Key Automation 580CT20324W Manuale utente

EN

CBX20324

Control unit for two 24 Vdc motors, for swing gates

Steuergerät für zwei Drehtor-Motoren 24 Vdc

Centrale per due motori 24 Vdc, per cancelli a battente

Logique de commande pour deux moteurs 24 Vdc, pour portails battants

Central para dos motores de 24 Vdc para puertas de batiente

Unidade para dois motores 24 Vdc, para portões de batente

Centrala dla dwóch silników 24 Vdc, do bram skrzydłowych

Motoriduttore interrato

Under grounded gear motor

Motoreducteur enterré

Motorreductor interrado

Unrterflur-Drehtorantrieb

Motorredutor interrado

Podziemny motoreduktor

UNDER

Istruzioni ed avvertenze per l’installazione e l’uso

Instructions and warnings for installation and use

Instrucciones y advertencias para su instalación y uso

Anleitungen und Hinweise zu Installation und Einsatz

Instruções e advertências para a instalação e utilização

Instructions et avertissements pour l’installation et l’usage

Management

System

ISO 9001:2008

www.tuv.com

ID 9105043769

ON

EDGE

PH2

PH1

Instructions and warnings for installation and use

Anleitungen und Hinweise zu Installation und Einsatz

Istruzioni ed avvertenze per l’installazione e l’uso

Instructions et avertissements pour l’installation et l’usage

Instrucciones y advertencias para su instalación y uso

Instruções e advertências para a instalação e utilização

Instrukcje i zalecenia dotyczące instalacji i użytkowania

EN

2

1

2

3

4

5

6

7

8

Safety warnings

2.1

2.2

2.3

2.4

4.1

4.2

4.3

4.4

4.5

4.6

4.7

5.1

5.2

Product Introduction

Description of the control unit

Description of the connections

Models and technical characteristics

List of cables required

Preliminary Checks

Installing the Product

Electric connections

Disabling the safety devices

Display during normal operation

Autolearning of the travel stroke

Learning a trasmitter

Default procedure

Customising the system - BASIC MENU

Testing and commissioning

Testing

Commissioning

Further details - ADVANCED MENU

Instructions and warnings for the

nal user

EU declaration of conformity

pag. 3

pag. 4

pag. 5

pag. 6

pag. 7

pag. 9

pag. 11

pag. 12

pag. 13

pag. 14

pag. 16

pag. 108

TABLE OF CONTENTS

EN

3

ATTENTION !

ORIGINAL INSTRUCTIONS - important safety instructions.

Compliance with the safety instructions below is important for

personal safety. Save these instructions.

Read the instructions carefully before proceeding with installation.

The design and manufacture of the devices making up the

product and the information in this manual are compliant with

current safety standards. However, incorrect installation or

programming may cause serious injury to those working on or

using the system. Compliance with the instructions provided

here when installing the product is therefore extremely impor-

tant.

If in any doubt regarding installation, do not proceed and contact the

Marantec Technical Service for clarications.

Under European legislation, an automatic door or gate system

must comply with the standards envisaged in the Directive

2006/42/EC (Machinery Directive) and in particular standards

EN 12453; EN 12635 and EN 13241-1, which enable declaration

of presumed conformity of the automation system.

Therefore, nal connection of the automation system to the electri-

cal mains, system testing, commissioning and routine maintenance

must be performed by skilled, qualied personnel, in observance of

the instructions in the “Testing and commissioning the automation

system” section.

The aforesaid personnel are also responsible for the tests required

to verify the solutions adopted according to the risks present, and

for ensuring observance of all legal provisions, standards and regu-

lations, with particular reference to all requirements of the EN 12453

standard which establishes the test methods for testing door and

gate automation systems.

Before starting installation, perform the following checks and

assessments:

ensure that every device used to set up the automation system is

suited to the intended system overall. For this purpose, pay spe-

cial attention to the data provided in the “Technical specications”

section. Do not proceed with installation if any one of these devices

is not suitable for its intended purpose;

check that the devices purchased are sucient to guarantee system

safety and functionality;

perform a risk assessment, including a list of the essential safety

requirements as envisaged in Annex I of the Machinery Directive,

specifying the solutions adopted. The risk assessment is one of the

documents included in the automation system’s technical le. This

must be compiled by a professional installer.

Considering the risk situations that may arise during instal-

lation phases and use of the product, the automation system

must be installed in compliance with the following safety pre-

cautions:

never make modications to any part of the automation system

other than those specied in this manual. Operations of this type

can only lead to malfunctions. The manufacturer declines all liability

for damage caused by unauthorised modications to products;

if the power cable is damaged, it must be replaced by the manu-

facturer or its after-sales service, or in all cases by a person with

similar qualications, to prevent all risks;

do not allow parts of the automation system to be immersed in water

or other liquids. During installation ensure that no liquids are able to

enter the various devices;

should this occur, disconnect the power supply immediately and

contact a Marantec Service Centre. Use of the automation system

in these conditions may cause hazards;

never place automation system components near to sources of heat

or expose them to naked lights. This may damage system compo-

nents and cause malfunctions, re or hazards;

all operations requiring opening of the protective housings of va-

rious automation system components must be performed with the

control unit disconnected from the power supply. If the disconnect

device is not in a visible location, ax a notice stating: “MAINTE-

NANCE IN PROGRESS”:

connect all devices to an electric power line equipped with an ear-

thing system;

the product cannot be considered to provide eective protection

against intrusion. If eective protection is required, the automation

system must be combined with other devices;

the product may not be used until the automation system “commis-

sioning” procedure has been performed as specied in the “Auto-

mation system testing and commissioning” section;

the system power supply line must include a circuit breaker device

with a contact gap allowing complete disconnection in the condi-

tions specied by class III overvoltage;

use unions with IP55 or higher protection when connecting hoses,

pipes or cable glands;

the electrical system upstream of the automation system must com-

ply with the relevant regulations and be constructed to good work-

manship standards;

users are advised to install an emergency stop button close to the

automation system (connected to the control PCB STOP input) to

allow the door to be stopped immediately in case of danger;

this device is not intended for use by persons (including children)

with impaired physical, sensory or mental capacities, or with lack

of experience or skill, unless a person responsible for their safety

provides surveillance or instruction in use of the device;

before starting the automation system, ensure that there is no-one

in the immediate vicinity;

before proceeding with any cleaning or maintenance work on the

automation system, disconnect it from the electrical mains;

special care must be taken to avoid crushing between the part ope-

rated by the automation system and any xed parts around it;

children must be supervised to ensure that they do not play with the

equipment.

The automation system component packaging material must

be disposed of in full observance of current local waste dispo-

sal legislation.

The product, being a WEEE, shall not be discarded as unsor-

ted waste but must be sent to separate collection facilities for

recovery and recycling.

Marantec reserves the right to amend these instructions if neces-

sary; they and/or any more recent versions are available at www.

marantec.com

1 - SAFETY WARNINGS

EN

4

2.1 - Description of the control unit

The CBX20324 control unit is the most modern, ecient system for

the control of Marantec motors for the electric opening and closure of

swing gates.

All other, improper, use of the control unit is forbidden. The CBX20324

2.2 - Description of the connections

1- Motor power supply connections

2- Transformer power supply connections

3- 24Vdc and 24Vac output connections to controls and safety

devices

4- Connector for battery charger KBP

5- Connection of ashing light, courtesy light, gate open indicator

light/electric lock

6- Functions display

7- Safety devices dip switches

8- Fuse 2AT slow-acting

9- EDGE-PH2-PH1-OPEN-CLOSE-PAR-SBS safety leds and

input leds

10- STEPPING SBS button ( )

11- UP button ( )

12- MENU button ( )

13- DOWN button and RADIO menu ( )

14- Antenna

15- KEY led

16- Encoder connections

17- Stand-by connections (optional)

2.3 - Models and technical characteristics

has a display allowing easy programming and constant monitoring

of the input status; the menu structure also allows easy setting of

working times and operating modes.

2 - INTRODUCING THE PRODUCT

24 VAC

M1+

M1-

M2+

M2-

COM

FLASH

IND ELEC

LED

v+

ENC M1

ENC M2

NEG

PH POW

EDGE

PH2

PH1

OPEN

CLOSE

SBS

PAR

COM

SHIELD

ANT

POWER

SUPPLY

ON

EDGE

PH2

PH1

BATTERIES

13 1

2

4

35

68 7 15

9

10

12

13

11

14

16

CODE DESCRIPTION

CBX20324H 24V control unit for two swing gate motors in box (trasformer 250 VA)

CBX20324L 24V control unit for two swing gate motors in box (trasformer 150 VA)

CBX20324 24V control unit for two swing gate motors (control unit only)

17

EN

5

3 - PRELIMINARY CHECKS

Before installing the product, perform the following checks and in-

spections:

check that the gate, the door or the barrier is suitable for automation;

the weight and size of the gate or door and the balance of the barrier

boom must be within the operating limits specied for the automa-

tion system in which the product is installed;

check that the gate or door has rm, eective mechanical safety

stops;

make sure that the product xing zone is not subject to ooding;

high acidity or salinity or nearby heat sources might cause the pro-

duct to malfunction;

in case of extreme weather conditions (e.g. snow, ice, wide tempe-

rature variations or high temperatures), friction may increase, cau-

sing a corresponding rise in the force needed to operate the system;

the starting torque may therefore exceed that required in normal

conditions;

check that when operated by hand the gate, the door or the barrier

moves smoothly without any areas of greater friction or derailment

risk;

check that the gate, door or the barrier is well balanced and will the-

refore remain stationery when released in any position;

check that the electricity supply line to which the product is to be

connected is suitably earthed and protected by an overload and dif-

ferential safety breaker device;

the system power supply line must include a circuit breaker device

with a contact gap allowing complete disconnection in the condi-

tions specied by class III overvoltage;

ensure that all the material used for installation complies with the

relevant regulatory standards.

2.4 - List of cables required

The cables required for connection of the various devices in a stan-

dard system are listed in the cables list table.

The cables used must be suitable for the type of installation; for

example, an H03VV-F type cable is recommended for indoor appli-

cations, while H07RN-F is suitable for outdoor applications.

* If the power supply cable is more than 20 m long, it must be of larger gauge (3x2.5mm2) and a safety grounding system must be installed

near the automation unit

** Two cables of 2 x 0.5 mm2 can be used as an alternative

ELECTRIC CABLE TECHNICAL SPECIFICATIONS

Connection cable maximum allowable limit

Control unit power supply line 1 x cable 3 x 1,5 mm220 m *

Flashing light, courtesy light

Antenna

3 x 0,5 mm2 **

1 x cable type RG58

20 m

20 m (advised < 5 m)

Electric lock 1 x cable 2 x 1 mm210 m

Transmitter photocells 1 x cable 2 x 0,5 mm220 m

Receiver photocells 1 x cable 4 x 0,5 mm220 m

Safety edge 1 x cable 2 x 0,5 mm220 m

Key-switch 1 x cable 4 x 0,5 mm2 ** 20 m

Motor power supply line 1 x cable 2 x 1,5 mm210 m

Encoder power supply line 1 x cable 3 x 0,5 mm210 m

- Power supply with protection against short-circuits inside the con

trol unit and on the connected accessories;

- Obstacle detection;

- Automatic learning of working times;

- Safety device deactivation by means of dip switches: there is no

need to bridge the terminals of safety devices which are not in

stalled - the function is simply disabled by means of a dip switch.

TECHNICAL SPECIFICATIONS CBX20324H CBX20324L CBX20324

Power supply (L-N) 230Vac (+10% - 15%) 50/60 Hz 24 Vdc (+10% - 15%)

Rated power maximum 280W maximum 210W -

Photocell power supply output 24Vdc (without regulation) maximum 250mA

Output for Vac accessories power/device test power Vdc 24 Vac without regulation 200 mA / 24 Vdc without regulation 250 mA

Flashing light output 24Vdc (without regulation) 15W

Courtesy light output 24Vdc (without regulation) 15W

Electric lock output 12Vac 15VA maximum

Gate open warning light output 24Vdc (without regulation) 5W

Antenna input 50Ω type cable RG58

Operating temperature -20°C + 55°C

Accessory fuses 2AT

Power supply line fuses 1.6AT -

Max. number of transmitters storage

Compatible with all Marantec “Bi-Linked” transmitters 200

Use in particularly acid, saline or explosive atmospheres NO

Protection class IP54 IPXX

Control unit dimensions 222 x 110 x 275 H mm

Weight 3,93 kg 245 g

EN

6

4 - PRODUCT INSTALLATION

4.1 - Electrical connections

WARNING - Before making the connections, ensure that the control unit is not powered up.

MOTOR CONNECTION

Power supply connection terminal board

M1 + Power supply of motor M1 +

M1 - Power supply of motor M1 -

M2 + Power supply of motor M2 +

M2 - Power supply of motor M2 -

V+ Power supply of Encoder +

ENC M1 Encoder connections M1

ENC M2 Encoder connections M2

NEG Power supply of Encoder -

POWER SUPPLY CONNECTOR

L Power supply live 230 Vac 50-60 Hz

N Power supply neutral 230 Vac 50-60 Hz

Earth

DIP SWITCH

This procedure avoids to bridge the terminal board inputs.

Set on “ON” to disable inputs EDGE, PH1, PH2

WARNING - with the dip switch ON, the safety devices are

disabled.

To disable, follow the procedure at par. 4.2

PHOTOTEST

OUTPUT LED

OPEN

PHOTOCELL 1

PHOTOCELL 2

CLOSE

PARTIAL

STEP BY STEP

COMMON

STOP/EDGE

INDICATOR

NEGATIVE

24 VAC

M1 M2

234

112

234

112

TX RX

PHOTO-1

NC

N

L

COMMON

FLASH

24 VAC

M1+

M1-

M2+

M2-

COM

FLASH

IND ELEC

LED

v+

ENC M1

ENC M2

NEG

+ ALIM. ENCODER

- ALIM. ENCODER

ENCODER 1

ENCODER 2

NEG

PH POW

EDGE

PH2

PH1

OPEN

CLOSE

SBS

PAR

COM

SHIELD

ANT

POWER

SUPPLY

GND

12/24 AC/DC

GND

12/24 AC/DC

COM

OUT

NC

COM

OUT

GND

12/24 AC/DC

GND

12/24 AC/DC

TX RX

PHOTO-2

ON

EDGE

PH2

PH1

PHOTOTEST

OUTPUT LED

OPEN

PHOTOCELL 1

PHOTOCELL 2

CLOSE

PARTIAL

STEP BY STEP

COMMON

STOP/EDGE

INDICATOR

NEGATIVE

24 VAC

M1

M2

N

T1,6A

L

230Vac

50/60Hz

COMMON

FLASH

24 VAC

M1+

M1-

M2+

M2-

COM

FLASH

IND ELEC

LED

v+

ENC M1

ENC M2

NEG

+ ALIM. ENCODER

- ALIM. ENCODER

ENCODER 1

ENCODER 2

NEG

PH POW

EDGE

PH2

PH1

OPEN

CLOSE

SBS

PAR

COM

SHIELD

ANT

POWER

SUPPLY

TX RX

PHOTO-1

GND

12/24 AC/DC

GND

12/24 AC/DC

COM

OUT

NC

COM

OUT

GND

12/24 AC/DC

GND

12/24 AC/DC

TX RX

PHOTO-2

NC

234

112

234

112

ON

EDGE

PH2

PH1

ELECTRICAL CONNECTIONS

FOR ENERGY SAVING

WARNING - The motor and the encoder cables must be

separated

*To enable STAND BY see paragraph 4.7 point 12. Only during this function PHOTOTEST is not possible

EN

7

SAFETY AND CONTROL DEVICE CONNECTORS

24 VAC Accessories power supply 24 Vac without regulation, 200 mA (with battery operation output not active)

COM Common for the FLASH-IND-LED outputs

FLASH Flashing light output 24Vdc (without regulation), maximum 15W

IND/ELEC IND output for gate open indicator light 24 Vdc not regulated 5W MAX / Electric lock output 12Vac, 15VA maximum

selectable with parameter indic light.

LED Courtesy light output 24Vdc (without regulation), maximum 15W, controllable also via radio ON-OFF command

NEG Photocell and encoder power supply negative

PH-POW Photocells PH1 and PH2 power supply positive; phototest can be selected with parameter PHOTO TEST24 Vdc, 250

mA

EDGE STOP

EDGE safety device, NC contact between EDGE and EDGE (warning, with dip switch 1 ON the safety device input is

o). This input is classied as a safety device; the contact can be deactivated at any time, cutting out the automation

system and disabling all functions, including Automatic Closure.

Safety sensor edge, ON/OFF, NC contact or resistive 8K2 between EDGE and EDGE.

Input selectable with parameter TYPE EDGE

PH2

Photocells (opening), NC contact between PH2 and COM (warning, with dip switch 2 ON the PHOTOCELL 2 safety

device input is o). The photocell is tripped at any time during opening of the automation system, halting operation

immediately; the automation system will continue opening when the contact is restored. In the event of intervention on

closure (parameter FOTO2 SETUP= 0) the device stops and on release re-opens

PH1

Photocells (closing), NC contact between PH1 and COM (warning, with dip switch 3 ON the PHOTOCELL 1 safety

device input is o) The photocell is tripped at any time during closing of the automation system, halting operation im-

mediately and reversing the travel direction

OPEN OPEN command NO contact between OPEN and COM

Contact for the HOLD-TO-RUN function. The gate OPENS as long as the contact is held down

CLOSE CLOSE command NO contact between CLOSE and COM

Contact for the HOLD-TO-RUN function. The gate CLOSES as long as the contact is held down

PAR PARTIAL command NO contact between PAR and COM

Used to open the gate partially, depending on the software setting

SBS STEPPING command NO contact between SBS and COM

Open/Stop/Close/Stop command, or as set in the software

COM Common for the PH2-PH1-OPEN-CLOSE-PAR-SBS inputs

SHIELD Antenna - shield -

ANT Antenna - signal -

4.3 - Display during normal operation

In “NORMAL OPERATING MODE”, i.e. when the system is powered up normally, the 5-gure LCD display shows the following status messages

(to compare with the previous elettronic board CBX20224 check the second column):

CBX20324 OLD CBX20224 MEANING

MOTOR SETUP Motor type not selected

LEARN TO DO Learning not done

READY -- Gate closed or switch-on after shutdown

ìOPEN ING OP Gate opening

CLOs ING CL Gate closing

STOP OPEN SO Gate stopped during opening

PHOTO 1

The PHOTO1 contact must be connected to the COM and PH 1

terminals. To bypass the photocell, move the right-hand dip

switch upwards. After having activated the dip switch, the

PH1 LED starts to ash at a fast rate.

ATTENTION! CONFIRM INPUT PH1 DEACTIVATION BY

PRESSING THE AND BUTTONS SIMULTANEOUSLY

AND HOLDING THEM DOWN UNTIL THE PH1 LED STOPS

FLASHING.

4.2 - Disabling the safety devices

EDGE

The inputs of the safety EDGE must be connected to the EDGE

and EDGE terminals. To bypass the safety edge, move the

left-hand dip switch upwards. After having activated the dip

switch, the EDGE LED starts to ash at a fast rate.

ATTENTION! CONFIRM INPUT EDGE DEACTIVATION

BY PRESSING AND BUTTONS SIMULTANEOUSLY

AND HOLDING THEM DOWN UNTIL THE EDGE LED STOPS

FLASHING.

PHOTO 2

The PHOTO2 contact must be connected to the COM and PH

2 terminals. To bypass the photocell, move the middle dip

switch upwards. After having activated the dip switch, the

PH2 LED starts to ash at a fast rate.

ATTENTION! CONFIRM INPUT PH2 DEACTIVATION BY

PRESSING THE AND BUTTONS SIMULTANEOUSLY

AND HOLDING THEM DOWN UNTIL THE PH2 LED STOPS

FLASHING.

EN

8

Malfunctions

This section lists a number of malfunctions which may occur.

EVENT DESCRIPTION FLASH LIGHT AND KEY LED

SIGNALS

opening Gate opening

closure Gate closing

automatic closure Gate open with timed reclosure active

stop during closure Gate stopped during closure

stop during opening Gate stopped during opening

open Gate completely open without automatic reclosure

closed Gate completely closed

autolearning During the programming phase 2 quick ashes + pause + 1 ash

obstacle M1/M2 Motor 1/2 obstacle detected 4 quick ashes + pause, 3 times

photo 1! / photo 2! Photocell 1 tripped / Photocell 2 tripped 2 quick ashes + pause, 3 times

safety edge! Safety edge tripped 5 quick ashes + pause, 3 times

partial opening Partial opening in progress

automatic partial closure Gate opening to partial position with timed reclosure activated

realignment Realignment after a manual release

phototest error Phototest error detected 3 quick ashes + pause, 3 times

IND/ELEC error Electric lock / gate open light line overload 6 quick ashes + pause, 3 times

encoder error Encoder error detected (Encoder do not respond) 7 quick ashes + pause, 3 times

SURGE OVERLOAD ALARM The motor’s current drawdown has increased very quickly

OVER LOAD1 1. The gate has hit an obstacle (M1)

2. There is friction on the leaf of M1

OVER LOAD2 1. The gate has hit an obstacle (M2)

2. There is friction on the leaf of M2

STOP CLOSE SC Gate stopped during closure

FOTO1 F1 Photocell 1 tripped

FOTO2 F2 Photocell 2 tripped

ALIGN MENT ALI Re-alignment procedure

OPEN oP Gate open without automatic reclosure

PAR TIAL OPD Gate in partial opening mode

PART OPEN Pe Gate in partial opening position without automatic reclosure

TIME CLOSE -tC Gate open with timed reclosure

Flashing dash counting in progress

Dash replaced by gures 0..9 countdown (last 10s)

TIME PART -tP Gate in partial opening position with timed reclosure

Flashing dash counting in progress

Dash replaced by gures 0..9 countdown (last 10s)

ERROR LEARN L-- Learning stopped due to activation of safety device or motor reverse

OPEN1 LEARN LOP Learning on M1 opening

OPEN2 LEARN LO.P.Learning on M2 opening

CLOS1 LEARN LCL Learning on M1 closing

CLOS2 LEARN LC.L.Learning on M2 closing

OPEN1 SLOW SOP Point of M1 deceleration on opening (only during stroke learning)

OPEN2 SLOW SO.P.Point of M2 deceleration on opening (only during stroke learning)

CLOS1 SLOW SCL Point of M1 deceleration on closing (only during stroke learning)

CLOS2 SLOW SC.L.Point of M2 deceleration on closing (only during stroke learning)

SAFETY EDGE ALARM The control unit has received a signal from the safety edge

EDGE 1. The safety edge has been pressed.

2. The safety edge is not connected correctly

EN

9

After eliminating the cause of the alarm, to delete all errors simply press a button.The display returns to the normal screen.

Press “UP“ to read the following parameters on display.

PHOTOCELL ALARM/SAFETY EDGE Phototest fail outcome

FOTO TEST 1. Check the photocell and the safety edge connections

2. Check that the photocells and the safety edge are operating correctly

DISPLAY MEANING

Status display ( ready, opening... etc) Description of the control unit ( ready, opening... etc)

Maneuvers performed Counter displays alternating ncy and the number of cycles

Motor current 1 [mA] Motor current absorption (e.g. i m1=1500)

Motor current 2 [mA] Motor current absorption (e.g. i m2=1500)

Firmware version and serial number E.g. ct20324W - fw1.0 - sn635a33f1

4.4 - Autolearning of the travel stroke

The rst time the control unit is powered up, an autolearning procedure must be carried out to acquire fundamental parameters such as the

travel stroke length and deceleration points.

ATTENTION! ONLY during the rst installation the display will show motor SETUP, to select the type of motor installed.

Select the type of motor with (UP) and (DOWN-RADIO) and conrm by keeping the (MENU) button pressed until DONE

appears on the display: 1 = RA2224E, 2 = RE2224, 3 = UN24E, 4 = ST3024, 5 = RA4224E / ST5024

The display shows LEARN TO DO. Proceed with the autolearning of the travel stroke as follows.

Before starting the procedure, check if MOTOR 1 (M1) is on the left or right side of the gate: MOTOR 1 (M1)will always be the rst to open.

All the main parameters are set with the default settings by the control unit. To customize the installation, proceed as described below.

AUTOLEARNING OF THE TRAVEL STROKE

The decelerations will be those set in the menu, with the same percentage during both opening and closing.

CAUTION: if manual programming of deceleration intervals is required, go to the next table

CAUTION! check that mechanical end stops (compulsory) are present and secure. The motors must

always reach the mechanical end stop

1. Move the gate manually to mid-travel

CAUTION: In case that only 1 motor connected, before starting the procedure, change the parameter 13

(1/2 motors) before starting the learning procedure.

3. Press the buttons (UP) and (MENU) at the same time for at least 5 seconds until OPEN1 is di-

splayed, see the gure.

Ensure that motor M1 is activated rst; otherwise, press (DOWN-RADIO), turn the power o and invert

connections M1 and M2. Repeat the procedure from step 3.

If the rst manoeuvre is NOT opening, press (DOWN-RADIO) to stop the self-learning process. Then

press (SBS) to restart acquisition: the leaf resumes movement in the correct direction

4. Motor M1 opens at low speed until it reaches the mechanical opening end stop.

On reaching the mechanical end stop in opening of M1 motor M2 starts automatically in opening mode (the

display shows OPEN2 LEARN.). If motor M2 moves in closing, stop by pressing (DOWN-RADIO) and

resume movement using (the leaf resumes movement in the correct direction)

5. The motor M2 opens at low speed until reaching the mechanical opening end stop.

6. After a couple of seconds, motor M2 starts closing automatically at low speed until reaching the mechanical

closing end stop (the display shows CLOS2 LEARN.)

7. On reaching the mechanical closing end stop of M2, motor M1 closes at low speed until reaching the mecha-

nical closing end stop, thus completing the programming phase (the display shows CLOS1 LEARN)

RADIO

M2M1

ENCODER ALARM Encoder do not respond

enc error 1. Check the encoder connection

2. Check that the encoder is operating correctly

LEARN TO DO

EN

10

AUTOLEARNING OF THE TRAVEL STROKE WITH CUSTOMISED DECELERATIONS

Deceleration intervals can be customized by the user, according to the procedure below

CAUTION! check that mechanical end stops (compulsory) are present and secure. The motors must

always reach the mechanical end stop

1. Move the gate manually to mid-travel

CAUTION: In case that only 1 motor connected, before starting the procedure, change the parameter 13

(1/2 motors) before starting the learning procedure.

3. CAUTION: enter the BASIC MENU to set the parameter lengh slow = 0 as in the table in paragraph 4.6

4. Press the buttons (UP) and (MENU)at the same time for at least 5 seconds until open1 learn is

displayed, then (if necessary) press (DOWN-RADIO) (see gure).

Ensure that motor M1 opens rst; otherwise, press (DOWN-RADIO), turn the power o and invert con-

nections M1 and M2. Repeat the procedure from step 4.

If the rst manoeuvre is NOT opening, press (DOWN-RADIO) to stop the self-learning process.

Then press (SBS) to restart acquisition: the leaf resumes movement in the correct direction

5. Motor M1 opens at low speed until it reaches the mechanical opening end stop.

On reaching the mechanical end stop in opening of M1 motor M2 starts automatically in opening mode (the di-

splay shows open2 learn.). If motor M2 moves in closing, stop by pressing (DOWN-RADIO) and resume

movement using (SBS). The leaf resumes movement in the correct direction.

6. The motor M2 opens at low speed until reaching the mechanical opening end stop. After a couple of seconds,

the motor M2 closes at low speed (the display shows clos2 learn)

7. On reaching the point where motor M2 closing deceleration is required, press (SBS). M2 motor

movement continues at low speed (the display shows clos2 slow.)

8. On reaching the mechanical end stop of motor M2, motor M1 starts closing

9. M1 starts closing. On reaching the point where motor M1 closing deceleration is required, press

(SBS). M1 motor movement continues at low speed (the display shows clos1 slow)

10. When motor M1 reaches the closed position, motor M1 stops and restarts opening

11. On reaching the point where motor M1 opening deceleration is required, press (SBS). M1 motor

movement continues at low speed (the display shows open1 slow)

12. When motor M1 reaches the open position, motor M1 stops and motor M2 starts in opening

13. On reaching the point where motor M2 opening deceleration is required, press (SBS). M2 motor

movement continues at low speed. (the display shows open2 slow.)

14. When motor M2 reaches the open position, motor M2 stops

15. M1 and M2 resume closing according to the oset parameter entered in the menu, i.e. the gate closes auto-

matically according to the set travel

16. Run a number of opening, closing and stop manoeuvres, to check that the system is stable and there are no

assembly defects. The deceleration points not assigned manually will be automatically set at 20% of the control

unit stroke

-

LEARN TO DO

RADIO

M2M1

EN

11

(<3s) ->

3s

4.5 - Learning a transmitter

A transmitter can be memorized via the specic programming menu or by remote memorisation, using a previously memorised transmitter.

CLEARING THE ENTIRE RECEIVER MEMORY

If you are in programming mode, press the (MENU) button to exit until ready appears. Press the

(DOWN-RADIO) button for more than 2 seconds. Until the display shows the word radio menuì (radio), then

release the button

1. Press the (DOWN-RADIO) button and hold it down until the LED lights up (about 3 seconds) and then goes

out (about 3 seconds). Release the button. (>3s)-> (>3s)->

2. About 1 second after the button is released, the KEY LED starts to ash (1s)+ (1s)+

3. Press the (DOWN-RADIO) button as the LED ashes for the third time

4. If the deletion has been successful, the KEY LED will give one long ash 3s

MEMORISING A REMOTE CONTROL

If you are in programming mode exit pressing the (MENU) button until ready appears. Press the

(DOWN-RADIO) button for more than 2 seconds. Until the display shows the word radio menuì (radio), then

release the button

1. Press and release the (DOWN-RADIO) button a number of times equal to the number of the function to

be selected: once for function STEP BY STEP (LEARN SBS), twice for function PARTIAL (LEARN PAR), three

times for function ONLY OPEN (LEARN OPEN), four times for function LIGHT ON/OFF (LEARN LIGHT) + +

2. The KEY LED will ash a number of times equal to the number of the function selected, with 1 second pauses

between ashes +1s +1s

3. Within 7 seconds press the button (for 2 seconds) of the remote control to be memorized 2s

4. If the memorization has been successful, the KEY LED will give one long ash 3s

5. To memorize another remote control on the same function, repeat point 3

N.B If no commands are given for 7 seconds, the receiver automatically quits the programming mode

DELETING A REMOTE CONTROL

If you are in programming mode, press the (MENU) button to exit until ready appears. Press the

(DOWN-RADIO) button for more than 2 seconds. Until the display shows the word radio menuì (radio), then

release the button

1. Press the (DOWN-RADIO) button until the LED lights up (about 3 seconds), then release the button

2. Within 7 seconds press the button of the remote control to be deleted, holding it down until the KEY LED goes

out. Release the remote control button

3. About 1 second after the button is released, the KEY LED starts to ash (1s)+ (1s)+

4. Conrm the deletion by pressing the - (DOWN-RADIO) button

5. If the deletion has been successful, KEY LED will give one long ash

N.B If no commands are given for 7 seconds, the receiver automatically quits the programming mode

►

3s

4.6 - Default procedure

The default procedure will reset the system to the factory settings and, if necessary, will allow to change the motor type.

To proceed, enter the ADVANCED MENU: press and hold for 5 sec. the (MENU) button. Scroll the menu with (UP) or (DOWN-RA-

DIO) until motor SETUP appears.

Press the (MENU) button for 1 sec. to see the type of motor selected

ATTENTION! ONLY if you need to change the type of motor, change the number with (UP) or (DOWN):

1 = RA2224E, 2 = RE2224, 3 = UN24E, 4 = ST3024, 5 = RA4224E / ST5024

Press and hold the (MENU) button, a countdown starts: 49, 48, …, 1 until DONE appears. Release the button.

EN

12

CBX20324 OLD CBX20224 DESCRIPTION DEFAULT MIN MAX UNIT

1auto close TCL Automatic reclosure time (0 = o) 0 0 900 s

2photo close ttr Reclosing time after transit on PH1

(0 = o) 0 0 30 s

3react time SEI

Force on obstacles

0 = Maximum impact force

10 = Minimum impact force

3 0 10

4open speed SFO

Motor speed during opening

1 = minimum

2 = low

3 = medium

4 = high

5 = maximum

4 1 5

5sl-op speed SSO

Motor speed during opening deceleration phase

1 = minimum

2 = low

3 = medium

4 = high

5 = maximum

1 1 5

6close speed SFC

Motor speed during closing

1 = minimum

2 = low

3 = medium

4 = high

5 = maximum

4 1 5

7sl-cl speed SSC

Motor speed during closing deceleration phase

1 = minimum

2 = low

3 = medium

4 = high

5 = maximum

1 1 5

4.7 - Customising the system - BASIC MENU

If necessary, users may select a BASIC MENU which allows modi-

cation of the control unit’s basic parameters. To select the BASIC

MENU proceed as described below.

WARNING: to be certain of accessing the NORMAL OPERATION

display state, the starting point for accessing the BASIC MENU,

press the (MENU) button twice

Exampling of modifying a BASIC MENU parameter

After accessing the BASIC

MENU, press the (UP)

and (DOWN) button to

scroll through the functions.

Press the (MENU) button

quickly to quit the menu.

Press the (MENU) button

for 1 second to access the ba-

sic menu.

Press the + (UP) or - -UP

(DOWN) buttoms to scroll

through the functions to mo-

dify other parameters.

Press the or buttons to

to modify the value.

Press the + (MENU) button

for more than 1 second (LONG

PRESS) to save the modied

value. The value stops a-

shing. Alternatively, press the

+ (MENU) button QUICKLY to

quit the function without saving.

To access the value modi-

cation function, press the

(MENU) button for 1 second,

until the value starts to ash

quickly.

ready auto close

auto close ready

EN

13

8SBS setup SBS

STEP BY STEP or SBS conguration:

0 = Normal (AP-ST-CH-ST-AP-ST…)

1 = Alternate STOP (AP-ST-CH-AP-ST-CH…)

2 = Alternate (AP-CH-AP-CH…)

3 = Apartment block – timer

(set TIME CLOSE ≠ 0)

4 = Apartment block with immediate reclosure

0 0 4

9delay leaf2 DLY Second leaf delay on opening 2 0 300

10 lengh slow LSI

Deceleration distance

1 to 100 = Motor deceleration percentage during

opening and closure

P= customized decelerations

20 1 100 %

11 black out BlT

Post blackout procedure

0 = No action, remains stationery

1 = Closure

0 0 1

12 stand by SBY

Energy saving: enables photocell switch-o

when gate is closed (only during this function

PHOTOTEST is not possible)

0= disabled

1= enabled

0 0 1

13 1/2 motor nMt

Number of motors

1 = 1 motor

2 = 2 motors

2 1 2

5.2 Commissioning

Once all (and not just some) of the system devices have passed the

testing procedure, the system can be commissioned;

the system’s technical dossier must be produced and kept for 10

years. It must contain the electrical wiring diagram, a drawing or

photograph of the system, the analysis of the risks and the solutions

adopted to deal with them, the manufacturer’s declaration of con-

formity for all connected devices, the operator’s manual for every

device and the system maintenance plan;

x a dataplate with the details of the automation, the name of the

person who commissioned it, the serial number and year of con-

struction and the CE marking on the gate or door;

also t a sign specifying the procedure for releasing the system by

hand;

draw up the declaration of conformity, the instructions and precau-

tions for use for the end user and the system maintenance plan and

consign them to the end user;

ensure that the user has fully understood how to operate the system

in automatic, manual and emergency modes;

the end user must also be informed in writing about any risks and

hazards still present;

WARNING - after detecting an obstacle, the gate or door stops du-

ring its opening travel and automatic closure is disabled; to restart

operation, the user must press the control button or use the tran-

smitter.

5 - TESTING AND COMMISSIONING THE AUTOMATION SYSTEM

5.1 Testing

All system components must be tested following the procedures de-

scribed in their respective operator’s manuals;

ensure that the recommendations in Chapter 1 - Safety Warnings -

have been complied with;

check that the gate or door is able to move freely once the automa-

tion system has been released and is well balanced, meaning that it

will remain stationery when released in any position;

check that all connected devices (photocells, safety edges, emer-

gency buttons, etc.) are operating correctly by performing gate or

door opening, closing and stop tests using the connected control

devices (transmitters, buttons or switches);

perform the impact measurements as required by the EN12453

standard, adjusting the control unit’s speed, motor force and de-

celeration functions if the measurements do not give the required

results, until the correct setting is obtained.

The system must be tested by a qualied technician, who must

perform the tests required by the relevant standards in relation to

the risks present, to check that the installation complies with the

relevant regulatory requirements, especially the EN 12453 standard

which species the test methods for gate and door automation sy-

stems.

EN

14

EN

6 - FURTHER DETAILS - ADVANCED MENU

CBX20324 OLD

CBX20224 DESCRIPTION DEFAULT MIN MAX UNIT

1foto1 setup SP.h.Use of PHOTO1 when starting from closed

0 = PHOTO1 is checked

1 = The gate starts even with PHOTO1 excited

1 0 1

2foto2 setup Ph.2.Use of PHOTO2

0 = Enabled during both opening and closing AP/CH

1 =Only enabled during opening AP

0 0 1

3photo test tP.h.

Photo-device test

0 = o

1 = PHOTO1 on

2 = PHOTO2 on

3 = PHOTO1 and PHOTO2 on

0 0 3

4type edge Ed.m.

STOP/EDGE input selection

0 = STOP contact (NC)

1 = Resistive safety edge (8k2)

2 = Contact safety edge (NC)

0 0 2

5setup edge iE.D.

Safety edge tripping mode

0= only tripped during closure with total direction reversal

1 = stops the automation (during both opening and

closure) and retreats from the obstacle for 2 seconds

2 = stops the automation (during both opening and

closure) and retreats from the obstacle for a SHORT time

0 0 1

6test edge tE.D.Edge test

0 = o

1 = on

0 0 1

7setup part LP.o.Partial opening 50 0 100 %

8close part TP.C.Time for automatic closure from partial opening (0=o) 0 0 900 s

9flash setup FP.r.Flashing light output setup

0 = Fixed

1 = Flashing

1 0 1

10 pre setup

Beavior pre ashing

(disable if PRE TIME=0)

0=before an opening or closing manoeuvre

1=before a closing manoeuvre

2=before an opening manoeuvre

0 0 2

11 pre time tP.r.Pre-ashing time (0 = o) 0 0 20 s

12 setup light FC.Y.

Courtesy light setup

0 = On at end of operation for time TIME LIGHT

1 = On if gate not closed + duration of TIME LIGHT

2 = On if courtesy light timer TIME LIGHT time not out

0 0 2

13 time light tC.Y.Courtesy light time 0 0 900 s

14 hold torun de.a.Hold-to-run

0 = o

1 = on

0 0 1

15 indic light IN.D.

0 = deactivated

1 = gate open light ON/OFF

2 = gate open light proportional

- Slow ashing with gate opening

- Quick ashing with gate closing

- Fixed light if gate open

- 2 ashes + pause with gate stationary (position other

than closed)

3 = Electric lock

4 = Magnetic electric lock function with output active when

gate/door is closed

N.B. interface with an external relay with 24 Vdc winding.

To activate this function, the pre-ash must be enabled at

the recommended value of 1 sec (pre flash ≠ 0)

0 0 4

The ADVANCED MENU allows the system to be further customi-

sed by modifying parameters not accessible from the basic menu.

To access the ADVANCED MENU, press the MENU key and hold

it down for 5 seconds.

To modify ADVANCED MENU parameters, proceed as described

for the BASIC MENU.

N.B. Some default functions/display items may vary with respect to

the type of motor selected.

EN

15

16 cycle servi se.r.Service interval cycle threshold

(0 = o) 10 0 200 x 1000

cycles

17 setup servi se.f.

Enabling of continuous ashing indicating service

required with cycle servi ≠ 0 (only active with gate

closed)

0 = o

1 = on

0 0 1

18 elect time EL.T.Electric lock activation time in seconds 2 1 10 s

19 el-op setup HA.o.Water hammer on opening

0 = disabled 0 0 100 *100ms

20 el-cl setup HA.c.Water hammer on closing

0 = disabled 0 0 100 *100ms

21 relea time rE.L.

Motor release from closed/open stops. Useful for

lightweight gates

0 = o

1 to 10 release levels (1 = minimum release, 10 =

maximum release)

0 0 10

22 boost setup ST.P.High-speed motor start-up

0 = o

1 = on

0 0 1

23 delay leaf1 dm.I.Leaf 1 closing delay with gate open

0 = o

1 = 1 to 20 Seconds On

1 0 20

24 encod setup En.C.0= o (virtual encoder)

1= on (physical encoder) 0/1 0 1

25 motor setup DE.F.

Reset to default values:

1= RA2224E

2= RE2224

3= UN24E

4= ST3024

5= RA4224E / ST5024

1 1 4

EN

16

Marantec Marienfeld GmbH & Co. KG produces systems for the

automation of gates, garage doors, automatic doors, roller blinds

and car-park and road barriers. However, Marantec is not the ma-

nufacturer of your complete automation system, which is the outco-

me of the analysis, assessment, choice of materials and installation

work of your chosen installer. Every automation system is unique,

and only your installer has the experience and skill required to pro-

duce a safe, reliable, durable system tailored to your needs, and

above all that complies with the relevant regulatory standards. Al-

though your automation system complies with the regulation safety

level, this does not rule out the presence of “residual risk”, meaning

the possibility that hazards may occur, usually due to reckless or

even incorrect use. We would therefore like to give you some advi-

ce for the correct use of the system:

• before using the automation system for the rst time, have the

installer explain the potential causes of residual risks to you;

• keep the manual for future reference, and pass it on to any new

owner of the automation system;

• reckless use and misuse of the automation system may make it

dangerous: do not operate the automation system with people, ani-

mal or objects within its range of action;

• a properly designed automation system has a high level of safety

, since its sensor systems prevent it from moving with people or ob-

stacles present so that its operation is always predictable and safe.

However, as a precaution children should not be allowed to play clo-

se to the automation system, and to prevent involuntary activation,

remote controls must not be left within their reach;

• as soon as any system malfunction is noticed, disconnect the

electricity supply and perform the manual release procedure. Never

attempt repairs on your own; call in your installation engineer. In

the meantime the door or gate can be operated without automation

once the geared motor has been released using the release key

supplied with the system. In the event of safety devices out of ser-

vice arrange for repairs to the automation immediately;

• in the event of malfunctions or power failures: while waiting for the

engineer to come (or for the power to be restored if your system is

not equipped with buer batteries), the door or gate can be used just

like any non-automated installation. To do this, the manual release

procedure must be carried out;

• manual release and operation: rst bear in mind that the release

procedure can only be carried out with the door or gate stationery.

• Maintenance: Like any machine, your automation system needs

regular periodic maintenance to ensure its long life and total safety

. Arrange a periodic maintenance schedule with your installation en-

gineer. Marantec recommends that maintenance checks should be

carried out every six months for normal domestic use, but this inter-

val may vary depending on the level of use. Any inspection, main-

tenance or repair work must only be carried out by qualied sta.

• Never modify the automation system or its programming and setup

parameters: this is the responsibility of your installation engineer.

• Testing, routine maintenance and any repairs must be recorded by

the person who performs them and the documents must be conser-

ved by the system’s owner.

The only procedures you are capable of, and which you are recom-

mended to perform, are cleaning of the photocell glass and removal

of any leaves or stones that may obstruct the automation system.

To prevent anyone from activating the gate or door, release the au-

tomation system before starting. Clean only with a cloth dipped in

a little water.

At the end of its useful life, the automation system must be dismant-

led by qualied personnel, and the materials must be recycled or

disposed of in compliance with the legislation locally in force.

If after some time your remote control seems to have become less

eective, or stops operating completely, the battery may be at (de-

pending on the level of use, this may take from several months up

to more than a year). You will realise this because the transmission

conrmation light does not come on, or only lights up for a very

short time.

Batteries contain pollutants: do not dispose of them with normal wa-

ste but follow the methods specied by the local regulations.

Thank you for choosing Marantec Marienfeld GmbH & Co. KG; ple-

ase visit our Internet site www.marantec.com for further information.

7 - INSTRUCTIONS AND WARNINGS FOR THE END USER

17

DE

1

2

3

4

5

6

7

8

Sicherheitshinweise

2.1

2.2

2.3

2.4

4.1

4.2

4.3

4.4

4.5

4.6

4.7

5.1

5.2

Einführung in das Produkt

Beschreibung des Steuergerätes

Beschreibung der Anschlüsse

Modelle und technische Eigenschaften

Liste benötigter Kabel

Vorabkontrollen

Produktinstallation

Stromanschlüsse

Deaktivierung der Sicherheitsvorrichtungen

Anzeige Normalmodus

Einlernen des Laufs

Lernfunktion eines Senders

Standardverfahren

Benutzerdenierte Einrichtung der Anlage -

Grundmenü

Test und Inbetriebnahme

Abnahme

Inbetriebnahme

Vertiefung - ERWEITERTES MENÜ

Anweisungen und Hinweise für

den Endbenutzer

EG-Konformitätserklärung

S. 18

S. 19

S. 20

S. 21

S. 22

S. 24

S. 26

S. 27

S. 28

S. 29

S. 31

S. 108

INHALTSVERZEICHNIS

18

DE

1 - SICHERHEITSHINWEISE 1 - SICHERHEITSHINWEISE

ORIGINALANWEISUNGEN – Wichtige Sicherheitsanweisun-

gen. Für die Sicherheit der Personen ist es wichtig, die folgen-

den Sicherheitsanweisungen zu befolgen. Bewahren Sie diese

Anweisungen auf.

Vor Durchführung der Installation lesen Sie die Anleitung bitte auf-

merksam durch.

Die Konstruktion und die Herstellung der Geräte, aus denen

sich das Produkt zusammensetzt, und die in diesem Han-

dbuch enthaltenen Informationen entsprechen den geltenden

Sicherheitsvorschriften. Dennoch können eine falsche Instal-

lation und eine falsche Programmierung schwerwiegende Ver-

letzungen bei Personen verursachen, die die Arbeit ausführen,

und bei denen, die die Anlage benutzen werden. Aus diesem

Grund ist es wichtig, während der Installation strikt alle Anwei-

sungen in diesem Handbuch zu beachten.

Bei Zweifel jeglicher Art die Installation abbrechen und ggf. den Ma-

rantec Kundendienst zur Klärung kontaktieren.

Für die europäische Gesetzgebung muss der Einbau einer au-

tomatischen Tür oder eines automatischen Tors den Bestim-

mungen der Richtlinie 2006/42/EG (Maschinenrichtlinie) und im

Besonderen den Normen EN 12453, EN 12635 und EN 13241-1

entsprechen, die eine Konformitätserklärung der Automatisie-

rung ermöglichen.

In Anbetracht dessen müssen die endgültige Verbindung der Au-

tomatisierung ans Stromnetz, die Endabnahme der Anlage, die In-

betriebnahme und die regelmäßige Wartung von qualiziertem und

erfahrenem Personal entsprechend den Anleitungen unter „Prüfung

und Inbetriebnahme der Automatisierung“ durchgeführt werden.

Außerdem muss das Personal auch die vorgesehenen Tests nach

den vorhandenen Risiken festlegen und die Einhaltung der Geset-

ze, Vorschriften und Regeln überprüfen: insbesondere die Einhal-

tung der Norm EN12453, welche die Prüfverfahren für die Automa-

tisierung von Türen und Toren festlegt.

Vor Installationsbeginn folgende Analysen und Prüfungen dur-

chführen:

Sicherstellen, dass die für die Automatisierung vorgesehenen

Vorrichtungen für die zu realisierende Anlage geeignet sind. Die-

sbezüglich aufmerksam die im Kapitel „Technische Eigenschaften“

aufgeführten Daten prüfen. Die Installation nicht durchführen, wenn

auch nur eine der Vorrichtungen nicht für den Gebrauch geeignet

ist.

Sicherstellen, dass die erworbenen Vorrichtungen ausreichend

sind, um die Sicherheit und Funktion der Anlage zu gewährleisten.

Die Risikoanalyse durchführen, welche auch die Liste der Sicherhei-

tsanforderungen, aufgeführt in Anhang I der Maschinenrichtlinie,

beinhalten muss, und die angewandten Lösungen nennen.Die Ri-

sikoanalyse ist eine der Unterlagen, aus denen sich die technischen

Unterlagen der Automatisierung zusammensetzen. Diese müssen

von einem erfahrenen Installateur ausgefüllt werden.

In Anbetracht der Gefahrensituationen, die bei Installation und

Benutzung des Produktes auftreten können, muss die Automa-

tisierung unter Berücksichtigung folgender Hinweise installiert

werden:

Keine Änderungen an der Automatisierung vornehmen, wenn die-

se nicht in diesem Handbuch vorgesehen sind. Diese können nur

zu Funktionsstörungen führen. Der Hersteller übernimmt keine

Haftung für Schäden, die durch eigenmächtige Änderungen am

Produkt verursacht wurden.

Ist das Stromkabel beschädigt, muss es vom Hersteller, seinem

technischen Kundendienst oder einer ähnlich qualizierten Person

ersetzt werden, um Gefährdungen zu vermeiden;

Die einzelnen Komponenten der Automatisierung dürfen nicht in

Wasser oder andere Flüssigkeiten getaucht werden. Bei der In-

stallation darauf achten, dass keine Flüssigkeit ins Innere der Vor-

richtungen dringt.

Sollten Flüssigkeiten ins Innere der Automatisierungskomponenten

dringen, sofort die Stromzufuhr abschalten und sich an den Maran-

tec Kundendienst wenden. Die Benutzung der Automatisierung in

derartigen Situationen kann gefährlich sein.

Die einzelnen Komponenten weder Wärmequellen noch oenen

Flammen aussetzen. Dadurch können Schäden, Störungen und

Gefahrensituationen entstehen oder ein Brand ausbrechen.

Alle Arbeiten, die ein Önen der Schutzhülle der Komponenten er-

fordern, müssen bei abgeschalteter Stromzufuhr durchgeführt wer-

den. Sollte die Abschaltvorrichtung nicht sichtbar sein, ein Schild mit

der Aufschrift „IN WARTUNG“ anbringen.

Alle Vorrichtungen müssen mit einer Stromleitung verbunden wer-

den, die sicher geerdet ist.

Dieses Produkt kann nicht als ausreichendes System für den Ein-

bruchsschutz angesehen werden. Wenn Sie sich ausreichend

schützen wollen, müssen andere Vorrichtungen in die Automatisie-

rung integriert werden.

Wie im Absatz „Prüfung und Inbetriebnahme der Automatisierung“

vorgesehen, darf das Produkt erst nach der „Inbetriebnahme“ der

Automatisierung benutzt werden.

Im Stromnetz der Anlage eine Abschaltvorrichtung mit ausreichen-

dem Önungsabstand der Kontakte vorsehen, die, wie von der

Überspannungskategorie III gefordert, die komplette Abschaltung

erlaubt.

Verwenden Sie für die Verbindung von steifen und exiblen Rohren

oder Kabeldurchgängen Anschlüsse mit dem Schutzgrad IP55 oder

höher.

Die elektrische Anlage vor der Automatisierung muss den geltenden

Bestimmungen entsprechen und fachgerecht ausgeführt sein.

Angeraten ist ein Notschalter, der in der Nähe der Automatisierung

angebracht wird (verbunden mit dem Eingang STOP der Steuerpla-

tine), so dass ein sofortiges Anhalten bei Gefahr möglich ist.

Diese Vorrichtung eignet sich nicht für Personen (einschließlich Kin-

der) mit eingeschränkten körperlichen, geistigen oder Sinnesfähig-

keiten, oder denen die nötige Erfahrung oder die Kenntnisse fehlen,

es sei denn, sie werden von einer für ihre Sicherheit verantwortli-

chen Person begleitet oder beaufsichtigt oder in der Benutzung der

Vorrichtung unterwiesen.

Vergewissern Sie sich vor der Inbetriebsetzung der Automatisie-

rung, dass sich keine Personen in unmittelbarer Nähe benden;

Vor jeder Reinigung und Wartung ist die Automatisierung vom

Stromnetz zu trennen;

Besondere Vorsicht ist geboten, um Quetschungen zwischen dem

geführten Teil und festen Elementen in der unmittelbaren Nähe zu

vermeiden;

Kinder sollten beaufsichtigt werden, um sicherzustellen, dass sie

nicht mit dem Gerät spielen.

Das Verpackungsmaterial aller Automatisierungskomponen-

ten muss entsprechend den örtlichen Bestimmungen entsorgt

werden.

Das Verpackungsmaterial aller Automatisierungskomponen-

ten muss entsprechend den örtlichen Bestimmungen entsorgt

werden.

Marantec behält sich vor, diese Anweisungen notfalls zu ändern;

diese Anweisungen und/oder eine neuere Version benden sich auf

der Website www.marantec.com

ACHTUNG !

19

DE

24 VAC

M1+

M1-

M2+

M2-

COM

FLASH

IND ELEC

LED

v+

ENC M1

ENC M2

NEG

PH POW

EDGE

PH2

PH1

OPEN

CLOSE

SBS

PAR

COM

SHIELD

ANT

POWER

SUPPLY

ON

EDGE

PH2

PH1

BATTERIES

13 1

2

4

35

68 7 15

910

12

13

11

14

16

17

2.1 - Beschreibung des Steuergerätes

Das Steuergerät CBX20324 ist das modernste und ezienteste Be-

triebssystem für die Motoren von Marantec zum elektrischen Önen

und Schließen von Drehtore.

Jeder andere unsachgemäße Gebrauch des Steuergerätes ist verbo-

ten.

2.2 - Beschreibung der Anschlüsse

1- Versorgungsanschlüsse Motor

2- Versorgungsanschlüsse Transformator

3- Ausgangsverbindungen 24Vdc und 24Vac, Bedienelemente

und Sicherheitsvorrichtungen

4- Verbinder für batterieladegerät KBP

5- Anschluss Blinklicht, Zusatzlicht, Kontrolllämpchen Tor

geönet/Elektroschloss

6- Display für Funktionsanzeigen

7- Dip Switch Sicherheitsvorrichtungen

8- Sicherung 2AT träge

9- EDGE-PH2-PH1-OPEN-CLOSE-PAR-SBS Sicherheits-LEDs

und Eingabe-LEDs

10- Taste SBS-STUFUNG ( )

11- Taste UP ( )

12- Taste MENU ( )

13- Taste DOWON und RADIO-Menü ( )

14- Antenne

15- KEY Led

16- Geberanschlüsse

17- Stand-by-Anschlüsse (optional)

2.3 - Modelle und technische Eigenschaften

Das CBX20324ist mit einem Display ausgestattet, das eine einfache

Programmierung und kontinuierliche Überwachung des Status der

Eingänge erlaubt. Außerdem gewährleistet der Menüaufbau eine

einfache Einstellung der Arbeitszeiten und der Betriebslogik.

2 - EINFÜHRUNG IN DAS PRODUKT

CODE BESCHREIBUNG

CBX20324H Steuergerät 24V für zwei Motoren für Drehtore in box (transformator 250 VA)

CBX20324L Steuergerät 24V für zwei Motoren für Drehtore in box (transformator 150 VA)

CBX20324 Steuergerät 24V für zwei Motoren für Drehtore (solo Steuergerät)

- Netzteil mit Kurzschlussschutz im Inneren der Steuereinheit und

an den angeschlossenen Zubehörteilen;

- Hinderniserkennung.

- Automatisches Erlernen der Arbeitszeit.

2 - EINFÜHRUNG IN DAS PRODUKT

20

DE

20

3 - VORABKONTROLLEN

Vor der Installation bitte folgende Punkte prüfen und kontrollieren:

Prüfen, dass das Tor, die Tür oder die Schranke für eine Automati-

sierung geeignet sind;

das Gewicht und die Abmessungen des Tores bzw. der Tür sowie

der Ausgleich des Schrankenbaums müssen innerhalb der Einsa-

tz-Grenzbestimmungen des Antriebes liegen, auf den das Produkt

installiert wird;

kontrolle des Vorhandenseins und der Stärke der mechanischen

Sicherheitsanschläge des Tors oder der Tür;

sicherstellen, dass der Befestigungsbereich nicht überutet werden

kann;

überhöhter Säure- oder Salzgehalt oder die Nähe von Wärmequell-

en können eine Funktionsstörung des Produktes verursachen;

bei extremen klimatischen Verhältnissen (wie z. B. Schnee, Eis,

hohe Temperaturunterschiede, hohe Temperaturen) könnten sich

die Reibungen verstärken; deshalb könnte der Kraftaufwand für

die Bewegung und das Anlaufmoment höher sein als im Normal-

zustand;

kontrollieren, dass eine sanfte manuelle Bewegung des Tors, der

Tür bzw. Schranke ohne Stellen mit stärkerem Widerstand möglich

ist und dass kein Risiko des Austreten aus den Führungsschienen

besteht;

kontrollieren, dass das Tor, die Tür bzw. Schranke im Gleichgewicht

sind und daher in jeder beliebigen Position stehen bleiben;

prüfen, dass die Stromleitung für den Anschluss des Produkts über

eine Sicherheitserdung verfügt und mit einem Leitungsschutz- und

Dierentialschalter geschützt ist;

im Stromnetz der Anlage eine Abschaltvorrichtung mit ausreichen-

dem Önungsabstand der Kontakte vorsehen, die, wie von der

Überspannungskategorie III gefordert, die komplette Abschaltung

erlaubt;

sicherstellen, dass das gesamte für die Installation benutzte Mate-

rial den geltenden Bestimmungen entspricht.

2.4 - Liste benötigter Kabel

Die bei einer typischen Anlage erforderlichen Kabel für den An-

schluss der einzelnen Vorrichtungen sind in der Tabelle Kabelliste

aufgeführt.

Die benutzten Kabel müssen dem Installationstyp entsprechen; z. B.

wird ein Kabel des Typs H03VV-F für Innenbereiche bzw. H07RN-F

für Außenbereiche empfohlen.

* Wenn das Versorgungskabel länger als 30 ist, muss ein Kabel mit größerem Querschnitt benutzt (3x2,5 mm2) und eine Sicherheitserdung

in der Nähe der Automatisierung installiert werden.

** Alternativ können zwei Kabel 2 x 0,5 mm2 verwendet werden

TECHNISCHE SPEZIFIKATIONEN FÜR ELEKTRISCHE KABEL

Anschluss kabelliste maximal zulässige Grenze

Elektrische Versorgungsleitung 1 x kabel 3 x 1,5 mm220 m *

Blinkleuchte, zusätzliche Beleuchtung

Antenne

3 x 0,5 mm2 **

1 x kabel typ RG58

20 m

20 m (empfohlen < 5 m)

Elektroschloss 1 x kabel 2 x 1 mm210 m

Fotozellen Sender 1 x kabel 2 x 0,5 mm220 m

Fotozellen Empfänger 1 x kabel 4 x 0,5 mm220 m

Schaltleiste 1 x kabel 2 x 0,5 mm220 m

Schlüsseltaster 1 x kabel 4 x 0,5 mm2 ** 20 m

Motorstromleitung 1 x kabel 2 x 1,5 mm210 m

Versorgungsleitung Encoder 1 x kabel 3 x 0,5 mm210 m

TECHNISCHE MERKMALE CBX20324H CBX20324L CBX20324

Spannungsversorgung (L-N) 230Vac (+10% - 15%) 50/60 Hz 24 Vdc (+10% - 15%)

Nennleistung 280W maximal 210W maximal -

Ausgang Spannungsversorgung Fotozellen 24Vdc (non regolato) maximal 250mA

Ausgang Spannungsversorgung Zubehör Vac / Spannungsver-

sorgung Gerätetest Vdc 24 Vac ungeregelt 200 mA / 24 Vdc ungeregelt 250 mA

Ausgang Blinkleuchte 24Vdc (ungeregelt) 15W

Ausgang zusätzliche Beleuchtung 24Vdc (ungeregelt) 15W

Ausgang Elektroschloss 12Vac 15VA maximal

Ausgang Kontrollleuchte Tor geönet 24Vdc (ungeregelt) 5W

Eingang Antenne 50Ω Kabel Typ RG58

Betriebstemperatur -20°C + 55°C

Sicherungen Zubehör 2AT

Sicherungen Versorgungsleitung 1.6AT -

Max. Anzahl speicherbare Sender

Kompatibel mit allen Marantec „Bi-Linked“ -Sendern 200

Benutzung in besonders säure- oder salzhaltiger oder explo-

siver Umgebung NO

Schutzart IP54 IPXX

Abmessungen des Steuergerätes 222 x 110 x 275 H mm

Gewicht 3,93 kg 245 g

- Ausschaltung der Sicherheitseingänge durch Dip Switch:

Die Klemmen der nicht installierten Sicherheitsvorrichtungen

müssen nicht überbrückt werden; es reicht aus, die Funktion mit Dip

Switch zu sperren.

La pagina sta caricando ...

Key Automation 580CT20324W Manuale utente

Key Automation 580CT20324W Manuale utente

in altre lingue

Documenti correlati

Altri documenti