Cisco DPC3939 XFINITY Manuale del proprietario

OL- 29163-01

Cisco Model DPC3939 DOCSIS 3.0

16x4 Wireless Residential Voice

Gateway

User Guide

Please Read

Important

Read this entire guide. If this guide provides installation or operation instructions,

give particular attention to all safety statements included in this guide.

Notices

Trademark Acknowledgments

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its

affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this

URL: www.cisco.com/go/trademarks. DOCSIS is a registered trademark of Cable

Television Laboratories, Inc. EuroDOCSIS, EuroPacketCable, and PacketCable are

trademarks of Cable Television Laboratories, Inc. The Wi-Fi Protected Setup mark is

a mark of the Wi-Fi Alliance. Wi-Fi Protected Setup is a trademark of the Wi-Fi

Alliance.

Other third party trademarks mentioned are the property of their respective owners.

The use of the word partner does not imply a partnership relationship between

Cisco and any other company. (1110R)

Publication Disclaimer

Cisco Systems, Inc. assumes no responsibility for errors or omissions that may

appear in this publication. We reserve the right to change this publication at any

time without notice. This document is not to be construed as conferring by

implication, estoppel, or otherwise any license or right under any copyright or

patent, whether or not the use of any information in this document employs an

invention claimed in any existing or later issued patent.

Disclaimer

The maximum performance for wireless is derived from IEEE Standard 802.11

specifications. Actual performance can vary, including lower wireless network

capacity, data throughput rate, range and coverage. Performance depends on many

factors, conditions and variables, including distance from the access point, volume of

network traffic, building materials and construction, operating system used, mix of

wireless products used, interference and other adverse conditions.

Software and Firmware Use

The software described in this document is protected by copyright law and

furnished to you under a license agreement. You may only use or copy this software

in accordance with the terms of your license agreement.

The firmware in this equipment is protected by copyright law. You may only use the

firmware in the equipment in which it is provided. Any reproduction or distribution

of this firmware, or any portion of it, without our express written consent is

prohibited.

Copyright

Information in this publication is subject to change without notice. No part of this

publication may be reproduced or transmitted in any form, by photocopy,

microfilm, xerography, or any other means, or incorporated into any information

retrieval system, electronic or mechanical, for any purpose, without the express

permission of Cisco Systems, Inc.

Notice to Installers

The servicing instructions in this notice are for use by qualified service personnel only. To reduce the

risk of electric shock, do not perform any servicing other than that contained in the operating

instructions, unless you are qualified to do so.

Notice à l’attention des installateurs de réseaux câblés

Les instructions relatives aux interventions d’entretien, fournies dans la présente notice, s’adressent

exclusivement au personnel technique qualifié. Pour réduire les risques de chocs électriques, n’effectuer

aucune intervention autre que celles décrites dans le mode d'emploi et les instructions relatives au

fonctionnement, à moins que vous ne soyez qualifié pour ce faire.

Mitteilung für CATV-Techniker

Die in dieser Mitteilung aufgeführten Wartungsanweisungen sind ausschließlich für qualifiziertes

Fachpersonal bestimmt. Um die Gefahr eines elektrischen Schlags zu reduzieren, sollten Sie keine

Wartungsarbeiten durchführen, die nicht ausdrücklich in der Bedienungsanleitung aufgeführt sind,

außer Sie sind zur Durchführung solcher Arbeiten qualifiziert.

Aviso a los instaladores de sistemas CATV

Las instrucciones de reparación contenidas en el presente aviso son para uso exclusivo por parte de

personal de mantenimiento cualificado. Con el fin de reducir el riesgo de descarga eléctrica, no realice

ninguna otra operación de reparación distinta a las contenidas en las instrucciones de funcionamiento, a

menos que posea la cualificación necesaria para hacerlo.

20080814_Installer820_Intl

OL-29163-01 iii

Contents

IMPORTANT SAFETY INSTRUCTIONS v

United States FCC Compliance xi

CE Compliance xiii

About This Guide xv

Chapter 1 Introducing the Residential Gateway 1

Introduction ......................................................................................................................... 2

What's In the Carto n? .......................................................................................................... 4

Front Panel Description ...................................................................................................... 5

Top Panel Description......................................................................................................... 7

Bottom Panel Description ................................................................................................... 8

Back Panel Description ....................................................................................................... 9

Chapter 2 Installing the Residential Gateway 11

Installation Preparations ................................................................................................... 12

Install the Resid ential Gateway........................................................................................ 17

Install the Battery .............................................................................................................. 20

MoCA Installation Guidelines ......................................................................................... 22

Chapter 3 Configuring the Residential Gateway 25

Configure Wireless Settings ............................................................................................. 26

Chapter 4 Operation of Front Panel Indicators 37

Initial Power Up, Calibration, and Registration (AC Power applied) ........................... 38

Normal Op erations (AC Power Applied) ....................................................................... 40

Special Conditions ............................................................................................................. 41

Contents

iv OL-29163-01

Chapter 5 Maintaining the Battery 43

Location of the Battery ...................................................................................................... 44

Battery Mai ntenanc e ......................................................................................................... 45

Chapter 6 Troubleshooting the Residential Gateway 47

Frequently Asked Questio ns ............................................................................................ 48

Common Troubles hooting Issues .................................................................................... 54

Tips for Improved Performa nce ....................................................................................... 56

Chapter 7 Customer Information 57

IMPORTANT SAFETY INSTRUCTIONS

OL-29163-01 v

IMPORTANT SAFETY INSTRUCTIONS

1)

Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4)

Follow all instructions.

5)

Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's

instructions.

8) Do not install near any h

eat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding-type

plug has two blades and a third grounding prong. The wide blade or the third

prong is provided for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10)

Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12)

Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from

tip-over.

13)

Unplug this apparatus during lightning storms or when unused for long periods of

time.

14)

Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as a power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

Power Source Warning

A label on this product indicates the correct power source for this product. Operate this product only

from an electrical outlet with the voltage and frequency indicated on the product label. If you are

uncertain of the type of power supply to your home or business, consult your service provider or your

local power company.

The AC inlet on the unit must remain accessible and operable at all times.

Ground the Product

WARNING: Avoid e lectric shock and fire haza r d! If this product connects to coaxial

cable wiring, be sure the cable system is grounded (earthed). Grounding provides

some protection against voltage surges and built-up static charges.

IMPORTANT SAFETY INSTRUCTIONS

vi OL-29163-01

Outdoor Grounding System

If this product connects to an outdoor antenna or cable system, be sure the antenna or cable system is

grounded (earthed). This provides some protection against voltage surges and built-up static charges.

Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990, provides the following

information:



Grounding of the mast and supporting structure



Grounding the lead-in wire to an antenna discharge unit



Size of the grounding conductors



Location of the antenna-discharge unit



Connection to grounding electrodes



Requirements for the grounding electrodes (see the following antenna grounding diagram as

recommended by NEC ANSI/NFPA 70)

WARNING: Avoid electric shock a nd fir e hazard! Do not locate an outside antenna

system in the vicinity of overhead power lines or power circuits. Touching power lines

or circuits might be fatal.

Protect the Product from Lightning

In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.

Verify the Power Source from the On/Off Power Light

When the on/off power light is not illuminated, the apparatus may still be connected to the power

source. The light may go out when the apparatus is turned off, regardless of whether it is still plugged

into an AC power source.

IMPORTANT SAFETY INSTRUCTIONS

OL-29163-01 vii

Eliminate AC Power/Mains Overloads

WARNING: Avoid ele ctr ic shock and f ire hazar d! Do not overload AC pow er/mains,

outlets, extension cords, or integral convenience receptacles. For products that require

battery power or other power sources to operate them, refer to the operating

instr uctions for those products.

Handling Disposable Batteries

This product may contain a rechargeable Lithium-Ion battery to provide stand-by operation in the

event of an AC power failure.

Heed the following warning, follow the Battery Safety and Battery Disposal instructions below, and see

the instructions later in this guide for handling, replacing, and disposing of the battery.

WARNING: There is danger of explosion if the battery is mishandled or incorrectly

replaced. Replace only with the same type of battery. Do not disassemble it or attempt

to recharge it outside the system. Do not crush, punctur e , disp ose of in fir e, short the

external contacts, or expose to water or other liquids. Dispose of the battery in

accordance with local regulations and instructions from your service provider.

Battery Safety



Insert batteries correctly. There may be a risk of explosion if the batteries are incorrectly inserted.



Do not attempt to recharge ‘disposable’ or ‘non-reusable’ batteries.



Please follow instructions provided for charging ‘rechargeable’ batteries.



Replace batteries with the same or equivalent type that we recommend.



Do not expose batteries to excessive heat (such as sunlight or fire).



Do not expose batteries to temperatures above 100°C (212°F).

Battery Disposal



The batteries may contain substances that could be harmful to the environment.



Recycle or dispose of batteries in accordance with the battery manufacturer’s instructions and

local/national disposal and recycling regulations.



The batteries may contain perchlorate, a known hazardous substance, so special handling and

disposal of this product might be necessary. For more information about perchlorate and best

management practices for perchlorate-containing substance, see

www.dtsc.ca.gov/hazardouswaste/perchlorate

Provide Ventilation and Select a Location



Remove all packaging material before applying power to the product.



Make certain to operate this unit only in a vertical position.



Do not place this apparatus on a bed, sofa, rug, or similar surface.



Do not place this apparatus on an unstable surface.

IMPORTANT SAFETY INSTRUCTIONS

viii OL-29163-01



Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation

provides proper ventilation.



Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or

other objects on top of this product.



Do not block ventilation openings.

Operating Environment

This product is designed for operation indoors with a temperature range from 32° to 104° F (0° to 40°C).

Each product should have adequate spacing on all sides so that the cooling air vents on the chassis are

not blocked.

Protect from Exposure to Moisture and Foreign Objects

WARNING: Avoid e lectric shock and fire haza r d! Do not expose this product to

dripping or splashing liquids, rain, or moisture. Objects filled with liquids, such as

vases, should not be placed on this apparatus.

WARNING: Avoid e lectr ic shock and fire ha z a rd! Unplug this product before cleaning.

Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning

device (dust remover) to clean this product.

WARNING: Avoid e lectric shock and fire haza r d! Neve r push ob jects thr ough the

openings in this product. Foreign objects can cause electrical shorts that can result in

electric shock or fire.

Service Warnings

WARNING: Avoid electric shock! Do not op e n the cove r of this product. Opening or

removing the cover may expose you to dangerous voltages. If you open the cover, your

warranty will be void. This product contains no user-serviceable parts.

Check Product Safety

Upon completion of any service or repairs to this product, the service technician must perform safety

checks to determine that this product is in proper operating condition.

Protect the Product When Moving It

Always disconnect the power source when moving the apparatus or connecting or disconnecting

cables.

IMPORTANT SAFETY INSTRUCTIONS

OL-29163-01 ix

Telephone Equipment Notice

When using your telephone equipment, basic safety precautions should always be followed to reduce

the risk of fire, electric stock and injury to persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry

tub, in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

Important: Interconnected telecommunication terminal equipment (for example via RJ11) must be UL

listed and the connections must be made in accordance with Article 800 of the NEC

CAUTI ON: To reduce the risk of fire, use only No. 26 AWG or la r ge r

telecommunication line cord.

SAVE THESE I NSTRUCTI ONS

20110316_Cable_Safety

20110316_Modem No Battery_Safety

20110316_Modem with Battery_Safety

20110316_Modem DSL_Safety

United States FCC Compliance

OL-29163-01 xi

United States FCC Compliance

This device has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against such interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy. If not installed and used in accordance with the

instructions, it may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment OFF and ON, the user is encouraged to try to correct the interference

by one or more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.



Consult the service provider or an experienced radio/television technician for help.

Any changes or modifications not expressly approved by Cisco Systems, Inc., could void the

user's authority to operate the equipment.

The information shown in the FCC Declaration of Conformity paragraph below is a

requirement of the FCC and is intended to supply you with information regarding the FCC

approval of this device. The phone numbers listed are for FCC-related questions only and not

intended for questions regarding the connection or operation for this device. Please contact your

service provider for any questions you may have regarding the operation or installation of this device.

Declaration of Conformity

This device complies with Part 15 of FCC

Rules. Operation is subject to the following

two conditions: 1) the device may not cause

harmful interference, and 2) the device must

accept any interference received, including

interference that may cause undesired

operation.

Residential Gateway

Model(s): DPC3939

Manufactured by:

Cisco Systems, Inc.

5030 Sugarloaf Parkway

Lawrenceville, Georgia 30044 USA

Canada EMI Regulation

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.

United States FCC Compliance

x ii OL-29163-01

RF Exposure Statements

Note: This transmitter must not be co-located or operated in conjunction with any other

antenna or transmitter. This equipment should be installed and operated with a minimum

distance of 7.9 inches (20 cm) between the radiator and your body. For products available in

the USA/Canada market, only channels 1-11 can be operated. The selection of other channels

is not possible.

US

This system has been evaluated for RF exposure for humans in reference to ANSI C 95.1

(American National Standards Institute) limits. The evaluation was based in accordance with

FCC OET Bulletin 65C rev 01.01 in compliance with Part 2.1091 and Part 15.27. The minimum

separation distance from the antenna to general bystander is 7.9 inches (20 cm) to maintain

compliance.

Canada

This system has been evaluated for RF exposure for humans in reference to Canada Health

Code 6 (2009) limits. The evaluation was based on evaluation per RSS-102 Rev 4. The

minimum separation distance from the antenna to general bystander is 7.9 inches (20 cm) to

maintain compliance.

20100527 FCC DSL_Domestic

CE Compliance

OL-29163-01 xiii

CE Compliance

Declaration of Conformity with Regard to the EU Directive 1999/5/EC

(R&TTE Directive)

This declaration is only valid for configurations (combinations of software, firmware and

hardware) supported or provided by Cisco Systems for use within the EU. The use of

software or firmware not supported or provided by Cisco Systems may result in the

equipment no longer being compliant with the regulatory requirements.

CE Compliance

x iv OL-29163-01

Note: The full declaration of conformity for this product can be found at

http://www.cisco.com/ we b/co nsumer/ sup port/ comp lia nce_info.html.

The following standards were applied during the assessment of the product against the

requirements of the Directive 1999/5/EC:



Radio: EN 300 328



EMC: EN 301 489-1 and EN 301 489-17



Safety: EN 60950 and EN 50385

The CE mark and class-2 identifier are affixed to the product and its packaging. This product

conforms to the following European directives:

-1999/5/EC

National Restrictions

This product is for indoor use only.

France

For 2.4 GHz, the output power is restricted to 10 mW EIRP when the product is used

outdoors in the band 2454 - 2483.5 MHz. There are no restrictions when used in other parts of

the 2.4 GHz band. Check http://www.arcep.fr/ for more details.

Pour la bande 2,4 GHz, la puissance est limitée à 10 mW en p.i.r.e. pour les équipements

utilisés en extérieur dans la bande 2454 - 2483,5 MHz. Il n'y a pas de restrictions pour des

utilisations dans d'autres parties de la bande 2,4 GHz. Consultez http://www.arcep.fr/ pour

de plus amples détails.

Italy

This product meets the National Radio Interface and the requirements specified in the

National Frequency Allocation Table for Italy. Unless this wireless LAN product is operating

within the boundaries of the owner's property, its use requires a “general authorization.”

Please check http://www.comuni cazi oni.it/i t/ for more details.

Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano

Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all 'interno del

proprio fondo, l'utilizzo di prodotti Wireless LAN richiede una “Autorizzazione Generale”.

Consultare http://www.comuni cazi oni.it/i t/ per maggiori dettagli.

Latvia

The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic

Communications Office. Please check http://www.esd.lv for more details.

2,4 GHz frekvenču joslas izmantošanai ārpus telpām nepieciešama atļauja no Elektronisko

sakaru direkcijas. Vairāk informācijas: http://www.esd.lv.

Note: The regulatory limits for maximum output power are specified in EIRP. The EIRP level

of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the

output power available at the connector (specified in dBm).

20110311_CE_Gateway

La pagina sta caricando ...

Cisco DPC3939 XFINITY Manuale del proprietario

Cisco DPC3939 XFINITY Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti