Jenn-Air JGS9900BDB Manuale del proprietario

Tipo
Manuale del proprietario

Questo manuale è adatto anche per

JENN-AIRGAS
DOWNDRAFT SLIDE-IN RANGE
i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i_i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸i¸i¸¸il¸_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i____i
TABLE OF CONTENTS
Important Safety Instructions .....................................1-4
Ducting Information ...........................................................5
Care & Cleaning ..............................................................5-8
Maintenance .....................................................................8-9
Troubleshooting .........................................................10-11
Surface Cooking .........................................................12-14
Oven Cooking ..............................................................15-20
Options ..........................................................................21-23
Favorites ........................................................................23-24
Setup ..............................................................................24-26
Accessories .........................................................................26
Warranty & Service ...........................................................27
Guide d'utilisation et d'entretien .................................28
Guia de uso y cuidado ....................................................58
JENN-AIE
Form No. A/11/05 Part No. 8113P529 60
@2005 Maytag Appliances Sales Co.
Litho U.S.A.
technician. Do not attempt to adjust, repair, service,
or replace any part of your appliance unless it is
specifically recommended in this guide. All other
servicing should be referred to a qualified servicer.
Always disconnect power to appliance before servicing.
M PORTANT SAFETY
|NSTRU
Warning and important Safety instructions appearing in
this guide are not meant to cover all possible conditions
and situations that may occur. Common sense, caution,
and care must be exercised when installing,
maintaining, or operating the appliance.
Always contact the manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
General Instructions
Read and follow all instructions before using this
appliance to prevent the potential risk of fire, electric
shock, personal injury or damage to the appliance as a
result of improper usage of the appliance. Use appliance
only for its intended purpose as described in this guide.
To ensure proper and safe operation: Appliance
must be properly installed and grounded by a qualified
To check if device is properly installed, look underneath
range with a flashlight to make sure one of the rear
1
levelinglegsisproperlyengagedinthebracketslot.The
anti-tipdevicesecurestherearlevelinglegtothefloor
whenproperlyengaged.Youshouldcheckthisanytime
therangehasbeenmoved.
Child Safety
To Prevent Fire or
Smoke Damage
Be sure all packing materials are removed from the
appliance before operating it.
Keep area around appliance clear and free from
combustible materials. Flammable materials should not
be stored in an oven.
Many plastics are vulnerable to heat. Keep plastics away
from parts of the appliance that may become warm or
hot. Do not leave plastic items on the cooktop as they
may melt or soften if left too close to the vent or a
lighted surface burner.
To prevent grease fires, do not let cooking grease or
other flammable materials accumulate in or near the
appliance.
If appliance is installed near a window, proper
precautions should be taken to prevent curtains from
blowing over burners.
NEVER leave any items on the cooktop. The hot air from
the vent may ignite flammable items and may increase
pressure in closed containers which may cause them to
burst.
Many aerosol-type spray cans are EXPLOSIVE when
exposed to heat and may be highly flammable. Avoid
their use or storage near an appliance.
To eliminate the hazard of reaching over hot surface
burners, cabinet storage should not be provided
directly above a unit. If storage is provided, it should be
limited to items which are used infrequently and which
are safely stored in an area subjected to heat from an
appliance. Temperatures may be unsafe for some items,
such as volatile liquids, cleaners or aerosol sprays.
in Case of Fire
Turn off appliance and ventilating hood to avoid
spreading the flame. Extinguish flame, then turn on
hood to remove smoke and odor.
* Cooktop: Smother fire or flame in a pan with a lid or
cookie sheet.
NEVER pick up or move a flaming pan.
* Oven: Smother fire or flame by closing the oven door.
Do not use water on grease fires. Use baking soda, a
dry chemical or foam-type extinguisher to smother fire
or flame.
NEVER leave children alone or unsupervised near the
appliance when it is in use or is still hot. Children should
never be allowed to sit or stand on any part of the
appliance as they could be injured or burned.
Children must be taught that the appliance and utensils zn
it can be hot. Let hot utensils cool in a safe place, out of
reach of small children. Children should be taught that an
appliance is not a toy. Children should not be allowed to
play with controls or other parts of the appliance.
About Your Appliance
Avoid touching oven vent area while oven is on and for
several minutes after oven is turned off. Some parts of
the vent and surrounding area become hot enough to
cause burns. After oven is turned off, do not touch the
oven vent or surrounding areas until they have had
sufficient time to cool.
Other potentially hot surfaces include cooktop, areas
facing the cooktop, oven vent, surface near the vent
opening, oven door, area around the oven door and oven
window.
Cont.
Do not touch a hot oven light bulb with a damp cloth as
the bulb could break. Should the bulb break, disconnect
power to the appliance before removing bulb to avoid
electrical shock.
To prevent potential hazard to the user and damage to
the appliance, do not use appliance as a space heater to
heat or warm a room. Also, do not use the oven as a
storage area for food or cooking utensils.
NEVER use aluminum foil to cover an oven rack or oven
bottom. Misuse could result in risk of electric shock, fire,
or damage to the appliance. Use foil only as directed in
this guide.
Cooking Safety
Always place a pan on a surface burner before turning it
on. Be sure you know which knob controls which surface
burner. Make sure the correct burner is turned on and
that the burner has ignited. When cooking is completed,
turn burner off before removing pan to prevent exposure
to burner flame.
Always adjust surface burner flame so that it does not
extend beyond the bottom edge of the pan. An excessive
flame is hazardous, wastes energy and may damage the
appliance, pan or cabinets above the appliance.
NEVER leave a surface cooking operation unattended,
especially when using a high heat setting or when deep
fat frying. Boilovers cause smoking and greasy spillovers
may ignite. Clean up greasy spills as soon as possible.
Do not use high heat for extended cooking operations.
NEVER heat an unopened container on the surface
burner or in the oven. Pressure build-up may cause
container to burst resulting in serious personal injury or
damage to the appliance.
Use dry, sturdy potholders. Damp potholders may cause
burns from steam. Dish towels or other substitutes
should never be used as potholders because they can
trail across hot surface burners and ignite or get caught
on appliance parts.
Always let quantities of hot fat used for deep fat frying
cool before attempting to move or handle.
Do not let cooking grease or other flammable materials
accumulate in or near the appliance, hood or vent fan.
Clean hood frequently to prevent grease from
accumulating on hood or filter. When flaming foods
under the hood, turn the fan on.
NEVER wear garments made of flammable material or
loose fitting or long-sleeved apparel while cooking.
Clothing may ignite or catch utensil handles.
Always place oven racks in the desired positions while
oven is cool. Slide oven rack out to add or remove food,
using dry, sturdy potholders. Always avoid reaching into
the oven to add or remove food. If a rack must be
moved while hot, use a dry potholder. Always turn the
oven off at the end of cooking.
Use care when opening the oven door. Let hot air or
steam escape before moving or replacing food.
PREPARED FOOD WARNING: Follow food
manufacturer's instructions. If a plastic frozen food
container and/or its cover distorts, warps, or is otherwise
damaged during cooking, immediately discard the food
and its container. The food could be contaminated.
NEVER use aluminum foil to cover oven racks or oven
bottom. This could result in risk of electric shock, fire, or
damage to the appliance. Use foil only as directed in this
guide.
Utensil Safety
Use pans with flat bottoms and handles that are easily
grasped and stay cool. Avoid using unstable, warped,
easily tipped or loose-handled pans. Also avoid using
pans, especially small pans, with heavy handles as they
could be unstable and easily tip. Pans that are heavy to
move when filled with food may also be hazardous.
Be sure utensil is large enough to properly contain food
and avoid boilovers. Pan size is particularly important in
deep fat frying. Be sure pan will accommodate the
volume of food that is to be added as well as the bubble
action of fat.
To minimize burns, ignition of flammable materials and
spillage due to unintentional contact with the utensil, do
not extend handles over adjacent surface burners.
Always turn pan handles toward the side or back of the
appliance, not out into the room where they are easily hit
or reached by small children.
Never let a pan boil dry as this could damage the utensil
and the appliance.
Follow the manufacturer's directions when using oven
cooking bags.
Only certain types of glass, glass/ceramic, ceramic or
glazed utensils are suitable for cooktop or oven usage
without breaking due to the sudden change in
temperature. Follow manufacturer's instructions when
using glass.
This appliance has been tested for safe performance
using conventional cookware. Do not use any devices
or accessories that are not specifically recommended in
3
this guide. Do not use element covers for the surface
units, stovetop grills, or add-on oven convection
systems. The use of devices or accessories that are not
expressly recommended in this guide can create serious
safety hazards, result in performance problems, and
reduce the life of the components of the appliance.
Deep Fat Fryers
Use extreme caution when moving the grease pan or
disposing of hot grease. Allow grease to cool before
attempting to move pan.
Ventilating Hoods
Clean range hood and filters frequently to prevent
grease or other flammable materials from accumulating
on hood or filter and to avoid grease fires.
When flaming foods under the hood, turn the fan on.
Cleaning Safety
Clean cooktop with caution. Turn off all controls and
wait for appliance parts to cool before touching or
cleaning. Use care to avoid steam burns if a wet sponge
or cloth is used to wipe spills on a hot surface. Some
cleaners can produce noxious fumes if applied to a hot
surface,
Clean only parts listed in this guide.
Self-Clean Oven
Do not clean door gasket. The door gasket is essential
for a good seal. Care should be taken not to rub,
damage, or move the gasket.
Do not use oven cleaners or oven liners of any kind in or
around any part of the self-clean oven.
important Safety Notice
and Warning
The California Safe Drinking Water and Toxic
Enforcement Act of 1986 (Proposition 65) requires the
Governor of California to publish a list of substances
known to the State of California to cause cancer or
reproductive harm, and requires businesses to warn
customers of potential exposures to such substances.
Users of this appliance are hereby warned that when
the oven is engaged in the self-clean cycle, there may
be some low-level exposure to some of the listed
substances, including carbon monoxide. Exposure to
these substances can be minimized by properly venting
the oven to the outdoors by opening the windows and/
or door in the room where the appliance is located
during the self-clean cycle.
IMPORTANT NOTICE REGARDING PET BIRDS:
Never keep pet birds in the kitchen or in rooms where
the fumes from the kitchen could reach. Birds have a
very sensitive respiratory system. Fumes released during
an oven self-cleaning cycle may be harmful or fatal to
birds. Fumes released due to overheated cooking oil, fat,
margarine and overheated non-stick cookware may be
equally harmful.
Save These Instructions for Future Reference
4
Jenn-Air's ventilation system is designed to capture both
cooking fumes and smoke from the cooktop surface. If
the system does not, here are some ducting installation
situations to check:
6" diameter round or 3 114"x 10" rectangular ducting
should be used for duct lengths 10'-60'.
Important: 5" diameter round ducting may be used if
the duct length is 10' or less.
No more than three 90 ° elbows should be used.
Distance between elbows should be at least 18".
,, Recommended Jenn-Air wall cap MUSTbe used.
Make sure damper moves freely when ventilation
system is operating.
There should be a minimum clearance of 6" for
cooktop installed near a side wall.
If there is not an obvious improper installation, there
may be a concealed problem such as a pinched joint,
obstruction in the pipe, etc. Installation is
the responsibility of the installer and
questions should be addressed first by the
installer. The installer should very carefully
check the ducting installation instructions.
Use the Flow Tester Card provided with
your appliance to check the air flow.
FLOW TESTER
t
._;_;;;_,_;;_;÷;;...
CARE CLEANING
Self-Clean Oven
2. Remove broiler pan, all pans, and oven racks from the
oven. The oven racks will discolor and may not slide easily
after a self-clean cycle if they are not removed.
Important: Removethe air grille from the cooking surface
before self-cleaning.
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior.
The oven should be cleaned regularly by wiping up spillovers 5.
to prevent excessive smoke and flare-ups. Do not allow a
heavy build-up of soil to accumulate in the oven.
During the cleaning process, the kitchen should be well 6.
ventilated to get rid of normal odors associated with cleaning.
Before Self-Cleaning
1. Turn off the oven light before cleaning. The oven light may
burn out during the clean cycle.
To set Serf=Clean:
1. Press Clean pad.
Clean oven frame, door frame, area outside of gasket, and
around the opening in the door gasket with a nonabrasive
cleaner such as Ban Ami* or detergent and water. The
self-cleaning process does not clean these areas. They
should be cleaned to prevent soil
from baking on during the clean
cycle. (The gasket is the seal
around the oven door and window.)
To prevent damage, do not clean
or rub the gasket around the oven
door. The gasket is designed to
seal in heat during the clean cycle.
Wipe up excess grease or spill-overs from the oven
bottom. This prevents excessive smoking, flare-ups or
flaming during the clean cycle.
Wipe up sugary and acidic spillovers such as sweet
potatoes, tomato, or milk-based sauces. Porcelain enamel
is acid-resistant, not acid-proof. The porcelain finish may
discolor if acidic or sugary spills are not wiped up before a
self-clean cycle.
/, .......
( Clean
" .......... /
2. REMOVE RACKSwill bedisplayed. Remove the racks.
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
5
3. SelectCONTINUE using the Quickset pad. The Quickset
pads are located on either side of the control panel dsplay.
4. Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Press the Enter pad.
OR
Select MEDIUM for a moderately soiled oven and three
hours of cleaning time.
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
5. CLEAN, TIME, LOCKED and the cleaning time countdown
will be displayed while the oven is cleaning. OVEN
COOLING will appear in the display when the cleaning
time has been completed and the oven is still locked.
Important: The door lock will disengage approximately one
hour after the cleaning time is completed. OVEN COOLING
will go off in the display when the oven door has unlocked.
To Delay a Self=Clean Cycle:
1. Press Clean pad.
2. REMOVE RACKSwill be displayed.
Remove the racks.
// ................... ,\
( Clean
\ .................. /
3,
4.
Select CONTINUE using the Quickset pad..
Set LIGHT soil level by entering 200 using the number
pads for two hours of cleaning time. Press the Enter pad.
OR
Select MEDIUM for a moderately soiled oven and three
hours of cleaning time,
OR
Select HEAVY for a heavily soiled oven and four hours of
cleaning time.
The door will lock. CLEAN,TIME, LOCKED and the
cleaning time countdown will be displayed
6. After door locks, press the Mere Options pad.
7. Select DELAY using the Quickset pad.
8. Select the number of hours you want to delay the start of the
self-clean cycle.
9. The delay time and cleaning time will be displayed.
After Self=Cleaning
About one hour after the end of the clean cycle, the lock
will disengage a/td OVEN COOLING will go off in the
display. At this point, the doer can be opened.
Some soil may leave a light gray, powdery ash which can be
removed with a damp cloth. If soil remains, it indicatesthat
the clean cycle was not long enough. The soil will be removed
during the next clean cycle.
If the oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and embossed rack
supports with a small amount of vegetable oil to restore ease
of movement.
A white discoloration may appear after cleaning if acidic or
sugary foods were not wiped up before the clean cycle. This is
normal and will NOT affect performance.
Notes:
If the oven door is left open, CLOSEDOORwill appear in
the display until the door is closed.
If more than 30 seconds elapse between pressing the
Clean pad and pressing a number pad, the program will
automatically return to the previous display.
The oven door will be damaged if it is forced to open
during cleaning or cooling process.
The first few times the oven is cleaned, some smoke and
odor may be detected. This is normal and will lessen or
disappear with use. If the oven is heavily soiled, or if the
broiler pan was accidently left in the oven, excessive
smoke and odor may occur.
As the oven heats and cools, you may hear sounds of
metal parts expanding and contracting. This is normal
and will not damage your appliance.
6 Cont.
Cleaning Procedures
Brand names are registered trademarks of the
respective manufacturers.
** To order call 1-800-JENNAIR (1-800-536-6247].
Broiler Pan
and Insert
Burner Caps
and Sealed
Gas Burners
Burner Grates
Porcelain on
Cast Iron
Cooktop -
Porcelain
Enamel
Clock and
Control Pad
Area
Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.
Place soapy cloth over insertand pan; let soak to loosen soil.
° Wash in warm, soapy water. Use scouring pad to remove stubborn soil.
° Broiler pan and insertcan be cleaned in dishwasher.
Removable Burner Caps
° Allow burner to cool. Remove burner cap and wash in soapy water with a plastic scouring pad. For
stubborn soils, clean with a soap-filled, nonabrasive pad or Cooktop Cleaning Creme_
(Part #20000001] _*and a sponge.
° Do not clean in the dishwasher or self-cleaning oven.
Sealed Gas Burners
Clean frequently. Allow burner to cool. Clean with soap and plastic scouring pad. Forstubborn or
dried-on soils, clean with a soap-filled, nonabrasive pad, stiff brush, toothbrush, the soft rubber tip on
the toothbrush (if equipped] or a straight pin. Do not enlarge or distort holes.
° Be careful not to get water into burner ports.
Use care when cleaning the ignitor. If the ignitor iswet or damaged the surface burner will not light.
Wash with warm, soapy water and a nonabrasive, plastic, scrubbing pad. For stubborn soils,
clean with a soap-filled, nonabrasive, plastic pad or Cooktop Cleaning Creme_and a sponge. If soil
remains, reapply Cooktop Cleaning Creme_,cover with a damp paper towel and soak for 30 minutes.
Scrub again, rinse and dry.
Do not clean in the dishwasher or self-cleaning oven.
Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid-resistant, not acid-
proof. All spillovers, especially acidic or sugary spillovers, should be wiped up immediately with a dry cloth.
When cool, wash with soapywater, rinse and dry.
Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.
° Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.
o
o
o
To activate control lock for cleaning, see Locking the Control, page 16.
Wipe with damp cloth. Dry thoroughly.
Glasscleaners may be used if sprayedon a cloth first. DO NOTspray directly on contrelpads and
display area.
Do not use other cleaning sprays,abrasive cleaners or large amounts of water on the panel.
o
Control Knobs Removeknobs in the OFFposition by pulling forward.
Wash, rinse and dry. Do not use abrasivecleaning agents as they may scratch the finish.
° Turn on each element to be sure the knobs have been correctly replaced.
Oven Window ° Avoid using excessiveamounts of water which may seep under or behind glass, causing staining.
and Door = ° Wash with soap and water. Rinsewith clear water and dry. Glasscleaner can be used if sprayed on a cloth.
Glass Do not useabrasive materials such as scouring pads, steel wool or powdered cleaners as they will scratch.
Oven Interior Follow instructions on pages 5-6 to set a self-clean cycle.
Oven Racks
o
o
o
Clean with warm, soapy water.
Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.
Racks will permanently discolor and may not slide smoothly if left in the oven during a self-clean
operation. If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to
restore ease of movement, then wipe off excess oil.
_i:ij:ijii!i_ii_i_Ti iiii!,!i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii!iii_ii_!iiiiiliiiii_ii_iIiiiiiiiiiiiii!iiiii!i!i!i!ili!_=__ii,li_i,_ii_ii_!i_i!_i!ii_iE! i!i!i!i!i!iIi!iii!_ii_!iiiiiiiiiilililiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!iiiii!iiiii!iiiiiiiiil,ilililililililililililililililililililililililililililililililili_i!_ii_ii_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_ii_iiii_ii_ii_ii_iiiiiiiiiiiiii_ii,ii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!iiiii!!i,ilililililililililiIil,il,ililii!_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_ii_!i_ii_!i_!i!!_iiiii!_ii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!iiiii!iiiii!i!iiiii!ii,liiiiiiiii!ii!!ii_ii_iii_i_ii!i_!i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_!_i_!i_i!!!ii_i_!ii_i_!ii_i_iiii_ii_i!_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ili_i!_i!iiiiiiiiiiiii!i!,!i!i!iii!iii!iii!i!i!!_!!i!i!!!!!!!!!!!!!!!ii!_ii!iiii!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_ii_i!_!i!iiiii!_!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_ii_ii_i!_!i_i!_!iii!_!iiiii_!i_iiiiiiii!!i!!ii!ii!i!!!iiiii!iii_i!,!i_i!i!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!i!!i!ii!!!i!i!i!i!i!i!!!_!i_iIi!ii!!i!ii!!!!ii!!!!i,!Iii!ii!!_!!_!i_!!_!i_!!_!i_!ii_!!i!_iliiii_ii_!iiii!ii!ii!!i!!i!!i!!i!!i!!i!!i!iii!!i!i!ii_il'I
Side Panels, When cool, wash with warm, soapy water, rinse and dry. Never wipe a warm or hot surface with a damp
and Door cloth as this may damage the surface and may cause a steam burn.
Handles - Forstubborn soil, use mildly abrasive cleaning agents such as baking soda paste or Ben Ami*. Do not use
Painted Enamel abrasive cleaners such as steel wool pads or oven cleaners. These products will scratch or permanently
damage the surface.
Note: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may
discolor or dull if soil is not immediately removed. This is especially important for white surfaces.
Stainless Steel ° DO NOT USEANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.
(select models:) ° DO NOT USEABRASIVE OR ORANGE CLEANERS.
ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.
Daily Cleaning/Light Soil -- Wipe with one of tile following - soapy water, white vinegar/water solution,
Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse
and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.
20000008)**.
° IVloderate/Heavy Soil -- Wipe with one of the following - Ben Ami, Smart Cleanser, or Soft Scrub* -
using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi-
purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks,
follow with Stainless Steel Magic Spray_.
Discoloration -- Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse
immediately and dry. To remove streaks and restore luster, follow with StainlessSteel Magic Spray*.
Brand names for cleaning products are registered trademarks of the respective manufacturers.
•* To order direct, call 1-800-JENNAIR (1-800-536-6247:).
A|NTENANCE
Oven Door
2. Align slots in the door with the hinge arms on the range.
3. Slide the door down onto the hinge arms until the door is
completely seated on the hinges. Push down on the top
corners of the door to completely seat door on hinges.
Door should not appear crooked.
Important: The oven door on a new range may feel "spongy"
when it isclosed. This is normal and will decrease with use.
NEVER attempt to open or close door or operate oven until
door is properly replaced.
NEVER place fingers between hinge and front oven frame.
Hinge arms are spring mounted. If accidentally hit, the
hinge will slam shut against oven frame and could injure
your fingers.
To remove:
1. When cool, open the oven door
to the broil stop position
(opened about four inches:).
2. Grasp door at each side. Do not
use the door handle to lift door.
3. Lift up evenly until door clears
hinge arms.
To replace:
1. Grasp door at each side.
Oven Window
To protect the oven door window:
1. Do not use abrasive cleaning agents such as steel wool
scouring pads or powdered cleansers as they may scratch
the glass.
2. Do not hit the glass with pots, pans, furniture, toys, or
other objects.
3. Do not close the oven door until the oven racks are in
place.
Scratching, hitting, jarring or stressing the glass may weaken
its structure causing an increased risk of breakage at a later
date.
Cent.
Oven Light
To assure the proper replacement bulb is used, order bulb
from Jenn-Air. Call 1-800-JENNAIR (1-800-536-6247), ask for
part number 74004458 - halogen bulb.
To Replace Oven Light Bulb:
1. Disconnect power to the oven.
2. When oven iscool, use fingertips to grasp edge of bulb
cover. Pull out and remove.
3. Carefully remove old bulb by pulling straight out of
ceramic base.
4. To avoid damaging or decreasing the life of the new bulb,
do not touch the bulb with bare hands or fingers. Hold
with a dry cloth or paper towel. Push new bulb prongs
straight into small holes of ceramic base.
5. Replace bulb cover by snapping into place.
6. Reconnect power to the oven. Reset clock.
Leveling Legs
Be sure the range is leveled when installed. If
Removal of Gas Appliance
Gasappliance connectors used to connect this appliance to
the gas supply are not designed for continuous movement.
Once installed, DO NOT repeatedly move this gas appliance
for cleaning or to relocate. If this appliance has to be moved
and/or removed for servicing, follow the procedure described
in the installation instructions. For information, contact Jenn-
Air Customer Service at 1-800-JENNAIR (1-800-536-6247).
To prevent range from accidentally tipping, range must be
secured to the floor by sliding rear leveling leg into the anti-
tip bracket.
Electrical Connection
Appliances which require electrical
power are equipped with a three=prong
grounding plug which must be plugged
directly into a properly grounded three-
hole 120 volt electrical outlet.
Always disconnect power to appliance before servicing,
The three-prong grounding plug offers protection against
shock hazards. DO NOT CUT OR REMOVE THE THIRD
GROUNDING PRONG FROM THE POWER CORD PLUG.
If an ungrounded, two-hole or other type electrical outlet is
encountered, it is the personal responsibility of the
appliance owner to have the outlet replaced with a
properly grounded three=hole electrical outlet.
the
range is not level, turn the leveling legs, [4
located at each corner of the range, until range J I
islevel, oh I
ANTI RACKET
\ LEVELING LEG
9
T UBLE NG
For most concerns, Check if oven controls have been properly set.
try these first. Check to be sure plug is securely inserted intoreceptacle.
Check or re-set circuit breaker. Check or replace fuse.
Check power supply.
Part or all of appliance does
not work.
Clock, indicator words, and/or
lights operate but oven does
not heat.
Check if surface and/or oven controls have been properly set. See pgs. 12 & 17.
Check ifoven door is unlocked after self-clean cycle. See pg. 6.
Check ifoven isset for a delayed cook or clean program. See pgs. 17 & 6.
Check ifControl Lock is activated. See pg. 16.
Check ifcontrol is in Sabbath Mode. See pg. 25.
Oven may be set for a Cook & Hold or delay function.
Control Lock may have been set. See pg. 16.
Surface burner fails to light. Check to be sure unit isproperly connected to power supply.
Check for a blown circuit fuse or a tripped main circuit breaker.
Check to be sure ignitor is dry and clicking. Burner will not light if ignitor is damaged,
soiled or wet. If ignitor doesn't click, turn control knob OFF.
Burner ports may be clogged.
Check to be sure a pan is sitting on the grate above.
The flame is uneven.
Surface burner flame lifts
off ports.
Food is not broiling properly
or smokes excessively.
Baking results are not as
expected or differ from
previous oven.
o
°
°
°
°
Oven will not self=clean.
o
°
°
Check oven rack positions. Food may be too close to flame.
Aluminum foil was incorrectly used. Never line the broiler insert with foil.
Trim excess fat from meat before broiling.
A soiled broiler pan was used.
Preheat oven for 2-3 minutes before placing food in the oven.
° Broil with the oven door closed.
Check the oven temperature selected. Make sure oven is preheated when recipe
or directions recommend preheat.
Make sure the oven vent has not been blocked. See page 20 for location.
Check to make sure range is level.
Temperatures often vary between a new oven and an old one. As ovens age, the oven
temperature often "drifts" and may become hotter or cooler. See page 25 for
instructions on adjusting the oven temperature. Important: It isnot recommended
to adjust the temperature if only one or two recipes are in question.
Usecorrect pan. Dark pans produce dark browning. Shiny pans produce light browning.
Check rack positions and pan placement. Stagger pans when using two racks. Allow
1-2 inches between pans and oven wall.
Check the use of foil in the oven. Never use foil to cover an entire oven rack. Place
a small piece of foil on the rack below the pan to catch spillovers.
Check to make sure the cycle is not set for a delayed start. See pg. 6.
Check if door is closed.
Check if control is in Sabbath Mode. See pg. 25.
Oven may be over 400° F.Oven temperature must be below 400° Fto program a
clean cycle.
10 Cont.
Ovendid not clean properly.
Oven door will not unlock after
self=clean cycle.
There are no beeps and
no display.
Moisture collects on oven
window or steam comes from
oven vent=
There is a strong odor or light
smoke when oven isturned on.
o
o
Ventilation system is not
capturing smoke efficiently.
o
o
Fault Codes
®
o
Noises may be heard. °
°
SAb flashing and then
displayed continuously.
Cannot add another Favorite.
° Longercleaning time may be needed.
Excessivespillovers, especially sugary and/or acidic foods, were not removed prior
to the self-clean cycle.
° Oven interioris still hot. Allow about one hour for the oven to cool after the
completion of a self-clean cycle, The door can be opened when the LOCK indicator
word is not displayed,
° The control and door may be locked, See pg. 6.
Oven may be in Sabbath Mode. See page 25.
This is normal when cooking foods high in moisture.
Excessivemoisture was used when cleaning the window.
This is normal for a new range and will disappear after a few uses. Initiating a clean
cycle will "burn off" the odors more quickly.
Turning on a ventilation fan will help remove the smoke and/or odor.
Excessivefood soils on the oven bottom. Use a self-clean cycle.
Check on cross ventilation in room or make up air.
Outside wall cap may be trapped shut.
Rangemay be improperly installed; check ducting information. See pg. 5.
Air filter may be improperly installed. See pg. 14.
The oven may detect a fault during programming or during operation. If a fault is
detected, the message FAULTDETECTED- PRESSPOWERTO CLEARor FAULT
DETECTED- PRESSENTERTO TRYAGAIN may appear. Follow directions in the display.
If the fault reappears or does not clear, call an authorized servicer or the toll-free number
in the display.
If the same operation is attempted before having the oven repaired, the message
FEATURENOT AVAILABLE will appear. The feature will remain inoperable until service
isobtained.
If the oven is heavily soiled, excessive fiareups may result in a fault code during cleaning.
Pressthe CANCEL padand allow the oven to cool completely, wipe out excess soil, then
reset the clean cycle. If the fault code reappears, contact an authorized servicer.
The oven makes several low-level noises.You may hear the oven relays as they go on
and off. This is normal.
As the oven heats and cools, you may hear sounds of metal parts expanding and
contracting. This is normal and will not damage your appliance.
Oven isinSabbath Mode. To cancel, press and hold the Setup pad for five seconds.
° Favorites is full. To delete a favorite and add another, see page 23.
11
SURFACE COOKING
Low: Use to simmer foods, keep foods
warm and melt chocolate or butter. Some
cooking may take place on the Low
setting if the pan iscovered. It is possible
to reduce the heat by rotating the knob
toward OFF. Be sure flame isstable.
High: Use to bring liquid to a boil, or reach
pressure in a pressure cooker. Always
reduce setting to a lower heat when liquids
begin to boil or foods begin to cook.
An intermediate flame size is used to
continue cooking. Food will not cook any
faster when a higher flame setting is used
than needed to maintain a gentle boil.
Water boils at the same temperature
whether boiling gently or vigorously.
Surface Controls
Setting the controls:
The size and type of cookware will affect the heat setting.
1. Place a pan on the burner grate.
* The burner flame may lift off or appear separated from
the port if a pan is not placed on the grate.
2. Push in and turn the knob to the desired setting.
A clicking (spark] sound will be heard and the burner
will light.
Important: Eachsurface burner isequipped to provide
automatic reignition ifthe flame should somehow get
blown out.
Pilotless ignition
Pilotless ignitioneliminates the
need for a constant standing
pilot light. Eachsurface burner
has a spark ignitor.Use care
when cleaning around the
surface burner.
If the surface burner does
not light, check if ignitor is
broken, soiled or wet.
BURNER CAP
BURNER BASE
Surface Control Knobs
Use to turn on the surface burners. An infinitechoice of heat
settings is available from Low to High. At the High setting a
detent or notch may be felt. The knobs can be set on or
between any of the settings.
Graphics next to the knob identify which burner
It the knob controls. For example, the graphic at left
OFront shows the right front burner location.
12
Operating During a
Power Failure
1. Hold a lighted match to the desired surface burner head.
2. Push in and turn the control knob slowly on.
3. Adjust the flame to the desired level.
Cooktop
To prevent the cooktop from discoloring
or staining:
Clean cooktop after each use.
Wipe acidic or sugary spills as soon as the cooktop has
cooled as these spills may discolor the
porcelain.
Unlike a range with standard gas burners,
this cooktop does not lift up nor isit
removable. Do not attempt to lift the
cooktop for any reason.
Burner Grates
The grates must be properly positioned before cooking.
When installing the grates, place the tab ends toward the
center, matching the straight bars.
Improper installation of the grates may result in chipping of
the cooktop.
Sealed Burners
The sealed burners of your range are secured to the cooktop
and are not designed to be removed. Since the burners are
sealed into the cooktop, boilovers or spills will not seep
underneath the cooktop.
However, the burner should be cleaned after each use. The
cap portion of the burner is easily removed for cleaning. (See
page 7 for cleaning directions.]
The burner caps must be correctly placed on the burner base
for proper operation of the burner.
High Performance Burner
There isone 16,000BTU* high speed burner on your range,
located in the right front position. This burner offers higher
speed cooking that can be used to quickly bring water to a
boil and for large-quantity cooking.
Low Turn Down Burner
This burner is located in the right rear
position. The Simmer setting can be
used to steam or poach foods, to cook
delicate sauces or continue cooking
covered foods. The ultra-low Melt
setting is best for melting
chocolate and butter.
important: When using the normal settings
for preparing foods, it may take a few minutes for the cooking
area to cool to the Melt heat setting.
BTU ratings will vary when using LP gas.
Dual Ring Burner (selectmodels)
The cooking surface isequipped with a dual
ring burner located in the left front _
position. To operate, push in on the
control knob and turn counterclockwise
to light the burner. Continue turning
until the desired setting is reached. The
lighting sequence is:inner burner on
High, then inner burner on Low,then bot
rings on High, then both rings on Low.
Do not operate the burners without a pan on the grate.
The grate's porcelain finish may chip without a pan to
absorb the heat from the burner flame.
Use care when stirring food in a pot/pan sitting on the burner
grate. The grates have a smooth finish for ease of cleaning.
The pot/pan will slide if the handle is not held. This may result
in spilling of hot food items and may be a burn hazard.
Although the burner grates are durable, they will gradually
lose their shine and/or discolor, due to the high temperatures
of the gas flame.
Notes:
A properly adjusted burner with clean ports will light
within a few seconds. If using natural gas, the flame
will be blue with a deeper blue inner cone.
If the burner flame isyellow or is noisy, the air/gas
mixture may be incorrect.Contact a service technician
to adjust. (Adjustments are not covered by the
warranty.)
With LPgas, slight yellow tips on the flames are
acceptable. This isnormal and adjustment isnot
necessary.
With some types of gas, you may hear a "popping"
sound when the surface burner is turned off. This is a
normal operating sound of the burner.
Ifthe control knob is turned very quickly from High to
Low, the flame may go out, particularly ifthe burner is
cold. If this occurs, turn the knob to the OFF position,
wait several seconds and relight the burner.
The flame should be adjusted so it does not extend
beyond the edge of the pan.
13
Ventilation System
The built-in ventilation system removes cooking vapors, odors
and smoke from foods prepared on your cooktop and grill.
To operate the ventilation
system manually, push the .... F_,_,,,_
T_M_T
o,,or
Vent Fan pad located on the ..... _,_,_,,
electronic control. Push once ............
for Low, push again for High _,_,I_:,I,o'_0'_,_
V_nt
and a thirdtime to turn the _"
fan Off.
The ventilation system will operate automatically when the
grill element is in use.
The fan can be used to remove strong odors from the
kitchen as when chopping onions near the fan.
Care and Cleaning of the
Ventilation System
° Air Grille: Tile air grille lifts off easily.Wipe clean or wash in
dishwasher or sink with mild household detergents. To
prevent scratching the surface, do not use abrasive
cleaners or scrubbing pads.
FILTER
° Filter: Turn off ventilation system before removing. The filter
is a permanent type and should be cleaned when soiled.
Clean in sink with warm water and detergent or in
dishwasher.
iMPORTANT: DO NOT OPERATESYSTEMWITHOUT
FILTER.Filter should always be placed at an angle. As you
face the front of the range, the top of the filter should rest
against the left side of the vent opening. The bottom should
rest against the right side of the vent chamber at the
bottom. Important: If filter is flat against the fan wall,
ventilation effectiveness is reduced.
° Ventilation Chamber: This area,which houses the filter,
should be cleaned in the event of spills or whenever it
becomes coated with a film of grease. It can be cleaned with
paper towel, damp cloth, or sponge and mild household
detergent or cleanser.
Important: The oven vent islocated under the right side of
the air grille. When using or cleaning the oven, hot and
moist air may be noticed in this area. The area near the vent
may become hot enough to cause burns. Be careful not to
spill anything intothis vent. The air grille must be
removed before the self=clean cycle.
14
OVENCOOK=NG
Control Panel
AB CD
.............C_ "PavorJteSon/o_On'_el_LIp/ Off
Clean
Rapid More
-- Preheat iis_
J KL
TIMER1
On/Off
Vent OVeR
Fan Light CANCEL
°ni° I t
N N 0
G
TIMER2
On/Off
P
H
! ,
2 3
ABC DEF
4 5 6
GHI JI(L MNO
7 8 9
PQRS TtJV WXYZ
Back 0 Enter
1 Space I
lock
The control panel is designed for ease in programming. The display window shows options for each function and moves from step
to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake
operation.
Rapid Preheat
Convect
Bake
Broil
TIMER 1
Display
TIMER 2
Number Pads
Favorites
More Options
Clean
Setup
Vent Fan
Oven Light
CANCEL
Quickset pads
Use to decrease preheating time.
Use for convection baking and roasting.
Use for baking and roasting.
Use for broiling and top browning.
Sets timer.
Displays oven functions, options and
window time of day.
Sets timer.
Use to enter time and temperature,
or to enter Favorites names.
Use to access, program or save
baking cycles.
Use to access additional features.
Use to set self-clean cycle.
Use to view or change factory
default settings.
Activates the ventilation fan on
the cooktop.
Use to turn the oven light on or off.
Cancels all operations except Timer,
Clock, Favorites, Setup and Vent Fan.
Use to select options in display
window (next to display window
on both sides].
Quickset Pads
Quickset pads are located on each side of tile display window
and are used to select the desired function or option in the
display window. To select the option or function, press the
Quickset pad next to the word.
If you need to back out of a function or option in the display,
press the Back pad. When your programming is complete,
press the Enter pad or wait four seconds and the function will
start automatically.
Up arrows indicate additional screens with additional options.
Pressthe Quickset pads next to the arrows to scroll through
the display.
Important: Fourseconds after entering the function,
option, number or letter, the function will automatically be
entered. If more than 30 seconds elapse between steps in
programming, the function will be canceled and the
display will return to the previous display.
Clock
Setting the Clock: jj.............
1. Press the Setup pad. Setup !
k On/Off /
2. Select CLOCK using the Quickset pads. ...........
3. Select TIME.
4. Enter the time using the number pads.
5. Press Enter pad.
6. Select AM or PM in 12 hour mode. (For 24 hour clock, see
page 16.]
7. To exit the Setup mode, press Setup pad.
15
Activating and canceling the clock/day
of week display: ...................
1. Press Setup pad. /setup
On/Off/
2. Select CLOCK. J
3. Press the arrow to scroll until DISABLE is displayed.
4. Select DISABLE.
5. Select TIME.
6. Select OFF to turn the clock display off, or select ON to turn
the clock display on.
7. Select OFF to turn the day of the week display off Select
ON to turn the weekday display on.
8. To exit the Setup mode, press Setup pad.
Entering the day of the week:
1. Press Setup pad.
2. Select CLOCK.
/, ...............
; Setup
, On / Off/
3. Press the arrow to scroll until DAY is displayed.
4. Use Quickset arrow to scroll through the days.
5. Select day desired.
6. To exit the Setup mode, press Setup pad.
To set the clock for a 12 or 24 hour format:
The clock can be set to display time in either a 12 hour or 24
hour format. /.........................
/ Setup
1. Press the Setup pad.
On/Off/
2. Select CLOCK. " ..........
3. Use the arrow to scroll to the next screen.
4. Select 12/24 HOUR.
5. Select 12 HB or 24 HR.
6. To exit Setup mode, press Setup pad.
Timers
Setting the Timers (Timer 1 or Timer 2):
1. Press TIMER 1 or TIMER 2 pad. _TIMER 1
2. Press one of the displayed times using the , On / Off /
Quickset pads, or press the number pads to ...........
enter the desired time.
Important: Eachpress of the displayed time choices adds
additional time. Forexample, pressing "10 MIN" three
times provides 30 minutes on the timer (0:30).
3. Press Enter pad.
Changing the amount of time entered once the
Timer starts:
1. PresstileTIMER 1 or TIMER 2 pad once. "TIMER1
On / Off /
2. Press the displayed times on the Quickset ..................................
pads repeatedly until the desired time is entered.
OR
3. Press the number pads to enter the new desired time.
4. Press Enter pad.
Canceling the Timer:
1. Press the TIMER 1 or TIMER 2 pad twice.
If both Timers are active:
/ TIMER1 .....
On/Off
If the desired Timer is already in the foreground, press once
for edit mode and twice to cancel the Timer. If the desired
Timer is not in the foreground, follow the steps below.
1. Press the desired TIMER pad once. The selected Timer will
come to the foreground.
2. Press the TIMER pad a secondtime to access the edit
mode in order to make changes.
3. Pressing the TIMER pad a thirdtime will cancel the Timer.
Changing the Timer beeps:
The signal beeps for TIMER 1 and TIMER 2 can be changed.
The options available are two beeps every thirty seconds, two
beeps every sixty seconds or one beep only. The default
setting is one beep.
1. Press the Setup pad. / Setup
2. SelectthearrowtoscrolluntilTONES On /Off/
/
isdisplayed. ........
3. Select TONES,
4. Select TIMERS TONES.
5. Select the desired timer beep format [2-30 SEC,2-60 SEC
or 1 BEEP).
6. Press Setup pad to exit Setup mode.
Locking the Control and Oven Door
The oven control and oven door can be locked to prevent
accidental programming. If an oven function is currently
being used, the control and door cannot be locked.
To lock the control and door:
Press the Back and Enter pads at the same time, holding for
three seconds or until CONTROL LOCKED appears in the
display.
To unlock the control and door:
Press the Back and Enter pads at the same time, holding for
three seconds. UNLOCKING DOORwill appear in the display
when the control and door are unlocking.
Back 0 Enter
16
Baking
/ ................
To set Bake: J
Bake
1. Press the Bake pad.
2. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
The temperature can be set from 170° Fto 550° F
in increments.
After three seconds, the oven will begin to preheat.
BAKE and PREHEATwill appear in the display along
with 100°or the actual oven temperature, whichever
ishigher.
The temperature in the display will increasein
incrementsuntil the oven reaches the preset
temperature. Allow about 15 minutes for the oven
to preheat.
° When the oven ispreheated, the oven will beep and
PREHEATwill no longer be displayed.
3. At the end of cooking, turn the oven off by J_............ ,,
pressing the CANCEL pad. Remove food CANCEL
from the oven. The oven will continue ..............
operating until the CANCEL pad ispressed.
Notes:
° If more than thirty seconds elapse between pressing a
pad and pressing a number pad, the display will return
to the previous display.
Whenever the temperature appears in the display, the
oven isheating.
° To change the oven temperature during cooking, press
the Bake pad and select a displayed temperature or use
the number pads to enter the desired temperature.
The oven will automatically shut off after 12 hours if it is
accidentally left on. To set a Sabbath Mode, see Sabbath
Mode, page 25.
Bake Options
Cook & Hold and Delay options are available when baking.
When using the Cook & Hold option, the oven begins to heat
immediatelyafter the control has been set. Then, the oven
cooks for a specified length of time. When that time has
elapsed, the oven will automatically reduce temperature to
170° Fand keep the food warm for up to an hour and then
automatically turn off.
When using Delay, the oven begins to cook later in the day.
Set the amount of time that you want to delay before the oven
turns on and how long you want to cook. The oven begins to
heat at the selected time and cooks for the specified length of
time. When that time has elapsed, the oven will keep the food
warm for up to an hour then automatically turn off.
To set Cook & Hold:
1. After Bake has been programmed, press
the More Options pad.
2. Select COOK/NLD.
/ ............
/ More
,,Options
/
3. Select the amount of time you want to bake by pressing
the Quickset pads or the number pads.
4. Press ENTER.
5. COOK TIME, the cook time countdown, PREHEAT,BAKE
and the actual temperature will be displayed.
The oven will cook for the selected time, then keep food warm
for one hour.
To set a Delay:
/"
1. After Bake has been programmed, press More "
the More Options pad. Options
/
2. Select DELAY.
3. Select the amount of time you want to delay the start of
cooking using the displayed times or the number pads.
4. Select the amount of time you want to cook using the
displayed times or the number pads.
5. The display will show BAKE,the temperature, the delay
time and the cook time countdown.
6. When the delay time has expired, the oven will begin
heating. COOKTIME, the cook time countdown, PREHEAT,
BAKE and the actual oven temperature will be displayed.
Conveot
Convection uses a fan to circulate hot air evenly over, under and
around the food. As a result, foods are evenly cooked and
browned, often in shorter times, at lower temperatures and with
the flexibility of using more than one rack at a time.
Convect Options
Cook & Hold and Delay
options are available when
convect cooking. See
page 21 for information on
how to program a Cook &
Hold or Delay option.
17
Multiple-Rack
Baking of
Cookies/Biscuits
Breads
Casseroles
Whole Chicken
Whole Turkey
Vegetables
Pork Roasts
Beef Roasts
Tarts/Tortes
Cakes
Notes:
, The oven control comes from the factory set for Auto
Convect Conversion. When using Convect Bake enter the
conventional baking temperature. The control
automatically converts the temperature to 25° less than
the conventional temperature.
When using Convect Roastthe temperature will not be
automatically reduced. Enterthe conventional roasting
temperature and time. The control then lets you know
when 750/0of the time has elapsed and alerts you to check
the food for doneness.
To turn Auto Convect Conversion off, see page 24.
Convect Bake
To set Convect Bake:
1. Pressthe Convect pad. Coiqvect
2. Select CNVT BAKE using the Quickset pads.
3. Select the oven temperature using the Quickset pads
OR
Enter the desired temperature using the number pads.
Press Enter pad to set.
The temperature can be set from 195° Fto 550° F
degrees in 5° increments.
After three seconds, the oven will begin to preheat. CNVT
BAKEand PREHEATwill appear in the display along with
100° or the actual oven temperature, whichever is higher.
° The temperature in the display will increase in
increments until the oven reaches the preset temperature.
Allow about 15 minutes for the oven to preheat.
When the oven is preheated, the oven will beep, and
PREHEATwill turn off and CNVT BAKE will be displayed.
AUTO will be displayed if Auto Convect Conversion
feature is turned on.
Placefood in the oven.
4. At the end of cooking, turn the oven off by pressing the
CANCEL pad. Remove food from the oven. The oven will
continue operating until the CANCEL pad is pressed.
Convect Roast
To set Convect Roast:
1. Placefood in the oven.
2. Pressthe Convect pad.
3. Select CNVT ROAST using the Quickset pads.
4. Select the oven temperature using the Quickset pads.
OR
Enter the desired temperature using the number pads.
PressEnter pad to set.
The temperature can be set from 195° Fto 550° F
degrees in 5° increments. If Auto Convect Conversion is
turned off, you can set 170° F.
5. Enter desired cook time. Enter the conventional roasting
time using the number pads.
After three seconds, the oven will begin to heat. CNVT
ROASTwill appear in the display along with 100° or the
actual oven temperature, whichever is higher.
The temperature in the display will increase in
increments until the oven reaches the preset
ternperature.
° Cook time will begin to count down.
6. At 750/0of the cooking time the oven will beep to let you
know to check food. Check food using a meat thermom-
eter. If food is done, take food out of oven and press
CANCEL pad to turn oven off.
7. If food is not done, continue roasting.
Once the set time has elapsed the oven will automatically
go intoKeep Warm mode for 1 hour. If /............................,
food is taken from the oven before the hour { CANCEL i
has elapsed, press CANCEL pad. "....................................
NOteS:
If the recipe suggests preheating the oven, add time to
cook time.
If Auto isoff, roast time will not be required.
Rapid Preheat
Use to decrease preheating time when usHlg Bake or Convect
Bake. Use for all foods when baking on one rack.
° After Bake or Convect Bake has been programmed and
activated, press the Rapid Preheat pad.
1 RACK ONLY will display, after 10 seconds the display will
show RAPIDand PREHEAT.
To return to Standard Preheat:
Press Rapid Preheat pad again. This will provide standard
preheat and PREHEATand the selected function will be
displayed. Cant.
18
Notes:
For best results, use rack position 2 or 3 when using the
Rapid Preheat option.
For optimum baking and browning results, Rapid Preheat
is not recommended when baking on multiple racks.
Broil
For optimal results, preheat for five minutes with tile door
closed and use a pan designed for broiling. Oven door should
be open to the broil stop position (about 4 inches) when
broiling.
To set Broil:
1. Placethe oven rack in the proper rack position (see
Broiling Chart).
2. Pressthe Broil pad. Broil :
3. Select HIGH - 550° Ffor high broil. "...................."
OR
Select LOW - 450° Ffor low broil.
4,
5.
The oven has a variable broil feature which means that
a lower broil temperature can be selected (3000-550° El.
To select a lower temperature, press the appropriate
number pads. Press Enter pad to set the lower
ternperature.
Preheat the oven for five minutes.
Placefood in the oven and close the door to the broil stop
position.
j ..........
Pressthe CANCEL pad when broiling : CANCEL
isdone. ...........
Notes:
° See Broiling Chartfor foods and broiling times.
If more than 30 seconds elapse between pressing the Broil
pad, Quickset pads, or number pads, the oven will not be
set and the display will return to the previous display.
° HIGH isused for most broiling. Use a lower broil
temperature when broiling longer-cookingfoods. The
lower temperature allows food to cook to the well done
stage without excessive browning.
° Expect broil times to increaseand browning to be slightly
lighter ifthe appliance is installedon a 208 volt circuit.
Food should be turned halfway through broiling time.
Broil times may be longer when lower broiling
temperatures are selected.
Broiling Chart
Beef (broiled to 165° F)
6 Hamburgers, 1/2" thick
2 Ribeye Steaks, 1" thick
2 New York Strip Steaks, 1" thick
2 T-Bone Steaks, 1" thick
Poultry (broiled to 170° Fon Low)
4 Boneless/Skinless Breasts
4 Bone-In Chicken Breasts
Pork (broiled to 160° F)
4 Boneless Pork Chops, 1" thick
4 Bone-In Pork Chops, 1" thick
Ham Slice, 1"thick
Fish (broiled to 140° El
4 Swordfish Steaks, 1" thick
2 Halibut Steaks, 1" thick
Orange Roughy, 1 "thick
Shrimp (16-20 ct. per lb.)
2 Salmon Fillets, 1/2" thick
2 Salmon Steaks, 1" thick
m
i i i i i i i i i i i i i i iiiiiiiiiiii i i i!! ! ! i !i iii!!i!i!i!i!!iiiii i !i i! ! !! ! ! !!!!!i! i! i! i! !!!!!!!iiiii!i!ii!ii!i!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!! i i
10 - 12 minutes
18 - 22 minutes
18 - 22 minutes
18 - 22 minutes
Low Broil
12 - 15 minutes
20 - 33 minutes
20 - 28 minutes
25 - 28 minutes
12 - 16 minutes
10- 14 minutes
10- 14 minutes
10 - 12 minutes
8 - 10 minutes
8 - 12 minutes
10- 14 minutes
4
4
4
4
4
3
4
4
4
3
3
4
4
4
3
*Important: To reduce browning and excess smoke when broiling, usea lower rack position and increase
the broil time.
19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88

Jenn-Air JGS9900BDB Manuale del proprietario

Tipo
Manuale del proprietario
Questo manuale è adatto anche per