ZYor V.
A beep sounds and Savedis displayed.
The display shows the number of remaining phonebook items,
then <Enter Name>. You can continue storing other items.
To return to the standby mode, ZP.
If a pause is required for dialling,ZX. If a pause is inserted
while entering a phone number, the pause counts as one digit.
If the display shows Memory Fullin step 3, the display will
return to the standby mode. To store, clear other stored items in
the phonebook (page 23).
You can exit the programming mode at any time by pressing P.
19
Base 1
A2 New Calls
A03.08 21:06
Î ÏÔÍ Á Ò
New Phonebook
ASetting Handset
ASetting Base
Î ÏÔÍ Á Ò
Enter
New Phonebook
200-Memory Avail
Î ÏÔÍ ÁÒ
<Enter Name>
ASetting H/set
ASetting Base
Î ÏÔÍ ÁÒ
JAMES
<Enter Phone No>
ASetting Base
Î ÏÔÍ ÁÒ
JAMES
<Enter Phone No>
ASetting Base
Î ÏÔÍ ÁÒ
JAMES
01234567
ASetting Base
Î ÏÔÍ ÁÒ
JAMES
01234567
****Saved****
Î ÏÔÍ ÁÒ
Private Category
OFF
ACategory 1
Î ÏÔÍ ÁÒ
Save
AGo Back
ASetting Base
Î ÏÔÍ ÁÒ
KX-TCD705BX 12/7/01 2:28 pm Page 19
To Enter Names Selecting Characters
The dialling buttons can be used to enter letters and character symbols. The letters are
printed on the dialing buttons. Pressing each button selects a character as shown on
page 21.
To change the character mode
You can select one of 6 character modes by pressing Á during entering a name.
The factory preset is ABC.
1. while entering a name.
2. ZUor S until the arrow points to the desired character
mode, then ZYor V.
The character mode is displayed.
For example, to enter ‘Anne’.
1. ZB.
2. Z$, then F TWICE.
3. ZV, then F TWICE.
4. ZCTWICE.
If you make a mistake while entering a Name/Number
ZSor U to move between Namearea and Phone Numberarea.
ZTor V to move cursor to required position.
To delete one number/letter, ZW. (Items are deleted to the left of the cursor).
To delete all numbers/letters, Z and hold W.
To add a number/letter, move cursor to required position. Press number/letter. The item
is added to the left of the cursor.
Anne
Ann
A
> <Enter Name>
ASetting H/set
ASetting Base
Î ÏÔÍ ÁÒ
Using the Phonebook
20
ABC
A0-9
AABΓ
Î ÏÔÍ ÁÒ
AÄÅ
ASŚŠ
AAБВ
Î ÏÔÍ ÁÒ
An
KX-TCD705BX 12/7/01 2:28 pm Page 20
1 / 1

Panasonic KX-TCD705BX Operating Instructions Manual

Categoria
Telefoni
Tipo
Operating Instructions Manual

in altre lingue